RX DCK stands for receiver DC calibration. With this calibration, we have
proper DC offset to reflect correct received signal strength indicator.
Do this calibration when bringing up interface and going to connect.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240627025849.25198-3-pkshih@realtek.com
IQ signal calibration is a very important calibration to yield good RF
performance. We do this calibration once we are going to an AP. During
scanning phase, without this calibration RF performance is still
acceptable because it transmits and receives with low data rate at
this phase.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240627025849.25198-2-pkshih@realtek.com
Calculate a TX power constraint based on content of ieee80211 Transmit
Power Envelope (TPE). Since HW control registers aren't designed as many
as all kinds of TPE fields, we strictly intersect all TPE inputs in driver.
Then, according to result, constrain TX power via TX power limit/limit_RU.
Besides, extend dbgfs txpwr_table to show info about 6 GHz regulatory.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240626023237.7901-1-pkshih@realtek.com
TX power index is read from the efuse on init, the values get written to
the TX power registers when the channel gets switched.
When the chip has not yet been calibrated, the efuse values are 0xFF,
which on some boards leads to USB timeouts for reading/writing registers
after the first frames have been sent.
The vendor driver (v5.11.5-1) checks for these invalid values and sets
default values instead. Implement something similar in
rtl8188fu_parse_efuse().
Fixes: c888183b21 ("wifi: rtl8xxxu: Support new chip RTL8188FU")
Signed-off-by: Martin Kaistra <martin.kaistra@linutronix.de>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240624140037.231657-1-martin.kaistra@linutronix.de
DPK is short for digital pre-distortion calibration. It can adjusts digital
waveform according to PA linear characteristics dynamically to enhance
TX EVM for high power.
Do this calibration when we are going to run on AP channel. To prevent
power offset out of boundary, it monitors thermal and set proper boundary
to register.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240621073458.55187-3-pkshih@realtek.com
TSSI is transmitter signal strength indication, which is a close-loop
hardware circuit to feedback actual transmitting power as a reference for
next transmission.
It does full calibration when we are going to connect an AP. When switching
bands or channels for scanning or some reasons, reset hardware status to
prevent use wrong power value feedback from previous transmission.
It also loads tables of compensation values reflecting current temperature
into registers according to channel and band group to transmit packets
with expected power.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240621073458.55187-2-pkshih@realtek.com
We add polling after sending LPS H2C to ensure that the Firmware is
received and executes RPWM thereafter. Otherwise, if the Firmware
executes RPWM without receiving LPS H2C, it will cause beacon loss in
WoWLAN mode due to the inability to obtain channel and bandwidth
information from H2C.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240620055825.17592-8-pkshih@realtek.com
While downloading Firmware in the resume flow, it is possible to receive
beacon and send H2C to Firmware. However, if Firmware receives unexpected
H2C during the download process, it will fail. Therefore, we prevent to
send unexpected H2C during download Firmware in WoWLAN mode.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240620055825.17592-6-pkshih@realtek.com
Currently the number of frames sent to the chip in a single USB Request
Block is limited only by the size of the TX buffer, which is 20 KiB.
Testing reveals that as many as 13 frames get aggregated. This is more
than what any of the chips would like to receive. RTL8822CU, RTL8822BU,
and RTL8821CU want at most 3 frames, and RTL8723DU wants only 1 frame
per URB.
RTL8723DU in particular reliably malfunctions during a speed test if it
receives more than 1 frame per URB. All traffic seems to stop. Pinging
the AP no longer works.
Fix this problem by limiting the number of frames sent to the chip in a
single URB according to what each chip likes.
Also configure RTL8822CU, RTL8822BU, and RTL8821CU to expect 3 frames
per URB.
RTL8703B may or may not be found in USB devices. Declare that it wants
only 1 frame per URB, just in case.
Tested with RTL8723DU and RTL8811CU.
Cc: stable@vger.kernel.org
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/cb46ea35-7e59-4742-9c1f-01ceeaad36fb@gmail.com
Read 32 bits RX info to a local variable to fix race condition between
reading RX length and RX tag.
Another solution is to get RX tag at first statement, but adopted solution
can save some memory read, and also save 15 bytes binary code.
RX tag, a sequence number, is used to ensure that RX data has been DMA to
memory completely, so driver must check sequence number is expected before
reading other data.
This potential problem happens only after enabling 36-bit DMA.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240611021901.26394-2-pkshih@realtek.com
Modern platforms can install more than 4GB memory, so DMA address can
larger than 32 bits. If a platform doesn't enable IOMMU, kernel needs extra
works of swiotlb to help DMA that packets reside on memory over 4GB.
The DMA addressing capability of Realtek WiFi chips is 36 bits, so set
LSB 4 bits of high 32-bit address to register and TX/RX descriptor, which
below figure shows 3-level pointers in TX direction, and RX direction is
similar but 2-level pointers only.
+--------+
| | register to head of TX BD
+---|----+
| +---------+
+-----> | TX BD | (in memory)
+----|----+
| +---------+
+------> | TX WD | (in memory)
+----|----+
| +--------+
+------> | skb |
+--------+
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240611021901.26394-1-pkshih@realtek.com
Version C of 8922AE hardware will use the same firmware of version B, so
extend rule of firmware recognition to allow less but closest firmware
version. Originally only accept firmware with matched version.
Tested on version A/B/C of 8922AE.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240607140251.8295-1-pkshih@realtek.com
The channel configuration of 8852BT is very similar but a little different
to 8852B, so use chip ID as condition to add extra handles including
external loss compensation, ADC configurations, spur settings and so on.
Don't affect existing 8852BE.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240607070659.80263-3-pkshih@realtek.com
New upcoming chip is RTL8852BE-VT (or RTL8852BTE; 8852BT PCIE interface),
which is a variant of 8852B, and many codes excepting to RF calibration
can be shared, so move common code to an new kernel module named
rtw89_8852b_common.ko.
No logic change.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240607070659.80263-2-pkshih@realtek.com
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240603091541.8367-7-wsa+renesas@sang-engineering.com
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_interruptible_timeout() causing patterns like:
timeout = wait_for_completion_interruptible_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Fix to the proper variable type 'long' while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240603091541.8367-5-wsa+renesas@sang-engineering.com
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240603091541.8367-4-wsa+renesas@sang-engineering.com
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_event_timeout() causing patterns like:
timeout = wait_event_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Fix to the proper variable type 'long' while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240603091541.8367-3-wsa+renesas@sang-engineering.com
This is an effort to get rid of all multiplications from allocation
functions in order to prevent integer overflows [1][2].
As the "cmd_buf" variable is a pointer to "struct at76_command" and
this structure ends in a flexible array:
struct at76_command {
[...]
u8 data[];
} __packed;
the preferred way in the kernel is to use the struct_size() helper to
do the arithmetic instead of the calculation "size + count" in the
kmalloc() function.
Also, declare a new variable (total_size) since the return value of the
struct_size() helper is used several times.
At the same time, prepare for the coming implementation by GCC and Clang
of the __counted_by attribute. Flexible array members annotated with
__counted_by can have their accesses bounds-checked at run-time via
CONFIG_UBSAN_BOUNDS (for array indexing) and CONFIG_FORTIFY_SOURCE (for
strcpy/memcpy-family functions). In this case, it is important to note
that the attribute used is "__counted_by_le" since the counter type is
"__le16".
This way, the code is more readable and safer.
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#open-coded-arithmetic-in-allocator-arguments [1]
Link: https://github.com/KSPP/linux/issues/160 [2]
Signed-off-by: Erick Archer <erick.archer@outlook.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/AS8PR02MB7237578654CEDDFE5F8C17BA8BFE2@AS8PR02MB7237.eurprd02.prod.outlook.com
When EMLSR gets unblocked, the current code checks if the last exit was
due to an EXIT reason (as opposed to a BLOCKING one), and if so, it
does nothing, as in this case a MLO scan was scheduled to run in 30
seconds.
But the code doesn't consider the time that passed from the last exit,
so if immediately after the exit a blocker occurred (e.g. non-BSS
interface), and lasts for more than 30 seconds, then the MLO scan and the
following link selection will decide not to enter EMLSR, and when the
unblocking event finally happens, the reason is still set to the EXIT one,
so it will do nothing, and we will not have the chance to re-enable EMLSR.
Fix this by checking also the time that has passed since the last exit,
only if it is less than 30 seconds, we can count on the scheduled MLO
scan.
Note that clearing the reason itself can't be done since it is needed
for the EMLSR prevention mechanism.
Fixes: 2f33561ea8 ("wifi: iwlwifi: mvm: trigger link selection after exiting EMLSR")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240605140327.58556fc4cfa9.I4c55b3cd9f20b21b37f28258d0fb6842ba413966@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The TX queue code was mostly moved out to support an internal
transport that we were never going to publish, but we're no
longer using that. Since we're also going to be dissolving
the virtual transport layer entirely, integrate the TX queue
code into the PCIe layer.
This also has a small kernel of already removing the virtual
transport function layer, since iwl_trans_send_cmd() calls
iwl_trans_pcie_send_hcmd() directly now, even if that still
calls the transport send_cmd method for now, we'll clean it
up later.
Also, not everything is renamed yet.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240605140327.936b13f45071.Ib219ce01a1e67bcad79d5131626db950252aaa46@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When e.g. wpa_supplicant sets only the MLD "sta" authorized
state, the code actually applies that change, but then returns
an error to userspace anyway because there were no changes to
the link station, and no link ID was given. However, it's not
incorrect to not have a link ID when wanting to change only
the MLD peer ("sta") state, so the code shouldn't require it.
To fix this, separate the "new_link" argument out into a new
three-state enum, because if modify is called on a link STA
only, it should return an error if no link is given or if it
doesn't exist. For modify on the MLD "sta", not having a link
ID is OK, but if there is one it should be validated.
This seems to not have mattered much as wpa_supplicant just
prints a message and continues, and the authorized state was
already set before this error return. However, in the later
code powersave recalculation etc. will be skipped, so that it
may result in never allowing powersave on MLO connections.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240605135233.48e2b8af07e3.Ib9793c383fcba118c05100e024f4a11a1c3d0e85@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
