Jiawen Wu says:
====================
support more link mode for TXGBE
There are three new interface mode support for Wangxun 10Gb NICs:
1000BASE-X, SGMII and XAUI.
Specific configurations are added to XPCS. And external PHY attaching
is added for copper NICs.
v2 -> v3:
- add device identifier read
- restrict pcs soft reset
- add firmware version warning
v1 -> v2:
- use the string "txgbe_pcs_mdio_bus" directly
- use dev_err() instead of pr_err()
- add device quirk flag
- add more macro definitions to explain PMA registers
- move txgbe_enable_sec_tx_path() to mac_finish()
- implement phylink for copper NICs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Registers of mdio accessing are common defined in libwx, remove the
redundant macro definitions in ngbe driver.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wangxun SP chip supports to connect with external PHY (marvell 88x3310),
which links to 10GBASE-T/1000BASE-T/100BASE-T. Add the identification of
media types from subsystem device IDs. For sp_media_copper, register mdio
bus for the external PHY.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable data path before PCS VR reset while switching PCS mode, to prevent
the blocking of data path. Enable AN interrupt for CL37 auto-negotiation.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since XPCS device identifier is implemented in the firmware version
0x20010 and above, so add a warning to prompt the users to upgrade the
firmware to make sure the driver works.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wangxun NICs support the connection with SFP to RJ45 module. In this case,
PCS need to be configured in SGMII mode.
According to chapter 6.11.1 "SGMII Auto-Negitiation" of DesignWare Cores
Ethernet PCS (version 3.20a) and custom design manual, do the following
configuration when the interface mode is SGMII.
1. program VR_MII_AN_CTRL bit(3) [TX_CONFIG] = 1b (PHY side SGMII)
2. program VR_MII_AN_CTRL bit(8) [MII_CTRL] = 1b (8-bit MII)
3. program VR_MII_DIG_CTRL1 bit(0) [PHY_MODE_CTRL] = 1b
Also CL37 AN in backplane configurations need to be enabled because of the
special hardware design. Another thing to note is that PMA needs to be
reconfigured before each CL37 AN configuration for SGMII, otherwise AN will
fail, although we don't know why.
On this device, CL37_ANSGM_STS (bit[4:1] of VR_MII_AN_INTR_STS) indicates
the status received from remote link during the auto-negotiation, and
self-clear after the auto-negotiation is complete.
Meanwhile, CL37_ANCMPLT_INTR will be set to 1, to indicate CL37 AN is
complete. So add another way to get the state for CL37 SGMII.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable CL37 AN complete interrupt for DW XPCS. It requires to clear the
bit(0) [CL37_ANCMPLT_INTR] of VR_MII_AN_INTR_STS after AN completed.
And there is a quirk for Wangxun devices to enable CL37 AN in backplane
configurations because of the special hardware design.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to chapter 6 of DesignWare Cores Ethernet PCS (version 3.20a)
and custom design manual, add a configuration flow for switching interface
mode.
If the interface changes, the following setting is required:
1. wait VR_XS_PCS_DIG_STS bit(4, 2) [PSEQ_STATE] = 100b (Power-Good)
2. write SR_XS_PCS_CTRL2 to select various PCS type
3. write SR_PMA_CTRL1 and/or SR_XS_PCS_CTRL1 for link speed
4. program PMA registers
5. write VR_XS_PCS_DIG_CTRL1 bit(15) [VR_RST] = 1b (Vendor-Specific
Soft Reset)
6. wait for VR_XS_PCS_DIG_CTRL1 bit(15) [VR_RST] to get cleared
Only 10GBASE-R/SGMII/1000BASE-X modes are planned for the current Wangxun
devices. And there is a quirk for Wangxun devices to switch mode although
the interface in phylink state has not changed, since PCS will change to
default 10GBASE-R when the ethernet driver(txgbe) do LAN reset.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since Wangxun 10Gb NICs require some special configuration on the IP of
Synopsys Designware XPCS, introduce dev_flag for different vendors. Read
OUI from device identifier registers, to detect Wangxun devices.
And xpcs_soft_reset() is skipped to avoid the reset of device identifier
registers.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Differentiate between empty list and None for member lists.
New families may want to create request responses with no attribute.
If we treat those the same as None we end up rendering
a full parsing policy in user space, instead of an empty one.
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Link: https://lore.kernel.org/r/20230824003056.1436637-5-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We look for attributes inside do.request, but there's another
layer of nesting in the spec, look inside do.request.attributes.
This bug had no effect as all global policies we generate (fou)
seem to be full, anyway, and we treat full and empty the same.
Next patch will change the treatment of empty policies.
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Link: https://lore.kernel.org/r/20230824003056.1436637-4-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add devices IDs for the next LOM generations that will be available on the
next Intel Client platforms. This patch provides the initial support for
these devices.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
It is not allowed to call kfree_skb() from hardware interrupt
context or with hardware interrupts being disabled.
So replace kfree_skb() with dev_kfree_skb_irq() under
spin_lock_irqsave(). Compile tested only.
Fixes: baac6276c0 ("Bluetooth: btusb: handle mSBC audio over USB Endpoints")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The quirks table was named "blacklist_table" which isn't a good
description for that table as devices detected using it weren't ignored
by the driver.
Rename the table to match what it actually does.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In the case of a Periodic Synchronized Receiver,
the PA report received from a Broadcaster contains the BASE,
which has information about codec and other parameters of a BIG.
This isnformation is stored and the application can retrieve it
using getsockopt(BT_ISO_BASE).
Signed-off-by: Claudia Draghicescu <claudia.rosu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Not calling hci_(dis)connect_cfm before deleting conn referred to by a
socket generally results to use-after-free.
When cleaning up SCO connections when the parent ACL is deleted too
early, use hci_conn_failed to do the connection cleanup properly.
We also need to clean up ISO connections in a similar situation when
connecting has started but LE Create CIS is not yet sent, so do it too
here.
Fixes: ca1fd42e7d ("Bluetooth: Fix potential double free caused by hci_conn_unlink")
Reported-by: syzbot+cf54c1da6574b6c1b049@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-bluetooth/00000000000013b93805fbbadc50@google.com/
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
There a few instances still using HCI_MAX_AD_LENGTH instead of using
max_adv_len which takes care of detecting what is the actual maximum
length depending on if the controller supports EA or not.
Fixes: 112b5090c2 ("Bluetooth: MGMT: Fix always using HCI_MAX_AD_LENGTH")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This commit implements defer setup support for the Broadcast Sink
scenario: By setting defer setup on a broadcast socket before calling
listen, the user is able to trigger the PA sync and BIG sync procedures
separately.
This is useful if the user first wants to synchronize to the periodic
advertising transmitted by a Broadcast Source, and trigger the BIG sync
procedure later on.
If defer setup is set, once a PA sync established event arrives, a new
hcon is created and notified to the ISO layer. A child socket associated
with the PA sync connection will be added to the accept queue of the
listening socket.
Once the accept call returns the fd for the PA sync child socket, the
user should call read on that fd. This will trigger the BIG create sync
procedure, and the PA sync socket will become a listening socket itself.
When the BIG sync established event is notified to the ISO layer, the
bis connections will be added to the accept queue of the PA sync parent.
The user should call accept on the PA sync socket to get the final bis
connections.
Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add support for the WCN7850 Bluetooth chipset.
Tested on the SM8550 QRD platform.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use switch/case to handle soc type specific behaviour,
the permit dropping the qca_is_xxx() inline functions
and make the code clearer and easier to update for new
SoCs.
Suggested-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Suggested-by: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fixes sending BT_HCI_CMD_LE_CREATE_CONN_CANCEL when
hci_le_create_conn_sync has not been called because HCI_CONN_SCANNING
has been clear too early before its cmd_sync callback has been run.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use-after-free can occur in hci_disconnect_all_sync if a connection is
deleted by concurrent processing of a controller event.
To prevent this the code now tries to iterate over the list backwards
to ensure the links are cleanup before its parents, also it no longer
relies on a cursor, instead it always uses the last element since
hci_abort_conn_sync is guaranteed to call hci_conn_del.
UAF crash log:
==================================================================
BUG: KASAN: slab-use-after-free in hci_set_powered_sync
(net/bluetooth/hci_sync.c:5424) [bluetooth]
Read of size 8 at addr ffff888009d9c000 by task kworker/u9:0/124
CPU: 0 PID: 124 Comm: kworker/u9:0 Tainted: G W
6.5.0-rc1+ #10
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS
1.16.2-1.fc38 04/01/2014
Workqueue: hci0 hci_cmd_sync_work [bluetooth]
Call Trace:
<TASK>
dump_stack_lvl+0x5b/0x90
print_report+0xcf/0x670
? __virt_addr_valid+0xdd/0x160
? hci_set_powered_sync+0x2c9/0x4a0 [bluetooth]
kasan_report+0xa6/0xe0
? hci_set_powered_sync+0x2c9/0x4a0 [bluetooth]
? __pfx_set_powered_sync+0x10/0x10 [bluetooth]
hci_set_powered_sync+0x2c9/0x4a0 [bluetooth]
? __pfx_hci_set_powered_sync+0x10/0x10 [bluetooth]
? __pfx_lock_release+0x10/0x10
? __pfx_set_powered_sync+0x10/0x10 [bluetooth]
hci_cmd_sync_work+0x137/0x220 [bluetooth]
process_one_work+0x526/0x9d0
? __pfx_process_one_work+0x10/0x10
? __pfx_do_raw_spin_lock+0x10/0x10
? mark_held_locks+0x1a/0x90
worker_thread+0x92/0x630
? __pfx_worker_thread+0x10/0x10
kthread+0x196/0x1e0
? __pfx_kthread+0x10/0x10
ret_from_fork+0x2c/0x50
</TASK>
Allocated by task 1782:
kasan_save_stack+0x33/0x60
kasan_set_track+0x25/0x30
__kasan_kmalloc+0x8f/0xa0
hci_conn_add+0xa5/0xa80 [bluetooth]
hci_bind_cis+0x881/0x9b0 [bluetooth]
iso_connect_cis+0x121/0x520 [bluetooth]
iso_sock_connect+0x3f6/0x790 [bluetooth]
__sys_connect+0x109/0x130
__x64_sys_connect+0x40/0x50
do_syscall_64+0x60/0x90
entry_SYSCALL_64_after_hwframe+0x6e/0xd8
Freed by task 695:
kasan_save_stack+0x33/0x60
kasan_set_track+0x25/0x30
kasan_save_free_info+0x2b/0x50
__kasan_slab_free+0x10a/0x180
__kmem_cache_free+0x14d/0x2e0
device_release+0x5d/0xf0
kobject_put+0xdf/0x270
hci_disconn_complete_evt+0x274/0x3a0 [bluetooth]
hci_event_packet+0x579/0x7e0 [bluetooth]
hci_rx_work+0x287/0xaa0 [bluetooth]
process_one_work+0x526/0x9d0
worker_thread+0x92/0x630
kthread+0x196/0x1e0
ret_from_fork+0x2c/0x50
==================================================================
Fixes: 182ee45da0 ("Bluetooth: hci_sync: Rework hci_suspend_notifier")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This improves the inband IR command handling for NXP BT chipsets.
When the IR vendor command is received, the driver injects a HW
error event, which causes a reset sequence in hci_error_reset().
The vendor IR command is sent to the controller while hci dev
is been closed, and FW is re-downloaded when nxp_setup() is
called during hci_dev_do_open().
The HCI_SETUP flag is set in nxp_hw_err() to make sure that
nxp_setup() is been called during hci_dev_do_open().
This also makes the nxp_setup() and power save functions more
generic.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds support for NXP IW624 chipset in btnxpuart driver
by adding FW name and bootloader signature. Based on the
loader version bits 7:6 of the bootloader signature, the
driver can choose between selecting secure and non-secure
FW files.
For cmd5 payload during FW download, this chip has addresses
of few registers offset by 1, so added boot_reg_offset to
handle the chip specific offset.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This removes the unnecessary check for CTS low after FW download.
After FW download is complete, the CTS line is already seen low.
It becomes high after 2 msec, and low again after FW initialization
is complete.
This makes the current check for CTS low redundant.
This removes the wait for CTS low section and increase delay to
1200msec instead, which is sufficiant for all NXP chipsets to
initialize FW.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Leon Romanovsky says:
====================
mlx5 MACsec RoCEv2 support
From Patrisious:
This series extends previously added MACsec offload support
to cover RoCE traffic either.
In order to achieve that, we need configure MACsec with offload between
the two endpoints, like below:
REMOTE_MAC=10:70:fd:43:71:c0
* ip addr add 1.1.1.1/16 dev eth2
* ip link set dev eth2 up
* ip link add link eth2 macsec0 type macsec encrypt on
* ip macsec offload macsec0 mac
* ip macsec add macsec0 tx sa 0 pn 1 on key 00 dffafc8d7b9a43d5b9a3dfbbf6a30c16
* ip macsec add macsec0 rx port 1 address $REMOTE_MAC
* ip macsec add macsec0 rx port 1 address $REMOTE_MAC sa 0 pn 1 on key 01 ead3664f508eb06c40ac7104cdae4ce5
* ip addr add 10.1.0.1/16 dev macsec0
* ip link set dev macsec0 up
And in a similar manner on the other machine, while noting the keys order
would be reversed and the MAC address of the other machine.
RDMA traffic is separated through relevant GID entries and in case
of IP ambiguity issue - meaning we have a physical GIDs and a MACsec
GIDs with the same IP/GID, we disable our physical GID in order
to force the user to only use the MACsec GID.
v0: https://lore.kernel.org/netdev/20230813064703.574082-1-leon@kernel.org/
* 'mlx5-next' of https://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
RDMA/mlx5: Handles RoCE MACsec steering rules addition and deletion
net/mlx5: Add RoCE MACsec steering infrastructure in core
net/mlx5: Configure MACsec steering for ingress RoCEv2 traffic
net/mlx5: Configure MACsec steering for egress RoCEv2 traffic
IB/core: Reorder GID delete code for RoCE
net/mlx5: Add MACsec priorities in RDMA namespaces
RDMA/mlx5: Implement MACsec gid addition and deletion
net/mlx5: Maintain fs_id xarray per MACsec device inside macsec steering
net/mlx5: Remove netdevice from MACsec steering
net/mlx5e: Move MACsec flow steering and statistics database from ethernet to core
net/mlx5e: Rename MACsec flow steering functions/parameters to suit core naming style
net/mlx5: Remove dependency of macsec flow steering on ethernet
net/mlx5e: Move MACsec flow steering operations to be used as core library
macsec: add functions to get macsec real netdevice and check offload
====================
Link: https://lore.kernel.org/r/20230821073833.59042-1-leon@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove the necessity to modify skb_ext_total_length() when new extension
types are added.
Also reduces the line count a bit.
With optimizations enabled the function is folded down to the same
constant value as before during compilation.
This has been validated on x86 with GCC 6.5.0 and 13.2.1.
Also a similar construct has been validated on godbolt.org with GCC 5.1.
In any case the compiler has to be able to evaluate the construct at
compile-time for the BUILD_BUG_ON() in skb_extensions_init().
Even if not evaluated at compile-time this function would only ever
be executed once at run-time, so the overhead would be very minuscule.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230823-skb_ext-simplify-v2-1-66e26cd66860@weissschuh.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For LDX_B/H/W, when zext has been inserted by verifier, it'll return 1,
and no exception handling will continue. Also, when the offset is 12-bit
value, the redundant zext inserted by the verifier is not removed. Fix
both scenarios by moving down the removal of redundant zext.
Signed-off-by: Pu Lehui <pulehui@huawei.com>
Link: https://lore.kernel.org/r/20230824095001.3408573-2-pulehui@huaweicloud.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Toke Høiland-Jørgensen says:
====================
samples/bpf: Remove unmaintained XDP sample utilities
The samples/bpf directory in the kernel tree started out as a way of showcasing
different aspects of BPF functionality by writing small utility programs for
each feature. However, as the BPF subsystem has matured, the preferred way of
including userspace code with a feature has become the BPF selftests, which also
have the benefit of being consistently run as part of the BPF CI system.
As a result of this shift, the utilities in samples/bpf have seen little love,
and have slowly bitrotted. There have been sporadic cleanup patches over the
years, but it's clear that the utilities are far from maintained.
For XDP in particular, some of the utilities have been used as benchmarking aids
when implementing new kernel features, which seems to be the main reason they
have stuck around; any updates the utilities have seen have been targeted at
this use case. However, as the BPF subsystem as a whole has moved on, it has
become increasingly difficult to incorporate new features into these utilities
because they predate most of the modern BPF features (such as kfuncs and BTF).
Rather than try to update these utilities and keep maintaining them in the
kernel tree, we have ported the useful features of the utilities to the
xdp-tools package. In the porting process we also updated the utilities to take
advantage of modern BPF features, integrated them with libxdp, and polished the
user interface.
As these utilities are standalone tools, maintaining them out of tree is
simpler, and we plan to keep maintaining them in the xdp-tools repo. To direct
users of these utilities to the right place, this series removes the utilities
from samples/bpf, leaving in place only a couple of utilities whose
functionality have not yet been ported to xdp-tools.
The xdp-tools repository is located on Github at the following URL:
https://github.com/xdp-project/xdp-tools
The commits in the series removes one utility each, explaining how the
equivalent functionality can be obtained with xdp-tools.
v2:
- Add equivalent xdp-tools commands for each removed utility
v3:
- Add link to xdp-tools in the README
Toke Høiland-Jørgensen (7):
samples/bpf: Remove the xdp_monitor utility
samples/bpf: Remove the xdp_redirect* utilities
samples/bpf: Remove the xdp_rxq_info utility
samples/bpf: Remove the xdp1 and xdp2 utilities
samples/bpf: Remove the xdp_sample_pkts utility
samples/bpf: Cleanup .gitignore
samples/bpf: Add note to README about the XDP utilities moved to
xdp-tools
samples/bpf/.gitignore | 12 -
samples/bpf/Makefile | 48 +-
samples/bpf/README.rst | 6 +
samples/bpf/xdp1_kern.c | 100 ----
samples/bpf/xdp1_user.c | 166 ------
samples/bpf/xdp2_kern.c | 125 -----
samples/bpf/xdp_monitor.bpf.c | 8 -
samples/bpf/xdp_monitor_user.c | 118 -----
samples/bpf/xdp_redirect.bpf.c | 49 --
samples/bpf/xdp_redirect_cpu.bpf.c | 539 -------------------
samples/bpf/xdp_redirect_cpu_user.c | 559 --------------------
samples/bpf/xdp_redirect_map.bpf.c | 97 ----
samples/bpf/xdp_redirect_map_multi.bpf.c | 77 ---
samples/bpf/xdp_redirect_map_multi_user.c | 232 --------
samples/bpf/xdp_redirect_map_user.c | 228 --------
samples/bpf/xdp_redirect_user.c | 172 ------
samples/bpf/xdp_rxq_info_kern.c | 140 -----
samples/bpf/xdp_rxq_info_user.c | 614 ----------------------
samples/bpf/xdp_sample_pkts_kern.c | 57 --
samples/bpf/xdp_sample_pkts_user.c | 196 -------
20 files changed, 7 insertions(+), 3536 deletions(-)
delete mode 100644 samples/bpf/xdp1_kern.c
delete mode 100644 samples/bpf/xdp1_user.c
delete mode 100644 samples/bpf/xdp2_kern.c
delete mode 100644 samples/bpf/xdp_monitor.bpf.c
delete mode 100644 samples/bpf/xdp_monitor_user.c
delete mode 100644 samples/bpf/xdp_redirect.bpf.c
delete mode 100644 samples/bpf/xdp_redirect_cpu.bpf.c
delete mode 100644 samples/bpf/xdp_redirect_cpu_user.c
delete mode 100644 samples/bpf/xdp_redirect_map.bpf.c
delete mode 100644 samples/bpf/xdp_redirect_map_multi.bpf.c
delete mode 100644 samples/bpf/xdp_redirect_map_multi_user.c
delete mode 100644 samples/bpf/xdp_redirect_map_user.c
delete mode 100644 samples/bpf/xdp_redirect_user.c
delete mode 100644 samples/bpf/xdp_rxq_info_kern.c
delete mode 100644 samples/bpf/xdp_rxq_info_user.c
delete mode 100644 samples/bpf/xdp_sample_pkts_kern.c
delete mode 100644 samples/bpf/xdp_sample_pkts_user.c
====================
Link: https://lore.kernel.org/r/20230824102255.1561885-1-toke@redhat.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
