Fix SD card removal caused by automatic LDO5 power off after boot.
To prevent this, add vqmmc regulator for USDHC, using a GPIO-controlled
regulator that is supplied by LDO5. Since this is implemented on SoM but
used on baseboards with SD-card interface, implement the functionality
on SoM part and optionally enable it on baseboards if needed.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The VAR-SOM-MX8MP integrates a TSC2046 resistive touchscreen controller.
The controller is physically located on the SOM, and its signals are
routed to the SOM pins, allowing carrier boards to make use of it.
This patch adds the TSC2046 node and the appropriate SPI controller.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The VAR-SOM-MX8MP can integrate the WM8904, a high-performance
ultra-low-power stereo codec optimized for portable audio applications.
This patch adds the WM8904 device to the appropriate I2C bus, enables
the SAI peripheral, and introduces the sound node to expose the
sound card to the system.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add device tree nodes for the WiFi and Bluetooth module mounted on the
VAR-SOM-MX8MP. The module can be based on either the NXP IW612 or IW611
chipset, depending on the configuration chosen by the customer.
Regardless of the chipset used, WiFi communicates over SDIO and Bluetooth
over UART.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The VAR-SOM-MX8MP module does not provide an onboard debug console.
UART2 is routed and exposed only on the Symphony carrier board, while
custom carrier designs may choose to expose a different UART.
Move the UART2 node from the SOM device tree to the
imx8mp-var-som-symphony.dts, keeping the SOM dtsi limited to hardware
present on the module itself.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The VAR-SOM-MX8MP module does not include the PCA9534 GPIO expander nor
the LED connected to it. These components are present only on the
Symphony carrier board and may vary across custom carrier designs.
Move the PCA9534 GPIO expander node and the associated LED definition
from the SOM device tree to the Symphony carrier DTS, ensuring the SOM
dtsi describes only hardware present on the module.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The VAR-SOM-MX8MP module does not include a microSD slot connected to
USDHC2. The USDHC2 interface is routed only on the Symphony carrier
board, and it may optionally be used or omitted depending on the
customer's carrier design.
Move the USDHC2 node, its regulators, pinctrl groups and related GPIOs
from the SOM device tree to the Symphony carrier DTS, keeping the SOM
description limited to hardware populated on the module.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The TJA1057 used on i.MX93 EVK is actually high-speed CAN
transceiver, not a regulator supply. So use phys to reflect the truth.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The TJA1048 used on i.MX8MP-EVK is actually high-speed CAN transceiver,
not a regulator supply. So use phys to reflect the truth.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The TJA1051T/3 used on i.MX95-15x15-EVK is actually high-speed CAN
transceiver, not a regulator supply. So use phys to reflect the truth.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the optional LIS2MDL magnetometer on GW71xx baseboards.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As per datasheet of the HDMI protection IC the CEC_IC pin has been
configured as open-drain.
Fixes: ddabb3ce3f ("arm64: dts: freescale: add TQMa8MPQL on MBa8MP-RAS314")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The event out signal on channel 2 is available on pad SAI2_RXD0 which is
connected to X63 pin 13.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As per datasheet of the HDMI protection IC the CEC_IC pin has been
configured as open-drain.
Fixes: 418d1d840e ("arm64: dts: freescale: add initial device tree for TQMa8MPQL with i.MX8MP")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable the hdmi_pai device on the Toradex SMARC iMX8M Plus Development
boards.
The hdmi_pai device, together with aud2htx module, hdmi_pai and hdmi
controller compose the HDMI audio pipeline.
See commit b21f87b832 ("arm64: dts: imx8mp-evk: enable hdmi_pai
device") for the equivalent change on the NXP i.MX8MP EVK board.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable the hdmi_pai device on the various iMX8M Plus Verdin boards that
feature the related HDMI interface.
The hdmi_pai device, together with aud2htx module, hdmi_pai and hdmi
controller compose the HDMI audio pipeline.
See commit b21f87b832 ("arm64: dts: imx8mp-evk: enable hdmi_pai
device") for the equivalent change on the NXP i.MX8MP EVK board.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add alias for the apalis first ethernet interface, this ensures
consistent interface naming (e.g. `end0`) and this is used by the
firmware to correctly set the MAC address.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable the LPSPI6 controller so it can be used by user applications
through the board’s expansion connector.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Symphony carrier board includes a USB Type-C connector on the USB1
port through an NXP PTN5150 Type-C controller connected on the I2C bus.
The PTN5150 provides cable orientation detection and role switching
information to the USB controller.
This patch adds the PTN5150 node, its interrupt line, the required pin
muxing, and wires the controller to the USB1 OTG dual-role device using
the USB role-switch framework.
This patch adds also USB2 support, that remains in host-only mode,
matching the hardware capabilities of the Symphony board.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Symphony carrier board exposes a capacitive touch interface through an
FFC/FPC connector. This interface is wired to an FT5x06 touch controller
on the I2C bus when using Variscite’s 7-inch capacitive touch display.
This patch adds the FT5x06 device node to describe the actual hardware
connection and enables touch functionality on the Symphony board
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch introduces 2 simple aliases:
Add a gpio3->gpio4 alias to allow flexible access to these GPIOs
Add a gpio4 alias for the PCA9534 GPIO expander.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i2c3 of the phyBOARD-Pollux is used on the CSI1 interface to connect
to imaging sensors. Thus define it so it can be easily enabled if
required.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The spi flash on the SoM is missing its vcc supply definition. Add
missing regulator which supplies the flash with 1.8V.
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add PDM micphone sound card support.
This sound card supports recording sound from PDM microphone
and convert the PDM format data to PCM data.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Refine label with "wm8962" and node name with "codec" to follow
devicetree specification.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
CAN1 and Micfil share pins on imx93-9x9-qsb board, use TMUX1574RSVR
to control the connection: put sel to high, select CAN1, put sel to
low, select Micfil. In default, sel keep low.
To support CAN1, need to put the sel to high. Besides, CAN1 use phy
TJA1057GT/3.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
DRAM1 is only 2GiB in size (0x00_8000_0000 - 0x01_0000_0000) which is
already used by Linux kernel, etc. Move the allocation area of BMAN and
QMAN to DRAM1 region. This frees the complete DRAM2 area for e.g. CMA.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add bt-sco sound card, which is used by BT HFP case.
It supports wb profile as default.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add 'thermal_zones' as a label to the thermal-zones node.
Without this label, it is not possible to add additional
trip points in board files. For example, to add an active
trip point for controlling a fan.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The FRDM-i.MX8MP is an NXP development platform based on the i.MX8M Plus
SoC, featuring a quad Cortex-A53, Cortex-M7 co-processor, 4GB LPDDR4,
32GB eMMC, Wi-Fi 6/Bluetooth 5.4/802.15.4 tri-radio, Ethernet, HDMI/MIPI
display interfaces, camera connectors, and standard expansion headers.
Based on the device tree found in the NXP repository at github
https://github.com/nxp-imx-support/meta-imx-frdm and on imx8mp-evk
board kernel mainline device tree.
This is a basic device tree supporting:
- Quad Cortex-A53
- 4GB LPDDR4 DRAM
- PCA9450C PMIC with regulators
- Two NXP PCAL6416 GPIO expanders
- RGB LEDs via GPIO expander
- I2C1, I2C2, I2C3 controllers
- UART2 (console) and UART3 (with RTS/CTS)
- USDHC3 (8-bit eMMC)
- SNVS power key (onboard power button)
Co-developed-by: Xiaofeng Wei <xiaofeng.wei@nxp.com>
Signed-off-by: Xiaofeng Wei <xiaofeng.wei@nxp.com>
Signed-off-by: Rogerio Pimentel <rpimentel.silva@gmail.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Replace the 0 with IMX_LPCG_CLK_0 for LPCG clock indices. Although the
numerical value is identical, the LPCG input is defined as
IMX_LPCG_CLK_<n>, so using the symbolic constant improves clarity and
consistency with the LPCG clock naming convention.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Replace the 0 with IMX_LPCG_CLK_0 for LPCG clock indices. Although the
numerical value is identical, the LPCG input is defined as
IMX_LPCG_CLK_<n>, so using the symbolic constant improves clarity and
consistency with the LPCG clock naming convention.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
