Loongson display controller IP has been integrated in both Loongson north
bridge chipset (ls7a1000/ls7a2000) and Loongson SoCs (ls2k1000/ls2k2000).
It has even been included in Loongson's BMC products. It has two display
pipes, and each display pipe supports a primary plane and a cursor plane.
For the DC in the LS7a1000, each display pipe has a DVO output interface,
which is able to support 1920x1080@60Hz. For the DC in the LS7A2000, each
display pipe is equipped with a built-in HDMI encoder, which is compliant
with the HDMI 1.4 specification. The first display pipe is also equipped
with a transparent VGA encoder, which is parallel with the HDMI encoder.
To get a decent performance for writing framebuffer data to the VRAM, the
write combine support should be enabled.
v1 -> v2:
1) Use hpd status reg when polling for ls7a2000.
2) Fix all warnings that emerged when compiling with W=1.
v2 -> v3:
1) Add COMPILE_TEST to Kconfig and make the driver off by default
2) Alphabetical sorting headers (Thomas)
3) Untangle register access functions as much as possible (Thomas)
4) Switch to TTM-based memory manager (Thomas)
5) Add the chip ID detection function which can be used to distinguish
chip models
6) Revise the built-in HDMI phy driver, nearly all main stream mode below
4K@30Hz is tested, and this driver supports clone(mirror) display mode
and extend(joint) display mode.
v3 -> v4:
1) Quickly fix a small mistake.
v4 -> v5:
1) Add per display pipe debugfs support to the builtin HDMI encoder.
v5 -> v6:
1) Remove stray code which didn't get used, say lsdc_of_get_reserved_ram
2) Fix all typos I could found, make sentences and code more readable
3) Untangle lsdc_hdmi*_connector_detect() function according to the pipe
4) Rename this driver as loongson.
v6 -> v7:
1) Add prime support for buffer self-sharing, sharing buffer with
drm/etnaviv is also tested and it works with limitations.
2) Implement buffer object tracking with list_head.
3) Add S3(sleep to RAM) support
4) Rewrite lsdc_bo_move since TTM core stop allocating resources
during BO creation. Patch V1 ~ V6 of this series no longer work.
Thus, we send V7.
v7 -> v8:
1) Zero a compile warning on a 32-bit platform, compile with W=1
2) Revise lsdc_bo_gpu_offset() and make minor cleanups.
3) Pageflip tested on the virtual terminal with the following commands:
modetest -M loongson -s 32:1920x1080 -v
modetest -M loongson -s 34:1920x1080 -v -F tiles
It works like a charm, when running the pageflip test with dual screens
configuration, another two additional BOs were created by the modetest,
VRAM usage up to 40+ MB, well we have at least 64MB, still enough.
# cat bos
bo[0000]: size: 8112kB VRAM
bo[0001]: size: 16kB VRAM
bo[0002]: size: 16kB VRAM
bo[0003]: size: 16208kB VRAM
bo[0004]: size: 8112kB VRAM
bo[0005]: size: 8112kB VRAM
v8 -> v9:
1) Select I2C and I2C_ALGOBIT in Kconfig, should depend on MMU.
2) Using pci_get_domain_bus_and_slot to get the GPU device.
v9 -> v10:
1) Revise lsdc_drm_freeze() to implement S3 correctly. We realized that
the pinned BO could not be moved, the VRAM lost power when sleeping
to RAM. Thus, the data in the buffer who is pinned in VRAM will get
lost when resumed. Yet it's not a big problem because this driver
relies on the CPU to update the front framebuffer. We can see the
garbage data when resume from S3, but the screen will show the right
image as I move the cursor. This is due to the CPU repaint. v10 of
this patch makes S3 perfect by unpin all of the BOs in VRAM, evict
them all to system RAM in lsdc_drm_freeze().
v10 -> v11:
1) On a double-screen case, The buffer object backing the single giant
framebuffer is referenced by two GEM objects; hence, it will be
pinned at least twice by prepare_fb() function. This causes its pin
count > 1. V10 of this patch only unpins VRAM BOs once when suspend,
which is not correct on double-screen case. V11 of this patch unpin
the BOs until its pin count reaches zero when suspend. Then, we make
the S3 support complete finally. With v11, I can't see any garbage
data when resume.
2) Fix vblank wait timeout when disable CRTC.
3) Test against IGT, at least fbdev test and kms_flip test passed.
4) Rewrite pixel PLL update function, magic numbers eliminated (Emil)
5) Drop a few common hardware features description in lsdc_desc (Emil)
6) Drop lsdc_mode_config_mode_valid(), instead add restrictions in dumb
create function. (Emil)
7) Untangle the ls7a1000 case and ls7a2000 case completely (Thomas)
v11 -> v12:
none
v12 -> v13:
1) Add benchmarks to figure out the bandwidth of the hardware platform.
Usage:
# cd /sys/kernel/debug/dri/0/
# cat benchmark
2) VRAM is filled with garbage data if uninitialized, add a buffer
clearing procedure (lsdc_bo_clear), clear the BO on creation time.
3) Update copyrights and adjust coding style (Huacai)
v13 -> v14:
1) Trying to add async update support for cursor plane.
v14 -> v15:
1) Add lsdc_vga_set_decode() funciton, which allow us remove multi-video
cards workaround, now it allow drm/loongson, drm/amdgpu, drm/etnaviv
co-exist in the system, more is also possible (Emil and Xuerui)
2) Fix typos and grammar mistakes as much as possible (Xuerui)
3) Unify copyrights as GPL-2.0+ (Xuerui)
4) Fix a bug introduce since V13, TTM may import BO from other drivers,
we shouldn't clear it on such a case.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: David Airlie <airlied@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: loongson-kernel@lists.loongnix.cn
Tested-by: Liu Peibao <liupeibao@loongson.cn>
Tested-by: Li Yi <liyi@loongson.cn>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Sui Jingfeng <suijingfeng@loongson.cn>
Link: https://patchwork.freedesktop.org/patch/msgid/20230615143613.1236245-2-15330273260@189.cn
Wait until the command transfer FIFO is empty before loading in the next
command. The previous behavior where the code waited until command transfer
FIFO was not full suffered from transfer corruption, where the last command
in the FIFO could be overwritten in case the FIFO indicates not full, but
also does not have enough space to store another transfer yet.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # imx8mm-icore
Link: https://patchwork.freedesktop.org/patch/msgid/20230615201511.565923-1-marex@denx.de
@codeaurora.org email addresses are no longer valid and will bounce.
I reached out to Liam about updating his entry under DMA-BUF HEAPS
FRAMEWORK with an @codeaurora.org address. His response:
"I am not a maintainer anymore, that should be removed."
Liam currently does not have an email address that can be used to remove
this entry, so I offered to submit a cleanup on his behalf with Liam's
consent.
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Acked-by: John Stultz <jstultz@google.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230628180534.31819-1-quic_jhugo@quicinc.com
ASpeed distinguishes among various generations of the AST graphics
chipset with various models. [1] The most-recent model AST 2600 is
of the 7th generation, the AST 2500 is of the 6th generation, and so
on.
The ast driver simply picks one of the models as representative for
the whole generation. In several places, individual models of the
same generation need to be handled differently, which then requires
additional code for detecting the model.
Introduce different generations of the Aspeed chipset. In the source
code, refer to the generation instead of the representation model where
possible. The few places that require per-model handling are now clearly
marked.
In the enum ast_chip, we arrange each model's value such that it
encodes the generation. This allows for an easy test. The actual values
are ordered, but not of interest to the driver.
v2:
* use __ast_gen_is_eq() (Jingfeng)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://web.archive.org/web/20141007093258/http://www.aspeedtech.com/products.php?fPath=20 # 1
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Tested-by: Jocelyn Falempe <jfalempe@redhat.com> # AST2600
Reviewed-by: Sui Jingfeng <suijingfeng@loongson.cn>
Link: https://patchwork.freedesktop.org/patch/msgid/20230621130032.3568-10-tzimmermann@suse.de
Add Kconfig option CONFIG_FB_DEVICE and make the virtual fbdev
device optional. If the new option has not been selected, fbdev
does not create files in devfs, sysfs or procfs.
Most modern Linux systems run a DRM-based graphics stack that uses
the kernel's framebuffer console, but has otherwise deprecated fbdev
support. Yet fbdev userspace interfaces are still present.
The option makes it possible to use the fbdev subsystem as console
implementation without support for userspace. This closes potential
entry points to manipulate kernel or I/O memory via framebuffers. It
also prevents the execution of driver code via ioctl or sysfs, both
of which might allow malicious software to exploit bugs in the fbdev
code.
A small number of fbdev drivers require struct fbinfo.dev to be
initialized, usually for the support of sysfs interface. Make these
drivers depend on FB_DEVICE. They can later be fixed if necessary.
v3:
* effect -> affect in Kconfig help (Daniel)
v2:
* set FB_DEVICE default to y (Geert)
* comment on {get,put}_device() (Sam)
* Kconfig fixes (Sam)
* add TODO item about FB_DEVICE dependencies (Sam)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230613110953.24176-39-tzimmermann@suse.de
Move fbdev's procfs code into a separate file and contain it in
init and cleanup helpers. For the cleanup, replace remove_proc_entry()
with proc_remove(). It is equivalent in functionality, but looks
more like an inverse of proc_create_seq().
v2:
* document proc_remove() usage (Sam)
* revert unrelated removal of for_each_registered_fb()
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230613110953.24176-36-tzimmermann@suse.de
Move the logic to create and destroy fbdev devices into the new
helpers fb_device_create() and fb_device_destroy().
There was a call to fb_cleanup_device() in do_unregister_framebuffer()
that was too late. The device had already been removed at this point.
Move the call into fb_device_destroy().
Declare the helpers in the new internal header file fb_internal.h, as
they are only used within the fbdev core module.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230613110953.24176-35-tzimmermann@suse.de
