Samsung pinctrl drivers changes for v4.18
1. Driver expects specific order of GPIO interrupt banks. For S5Pv220
and Exynos5410 this order was not preserved so fix and document it.
2. Remove support for Exynos5440 (tree-wide, support is dropped because
there are no real users of this platform, it also did not get testing
since long time).
3. Fix lost state of GPF1..5 pins on Exynos5433 during system suspend.
GPF1..5 banks in Exynos5433 are located in two pinctrl devices: ALIVE and
IMEM. Although they are partially located in ALIVE section, the state of
their registers in IMEM section is lost after suspend/resume cycle. To
properly handle such case, those banks have to be defined with standard
'exynos5433_bank_type_off' type (with PINCFG_TYPE_CON_PDN and
PINCFG_TYPE_PUD_PDN register offsets). This automatically instructs
the generic Samsung pinctrl suspend/resume code to save and restore state
of those registers.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The comment block explaining the rationale for static pins contains
grammar errors. It appeared first in the pin control driver for R-Car
H3 ES1.x, and spread to R-Car M3-W, H3 ES2.0, and M3-N later.
Fix the grammar in all copies at once.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
This patch implements control of pull-up and pull-down. On this SoC there
is no simple mapping of GP pins to bias register bits, so we need a table.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Use the appropriate SPDX license identifier in the berlin pinctrl
driver source file and drop the previous license text.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Could only support PIN_CONFIG_INPUT_DEBOUNCE now as the HW block
is too simple to support others. But even wrt. debounce capability,
it now could only support very limited period of time to satisfy the
real usecase. But still be useful to enable the crippled HW debounce
to prevent any spurious glitches from waking up the system if the
gpio is conguired as wakeup interrupt source.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are 4 banks (GPIO0 ~ GPIO3), bank0 is in PD_PMU
subsystem, bank1/bank2/bank3 are in PD_BUS subsystem.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Armada 98dx3236 SoCs don't have a different MPP sel value for nand
specific pins so "dev" was technically correct. But all the other Armada
SoCs use "nand" in their dts and the pin is specific to the nand
interface so use "nand" for the function name.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a pair of context save/restore functions to save/restore the
state of a set of pinctrl registers. The context is lost during rtc only
suspend with ddr in self-refresh on am43xx. Currently the save/restore
is being done unconditionally. This will be optimized later with a
pdata-quirk function which will allow is to save/restore only when doing
the rtc only mode with ddr in self refresh.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The data pin 0-7 of the NAND controller are actually missing from
the nand pinctrl group, so we fix it here.
Fixes: 0f15f500ff ("pinctrl: meson: Add GXL pinctrl definitions")
Reported-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The data pin 0-7 of the NAND controller are actually missing from
the nand pinctrl group, so we fix it here.
Fixes: cd1e3b01c7 ("pinctrl: amlogic: gxbb: add nand pins")
Reported-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
I was debugging some gpio issues and I thought that the output of gpio
debugfs was telling me the high or low level of the gpios with a '1' or
a '0'. We saw a line like this though:
gpio93 : in 4 2mA pull down
and I started to think that there may be a gas leak in the building
because '4' doesn't mean high or low, and other pins said '0' or '1'. It
turns out, '4' is the function selection for the pinmux of the gpio and
not the value on the pin. Reading code helps decipher what debugfs is
actually saying.
Add support to read the input or output pin depending on how the pin is
configured so we can easily see the high or low value of the pin in
debugfs. Now the output looks like
gpio93 : in low func4 2mA pull down
which clearly shows that the pin is an input, low, with function 4 and a
2mA drive strength plus a pull down.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
DebugFS strings about pin pull status for no_keeper SoC are wrong
Fix this by adding a different string array for no_keeper SoC
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Muxing of pins MCLK1/2 determine the muxing of the corresponding clocks.
Make pinctrl driver to provide clock muxes for the CDEV1/2 pingroups, so
that main clk-controller driver could get an actual parent clock for the
CDEV1/2 clocks.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Marcel Ziswiler <marcel@ziswiler.com>
Tested-by: Marcel Ziswiler <marcel@ziswiler.com>
Tested-by: Marc Dietrich <marvin24@gmx.de>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allwinner H6 SoC has a R_PIO pin controller like other Allwinner SoCs,
which controls the PL and PM pin banks.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Properties to set initial value of pin output buffer.
This can be useful for configure hardware in overlay files, and in early
boot for checking it states in QA sanity tests.
Signed-off-by: Matheus Castello <matheus@castello.eng.br>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To keep driver up to date we add generic pinctrl binding support, which
covers the features used in this driver and has additional node properties
that this SoC has compatibility, so enabling future implementations of
these properties without the need to create new node properties in the
device trees.
The logic of this change maintain the old brcm legacy binding support in
order to keep the ABI stable.
Signed-off-by: Matheus Castello <matheus@castello.eng.br>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
I've included the pin I/O voltage control into the R8A77970 PFC driver but
it was incomplete because:
- SH_PFC_PIN_CFG_IO_VOLTAGE pin flags weren't set properly;
- sh_pfc_soc_info::ioctrl_regs wasn't set at all...
Fixes: b92ac66a18 ("pinctrl: sh-pfc: Add R8A77970 PFC support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Exynos5440 is not actively developed, there are no development
boards available and probably there are no real products with it.
Remove wide-tree support for Exynos5440.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
For a constant format without additional arguments, use seq_puts()
instead of seq_printf(). Also, it fixes the following checkpatch
warning.
WARNING: Prefer seq_puts to seq_printf
+ seq_printf(s, "N/A");
WARNING: Prefer seq_puts to seq_printf
+ seq_printf(s, "\n");
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current code comments of PIN_FUNC_ID actually is not true for
SHARE_MUX_CONF_REG case which should be a 4 u32 PIN_FUNC_ID.
Fix the comments and re-org it a bit for better extendibility
as we may add a different size for SCU based PIN_FUNC_ID later.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The unsigned integer nfuncs is being error checked with a value less
or equal to zero; this is always false if of_get_child_count returns a
-ve for an error condition since nfuncs is not signed. Fix this by
making variables nfuncs and i signed integers.
Detected with Coccinelle:
drivers/pinctrl/freescale/pinctrl-imx.c:620:6-12: WARNING: Unsigned
expression compared with zero: nfuncs <= 0
Cc: Linus Walleij <linus.walleij@linaro.org>
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is a missing break in case PIN_CONFIG_DRIVE_STRENGTH leading to
a fall-through to the PIN_CONFIG_SLEW_RATE case that performs different
checks against *arg. This looks like an unintentional missing break so
add in the break.
Detected by CoverityScan, CID#1468456, 1468459 ("Missing break in switch")
Fixes: 513d7a2f7e0f ("pinctrl: actions: Add Actions S900 pinctrl driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
s900_functions, s900_padinfo and s900_pads are local to the source and do
not need to be in global scope, so make them static.
Cleans up sparse warnings:
drivers/pinctrl/actions/pinctrl-s900.c:1445:30: warning: symbol
's900_functions' was not declared. Should it be static?
drivers/pinctrl/actions/pinctrl-s900.c:1664:20: warning: symbol
's900_padinfo' was not declared. Should it be static?
drivers/pinctrl/actions/pinctrl-s900.c:207:31: warning: symbol
's900_pads' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
