ADV7610 is another HDMI receiver chip, very similar to
the ADV7611.
Also: print chip names in upper case.
Fix an error message claiming that no ADV761x has been found,
while in reality a chip different than requested (though still
supported) may have been found.
Tested on TinyRex BaseBoard Lite.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
ADV7610 is another HDMI receiver chip, very similar to
the ADV7611. Tested on TinyRex BaseBoard Lite.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The TDA1997x (HDMI receiver) driver currently uses a specific video
format detection scheme. The frame (or field in interlaced mode), line
and HSync pulse durations are compared to those of known, standard video
modes. If a match is found, the mode is assumed to be detected,
otherwise -ERANGE is returned (then possibly ignored). This means that:
- another mode with similar timings will be detected incorrectly
(e.g. 2x faster clock and lines twice as long)
- non-standard modes will not work.
This patch replaces this scheme with a direct read of geometry
registers. This way all modes recognized by the chip are supported.
In interlaced modes, the code assumes the V sync signal has the same
duration for both fields. While this may be not necessarily true,
I can't see any way to get the "other" V sync width. This is most
probably harmless.
All tests have been performed on Gateworks' Ventana GW54xx board, with
a TDA19971 chip.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Newer clang versions are suspicious of definitions that mix concatenated
strings with comma-separated arrays of strings, this has found real bugs
elsewhere, but this seems to be a false positive:
drivers/media/usb/gspca/gl860/gl860-mi1320.c:62:37: error: suspicious concatenation of string literals in an array initialization; did you
mean to separate the elements with a comma? [-Werror,-Wstring-concatenation]
"\xd3\x02\xd4\x28\xd5\x01\xd0\x02" "\xd1\x18\xd2\xc1"
^
,
drivers/media/usb/gspca/gl860/gl860-mi1320.c:62:2: note: place parentheses around the string literal to silence warning
"\xd3\x02\xd4\x28\xd5\x01\xd0\x02" "\xd1\x18\xd2\xc1"
Replace the string literals by compound initializers, using normal hex numbers.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Similar configuration to Kworld PC150-U.
Tested: Composite, S-Video, NTSC, ATSC
Unsupported: IR remote
Signed-off-by: Scott K Logan <logans@cottsay.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
I came across a link failure from randconfig builds:
x86_64-linux-ld: drivers/media/i2c/ths8200.o: in function `ths8200_remove':
ths8200.c:(.text+0x491): undefined reference to `v4l2_async_unregister_subdev'
x86_64-linux-ld: drivers/media/i2c/ths8200.o: in function `ths8200_probe':
ths8200.c:(.text+0xe49): undefined reference to `v4l2_async_register_subdev'
x86_64-linux-ld: drivers/media/i2c/tw9910.o: in function `tw9910_remove':
tw9910.c:(.text+0x467): undefined reference to `v4l2_async_unregister_subdev'
x86_64-linux-ld: drivers/media/i2c/tw9910.o: in function `tw9910_probe':
tw9910.c:(.text+0x1123): undefined reference to `v4l2_async_register_subdev'
These clearly lack a 'select' statement, but I don't know why
this started happening only now. I had a bit of a look around to find
other configs that have the same problem, but could not come up with
a reliable way and found nothing else through experimentation.
It is likely that other symbols like these exist that need an extra
select.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Adding kfree(dvb) to vidtv_bridge_remove() will remove the memory
too soon: if an application still has an open filehandle to the device
when the driver is unloaded, then when that filehandle is closed, a
use-after-free access takes place to the freed memory.
Move the kfree(dvb) to vidtv_bridge_dev_release() instead.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 76e21bb8be ("media: vidtv: Fix memory leak in remove")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If v4l2_ctrl_new_custom fails in cedrus_init_ctrls the error path will
free ctx->ctrls, which is also freed in cedrus release. Fix this by
setting ctx->ctrls to NULL instead of inadvertently removing kfree
calls.
Signed-off-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
I have not been able to give dvb the attention it needs, and now I have
even less time. Of course I will continue to maintain rc-core (infrared).
Unfortunately this means that dvb will have maintainance issues.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
After freed the dev->urb_list, we should set it to NULL as well as set
counter to zero.
Requested-by: Sean Young <sean@mess.org>
Signed-off-by: Nil Yi <teroincn@163.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
mn88443x_cmn_power_on() did not handle possible errors of
clk_prepare_enable() and always finished successfully so that its caller
mn88443x_probe() did not care about failed preparing/enabling of clocks
as well.
Add missed error handling in both mn88443x_cmn_power_on() and
mn88443x_probe(). This required to change the return value of the former
from "void" to "int".
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 0f408ce894 ("media: dvb-frontends: add Socionext MN88443x ISDB-S/T demodulator driver")
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Co-developed-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Signed-off-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Don't populate the read-only arrays on the stack but instead them
static const. Also makes the object code smaller by 154 bytes:
Before:
text data bss dec hex filename
42949 22424 0 65373 ff5d media/dvb-frontends/mb86a20s.o
After:
text data bss dec hex filename
42731 22488 0 65219 fec3 media/dvb-frontends/mb86a20s.o
(gcc version 11.2.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use v4l2 control API helpers to support the events.
Fixes v4l2-compliance:
test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: FAIL
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use v4l2 control API helpers to support the events.
Fixes v4l2-compliance:
test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: FAIL
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use v4l2 control API helpers to support the events.
Fixes v4l2-compliance:
test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: FAIL
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
bus_info field had a different value for the media entity and the video
device.
Fixes v4l2-compliance:
v4l2-compliance.cpp(637): media bus_info 'PCI:0000:00:05.0' differs from
V4L2 bus_info 'PCI:viewfinder'
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
For a try_fmt call, the node noes not need to be enabled.
Fixes v4l2-compliance
fail: v4l2-test-formats.cpp(717): Video Output Multiplanar is valid, but
no TRY_FMT was implemented
test VIDIOC_TRY_FMT: FAIL
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The initial format did not have a valid size.
Fixes v4l2-compliance:
fail: v4l2-test-formats.cpp(723): Video Output Multiplanar:
TRY_FMT(G_FMT) != G_FMT
test VIDIOC_TRY_FMT: FAIL
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If num_planes is different than zero num_planes and sizes must be
checked to support the format.
Fix the following v4l2-compliance error:
Buffer ioctls (Input 0):
fail: v4l2-test-buffers.cpp(717): q.create_bufs(node, 1, &fmt) != EINVAL
test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: FAIL
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a V4L2 driver for Renesas R-Car Image Signal Processor. The driver
supports the R-Car V3U SoC where the ISP IP sits between the R-Car CSI-2
receiver and VIN and filters the CSI-2 data based on VC/DT and directs
the video stream to different VIN IPs.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The only usage of imgu_subdev_internal_ops is to assign its address to
the internal_ops field in the v4l2_subdev struct, which is a pointer to
const v4l2_subdev_internal_ops. Make it const to allow the compiler to
put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add MIPI CCS compliant devices, a few Sony IMX, Hynix Hi-846 and
Omnivision ov13b10 sensors and the DW9768 lens driver to the list of
supported devices. Also drop SMIA since as a standard it is obsolete.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The SK Hynix Hi-846 is a 1/4" 8M Pixel CMOS Image Sensor. It supports
usual features like I2C control, CSI-2 for frame data, digital/analog
gain control or test patterns.
This driver supports the 640x480, 1280x720 and 1632x1224 resolution
modes. It supports runtime PM in order not to draw any unnecessary power.
The part is also called YACG4D0C9SHC and a datasheet can be found at
https://product.skhynix.com/products/cis/cis.go
The large sets of partly undocumented register values are for example
found when searching for the hi846_mipi_raw_Sensor.c Android driver.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The sensor orientation is read from the _PLC ACPI buffer and converted to a v4l2
format.
The sensor rotation is read from the SSDB ACPI buffer and converted into
degrees.
Signed-off-by: Fabian Wüthrich <me@fabwu.ch>
Reviewed-by: Daniel Scally <djrscally@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
- Get the min buffer count required by FW from source event change
and use the same value to decide actual buffer count and for
buffer size calculation.
- Setup DPB and OPB buffers after session continue incase of
reconfig.
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In existing video driver implementation vpp frequency calculation in
calculate_inst_freq() is always zero because the value of vpp_freq_per_mb
is always zero for decoder.
Fixed this by correcting the calculating the vpp frequency calculation for
decoder.
Fixes: 3cfe5815ce ("media: venus: Enable low power setting for encoder")
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Video driver maintains an internal context for the output buffer size.
During S_fmt() on capture plane, the output buffer size is not updated
in driver context. As a result, during buf_prepare(), the size of the
vb2_plane and internal size of the buffer, as maintained by the driver,
does not match. This leads to buf_prepare() failure.
Update the instance context for the output buffer size during s_fmt().
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In current video driver implementation in calculate_inst_freq()
frequency is calculated based on filled_len. The filled_len may
vary frame to frame, because of this in load_scale_v4() since
frequency is calculated for all instances, driver is throwing
false warning like "HW is overloaded".
Hence to handle this, changed log level to low log message. Since the
actual session rejection is happening in decide_core() based on
load.
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
gcc notices that the driver mixes 'dma_addr_t' 'u8 *' and 'u32'
to store DMA addresses:
drivers/media/platform/omap/omap_vout.c: In function 'omap_vout_vb2_prepare':
drivers/media/platform/omap/omap_vout.c:979:37: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
vout->queued_buf_addr[vb->index] = (u8 *)buf_phy_addr;
^
drivers/media/platform/omap/omap_vout.c: In function 'omap_vout_create_video_devices':
drivers/media/platform/omap/omap_vout.c:1479:21: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
vout->fbuf.base = (void *)info.paddr;
Use dma_addr_t everywhere here to avoid the type conversions and document
what the address is used for. Assigning to vout->fbuf.base still requires
a cast, since that is part of the driver independent data structure.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Remove soft reset between frames, which was merely a workaround,
actually replace it with something less aggressive: clearing of jpeg stream
buffer pointer, via STM_CTRL[BITBUF_PTR_CLR].
According to the reference manual, the BITBUF_PTR_CLR is performed on
context switch, but, per hardware team recommendation, it is also working
without context switch, which is the case for this driver, for now.
Without soft reset and without BITBUF_PTR_CLR, successive encoding jobs
continue from where the previous left off, basically writing past the
v4l2 buffer.
Signed-off-by: Mirela Rabulea <mirela.rabulea@nxp.com>
Reviewed-by: Robert Chiras <robert.chiras@nxp.com>
Reviewed-by: Laurentiu Palcu <laurentiu.palcu@oss.nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add some body to the dummy jpeg used to inject a default DHT.
Use jpeg_image_red as compressed image data, insert it at the
end of SOS, before EOI.
The pure dummy jpeg was occasionally not working well on
8qxp C0.
Signed-off-by: Mirela Rabulea <mirela.rabulea@nxp.com>
Reviewed-by: Laurentiu Palcu <laurentiu.palcu@oss.nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
