cros_ec hwmon driver probes available thermal sensors when probing the
driver. Register these thermal sensors to the thermal framework as well
via setting HWMON_C_REGISTER_TZ as a chip info, such that thermal
framework can adopt these sensors as well.
To make cros_ec registrable to thermal framework, the cros_ec dts need
the corresponding changes:
&cros_ec {
#thermal-sensor-cells = <1>;
};
Signed-off-by: Sung-Chi, Li <lschyi@chromium.org>
Message-ID: <20241113024000.3327161-1-lschyi@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
According to the ACPI specification, the _PMD method is optional. The
acpi_power_meter driver shouldn't fail to load if the platform has no
_PMD method.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Message-ID: <20241112021228.22914-1-lihuisong@huawei.com>
[groeck: Reworded commit description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Delta AFC0612DB-F00 fan has to be set to at least 30% PWM duty cycle
to spin up from a stopped state, and can be afterward throttled down to
lower PWM duty cycle. Introduce support for operating such fans which
need to start at higher PWM duty cycle first and can slow down next.
Introduce two new DT properties, "fan-stop-to-start-percent" and
"fan-stop-to-start-us". The former describes the minimum percent
of fan RPM at which it will surely spin up from stopped state. This
value can be found in the fan datasheet and can be converted to PWM
duty cycle easily. The "fan-stop-to-start-us" describes the minimum
time in microseconds for which the fan has to be set to stopped state
start RPM for the fan to surely spin up.
Adjust the PWM setting code such that if the PWM duty cycle is below
the minimum duty cycle needed by the fan to spin up from stopped state,
then first set the PWM duty cycle to the minimum duty cycle needed
by the fan to spin up from stopped state, then wait the time necessary
for the fan to spin up from stopped state, and finally set the PWM duty
cycle to the one desired by user.
Signed-off-by: Marek Vasut <marex@denx.de>
Message-ID: <20241106185925.223736-2-marex@denx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Delta AFC0612DB-F00 fan has to be set to at least 30% PWM duty cycle
to spin up from a stopped state, and can be afterward throttled down to
lower PWM duty cycle. Introduce support for operating such fans which
need to start at higher PWM duty cycle first and can slow down next.
Document two new DT properties, "fan-stop-to-start-percent" and
"fan-stop-to-start-usec". The former describes the minimum percent
of fan RPM at which it will surely spin up from stopped state. This
value can be found in the fan datasheet and can be converted to PWM
duty cycle easily. The "fan-stop-to-start-usec" describes the minimum
time in microseconds for which the fan has to be set to stopped state
start RPM for the fan to surely spin up.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Message-ID: <20241106185925.223736-1-marex@denx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add compatible string 'nxp,p3t1085' since p3t1085's register layout is the
same as tmp108.
The p3t1085 supports I3C interface.
Update document tmp108.rst and Kconfig's help context.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Message-ID: <20241111-p3t1085-v3-2-bff511550aad@nxp.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix several grammatical issues in the fan speed trip points documentation:
- Replace awkward "which % the fan should run at at" construction with
clearer "that specify the percentage at which"
- Fix incorrect "is chip depended" to "are chip dependent" for correct
verb agreement and adjective form
- Improve readability by reorganizing first sentence and separating the
complex explanation into simpler parts
- Add hyphen before "see" to improve readability
- Remove redundant "at" in temperature description
No functional changes, documentation only.
Signed-off-by: Abhinav Saxena <xandfury@gmail.com>
Message-ID: <20241107013849.47833-1-xandfury@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pmbus_write_smbalert_mask() ignores the errors if the chip can't set
smbalert mask the standard way. It is not necessarily a problem for the irq
support if the chip is otherwise properly setup but it may leave an
uncleared fault behind.
pmbus_core will pick the fault on the next register_check(). The register
check will fails regardless of the actual register support by the chip.
This leads to missing attributes or debugfs entries for chips that should
provide them.
We cannot rely on register_check() as PMBUS_SMBALERT_MASK may be read-only.
Unconditionally clear the page fault after setting PMBUS_SMBALERT_MASK to
avoid the problem.
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Fixes: 221819ca4c ("hwmon: (pmbus/core) Add interrupt support")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Message-ID: <20241105-tps25990-v4-5-0e312ac70b62@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use _pmbus_read_byte_data() rather than calling smbus directly to check
the write protection status. This give a chance to device implementing
write protection differently to report back on the actual write protection
status.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Message-ID: <20241105-tps25990-v4-2-0e312ac70b62@baylibre.com>
[groeck: Fix page parameter of _pmbus_read_byte_data()]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
PMBUS_NO_WRITE_PROTECT and PMBUS_USE_COEFFICIENTS_CMD flags have been added
to pmbus, but the corresponding documentation was not updated.
Update the documentation before adding new flags
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Message-ID: <20241105-tps25990-v4-1-0e312ac70b62@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
SY24655: Support for current and voltage detection as well as
power calculation.
Signed-off-by: Wenliang Yan <wenliang202407@163.com>
Message-ID: <20241106150547.2538-1-wenliang202407@163.com>
[groeck: Changed order of compatible entries;
dropped spurious extra return statement in is_visible();
fixed code problems]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for LTC7841. The LTC7841 is a high performance
PolyPhase® single output synchronous boost converter controller.
Multiphase operation reduces input and output capacitor
requirements and allows the use of smaller inductors than the
single-phase equivalent.
The relevant registers in the LTC7841 are similar to the
LTC7880, only reduced by some amount. So it's just a matter of adding
the chip id. The device also doesn't support polling, on top of the
reduced register set, so a separate case for setting the chip info is
added.
Signed-off-by: Mariel Tinaco <Mariel.Tinaco@analog.com>
Message-ID: <20241029013734.293024-4-Mariel.Tinaco@analog.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The NCT7363Y is a fan controller which provides up to 16
independent FAN input monitors. It can report each FAN input count
values. The NCT7363Y also provides up to 16 independent PWM
outputs. Each PWM can output specific PWM signal by manual mode to
control the FAN duty outside.
Signed-off-by: Ban Feng <kcfeng0@nuvoton.com>
Message-ID: <20241022052905.4062682-3-kcfeng0@nuvoton.com>
[groeck: Dropped unnecessary variable initialization, and , after { }]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Remove vicor,pli1209bc from trivial-devices as it requires additional
properties and does not fit into the trivial devices category.
Add new bindings for Vicor pli1209bc, a Digital Supervisor with
Isolation for use with BCM Bus Converter Modules.
VR rails are defined under regulator node as expected by pmbus driver.
Signed-off-by: Naresh Solanki <naresh.solanki@9elements.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Message-ID: <20241021123044.3648960-1-naresh.solanki@9elements.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Per his request, remove Aleksandr Mezin as maintainer of the
NZXT-SMART2 hardware monitoring driver.
Cc: Aleksandr Mezin <mezin.alexander@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/hwmonto use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
While touching these files, make indention of the struct initializer
consistent in several files.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Message-ID: <20241017155900.137357-2-u.kleine-koenig@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for manipulating the internal heater of sht4x devices.
Enabling the heater removes condensed water from the sensor surface
which disturbs the relative humidity measurements.
The heater can operate at three heating levels (20, 110 or 200
milliwatts). Also, two heating durations may be selected (0.1 or 1s).
Once the heating time elapses the heater is automatically switched off.
Changes since v3:
* struct sht4x_data: add heating_complete timestamp
* struct sht4x_data: add data_pending flag
* heater_enable_store: return -EINVAL if input != 1
* heater_enable_store: check for data->heating_complete and update it
* heater_enable_store: set data_pending flag after heating request
* sht4x_read_values: msleep if heating in progress
* sht4x_read_values: dont send measurement request if data_pending
* heater_enable attr: make it RW
* Documentation: update info about heater_enable attr
Changes since v2:
* heater_enable_store: remove unnecessary if
* Documentation: remove incorrect info about turning off the heater
* be more specific in the patch description
Changes since v1:
* explain the use case of the new attributes set
* heater_enable attr: make it write-only
* heater_enable_store: define cmd as u8 instead of u8*
* heater_enable_store: remove unreachable data path
* heater_enable_store: remove unnecessary lock
* heater_enable_store: call i2c_master_send only if status==true
* define attributes as DEVICE_ATTR_* instead of SENSOR_DEVICE_ATTR_*
Signed-off-by: Antoni Pokusinski <apokusinski01@gmail.com>
Message-ID: <20240930205346.2147-1-apokusinski01@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Several drivers return the same static value in their is_visible
callback, what results in code duplication. Therefore add an option
for drivers to specify a static visibility directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Message-ID: <89690b81-2c73-47ae-9ae9-45c77b45ca0c@gmail.com>
groeck: Renamed hwmon_ops_is_visible -> hwmon_is_visible
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Theobroma Systems Mule is an MCU that emulates a set of I2C devices,
among which is an amc6821 and other devices that are reachable through
an I2C-mux.
The devices on the mux can be selected by writing the appropriate device
number to an I2C config register (amc6821: reg 0xff)
Implement "tsd,mule" compatible to instantiate the I2C-mux platform device
when probing the amc6821.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Farouk Bouabid <farouk.bouabid@cherry.de>
Message-ID: <20240906-dev-mule-i2c-mux-v8-4-dbd28a150e41@cherry.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
INA260 is similar to other chips of the series, except it has an internal
shunt resistor. The calibration register is therefore not present. Also,
the current register address was changed, though that does not matter for
the driver since the shunt voltage register (which is now the current
register) value is already used to read the current.
Cc: Loic Guegan <loic.guegan@mailbox.org>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add configuration flag indicating if the chip supports alerts and limits
to prepare for adding INA260 support.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
These drivers don't use the driver_data member of struct i2c_device_id,
so don't explicitly initialize this member.
This prepares putting driver_data in an anonymous union which requires
either no initialization or named designators. But it's also a nice
cleanup on its own.
While touching these structs, also remove commas after the sentinel
entries and use a consistent indention style.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Message-ID: <20240918123150.1540161-7-u.kleine-koenig@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull clk fixes from Stephen Boyd:
"A handful of Qualcomm clk driver fixes:
- Correct flags for X Elite USB MP GDSC and pcie pipediv2 clocks
- Fix alpha PLL post_div mask for the cases where width is not
specified
- Avoid hangs in the SM8350 video driver (venus) by setting HW_CTRL
trigger feature on the video clocks"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: qcom: gcc-x1e80100: Fix USB MP SS1 PHY GDSC pwrsts flags
clk: qcom: gcc-x1e80100: Fix halt_check for pipediv2 clocks
clk: qcom: clk-alpha-pll: Fix pll post div mask when width is not set
clk: qcom: videocc-sm8350: use HW_CTRL_TRIGGER for vcodec GDSCs
