The stop trigger invokes rz_ssi_stop() and rz_ssi_stream_quit().
- The purpose of rz_ssi_stop() is to disable TX/RX, terminate DMA
transactions, and set the controller to idle.
- The purpose of rz_ssi_stream_quit() is to reset the substream-specific
software data by setting strm->running and strm->substream appropriately.
The function rz_ssi_is_stream_running() checks if both strm->substream and
strm->running are valid and returns true if so. Its implementation is as
follows:
static inline bool rz_ssi_is_stream_running(struct rz_ssi_stream *strm)
{
return strm->substream && strm->running;
}
When the controller is configured in full-duplex mode (with both playback
and capture active), the rz_ssi_stop() function does not modify the
controller settings when called for the first substream in the full-duplex
setup. Instead, it simply sets strm->running = 0 and returns if the
companion substream is still running. The following code illustrates this:
static int rz_ssi_stop(struct rz_ssi_priv *ssi, struct rz_ssi_stream *strm)
{
strm->running = 0;
if (rz_ssi_is_stream_running(&ssi->playback) ||
rz_ssi_is_stream_running(&ssi->capture))
return 0;
// ...
}
The controller settings, along with the DMA termination (for the last
stopped substream), are only applied when the last substream in the
full-duplex setup is stopped.
While applying the controller settings only when the last substream stops
is not problematic, terminating the DMA operations for only one substream
causes failures when starting and stopping full-duplex operations multiple
times in a loop.
To address this issue, call dmaengine_terminate_async() for both substreams
involved in the full-duplex setup when the last substream in the setup is
stopped.
Fixes: 4f8cd05a43 ("ASoC: sh: rz-ssi: Add full duplex support")
Cc: stable@vger.kernel.org
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20241210170953.2936724-5-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>:
These patches tidyup simple-card-utils for Multi connection of
Audio Graph Card, Because of DT node parsing, it should check port
1st instead of endpoint. Otherwise, it can't handle DAI correctly.
Merge series from Chancel Liu <chancel.liu@nxp.com>:
Platforms like i.MX93/91 only have one audio PLL. Some sample rates are
not supported. If the PLL source is used for 8kHz series rates, then
11kHz series rates can't be supported. Add common function to constrain
rates according to different clock sources.
In ASoC drivers switch to this new function.
Merge series from codekipper@gmail.com:
I've tested this patch series on the Allwinner H3, A64, H6 and H313 SoCs
up to 192KHz.
24bit support is working on my H313 board but 16bit plays a bit slow and
I suspect that there is an issue with the clock setups. This is even
present without this patch stack. I would look to address this asap,
but for now can you please review what's here.
There have been intermittent issues with the SPDIF output on H3
and H2+ devices which has been fixed by setting the s_clk to 4
times the audio pll.
Add a quirk for the clock multiplier as not every supported SoC
requires it. Without the multiplier, the audio at normal sampling
rates was distorted and did not play at higher sampling rates.
Fixes: 1bd92af877 ("ASoC: sun4i-spdif: Add support for the H3 SoC")
Signed-off-by: George Lander <lander@jagmn.com>
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Link: https://patch.msgid.link/20241111165600.57219-2-codekipper@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-21-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-20-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-19-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-18-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-17-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-16-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-15-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-14-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-13-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-12-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-11-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-10-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-9-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-8-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-7-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-6-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-5-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-4-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-3-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-2-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-1-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
