In case we have succeeded to attach a CPU to its PM domain, let's deploy
runtime PM support for the corresponding attached device, to allow the CPU
to be powered-managed accordingly.
The triggering point for when runtime PM reference counting should be done,
has been selected to the deepest idle state for the CPU. However, from the
hierarchical point view, there may be good reasons to do runtime PM
reference counting even on shallower idle states, but at this point this
isn't supported, mainly due to limitations set by the generic PM domain.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
The per CPU variable psci_power_state, contains an array of fixed values,
which reflects the corresponding arm,psci-suspend-param parsed from DT, for
each of the available CPU idle states.
This isn't sufficient when using the hierarchical CPU topology in DT, in
combination with having PSCI OS initiated (OSI) mode enabled. More
precisely, in OSI mode, Linux is responsible of telling the PSCI FW what
idle state the cluster (a group of CPUs) should enter, while in PSCI
Platform Coordinated (PC) mode, each CPU independently votes for an idle
state of the cluster.
For this reason, introduce a per CPU variable called domain_state and
implement two helper functions to read/write its value. Then let the
domain_state take precedence over the regular selected state, when entering
and idle state.
To avoid executing the above OSI specific code in the ->enter() callback,
while operating in the default PSCI Platform Coordinated mode, let's also
add a new enter-function and use it for OSI.
Co-developed-by: Lina Iyer <lina.iyer@linaro.org>
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
In order to enable a CPU to be power managed through its PM domain, let's
try to attach it by calling psci_dt_attach_cpu() during the cpuidle
initialization.
psci_dt_attach_cpu() returns a pointer to the attached struct device, which
later should be used for runtime PM, hence we need to store it somewhere.
Rather than adding yet another per CPU variable, let's create a per CPU
struct to collect the relevant per CPU variables.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Introduce a PSCI DT helper function, psci_dt_attach_cpu(), which takes a
CPU number as an in-parameter and tries to attach the CPU's struct device
to its corresponding PM domain.
Let's makes use of dev_pm_domain_attach_by_name(), as it allows us to
specify "psci" as the "name" of the PM domain to attach to. Additionally,
let's also prepare the attached device to be power managed via runtime PM.
Note that, the implementation of the new helper function is in a new
separate c-file, which may seems a bit too much at this point. However,
subsequent changes that implements the remaining part of the PM domain
support for cpuidle-psci, helps to justify this split.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Currently CPU's idle states are represented using the flattened model.
Let's add support for the hierarchical layout, via converting to use
of_get_cpu_state_node().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Iterating through the idle state nodes in DT, to find out the number of
states that needs to be allocated is unnecessary, as it has already been
done from dt_init_idle_driver(). Therefore, drop the iteration and use the
number we already have at hand.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
The CPU's idle state nodes are currently parsed at the common cpuidle DT
library, but also when initializing data for specific CPU idle operations,
as in the PSCI cpuidle driver case and qcom-spm cpuidle case.
To avoid open-coding, let's introduce of_get_cpu_state_node(), which takes
the device node for the CPU and the index to the requested idle state node,
as in-parameters. In case a corresponding idle state node is found, it
returns the node with the refcount incremented for it, else it returns
NULL.
Moreover, for PSCI there are two options to describe the CPU's idle states
[1], either via a flattened description or a hierarchical layout. Hence,
let's take both options into account.
[1] Documentation/devicetree/bindings/arm/psci.yaml
Suggested-by: Sudeep Holla <sudeep.holla@arm.com>
Co-developed-by: Lina Iyer <lina.iyer@linaro.org>
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
To allow subsequent changes to implement support for OSI mode through the
cpuidle-psci driver, export the existing psci_has_osi_support(). Export
also a new function, psci_set_osi_mode(), that allows its caller to enable
the OS-initiated CPU-suspend mode in the PSCI FW.
To deal with backwards compatibility for a kernel started through a kexec
call, default to set the CPU-suspend mode to the Platform Coordinated mode
during boot.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Update PSCI DT bindings to allow to represent idle states for CPUs and the
CPU topology, by using a hierarchical layout. Primarily this is done by
re-using the existing DT bindings for PM domains [1] and for PM domain idle
states [2].
Let's also add an example into the document for the PSCI DT bindings, to
clearly show the new hierarchical based layout. The currently supported
flattened layout, is already described in the ARM idle states bindings [3],
so let's leave that as is.
[1] Documentation/devicetree/bindings/power/power_domain.txt
[2] Documentation/devicetree/bindings/power/domain-idle-state.txt
[3] Documentation/devicetree/bindings/arm/idle-states.txt
Co-developed-by: Lina Iyer <lina.iyer@linaro.org>
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of allocating 'n-1' states in psci_power_state to manage 'n'
idle states which include "ARM WFI" state, it would be simpler to have
1:1 mapping between psci_power_state and cpuidle driver states.
ARM WFI state(i.e. idx == 0) is handled specially in the generic macro
CPU_PM_CPU_IDLE_ENTER_PARAM and hence state[-1] is not possible. However
for sake of code readability, it is better to have 1:1 mapping and not
use [idx - 1] to access psci_power_state corresponding to driver cpuidle
state for idx.
psci_power_state[0] is default initialised to 0 and is never accessed
while entering WFI state.
Reported-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Pull RISC-V fixes from Paul Walmsley:
"One important fix for RISC-V:
- Redirect any incoming syscall with an ID less than -1 to
sys_ni_syscall, rather than allowing them to fall through into the
syscall handler.
and two minor build fixes:
- Export __asm_copy_{from,to}_user() from where they are defined.
This fixes a build error triggered by some randconfigs.
- Export flush_icache_all(). I'd resisted this before, since
historically we didn't want modules to be able to flush the I$
directly; but apparently everyone else is doing it now"
* tag 'riscv/for-v5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: export flush_icache_all to modules
riscv: reject invalid syscalls below -1
riscv: fix compile failure with EXPORT_SYMBOL() & !MMU
Pull /proc/locks formatting fix from Jeff Layton:
"This is a trivial fix for a _very_ long standing bug in /proc/locks
formatting. Ordinarily, I'd wait for the merge window for something
like this, but it is making it difficult to validate some overlayfs
fixes.
I've also gone ahead and marked this for stable"
* tag 'locks-v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux:
locks: print unsigned ino in /proc/locks
Pull cifs fixes from Steve French:
"One performance fix for large directory searches, and one minor style
cleanup noticed by Clang"
* tag '5.5-rc3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Optimize readdir on reparse points
cifs: Adjust indentation in smb2_open_file
This is needed by LKDTM (crash dump test module), it calls
flush_icache_range(), which on RISC-V turns into flush_icache_all(). On
other architectures, the actual implementation is exported, so follow
that precedence and export it here too.
Fixes build of CONFIG_LKDTM that fails with:
ERROR: "flush_icache_all" [drivers/misc/lkdtm/lkdtm.ko] undefined!
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Running "stress-ng --enosys 4 -t 20 -v" showed a large number of kernel oops
with "Unable to handle kernel paging request at virtual address" message. This
happens when enosys stressor starts testing random non-valid syscalls.
I forgot to redirect any syscall below -1 to sys_ni_syscall.
With the patch kernel oops messages are gone while running stress-ng enosys
stressor.
Signed-off-by: David Abdurachmanov <david.abdurachmanov@sifive.com>
Fixes: 5340627e3f ("riscv: add support for SECCOMP and SECCOMP_FILTER")
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
When support for !MMU was added, the declaration of
__asm_copy_to_user() & __asm_copy_from_user() were #ifdefed
out hence their EXPORT_SYMBOL() give an error message like:
.../riscv_ksyms.c:13:15: error: '__asm_copy_to_user' undeclared here
.../riscv_ksyms.c:14:15: error: '__asm_copy_from_user' undeclared here
Since these symbols are not defined with !MMU it's wrong to export them.
Same for __clear_user() (even though this one is also declared in
include/asm-generic/uaccess.h and thus doesn't give an error message).
Fix this by doing the EXPORT_SYMBOL() directly where these symbols
are defined: inside lib/uaccess.S itself.
Fixes: 6bd33e1ece ("riscv: fix compile failure with EXPORT_SYMBOL() & !MMU")
Reported-by: kbuild test robot <lkp@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Pull SCSI fixes from James Bottomley:
"Four fixes and one spelling update, all in drivers: two in lpfc and
the rest in mp3sas, cxgbi and target"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: target/iblock: Fix protection error with blocks greater than 512B
scsi: libcxgbi: fix NULL pointer dereference in cxgbi_device_destroy()
scsi: lpfc: fix spelling mistakes of asynchronous
scsi: lpfc: fix build failure with DEBUGFS disabled
scsi: mpt3sas: Fix double free in attach error handling
Pull drm fixes from Dave Airlie:
"Post-xmas food coma recovery fixes. Only three fixes for i915 since I
expect most people are holidaying.
i915:
- power management rc6 fix
- framebuffer tracking fix
- display power management ratelimit fix"
* tag 'drm-fixes-2019-12-28' of git://anongit.freedesktop.org/drm/drm:
drm/i915: Hold reference to intel_frontbuffer as we track activity
drm/i915/gt: Ratelimit display power w/a
drm/i915/pmu: Ensure monotonic rc6
Pull Kselftest fixes from Shuah Khan:
- rseq build failures fixes related to glibc 2.30 compatibility from
Mathieu Desnoyers
- Kunit fixes and cleanups from SeongJae Park
- Fixes to filesystems/epoll, firmware, and livepatch build failures
and skip handling.
* tag 'linux-kselftest-5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
rseq/selftests: Clarify rseq_prepare_unload() helper requirements
rseq/selftests: Fix: Namespace gettid() for compatibility with glibc 2.30
rseq/selftests: Turn off timeout setting
kunit/kunit_tool_test: Test '--build_dir' option run
kunit: Rename 'kunitconfig' to '.kunitconfig'
kunit: Place 'test.log' under the 'build_dir'
kunit: Create default config in '--build_dir'
kunit: Remove duplicated defconfig creation
docs/kunit/start: Use in-tree 'kunit_defconfig'
selftests: livepatch: Fix it to do root uid check and skip
selftests: firmware: Fix it to do root uid check and skip
selftests: filesystems/epoll: fix build error
Pull power management fixes from Rafael Wysocki:
"Fix compile test of the Tegra devfreq driver (Arnd Bergmann) and
remove redundant Kconfig dependencies from multiple devfreq drivers
(Leonard Crestez)"
* tag 'pm-5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / devfreq: tegra: Add COMMON_CLK dependency
PM / devfreq: Drop explicit selection of PM_OPP
Pull io_uring fixes from Jens Axboe:
- Removal of now unused busy wqe list (Hillf)
- Add cond_resched() to io-wq work processing (Hillf)
- And then the series that I hinted at from last week, which removes
the sqe from the io_kiocb and keeps all sqe handling on the prep
side. This guarantees that an opcode can't do the wrong thing and
read the sqe more than once. This is unchanged from last week, no
issues have been observed with this in testing. Hence I really think
we should fold this into 5.5.
* tag 'io_uring-5.5-20191226' of git://git.kernel.dk/linux-block:
io-wq: add cond_resched() to worker thread
io-wq: remove unused busy list from io_sqe
io_uring: pass in 'sqe' to the prep handlers
io_uring: standardize the prep methods
io_uring: read 'count' for IORING_OP_TIMEOUT in prep handler
io_uring: move all prep state for IORING_OP_{SEND,RECV}_MGS to prep handler
io_uring: move all prep state for IORING_OP_CONNECT to prep handler
io_uring: add and use struct io_rw for read/writes
io_uring: use u64_to_user_ptr() consistently
Pull libata fixes from Jens Axboe:
"Two things in here:
- First half of a series that fixes ahci_brcm, also marked for
stable. The other part of the series is going into 5.6 (Florian)
- sata_nv regression fix that is also marked for stable (Sascha)"
* tag 'libata-5.5-20191226' of git://git.kernel.dk/linux-block:
ata: ahci_brcm: Add missing clock management during recovery
ata: ahci_brcm: BCM7425 AHCI requires AHCI_HFLAG_DELAY_ENGINE
ata: ahci_brcm: Fix AHCI resources management
ata: libahci_platform: Export again ahci_platform_<en/dis>able_phys()
libata: Fix retrieving of active qcs
Pull block fixes from Jens Axboe:
"Only thing here are the changes from Arnd from last week, which now
have the appropriate header include to ensure they actually compile if
COMPAT is enabled"
* tag 'block-5.5-20191226' of git://git.kernel.dk/linux-block:
compat_ioctl: block: handle Persistent Reservations
compat_ioctl: block: handle add zone open, close and finish ioctl
compat_ioctl: block: handle BLKGETZONESZ/BLKGETNRZONES
compat_ioctl: block: handle BLKREPORTZONE/BLKRESETZONE
pktcdvd: fix regression on 64-bit architectures
Pull GPIO fixes from Linus Walleij:
"A set of fixes for the v5.5 series:
- Fix the build for the Xtensa driver.
- Make sure to set up the parent device for mpc8xxx.
- Clarify the look-up error message.
- Fix the usage of the line direction in the mockup device.
- Fix a type warning on the Aspeed driver.
- Remove the pointless __exit annotation on the xgs-iproc which is
causing a compilation problem.
- Fix up emultation of open drain outputs .get_direction()
- Fix the IRQ callbacks on the PCA953xx to use bitops and work
properly.
- Fix the Kconfig on the Tegra driver"
* tag 'gpio-v5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: tegra186: Allow building on Tegra194-only configurations
gpio: pca953x: Switch to bitops in IRQ callbacks
gpiolib: fix up emulated open drain outputs
MAINTAINERS: Append missed file to the database
gpio: xgs-iproc: remove __exit annotation for iproc_gpio_remove
gpio: aspeed: avoid return type warning
gpio: mockup: Fix usage of new GPIO_LINE_DIRECTION
gpio: Fix error message on out-of-range GPIO in lookup table
gpio: mpc8xxx: Add platform device to gpiochip->parent
gpio: xtensa: fix driver build
The downstream implementation of ahci_brcm.c did contain clock
management recovery, but until recently, did that outside of the
libahci_platform helpers and this was unintentionally stripped out while
forward porting the patch upstream.
Add the missing clock management during recovery and sleep for 10
milliseconds per the design team recommendations to ensure the SATA PHY
controller and AFE have been fully quiesced.
Fixes: eb73390ae2 ("ata: ahci_brcm: Recover from failures to identify devices")
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Set AHCI_HFLAG_DELAY_ENGINE for the BCM7425 AHCI controller thus making
it conforming to the 'strict' AHCI implementation which this controller
is based on.
This solves long link establishment with specific hard drives (e.g.:
Seagate ST1000VM002-9ZL1 SC12) that would otherwise have to complete the
error recovery handling before finally establishing a succesful SATA
link at the desired speed.
We re-order the hpriv->flags assignment to also remove the NONCQ quirk
since we can set the flag directly.
Fixes: 9586114cf1e9 ("ata: ahci_brcmstb: add support MIPS-based platforms")
Fixes: 423be77daabe ("ata: ahci_brcmstb: add quirk for broken ncq")
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The AHCI resources management within ahci_brcm.c is a little
convoluted, largely because it historically had a dedicated clock that
was managed within this file in the downstream tree. Once brough
upstream though, the clock was left to be managed by libahci_platform.c
which is entirely appropriate.
This patch series ensures that the AHCI resources are fetched and
enabled before any register access is done, thus avoiding bus errors on
platforms which clock gate the controller by default.
As a result we need to re-arrange the suspend() and resume() functions
in order to avoid accessing registers after the clocks have been turned
off respectively before the clocks have been turned on. Finally, we can
refactor brcm_ahci_get_portmask() in order to fetch the number of ports
from hpriv->mmio which is now accessible without jumping through hoops
like we used to do.
The commit pointed in the Fixes tag is both old and new enough not to
require major headaches for backporting of this patch.
Fixes: eba68f8297 ("ata: ahci_brcmstb: rename to support across Broadcom SoC's")
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This reverts commit 6bb86fefa0
("libahci_platform: Staticize ahci_platform_<en/dis>able_phys()") we are
going to need ahci_platform_{enable,disable}_phys() in a subsequent
commit for ahci_brcm.c in order to properly control the PHY
initialization order.
Also make sure the function prototypes are declared in
include/linux/ahci_platform.h as a result.
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
ata_qc_complete_multiple() is called with a mask of the still active
tags.
mv_sata doesn't have this information directly and instead calculates
the still active tags from the started tags (ap->qc_active) and the
finished tags as (ap->qc_active ^ done_mask)
Since 28361c4036 the hw_tag and tag are no longer the same and the
equation is no longer valid. In ata_exec_internal_sg() ap->qc_active is
initialized as 1ULL << ATA_TAG_INTERNAL, but in hardware tag 0 is
started and this will be in done_mask on completion. ap->qc_active ^
done_mask becomes 0x100000000 ^ 0x1 = 0x100000001 and thus tag 0 used as
the internal tag will never be reported as completed.
This is fixed by introducing ata_qc_get_active() which returns the
active hardware tags and calling it where appropriate.
This is tested on mv_sata, but sata_fsl and sata_nv suffer from the same
problem. There is another case in sata_nv that most likely needs fixing
as well, but this looks a little different, so I wasn't confident enough
to change that.
Fixes: 28361c4036 ("libata: add extra internal command")
Cc: stable@vger.kernel.org
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add missing export of ata_qc_get_active(), as per Pali.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull devfreq fixes for 5.5-rc4 from Chanwoo Choi:
"1. Fix the build error of tegra*-devfreq.c when COMPILE_TEST is enabled.
2. Drop unneeded PM_OPP dependency from each driver in Kconfig."
* tag 'devfreq-fixes-for-5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/linux:
PM / devfreq: tegra: Add COMMON_CLK dependency
PM / devfreq: Drop explicit selection of PM_OPP
Reschedule the current IO worker to cut the risk that it is becoming
a cpu hog.
Signed-off-by: Hillf Danton <hdanton@sina.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The rseq.h UAPI now documents that the rseq_cs field must be cleared
before reclaiming memory that contains the targeted struct rseq_cs, but
also that the rseq_cs field must be cleared before reclaiming memory of
the code pointed to by the rseq_cs start_ip and post_commit_offset
fields.
While we can expect that use of dlclose(3) will typically unmap
both struct rseq_cs and its associated code at once, nothing would
theoretically prevent a JIT from reclaiming the code without
reclaiming the struct rseq_cs, which would erroneously allow the
kernel to consider new code which is not a rseq critical section
as a rseq critical section following a code reclaim.
Suggested-by: Florian Weimer <fw@deneb.enyo.de>
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Shuah Khan <skhan@linuxfoundation.org>
Cc: Florian Weimer <fw@deneb.enyo.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: "Paul E. McKenney" <paulmck@linux.ibm.com>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: "H . Peter Anvin" <hpa@zytor.com>
Cc: Paul Turner <pjt@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
This commit renames 'kunitconfig' to '.kunitconfig' so that it can be
automatically ignored by git and do not disturb people who want to type
'kernel/' by pressing only the 'k' and then 'tab' key.
Signed-off-by: SeongJae Park <sjpark@amazon.de>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Tested-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
'kunit' writes the 'test.log' under the kernel source directory even
though a 'build_dir' option is given. As users who use the option might
expect the outputs to be placed under the specified directory, this
commit modifies the logic to write the log file under the 'build_dir'.
Signed-off-by: SeongJae Park <sjpark@amazon.de>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Tested-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
'--defconfig' option is handled by the 'main() of the 'kunit.py' but
again handled in following 'run_tests()'. This commit removes this
duplicated handling of the option in the 'run_tests()'.
Signed-off-by: SeongJae Park <sjpark@amazon.de>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Tested-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The kunit doc suggests users to get the default `kunitconfig` from an
external git tree. However, the file is already located under the
`arch/um/configs/` of the kernel tree. Because the local file is easier
to access and maintain, this commit updates the doc to use it.
Signed-off-by: SeongJae Park <sjpark@amazon.de>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Tested-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
livepatch test configures the system and debug environment to run
tests. Some of these actions fail without root access and test
dumps several permission denied messages before it exits.
Fix test-state.sh to call setup_config instead of set_dynamic_debug
as suggested by Petr Mladek <pmladek@suse.com>
Fix it to check root uid and exit with skip code instead.
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Acked-by: Joe Lawrence <joe.lawrence@redhat.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
firmware attempts to load test modules that require root access
and fail. Fix it to check for root uid and exit with skip code
instead.
Before this fix:
selftests: firmware: fw_run_tests.sh
modprobe: ERROR: could not insert 'test_firmware': Operation not permitted
You must have the following enabled in your kernel:
CONFIG_TEST_FIRMWARE=y
CONFIG_FW_LOADER=y
CONFIG_FW_LOADER_USER_HELPER=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
not ok 1 selftests: firmware: fw_run_tests.sh # SKIP
With this fix:
selftests: firmware: fw_run_tests.sh
skip all tests: must be run as root
not ok 1 selftests: firmware: fw_run_tests.sh # SKIP
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Reviwed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
epoll build fails to find pthread lib. Fix Makefile to use LDLIBS
instead of LDFLAGS. LDLIBS is the right flag to use here with -l
option when invoking ld.
gcc -I../../../../../usr/include/ -lpthread epoll_wakeup_test.c -o .../tools/testing/selftests/filesystems/epoll/epoll_wakeup_test
/usr/bin/ld: /tmp/ccaZvJUl.o: in function `kill_timeout':
epoll_wakeup_test.c:(.text+0x4dd): undefined reference to `pthread_kill'
/usr/bin/ld: epoll_wakeup_test.c:(.text+0x4f2): undefined reference to `pthread_kill'
/usr/bin/ld: /tmp/ccaZvJUl.o: in function `epoll9':
epoll_wakeup_test.c:(.text+0x6382): undefined reference to `pthread_create'
/usr/bin/ld: epoll_wakeup_test.c:(.text+0x64d2): undefined reference to `pthread_create'
/usr/bin/ld: epoll_wakeup_test.c:(.text+0x6626): undefined reference to `pthread_join'
/usr/bin/ld: epoll_wakeup_test.c:(.text+0x684c): undefined reference to `pthread_tryjoin_np'
/usr/bin/ld: epoll_wakeup_test.c:(.text+0x6864): undefined reference to `pthread_kill'
/usr/bin/ld: epoll_wakeup_test.c:(.text+0x6878): undefined reference to `pthread_join'
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Commit e61df66c69 ("io-wq: ensure free/busy list browsing see all
items") added a list for io workers in addition to the free and busy
lists, not only making worker walk cleaner, but leaving the busy list
unused. Let's remove it.
Signed-off-by: Hillf Danton <hdanton@sina.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When listing a directory with thounsands of files and most of them are
reparse points, we simply marked all those dentries for revalidation
and then sending additional (compounded) create/getinfo/close requests
for each of them.
Instead, upon receiving a response from an SMB2_QUERY_DIRECTORY
(FileIdFullDirectoryInformation) command, the directory entries that
have a file attribute of FILE_ATTRIBUTE_REPARSE_POINT will contain an
EaSize field with a reparse tag in it, so we parse it and mark the
dentry for revalidation only if it is a DFS or a symlink.
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Clang warns:
../fs/cifs/smb2file.c:70:3: warning: misleading indentation; statement
is not part of the previous 'if' [-Wmisleading-indentation]
if (oparms->tcon->use_resilient) {
^
../fs/cifs/smb2file.c:66:2: note: previous statement is here
if (rc)
^
1 warning generated.
This warning occurs because there is a space after the tab on this line.
Remove it so that the indentation is consistent with the Linux kernel
coding style and clang no longer warns.
Fixes: 592fafe644 ("Add resilienthandles mount parm")
Link: https://github.com/ClangBuiltLinux/linux/issues/826
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
