The lockdep annotation lockdep_assert_softirq_will_run() expects that
either hard or soft interrupts are disabled because both guaranty that
the "raised" soft-interrupts will be processed once the context is left.
This triggers in flush_smp_call_function_from_idle() but it this case it
explicitly calls do_softirq() in case of pending softirqs.
Revert the "softirq will run" annotation in ____napi_schedule() and move
the check back to __netif_rx() as it was. Keep the IRQ-off assert in
____napi_schedule() because this is always required.
Fixes: fbd9a2ceba ("net: Add lockdep asserts to ____napi_schedule().")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Jason A. Donenfeld <Jason@zx2c4.com>
Link: https://lore.kernel.org/r/YjhD3ZKWysyw8rc6@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We'll need an explicitly locked rate node API for netdevsim
to switch eswitch mode setting to locked.
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fib expression stores to a register, so we can't add empty stub.
Check that the register that is being written is in fact redundant.
In most cases, this is expected to cancel tracking as re-use is
unlikely.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
its enough to export the meta get reduce helper and then call it
from nft_meta_bridge too.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Output of expressions might be larger than one single register, this might
clobber existing data. Reset tracking for all destination registers that
required to store the expression output.
This patch adds three new helper functions:
- nft_reg_track_update: cancel previous register tracking and update it.
- nft_reg_track_cancel: cancel any previous register tracking info.
- __nft_reg_track_cancel: cancel only one single register tracking info.
Partial register clobbering detection is also supported by checking the
.num_reg field which describes the number of register that are used.
This patch updates the following expressions:
- meta_bridge
- bitwise
- byteorder
- meta
- payload
to use these helper functions.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Skip register tracking for expressions that perform read-only operations
on the registers. Define and use a cookie pointer NFT_REDUCE_READONLY to
avoid defining stubs for these expressions.
This patch re-enables register tracking which was disabled in ed5f85d422
("netfilter: nf_tables: disable register tracking"). Follow up patches
add remaining register tracking for existing expressions.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The function sets the pernet boolean to avoid the spurious warning from
nf_ct_lookup_helper() when assigning conntrack helpers via nftables.
Fixes: 1a64edf54f ("netfilter: nft_ct: add helper set support")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
ipsec-next
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2022-03-19
1) Delete duplicated functions that calls same xfrm_api_check.
From Leon Romanovsky.
2) Align userland API of the default policy structure to the
internal structures. From Nicolas Dichtel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Luiz Augusto von Dentz says:
====================
bluetooth-next pull request for net-next:
- Add support for Asus TF103C
- Add support for Realtek RTL8852B
- Add support for Realtek RTL8723BE
- Add WBS support to mt7921s
* tag 'for-net-next-2022-03-18' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next: (24 commits)
Bluetooth: ath3k: remove superfluous header files
Bluetooth: bcm203x: remove superfluous header files
Bluetooth: hci_bcm: Add the Asus TF103C to the bcm_broken_irq_dmi_table
Bluetooth: mt7921s: Add WBS support
Bluetooth: mt7921s: Add .btmtk_get_codec_config_data
Bluetooth: mt7921s: Add .get_data_path_id
Bluetooth: mt7921s: Set HCI_QUIRK_VALID_LE_STATES
Bluetooth: btmtksdio: Fix kernel oops in btmtksdio_interrupt
Bluetooth: btmtkuart: fix error handling in mtk_hci_wmt_sync()
Bluetooth: call hci_le_conn_failed with hdev lock in hci_le_conn_failed
Bluetooth: Send AdvMonitor Dev Found for all matched devices
Bluetooth: msft: Clear tracked devices on resume
Bluetooth: fix incorrect nonblock bitmask in bt_sock_wait_ready()
Bluetooth: Don't assign twice the same value
Bluetooth: btrtl: Add support for RTL8852B
Bluetooth: hci_uart: add missing NULL check in h5_enqueue
Bluetooth: Fix use after free in hci_send_acl
Bluetooth: btusb: Use quirk to skip HCI_FLT_CLEAR_ALL on fake CSR controllers
Bluetooth: hci_sync: Add a new quirk to skip HCI_FLT_CLEAR_ALL
Bluetooth: btmtkuart: fix the conflict between mtk and msft vendor event
...
====================
Link: https://lore.kernel.org/r/20220318224752.1477292-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Network drivers can call to netif_get_num_default_rss_queues to get the
default number of receive queues to use. Right now, this default number
is min(8, num_online_cpus()).
Instead, as suggested by Jakub, use the number of physical cores divided
by 2 as a way to avoid wasting CPU resources and to avoid using both CPU
threads, but still allowing to scale for high-end processors with many
cores.
As an exception, select 2 queues for processors with 2 cores, because
otherwise it won't take any advantage of RSS despite being SMP capable.
Tested: Processor Intel Xeon E5-2620 (2 sockets, 6 cores/socket, 2
threads/core). NIC Broadcom NetXtreme II BCM57810 (10GBps). Ran some
tests with `perf stat iperf3 -R`, with parallelisms of 1, 8 and 24,
getting the following results:
- Number of queues: 6 (instead of 8)
- Network throughput: not affected
- CPU usage: utilized 0.05-0.12 CPUs more than before (having 24 CPUs
this is only 0.2-0.5% higher)
- Reduced the number of context switches by 7-50%, being more noticeable
when using a higher number of parallel threads.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Link: https://lore.kernel.org/r/20220315091832.13873-1-ihuguet@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Callers pass msg->msg_flags as flags, which contains MSG_DONTWAIT
instead of O_NONBLOCK.
Signed-off-by: Gavin Li <gavin@matician.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some controllers have problems with being sent a command to clear
all filtering. While the HCI code does not unconditionally
send a clear-all anymore at BR/EDR setup (after the state machine
refactor), there might be more ways of hitting these codepaths
in the future as the kernel develops.
Cc: stable@vger.kernel.org
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Kalle Valo says:
====================
wireless-next patches for v5.18
Third set of patches for v5.18. Smaller set this time, support for
mt7921u and some work on MBSSID support. Also a workaround for rfkill
userspace event.
Major changes:
mac80211
* MBSSID beacon handling in AP mode
rfkill
* make new event layout opt-in to workaround buggy user space
rtlwifi
* support On Networks N150 device id
mt76
* mt7915: MBSSID and 6 GHz band support
* new driver mt7921u
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Again new complaints surfaced that we had broken the ABI here,
although previously all the userspace tools had agreed that it
was their mistake and fixed it. Yet now there are cases (e.g.
RHEL) that want to run old userspace with newer kernels, and
thus are broken.
Since this is a bit of a whack-a-mole thing, change the whole
extensibility scheme of rfkill to no longer just rely on the
message lengths, but instead require userspace to opt in via a
new ioctl to a given maximum event size that it is willing to
understand.
By default, set that to RFKILL_EVENT_SIZE_V1 (8), so that the
behaviour for userspace not calling the ioctl will look as if
it's just running on an older kernel.
Fixes: 14486c8261 ("rfkill: add a reason to the HW rfkill state")
Cc: stable@vger.kernel.org # 5.11+
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220316212749.16491491b270.Ifcb1950998330a596f29a2a162e00b7546a1d6d0@changeid
Saeed Mahameed says:
====================
mlx5-updates-2022-03-17
1) From Maxim Mikityanskiy,
Datapath improvements in preparation for XDP multi buffer
This series contains general improvements for the datapath that are
useful for the upcoming XDP multi buffer support:
a. Non-linear legacy RQ: validate MTU for robustness, build the linear
part of SKB over the first hardware fragment (instead of copying the
packet headers), adjust headroom calculations to allow enabling headroom
in the non-linear mode (useful for XDP multi buffer).
b. XDP: do the XDP program test before function call, optimize
parameters of mlx5e_xdp_handle.
2) From Rongwei Liu, DR, reduce steering memory usage
Currently, mlx5 driver uses mlx5_htbl/chunk/ste to organize
steering logic. However there is a little memory waste.
This update targets to reduce steering memory footprint by:
a. Adjust struct member layout.
b. Remove duplicated indicator by using simple functions call.
With 500k TX rules(3 ste) plus 500k RX rules(6 stes), these patches
can save around 17% memory.
3) Three cleanup commits at the end of this series.
===================
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers might have error messages to propagate to user space, most
common being that they support a single mirror port.
Propagate the netlink extack so that they can inform user space in a
verbal way of their limitations.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Per-flow mirroring with the VCAP IS2 TCAM (in itself handled as an
offload for tc-flower) is done by setting the MIRROR_ENA bit from the
action vector of the filter. The packet is mirrored to the port mask
configured in the ANA:ANA:MIRRORPORTS register (the same port mask as
the destinations for port-based mirroring).
Functionality was tested with:
tc qdisc add dev swp3 clsact
tc filter add dev swp3 ingress protocol ip \
flower skip_sw ip_proto icmp \
action mirred egress mirror dev swp1
and pinging through swp3, while seeing that the ICMP replies are
mirrored towards swp1.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ocelot switches perform port-based ingress mirroring if
ANA:PORT:PORT_CFG field SRC_MIRROR_ENA is set, and egress mirroring if
the port is in ANA:ANA:EMIRRORPORTS.
Both ingress-mirrored and egress-mirrored frames are copied to the port
mask from ANA:ANA:MIRRORPORTS.
So the choice of limiting to a single mirror port via ocelot_mirror_get()
and ocelot_mirror_put() may seem bizarre, but the hardware model doesn't
map very well to the user space model. If the user wants to mirror the
ingress of swp1 towards swp2 and the ingress of swp3 towards swp4, we'd
have to program ANA:ANA:MIRRORPORTS with BIT(2) | BIT(4), and that would
make swp1 be mirrored towards swp4 too, and swp3 towards swp2. But there
are no tc-matchall rules to describe those actions.
Now, we could offload a matchall rule with multiple mirred actions, one
per desired mirror port, and force the user to stick to the multi-action
rule format for subsequent matchall filters. But both DSA and ocelot
have the flow_offload_has_one_action() check for the matchall offload,
plus the fact that it will get cumbersome to cross-check matchall
mirrors with flower mirrors (which will be added in the next patch).
As a result, we limit the configuration to a single mirror port, with
the possibility of lifting the restriction in the future.
Frames injected from the CPU don't get egress-mirrored, since they are
sent with the BYPASS bit in the injection frame header, and this
bypasses the analyzer module (effectively also the mirroring logic).
I don't know what to do/say about this.
Functionality was tested with:
tc qdisc add dev swp3 clsact
tc filter add dev swp3 ingress \
matchall skip_sw \
action mirred egress mirror dev swp1
and pinging through swp3, while seeing that the ICMP replies are
mirrored towards swp1.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the usual trampoline functionality from the generic DSA layer down
to the drivers for MST state changes.
When a state changes to disabled/blocking/listening, make sure to fast
age any dynamic entries in the affected VLANs (those controlled by the
MSTI in question).
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the usual trampoline functionality from the generic DSA layer down
to the drivers for VLAN MSTI migrations.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is useful for switchdev drivers who are offloading MST states
into hardware. As an example, a driver may wish to flush the FDB for a
port when it transitions from forwarding to blocking - which means
that the previous state must be discoverable.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is useful for switchdev drivers that might want to refuse to join
a bridge where MST is enabled, if the hardware can't support it.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
br_mst_get_info answers the question: "On this bridge, which VIDs are
mapped to the given MSTI?"
This is useful in switchdev drivers, which might have to fan-out
operations, relating to an MSTI, per VLAN.
An example: When a port's MST state changes from forwarding to
blocking, a driver may choose to flush the dynamic FDB entries on that
port to get faster reconvergence of the network, but this should only
be done in the VLANs that are managed by the MSTI in question.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Generate a switchdev notification whenever an MST state changes. This
notification is keyed by the VLANs MSTI rather than the VID, since
multiple VLANs may share the same MST instance.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Whenever a VLAN moves to a new MSTI, send a switchdev notification so
that switchdevs can track a bridge's VID to MSTI mappings.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Trigger a switchdev event whenever the bridge's MST mode is
enabled/disabled. This allows constituent ports to either perform any
required hardware config, or refuse the change if it not supported.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make it possible to change the port state in a given MSTI by extending
the bridge port netlink interface (RTM_SETLINK on PF_BRIDGE).The
proposed iproute2 interface would be:
bridge mst set dev <PORT> msti <MSTI> state <STATE>
Current states in all applicable MSTIs can also be dumped via a
corresponding RTM_GETLINK. The proposed iproute interface looks like
this:
$ bridge mst
port msti
vb1 0
state forwarding
100
state disabled
vb2 0
state forwarding
100
state forwarding
The preexisting per-VLAN states are still valid in the MST
mode (although they are read-only), and can be queried as usual if one
is interested in knowing a particular VLAN's state without having to
care about the VID to MSTI mapping (in this example VLAN 20 and 30 are
bound to MSTI 100):
$ bridge -d vlan
port vlan-id
vb1 10
state forwarding mcast_router 1
20
state disabled mcast_router 1
30
state disabled mcast_router 1
40
state forwarding mcast_router 1
vb2 10
state forwarding mcast_router 1
20
state forwarding mcast_router 1
30
state forwarding mcast_router 1
40
state forwarding mcast_router 1
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow a VLAN to move out of the CST (MSTI 0), to an independent tree.
The user manages the VID to MSTI mappings via a global VLAN
setting. The proposed iproute2 interface would be:
bridge vlan global set dev br0 vid <VID> msti <MSTI>
Changing the state in non-zero MSTIs is still not supported, but will
be addressed in upcoming changes.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow the user to switch from the current per-VLAN STP mode to an MST
mode.
Up to this point, per-VLAN STP states where always isolated from each
other. This is in contrast to the MSTP standard (802.1Q-2018, Clause
13.5), where VLANs are grouped into MST instances (MSTIs), and the
state is managed on a per-MSTI level, rather that at the per-VLAN
level.
Perhaps due to the prevalence of the standard, many switching ASICs
are built after the same model. Therefore, add a corresponding MST
mode to the bridge, which we can later add offloading support for in a
straight-forward way.
For now, all VLANs are fixed to MSTI 0, also called the Common
Spanning Tree (CST). That is, all VLANs will follow the port-global
state.
Upcoming changes will make this actually useful by allowing VLANs to
be mapped to arbitrary MSTIs and allow individual MSTI states to be
changed.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull networking fixes from Jakub Kicinski:
"Including fixes from netfilter, ipsec, and wireless.
A few last minute revert / disable and fix patches came down from our
sub-trees. We're not waiting for any fixes at this point.
Current release - regressions:
- Revert "netfilter: nat: force port remap to prevent shadowing
well-known ports", restore working conntrack on asymmetric paths
- Revert "ath10k: drop beacon and probe response which leak from
other channel", restore working AP and mesh mode on QCA9984
- eth: intel: fix hang during reboot/shutdown
Current release - new code bugs:
- netfilter: nf_tables: disable register tracking, it needs more work
to cover all corner cases
Previous releases - regressions:
- ipv6: fix skb_over_panic in __ip6_append_data when (admin-only)
extension headers get specified
- esp6: fix ESP over TCP/UDP, interpret ipv6_skip_exthdr's return
value more selectively
- bnx2x: fix driver load failure when FW not present in initrd
Previous releases - always broken:
- vsock: stop destroying unrelated sockets in nested virtualization
- packet: fix slab-out-of-bounds access in packet_recvmsg()
Misc:
- add Paolo Abeni to networking maintainers!"
* tag 'net-5.17-final' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (26 commits)
iavf: Fix hang during reboot/shutdown
net: mscc: ocelot: fix backwards compatibility with single-chain tc-flower offload
net: bcmgenet: skip invalid partial checksums
bnx2x: fix built-in kernel driver load failure
net: phy: mscc: Add MODULE_FIRMWARE macros
net: dsa: Add missing of_node_put() in dsa_port_parse_of
net: handle ARPHRD_PIMREG in dev_is_mac_header_xmit()
Revert "ath10k: drop beacon and probe response which leak from other channel"
hv_netvsc: Add check for kvmalloc_array
iavf: Fix double free in iavf_reset_task
ice: destroy flow director filter mutex after releasing VSIs
ice: fix NULL pointer dereference in ice_update_vsi_tx_ring_stats()
Add Paolo Abeni to networking maintainers
atm: eni: Add check for dma_map_single
net/packet: fix slab-out-of-bounds access in packet_recvmsg()
net: mdio: mscc-miim: fix duplicate debugfs entry
net: phy: marvell: Fix invalid comparison in the resume and suspend functions
esp6: fix check on ipv6_skip_exthdr's return value
net: dsa: microchip: add spi_device_id tables
netfilter: nf_tables: disable register tracking
...
mlx5_fill_page_array API function is not used.
Remove it, reduce the number of exported functions.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
All WQ types moved to using the fragmented allocation API
for coherent memory. Contiguous API is not used anymore.
Remove it, reduce the number of exported functions.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
This patch adds support for encapsulating IPv4/IPv6 within GENEVE.
In order to use this, a new IFLA_GENEVE_INNER_PROTO_INHERIT flag needs
to be provided at device creation. This property cannot be changed for
the time being.
In case IP traffic is received on a non-tun device the drop count is
increased.
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Link: https://lore.kernel.org/r/20220316061557.431872-1-eyal.birger@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add vlan push_eth and pop_eth action to the hardware intermediate
representation model which would subsequently allow it to be used
by drivers for offload.
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that devlink ports are protected by the instance lock
it seems natural to pass devlink_port as an argument to
the port_split / port_unsplit callbacks.
This should save the drivers from doing a lookup.
In theory drivers may have supported unsplitting ports
which were not registered prior to this change.
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It should be familiar and beneficial to expose devlink instance
lock to the drivers. This way drivers can block devlink from
calling them during critical sections without breakneck locking.
Add port helpers, port splitting callbacks will be the first
target.
Use 'devl_' prefix for "explicitly locked" API. Initial RFC used
'__devlink' but that's too much typing.
devl_lock_is_held() is not defined without lockdep, which is
the same behavior as lockdep_is_held() itself.
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The fundamental premise of VRF and l3mdev core code is binding a socket
to a device (l3mdev or netdev with an L3 domain) to indicate L3 scope.
Legacy code resets flowi_oif to the l3mdev losing any original port
device binding. Ben (among others) has demonstrated use cases where the
original port device binding is important and needs to be retained.
This patch handles that by adding a new entry to the common flow struct
that can indicate the l3mdev index for later rule and table matching
avoiding the need to reset flowi_oif.
In addition to allowing more use cases that require port device binds,
this patch brings a few datapath simplications:
1. l3mdev_fib_rule_match is only called when walking fib rules and
always after l3mdev_update_flow. That allows an optimization to bail
early for non-VRF type uses cases when flowi_l3mdev is not set. Also,
only that index needs to be checked for the FIB table id.
2. l3mdev_update_flow can be called with flowi_oif set to a l3mdev
(e.g., VRF) device. By resetting flowi_oif only for this case the
FLOWI_FLAG_SKIP_NH_OIF flag is not longer needed and can be removed,
removing several checks in the datapath. The flowi_iif path can be
simplified to only be called if the it is not loopback (loopback can
not be assigned to an L3 domain) and the l3mdev index is not already
set.
3. Avoid another device lookup in the output path when the fib lookup
returns a reject failure.
Note: 2 functional tests for local traffic with reject fib rules are
updated to reflect the new direct failure at FIB lookup time for ping
rather than the failure on packet path. The current code fails like this:
HINT: Fails since address on vrf device is out of device scope
COMMAND: ip netns exec ns-A ping -c1 -w1 -I eth1 172.16.3.1
ping: Warning: source address might be selected on device other than: eth1
PING 172.16.3.1 (172.16.3.1) from 172.16.3.1 eth1: 56(84) bytes of data.
--- 172.16.3.1 ping statistics ---
1 packets transmitted, 0 received, 100% packet loss, time 0ms
where the test now directly fails:
HINT: Fails since address on vrf device is out of device scope
COMMAND: ip netns exec ns-A ping -c1 -w1 -I eth1 172.16.3.1
ping: connect: No route to host
Signed-off-by: David Ahern <dsahern@kernel.org>
Tested-by: Ben Greear <greearb@candelatech.com>
Link: https://lore.kernel.org/r/20220314204551.16369-1-dsahern@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net coming late
in the 5.17-rc process:
1) Revert port remap to mitigate shadowing service ports, this is causing
problems in existing setups and this mitigation can be achieved with
explicit ruleset, eg.
... tcp sport < 16386 tcp dport >= 32768 masquerade random
This patches provided a built-in policy similar to the one described above.
2) Disable register tracking infrastructure in nf_tables. Florian reported
two issues:
- Existing expressions with no implemented .reduce interface
that causes data-store on register should cancel the tracking.
- Register clobbering might be possible storing data on registers that
are larger than 32-bits.
This might lead to generating incorrect ruleset bytecode. These two
issues are scheduled to be addressed in the next release cycle.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nf_tables: disable register tracking
Revert "netfilter: conntrack: tag conntracks picked up in local out hook"
Revert "netfilter: nat: force port remap to prevent shadowing well-known ports"
====================
Link: https://lore.kernel.org/r/20220312220315.64531-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Follow the established programming model for this driver and provide
shims in the felix DSA driver which call the implementations from the
ocelot switch lib. The ocelot switchdev driver wasn't integrated with
dcbnl due to lack of hardware availability.
The switch doesn't have any fancy QoS classification enabled by default.
The provided getters will create a default-prio app table entry of 0,
and no dscp entry. However, the getters have been made to actually
retrieve the hardware configuration rather than static values, to be
future proof in case DSA will need this information from more call paths.
For default-prio, there is a single field per port, in ANA_PORT_QOS_CFG,
called QOS_DEFAULT_VAL.
DSCP classification is enabled per-port, again via ANA_PORT_QOS_CFG
(field QOS_DSCP_ENA), and individual DSCP values are configured as
trusted or not through register ANA_DSCP_CFG (replicated 64 times).
An untrusted DSCP value falls back to other QoS classification methods.
If trusted, the selected ANA_DSCP_CFG register also holds the QoS class
in the QOS_DSCP_VAL field.
The hardware also supports DSCP remapping (DSCP value X is translated to
DSCP value Y before the QoS class is determined based on the app table
entry for Y) and DSCP packet rewriting. The dcbnl framework, for being
so flexible in other useless areas, doesn't appear to support this.
So this functionality has been left out.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to the port-based default priority, IEEE 802.1Q-2018 allows the
Application Priority Table to define QoS classes (0 to 7) per IP DSCP
value (0 to 63).
In the absence of an app table entry for a packet with DSCP value X,
QoS classification for that packet falls back to other methods (VLAN PCP
or port-based default). The presence of an app table for DSCP value X
with priority Y makes the hardware classify the packet to QoS class Y.
As opposed to the default-prio where DSA exposes only a "set" in
dsa_switch_ops (because the port-based default is the fallback, it
always exists, either implicitly or explicitly), for DSCP priorities we
expose an "add" and a "del". The addition of a DSCP entry means trusting
that DSCP priority, the deletion means ignoring it.
Drivers that already trust (at least some) DSCP values can describe
their configuration in dsa_switch_ops :: port_get_dscp_prio(), which is
called for each DSCP value from 0 to 63.
Again, there can be more than one dcbnl app table entry for the same
DSCP value, DSA chooses the one with the largest configured priority.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port-based default QoS class is assigned to packets that lack a
VLAN PCP (or the port is configured to not trust the VLAN PCP),
an IP DSCP (or the port is configured to not trust IP DSCP), and packets
on which no tc-skbedit action has matched.
Similar to other drivers, this can be exposed to user space using the
DCB Application Priority Table. IEEE 802.1Q-2018 specifies in Table
D-8 - Sel field values that when the Selector is 1, the Protocol ID
value of 0 denotes the "Default application priority. For use when
application priority is not otherwise specified."
The way in which the dcbnl integration in DSA has been designed has to
do with its requirements. Andrew Lunn explains that SOHO switches are
expected to come with some sort of pre-configured QoS profile, and that
it is desirable for this to come pre-loaded into the DSA slave interfaces'
DCB application priority table.
In the dcbnl design, this is possible because calls to dcb_ieee_setapp()
can be initiated by anyone including being self-initiated by this device
driver.
However, what makes this challenging to implement in DSA is that the DSA
core manages the net_devices (effectively hiding them from drivers),
while drivers manage the hardware. The DSA core has no knowledge of what
individual drivers' QoS policies are. DSA could export to drivers a
wrapper over dcb_ieee_setapp() and these could call that function to
pre-populate the app priority table, however drivers don't have a good
moment in time to do this. The dsa_switch_ops :: setup() method gets
called before the net_devices are created (dsa_slave_create), and so is
dsa_switch_ops :: port_setup(). What remains is dsa_switch_ops ::
port_enable(), but this gets called upon each ndo_open. If we add app
table entries on every open, we'd need to remove them on close, to avoid
duplicate entry errors. But if we delete app priority entries on close,
what we delete may not be the initial, driver pre-populated entries, but
rather user-added entries.
So it is clear that letting drivers choose the timing of the
dcb_ieee_setapp() call is inappropriate. The alternative which was
chosen is to introduce hardware-specific ops in dsa_switch_ops, and
effectively hide dcbnl details from drivers as well. For pre-populating
the application table, dsa_slave_dcbnl_init() will call
ds->ops->port_get_default_prio() which is supposed to read from
hardware. If the operation succeeds, DSA creates a default-prio app
table entry. The method is called as soon as the slave_dev is
registered, but before we release the rtnl_mutex. This is done such that
user space sees the app table entries as soon as it sees the interface
being registered.
The fact that we populate slave_dev->dcbnl_ops with a non-NULL pointer
changes behavior in dcb_doit() from net/dcb/dcbnl.c, which used to
return -EOPNOTSUPP for any dcbnl operation where netdev->dcbnl_ops is
NULL. Because there are still dcbnl-unaware DSA drivers even if they
have dcbnl_ops populated, the way to restore the behavior is to make all
dcbnl_ops return -EOPNOTSUPP on absence of the hardware-specific
dsa_switch_ops method.
The dcbnl framework absurdly allows there to be more than one app table
entry for the same selector and protocol (in other words, more than one
port-based default priority). In the iproute2 dcb program, there is a
"replace" syntactical sugar command which performs an "add" and a "del"
to hide this away. But we choose the largest configured priority when we
call ds->ops->port_set_default_prio(), using __fls(). When there is no
default-prio app table entry left, the port-default priority is restored
to 0.
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20210113154139.1803705-2-olteanv@gmail.com/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
____napi_schedule() needs to be invoked with disabled interrupts due to
__raise_softirq_irqoff (in order not to corrupt the per-CPU list).
____napi_schedule() needs also to be invoked from an interrupt context
so that the raised-softirq is processed while the interrupt context is
left.
Add lockdep asserts for both conditions.
While this is the second time the irq/softirq check is needed, provide a
generic lockdep_assert_softirq_will_run() which is used by both caller.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
ice: GTP support in switchdev
Marcin Szycik says:
Add support for adding GTP-C and GTP-U filters in switchdev mode.
To create a filter for GTP, create a GTP-type netdev with ip tool, enable
hardware offload, add qdisc and add a filter in tc:
ip link add $GTP0 type gtp role <sgsn/ggsn> hsize <hsize>
ethtool -K $PF0 hw-tc-offload on
tc qdisc add dev $GTP0 ingress
tc filter add dev $GTP0 ingress prio 1 flower enc_key_id 1337 \
action mirred egress redirect dev $VF1_PR
By default, a filter for GTP-U will be added. To add a filter for GTP-C,
specify enc_dst_port = 2123, e.g.:
tc filter add dev $GTP0 ingress prio 1 flower enc_key_id 1337 \
enc_dst_port 2123 action mirred egress redirect dev $VF1_PR
Note: outer IPv6 offload is not supported yet.
Note: GTP-U with no payload offload is not supported yet.
ICE COMMS package is required to create a filter as it contains GTP
profiles.
Changes in iproute2 [1] are required to be able to add GTP netdev and use
GTP-specific options (QFI and PDU type).
[1] https://lore.kernel.org/netdev/20220211182902.11542-1-wojciech.drewek@intel.com/T
---
v2: Add more CC
v3: Fix mail thread, sorry for spam
v4: Add GTP echo response in gtp module
v5: Change patch order
v6: Add GTP echo request in gtp module
v7: Fix kernel-docs in ice
v8: Remove handling of GTP Echo Response
v9: Add sending of multicast message on GTP Echo Response, fix GTP-C dummy
packet selection
v10: Rebase, fixed most 80 char line limits
v11: Rebase, collect Harald's Reviewed-by on patch 3
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Before adding yet another possibly contended atomic_long_t,
it is time to add per-cpu storage for existing ones:
dev->tx_dropped, dev->rx_dropped, and dev->rx_nohandler
Because many devices do not have to increment such counters,
allocate the per-cpu storage on demand, so that dev_get_stats()
does not have to spend considerable time folding zero counters.
Note that some drivers have abused these counters which
were supposed to be only used by core networking stack.
v4: should use per_cpu_ptr() in dev_get_stats() (Jakub)
v3: added a READ_ONCE() in netdev_core_stats_alloc() (Paolo)
v2: add a missing include (reported by kernel test robot <lkp@intel.com>)
Change in netdev_core_stats_alloc() (Jakub)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: jeffreyji <jeffreyji@google.com>
Reviewed-by: Brian Vazquez <brianvv@google.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20220311051420.2608812-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
