ADC & I/Q calibrations could take infinite time to comple, since they
depend on received frames. In particular the I/Q mismatch calibration
requires receiving of OFDM frames for completion. But in the 2.4GHz
band, a station could receive only CCK frames for a very long time.
And while we wait for the completion of one of the mentioned
calibrations, the NF calibration is blocked. Moreover, in some
environments, I/Q calibration is unable to complete until a correct
noise calibration will be performed due to AGC behaviour.
In order to avoid delaying NF calibration on forever, limit the maximum
duration of ADCs & I/Q calibrations. If the calibration is not completed
within the maximum time, it will be interrupted and a next calibration
will be performed. The code that selects the next calibration has been
reworked to the loop so incompleted calibration will be respinned later.
Ð maximum calibration time of 30 seconds was selected to give the
calibration enough time to complete and to not interfere with the long
(NF) calibration.
Run tested with AR9220.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424004923.17129-7-ryazanov.s.a@gmail.com
Previously after the calibration validity period is over,
calibrations are invalidated in a one at time manner. So, for AR9002
family, which has three calibrations, the full recalibration interval
becomes 3 x ATH_RESTART_CALINTERVAL. And each next calibration will be
separated by the ATH_RESTART_CALINTERVAL time from a previous one.
It seems like it is better to do whole recalibration at once. Also, this
change makes the driver behaviour a little simpler. So, invalidate all
calibrations at once at the end of the calibration validity interval.
This change affects only AR9002 chips family, since the AR9003 utilize
only a single calibration.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424004923.17129-6-ryazanov.s.a@gmail.com
NF calibration and other elements of long calibration are usually faster
than ADCs & I/Q calibrations due to independence of receiption of the
OFDM signal. Moreover sometime I/Q calibration can not be completed at
all without preceding NF calibration. This is due to AGC, which has a
habit to block a weak signal without regular NF calibration. Thus, we do
not need to deferr the long calibration forever.
So, if the long calibration is requested, then deferr the ADCs & I/Q
calibration(s) and run the longcal (the NF calibration in particular) to
obtain fresh noise data.
Run tested with AR9220.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424004923.17129-5-ryazanov.s.a@gmail.com
Each of AGC & I/Q calibrations can take a long time. Long calibration
and NF calibration in particular are forbiden for parallel run with
ADC & I/Q calibrations. So, the chip could not be ready to perform the
long calibration at the time of request. And a request to perform the
long calibration may be lost.
In order to fix this, preserve the long calibration request as a
calibration state flag and restore the long calibration request each
time the calibration function is called again (i.e. on each subsequent
ivocation of the short calibration).
This feature will be twice useful after the next change, which will
make it possible to start the long calibration before all ADCs & I/Q
calibrations are completed.
Run tested with AR9220.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424004923.17129-4-ryazanov.s.a@gmail.com
ADC calibration is only required for a 80 MHz sampling rate (i.e. for
40 MHz channels), when the chip utilizes the pair of ADCs in interleved
mode. Calibration on a 20 MHz channel will never be completed.
Previous channel check is trying to exclude all channels where the
calibration will get stuck. It effectively blocks the calibration run
for HT20 channels, but fails to exclude 20 MHz channels without HT (e.g.
legacy mode channels).
Fix this issue by reworking the channel check to explicitly allow ADCs
gain & DC offset calibrations for HT40 channels only. Also update the
complicated comment to make it clear that these calibrations are for
multi-ADC mode only.
Stuck ADCs calibration blocks the NF calibration, what could make it
impossible to work in a noisy evironment: too big Rx attentuation,
invalid RSSI value, etc. So this change is actually more of a NF
calibration fix rather then the ADC calibration fix.
Run tested with AR9220.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424004923.17129-2-ryazanov.s.a@gmail.com
When tx complete is disabled, all tx status will be set with status
HTT_TX_COMPL_STATE_ACK and indicate to mac80211 by ieee80211_tx_status,
then it does not have the statistics for retries and failed packets.
count of tx retries and tx failed of command "iw wlan0 station dump"
are both 0. If tx complete is not disabled, then firmware report the
tx status and ath10k indicate the status to mac80211, then mac80211
save the statistics and command "iw wlan0 station dump" show them.
for example:
localhost ~ # iw dev wlan0 station dump
Station 3c:28:6d:96:fd:69 (on wlan0)
inactive time: 5 ms
rx bytes: 1325012
rx packets: 6477
tx bytes: 85264
tx packets: 518
tx retries: 0
tx failed: 0
This patch only effect chips with tx complete disabled, e.g. SDIO.
with this patch, output of command "iw dev wlan0 station dump":
Station c4:04:15:5d:97:22 (on wlan0)
inactive time: 608 ms
rx bytes: 180366
rx packets: 991
tx bytes: 98765577
tx packets: 64624
tx retries: 14682
tx failed: 47086
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200423024134.10601-1-wgong@codeaurora.org
When run command "iw dev wlan0 station dump", the rx duration is 0.
When firmware indicate WMI_UPDATE_STATS_EVENTID, extended flag of
statsis not set by default, so firmware do not report rx duration.
one sample:
localhost # iw wlan0 station dump
Station c4:04:15:5d:97:22 (on wlan0)
inactive time: 48 ms
rx bytes: 21670
rx packets: 147
tx bytes: 11529
tx packets: 100
tx retries: 88
tx failed: 36
beacon loss: 1
beacon rx: 31
rx drop misc: 47
signal: -72 [-74, -75] dBm
signal avg: -71 [-74, -75] dBm
beacon signal avg: -71 dBm
tx bitrate: 54.0 MBit/s MCS 3 40MHz
rx bitrate: 1.0 MBit/s
rx duration: 0 us
This patch enable firmware's extened flag of stats by setting flag
WMI_TLV_STAT_PEER_EXTD of ar->fw_stats_req_mask which is set in
ath10k_core_init_firmware_features via WMI_REQUEST_STATS_CMDID.
After apply this patch, rx duration show value with the command:
Station c4:04:15:5d:97:22 (on wlan0)
inactive time: 883 ms
rx bytes: 44289
rx packets: 265
tx bytes: 10838
tx packets: 93
tx retries: 899
tx failed: 103
beacon loss: 0
beacon rx: 78
rx drop misc: 46
signal: -71 [-74, -76] dBm
signal avg: -70 [-74, -76] dBm
beacon signal avg: -70 dBm
tx bitrate: 54.0 MBit/s MCS 3 40MHz
rx bitrate: 1.0 MBit/s
rx duration: 358004 us
This patch do not have side effect for all chips, because function
ath10k_debug_fw_stats_request is already exported to debugfs
"fw_stats" and WMI_REQUEST_STATS_CMDID is safely sent after condition
checked by ath10k_peer_stats_enabled in ath10k_sta_statistics.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200423022758.5365-1-wgong@codeaurora.org
we are sending the reo flush command for the deleted peer
tid after the ageout period reaches 1 second. This handling
causes reo ring get full when more than 128 clients are
disconnected continuously. so added the count for flush list
and reo flush command is triggered after the list count reaches
the threshold value, it is configured as 64 (half of the reo ring).
This will avoid the situation where reo ring get full.
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587552378-4884-1-git-send-email-periyasa@codeaurora.org
The driver is allowing the invalid tx/rx chainmask configuration
(other than 1,3,7,15) set by the user. It causes the firmware
crash due to the invalid chainmask values.
Hence, reject the invalid chainmask values in the driver by not
sending the pdev set command to the firmware.
Tested hardware: QCA9888
Tested firmware: 10.4-3.10-00047
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587495512-29813-1-git-send-email-mkenna@codeaurora.org
The default credit size is 1792 bytes, but the IP mtu is 1500 bytes,
then it has about 290 bytes's waste for each data packet on sdio
transfer path for TX bundle, it will reduce the transmission utilization
ratio for data packet.
This patch enable the small credit size in firmware, firmware will use
the new credit size 1556 bytes, it will increase the transmission
utilization ratio for data packet on TX patch. It results in significant
performance improvement on TX path.
This patch only effect sdio chip, it will not effect PCI, SNOC etc.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200410061400.14231-3-wgong@codeaurora.org
The transmission utilization ratio for sdio bus for small packet is
slow, because the space and time cost for sdio bus is same for large
length packet and small length packet. So the speed of data for large
length packet is higher than small length.
Test result of different length of data:
data packet(byte) cost time(us) calculated rate(Mbps)
256 28 73
512 33 124
1024 35 234
1792 45 318
14336 168 682
28672 333 688
57344 660 695
This patch change the TX packet from single packet to a large length
bundle packet, max size is 32, it results in significant performance
improvement on TX path.
Also there's a fourth thread "ath10k_tx_complete_wq" added to ath10k as it
improves TCP RX throughput (values in Mbps):
TCP-RX TCP-TX UDP-RX UDP-TX
use workqueue_tx_complete 423 357 448 412
change it to ar->workqueue 410 360 449 414
change it to ar->workqueue_aux 405 339 446 401
This patch only effect sdio chip, it will not effect PCI, SNOC etc.
It only enable bundle for sdio chip.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200410061400.14231-2-wgong@codeaurora.org
The '==' expression itself is bool, no need to convert it to bool again.
This fixes the following coccicheck warning:
drivers/net/wireless/ath/ath11k/debug.c:198:57-62: WARNING: conversion
to bool not needed here
drivers/net/wireless/ath/ath11k/debug.c:218:58-63: WARNING: conversion
to bool not needed here
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200420123745.4159-1-yanaijie@huawei.com
This patch is to set register to allow the mbox enter sleep status
if it does not have tx traffic and wakeup it if tx traffic arrive.
After mbox enter sleep status, the soc will enter sleep status by
firmware, this will save power. The power consume drops from about
90mW to about 10mW with this patch.
This patch only effect sdio chip.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587037859-28873-3-git-send-email-kvalo@codeaurora.org
IPQ8074 HW supports three TCL rings for tx. Currently these rings
are mapped based on the Access categories, viz. VO, VI, BE, BK.
In case, one of the traffic type dominates, then it could stress
the same tcl rings. Rather, it would be optimal to make use of all
the rings in a round robin fashion irrespective of the traffic type
so that the load could be evenly distributed among all the rings.
Also, in case the selected ring is busy or full, a retry mechanism
is used to ensure other available ring is selected without dropping
the packet.
In SMP systems, this change avoids a single CPU from getting hogged
when heavy traffic of same category is transmitted.
The tx completion interrupts corresponding to the used tcl ring
would be more which causes the assigned CPU to get hogged.
Distribution of tx packets to different tcl rings helps balance
this load.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586782622-22570-1-git-send-email-srirrama@codeaurora.org
During RX, accessing the reo dest ring descriptor directly is consuming
a lot of CPU cycles. Accessing the descriptor after copying it locally
has improved CPU usage by around ~10-15% while measuring throughput
in RX DBTC test cases(all radios are involved in the throughput
measurement).
HW tested: IPQ8074
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586421797-885-1-git-send-email-mpubbise@codeaurora.org
Add the pdev index information in the peer object to validate
the peer creation. Ignore the peer creation request, if the given
MAC address is already present in the peer list with same radio.
If we allow the peer creation in above scenario, FW assert will happen.
Above scenario occurred in two cases, where Multiple AP VAP created in
the same radio.
1. when testing tool sends association request to two AP with same
MAC address
2. when a station do roaming from one AP VAP to another AP VAP.
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586343795-21422-1-git-send-email-periyasa@codeaurora.org
This sorts the actual field names too, potentially causing even more
chaos and confusion at merge time if you have edited the MAINTAINERS
file. But the end result is a more consistent layout, and hopefully
it's a one-time pain minimized by doing this just before the -rc1
release.
This was entirely scripted:
./scripts/parse-maintainers.pl --input=MAINTAINERS --output=MAINTAINERS --order
Requested-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
They are all supposed to be sorted, but people who add new entries don't
always know the alphabet. Plus sometimes the entry names get edited,
and people don't then re-order the entry.
Let's see how painful this will be for merging purposes (the MAINTAINERS
file is often edited in various different trees), but Joe claims there's
relatively few patches in -next that touch this, and doing it just
before -rc1 is likely the best time. Fingers crossed.
This was scripted with
/scripts/parse-maintainers.pl --input=MAINTAINERS --output=MAINTAINERS
but then I also ended up manually upper-casing a few entry names that
stood out when looking at the end result.
Requested-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull x86 fixes from Thomas Gleixner:
"A set of three patches to fix the fallout of the newly added split
lock detection feature.
It addressed the case where a KVM guest triggers a split lock #AC and
KVM reinjects it into the guest which is not prepared to handle it.
Add proper sanity checks which prevent the unconditional injection
into the guest and handles the #AC on the host side in the same way as
user space detections are handled. Depending on the detection mode it
either warns and disables detection for the task or kills the task if
the mode is set to fatal"
* tag 'x86-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
KVM: VMX: Extend VMXs #AC interceptor to handle split lock #AC in guest
KVM: x86: Emulate split-lock access as a write in emulator
x86/split_lock: Provide handle_guest_split_lock()
Pull time(keeping) updates from Thomas Gleixner:
- Fix the time_for_children symlink in /proc/$PID/ so it properly
reflects that it part of the 'time' namespace
- Add the missing userns limit for the allowed number of time
namespaces, which was half defined but the actual array member was
not added. This went unnoticed as the array has an exessive empty
member at the end but introduced a user visible regression as the
output was corrupted.
- Prevent further silent ucount corruption by adding a BUILD_BUG_ON()
to catch half updated data.
* tag 'timers-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ucount: Make sure ucounts in /proc/sys/user don't regress again
time/namespace: Add max_time_namespaces ucount
time/namespace: Fix time_for_children symlink
Pull scheduler fixes/updates from Thomas Gleixner:
- Deduplicate the average computations in the scheduler core and the
fair class code.
- Fix a raise between runtime distribution and assignement which can
cause exceeding the quota by up to 70%.
- Prevent negative results in the imbalanace calculation
- Remove a stale warning in the workqueue code which can be triggered
since the call site was moved out of preempt disabled code. It's a
false positive.
- Deduplicate the print macros for procfs
- Add the ucmap values to the SCHED_DEBUG procfs output for completness
* tag 'sched-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/debug: Add task uclamp values to SCHED_DEBUG procfs
sched/debug: Factor out printing formats into common macros
sched/debug: Remove redundant macro define
sched/core: Remove unused rq::last_load_update_tick
workqueue: Remove the warning in wq_worker_sleeping()
sched/fair: Fix negative imbalance in imbalance calculation
sched/fair: Fix race between runtime distribution and assignment
sched/fair: Align rq->avg_idle and rq->avg_scan_cost
Pull perf fixes from Thomas Gleixner:
"Three fixes/updates for perf:
- Fix the perf event cgroup tracking which tries to track the cgroup
even for disabled events.
- Add Ice Lake server support for uncore events
- Disable pagefaults when retrieving the physical address in the
sampling code"
* tag 'perf-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Disable page faults when getting phys address
perf/x86/intel/uncore: Add Ice Lake server uncore support
perf/cgroup: Correct indirection in perf_less_group_idx()
perf/core: Fix event cgroup tracking
Pull locking fixes from Thomas Gleixner:
"Three small fixes/updates for the locking core code:
- Plug a task struct reference leak in the percpu rswem
implementation.
- Document the refcount interaction with PID_MAX_LIMIT
- Improve the 'invalid wait context' data dump in lockdep so it
contains all information which is required to decode the problem"
* tag 'locking-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/lockdep: Improve 'invalid wait context' splat
locking/refcount: Document interaction with PID_MAX_LIMIT
locking/percpu-rwsem: Fix a task_struct refcount
Pull cifs fixes from Steve French:
"Ten cifs/smb fixes:
- five RDMA (smbdirect) related fixes
- add experimental support for swap over SMB3 mounts
- also a fix which improves performance of signed connections"
* tag '5.7-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
smb3: enable swap on SMB3 mounts
smb3: change noisy error message to FYI
smb3: smbdirect support can be configured by default
cifs: smbd: Do not schedule work to send immediate packet on every receive
cifs: smbd: Properly process errors on ib_post_send
cifs: Allocate crypto structures on the fly for calculating signatures of incoming packets
cifs: smbd: Update receive credits before sending and deal with credits roll back on failure before sending
cifs: smbd: Check send queue size before posting a send
cifs: smbd: Merge code to track pending packets
cifs: ignore cached share root handle closing errors
Pull NFS client bugfix from Trond Myklebust:
"Fix an RCU read lock leakage in pnfs_alloc_ds_commits_list()"
* tag 'nfs-for-5.7-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
pNFS: Fix RCU lock leakage
Pull dma-mapping fixes from Christoph Hellwig:
- fix an integer truncation in dma_direct_get_required_mask
(Kishon Vijay Abraham)
- fix the display of dma mapping types (Grygorii Strashko)
* tag 'dma-mapping-5.7-1' of git://git.infradead.org/users/hch/dma-mapping:
dma-debug: fix displaying of dma allocation type
dma-direct: fix data truncation in dma_direct_get_required_mask()
Pull more Kbuild updates from Masahiro Yamada:
- raise minimum supported binutils version to 2.23
- remove old CONFIG_AS_* macros that we know binutils >= 2.23 supports
- move remaining CONFIG_AS_* tests to Kconfig from Makefile
- enable -Wtautological-compare warnings to catch more issues
- do not support GCC plugins for GCC <= 4.7
- fix various breakages of 'make xconfig'
- include the linker version used for linking the kernel into
LINUX_COMPILER, which is used for the banner, and also exposed to
/proc/version
- link lib-y objects to vmlinux forcibly when CONFIG_MODULES=y, which
allows us to remove the lib-ksyms.o workaround, and to solve the last
known issue of the LLVM linker
- add dummy tools in scripts/dummy-tools/ to enable all compiler tests
in Kconfig, which will be useful for distro maintainers
- support the single switch, LLVM=1 to use Clang and all LLVM utilities
instead of GCC and Binutils.
- support LLVM_IAS=1 to enable the integrated assembler, which is still
experimental
* tag 'kbuild-v5.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (36 commits)
kbuild: fix comment about missing include guard detection
kbuild: support LLVM=1 to switch the default tools to Clang/LLVM
kbuild: replace AS=clang with LLVM_IAS=1
kbuild: add dummy toolchains to enable all cc-option etc. in Kconfig
kbuild: link lib-y objects to vmlinux forcibly when CONFIG_MODULES=y
MIPS: fw: arc: add __weak to prom_meminit and prom_free_prom_memory
kbuild: remove -I$(srctree)/tools/include from scripts/Makefile
kbuild: do not pass $(KBUILD_CFLAGS) to scripts/mkcompile_h
Documentation/llvm: fix the name of llvm-size
kbuild: mkcompile_h: Include $LD version in /proc/version
kconfig: qconf: Fix a few alignment issues
kconfig: qconf: remove some old bogus TODOs
kconfig: qconf: fix support for the split view mode
kconfig: qconf: fix the content of the main widget
kconfig: qconf: Change title for the item window
kconfig: qconf: clean deprecated warnings
gcc-plugins: drop support for GCC <= 4.7
kbuild: Enable -Wtautological-compare
x86: update AS_* macros to binutils >=2.23, supporting ADX and AVX2
crypto: x86 - clean up poly1305-x86_64-cryptogams.S by 'make clean'
...
I do not longer work for credativ Germany.
Please, use my private email address instead.
This is for the case when people want to CC me on
patches sent from my old business email address.
Signed-off-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Another brown paper bag moment. pnfs_alloc_ds_commits_list() is leaking
the RCU lock.
Fixes: a9901899b6 ("pNFS: Add infrastructure for cleaning up per-layout commit structures")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Two types of #AC can be generated in Intel CPUs:
1. legacy alignment check #AC
2. split lock #AC
Reflect #AC back into the guest if the guest has legacy alignment checks
enabled or if split lock detection is disabled.
If the #AC is not a legacy one and split lock detection is enabled, then
invoke handle_guest_split_lock() which will either warn and disable split
lock detection for this task or force SIGBUS on it.
[ tglx: Switch it to handle_guest_split_lock() and rename the misnamed
helper function. ]
Suggested-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Xiaoyao Li <xiaoyao.li@intel.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Link: https://lkml.kernel.org/r/20200410115517.176308876@linutronix.de
