Due to missing indication of address decode source (LBW/HBW bus),
we should always try and fetch extended information.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Currently, we rely on COMMS protocol's ack to verify that WFE command
has been acknowledged by the FW. However, this does not guarantee that
the device status has been updated.
Although unlikely, this could trigger a race since the driver expects
the device to be halted at that stage, but it might not be.
Therefore, we increase WFE's robustness by polling on the status
register that will be updated once the device is actually halted.
Signed-off-by: Koby Elbaz <kelbaz@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Currently the debugfs root folder and files for a device are created at
an early step, before the device initialization and before the char
device and sysfs files are exposed to user.
As there is no real reason not to do it together with the device
creation, postpone it to be done right afterwards.
The initialization of the debugfs entry structure is left in its
current position because it is used before creating the files.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Currently upon a heartbeat failure, we don't know if the failure
is due to firmware hang or due to a bad PCI link. Hence, we
are reading a PCI config space register with a known value (vendor ID)
so we will know which of the two possibilities caused the heartbeat
failure.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
For some reason the last possible tpc interrupt cause in
gaudi2_tpc_interrupts_cause is missing from the code.
Signed-off-by: Dafna Hirschfeld <dhirschfeld@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Aborting CS completions should be in command_submission.c but aborting
waiting for user interrupts should be in device.c.
This separation is also for adding more abort operations in the future.
Signed-off-by: Koby Elbaz <kelbaz@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Sync Stream Encapsulated Signal Handlers can be managed from different
contexts, and as such they are protected via a spin_lock.
However, spin_lock was unnecessarily protecting a larger code section
than really needed, covering a sleepable code section as well.
Since spin_lock disables preemption, it could lead to sleeping in
atomic context.
Signed-off-by: Koby Elbaz <kelbaz@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
This commit modifies the call to retrieve HW or FW error events to
return success when no events are pending, as done in the calls to
other events.
Signed-off-by: Moti Haimovski <mhaimovski@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
User needs to be able to perform downcast / upcast of fp8_143 dtype.
Hence bias register needs to be accessed by the user.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
This is done depending on the FW version. The cpucp method is
preferable and saves scratchpads resource.
Signed-off-by: Dafna Hirschfeld <dhirschfeld@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The fw inner version is less trustable, instead use the fw general
sw release version.
Signed-off-by: Dafna Hirschfeld <dhirschfeld@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
It is not always possible to know the FW's SW version from the inner FW
version. Therefore we should extract the general SW version in addition
to the FW version and use it in functions like
'hl_is_fw_ver_below_1_9' etc.
Signed-off-by: Dafna Hirschfeld <dhirschfeld@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
We later want to add fields for Firmware SW version. The current
extracted FW version is the inner FW versioning so the new name
is better and also better differentiate from the FW's SW version.
Signed-off-by: Dafna Hirschfeld <dhirschfeld@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
the helper is extract_u32_until_given_char and can later be used to
also get the major/minor of the sw version.
Signed-off-by: Dafna Hirschfeld <dhirschfeld@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
This commit fixes a bug in Gaudi2 when freeing the scratchpad memory
in case software init fails.
Signed-off-by: Moti Haimovski <mhaimovski@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Once it was decided that these security settings are to be done by FW
rather than by the driver, there's no reason to keep them in the code.
Signed-off-by: Koby Elbaz <kelbaz@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
EDMA transpose workload requires to signal for every activation.
User FW sends all the dummy signals to RD_LBW_RATE_LIM_CFG, to save
lbw bandwidth. We need the user to be able to access that register to
configure it.
Signed-off-by: Rakesh Ughreja <rughreja@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In Gaudi2 asic, PSOC RAZWI may cause in HBW or LBW. The address that
caused the error is read from HW register and printed by the Driver.
There are cases where the Driver receives an indication on PSOC
RAZWI error but the address value is zero. In that case, the indication
is a false positive.
The Driver should not "count" a PSOC RAZWI event error when the
caused the address is zeroed.
Signed-off-by: Tal Cohen <talcohen@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
gcc with W=1 reports
drivers/accel/habanalabs/gaudi/gaudi.c:117:19: error:
‘gaudi_irq_name’ defined but not used [-Werror=unused-const-variable=]
117 | static const char gaudi_irq_name[GAUDI_MSI_ENTRIES][GAUDI_MAX_STRING_LEN] = {
| ^~~~~~~~~~~~~~
This variable is not used so remove it.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Use the regular fbdev helpers for framebuffer I/O instead of DRM's
helpers. Msm does not use damage handling, so DRM's fbdev helpers
are mere wrappers around the fbdev code.
By using fbdev helpers directly within each DRM fbdev emulation,
we can eventually remove DRM's wrapper functions entirely.
Msm's fbdev emulation has been incomplete as it didn't implement
damage handling. Partilly fix this by implementing damage handling
for write and draw operation. It is still missing for mmaped pages.
v4:
* use initializer macros for struct fb_ops
* partially support damage handling
v2:
* use FB_SYS_HELPERS option
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Abhinav Kumar <quic_abhinavk@quicinc.com>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20230530151228.22979-12-tzimmermann@suse.de
Export drm_fb_helper_damage() and drm_fb_helper_damage_range(), which
handle damage areas for fbdev emulation. This is a temporary export
that allows to move the DRM I/O helpers for fbdev into drivers. Only
fbdev-generic and i915 need them. Both will be updated to implement
damage handling by themselves and the exported functions will be removed.
v4:
* update interfaces
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230530151228.22979-11-tzimmermann@suse.de
Use the regular fbdev helpers for framebuffer I/O instead of DRM's
helpers. Fbdev-dma does not use damage handling, so DRM's fbdev helpers
are mere wrappers around the fbdev code.
By using fbdev helpers directly within each DRM fbdev emulation,
we can eventually remove DRM's wrapper functions entirely.
v4:
* use initializer macros for struct fb_ops
v2:
* use FB_SYS_HELPERS option
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230530151228.22979-8-tzimmermann@suse.de
Use the regular fbdev helpers for framebuffer I/O instead of DRM's
helpers. Gma500 does not use damage handling, so DRM's fbdev helpers
are mere wrappers around the fbdev code.
By using fbdev helpers directly within each DRM fbdev emulation,
we can eventually remove DRM's wrapper functions entirely.
v4:
* use initializer macros for struct fb_ops
v2:
* use FB_IO_HELPERS option
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230530151228.22979-6-tzimmermann@suse.de
Use the regular fbdev helpers for framebuffer I/O instead of DRM's
helpers. Armada does not use damage handling, so DRM's fbdev helpers
are mere wrappers around the fbdev code.
By using fbdev helpers directly within each DRM fbdev emulation,
we can eventually remove DRM's wrapper functions entirely.
v4:
* use initializer macros for struct fb_ops
v2:
* use FB_IO_HELPERS option
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Russell King <linux@armlinux.org.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20230530151228.22979-4-tzimmermann@suse.de
For framebuffers in I/O and system memory, add macros that set
struct fb_ops to the respective callback functions.
For deferred I/O, add macros that generate callback functions with
damage handling. Add initializer macros that set struct fb_ops to
the generated callbacks.
These macros can remove a lot boilerplate code from fbdev drivers.
The drivers are supposed to use the macro that is required for its
framebuffer. Each macro is split into smaller helpers, so that
drivers with non-standard callbacks can pick and customize callbacks
as needed. There are individual helper macros for read/write, mmap
and drawing.
v5:
* fix whitespace errors (Jingfeng)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230530151228.22979-3-tzimmermann@suse.de
Backmerging from drm-next to get commit e24e6d6953 ("drm/i915/display:
Implement fb_mmap callback function").
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Use port-base reference for port@1.
This fixes the following schema warning:
imx8mp-dhcom-pdk3.dtb: dsi@32e60000: ports:port@1:endpoint: Unevaluated properties are not allowed ('data-lanes' was unexpected)
From schema: Documentation/devicetree/bindings/display/bridge/samsung,mipi-dsim.yaml
Fixes: 1f0d40d88f ("dt-bindings: bridge: Convert Samsung MIPI DSIM bridge to yaml")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
[narmstrong: removed line break between tags]
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230531224407.1611952-1-festevam@gmail.com
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
panel_edp_remove() always returned zero, so convert it to return void
without any loss and then just drop the return from
panel_edp_platform_remove().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230530074216.2195962-1-u.kleine-koenig@pengutronix.de
In the event a device is connected to the samsung-dsim
controller that doesn't support the burst-clock, the
driver is able to get the requested pixel clock from the
attached device or bridge. In these instances, the
samsung,burst-clock-frequency isn't needed, so remove
it from the required list.
The pll-clock frequency can be set by the device tree entry
for samsung,pll-clock-frequency, but in some cases, the
pll-clock may have the same clock rate as sclk_mipi clock.
If they are equal, this flag is not needed since the driver
will use the sclk_mipi rate as a fallback.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230528132727.3933-1-aford173@gmail.com
