TRBE context can be lost when a CPU enters low power states. If a trace
source is restored while TRBE is not, tracing may run without an active
sink, which can lead to hangs on some devices (e.g., Pixel 9).
The save and restore flows are described in the section K5.5 "Context
switching" of Arm ARM (ARM DDI 0487 L.a). This commit adds save and
restore callbacks with following the software usages defined in the
architecture manual.
During the restore flow, since TRBLIMITR_EL1.E resets to 0 on a warm
reset, the trace buffer unit is disabled when idle resume, it is safe to
restore base/pointer/status registers first and program TRBLIMITR_EL1
last.
Signed-off-by: Yabin Cui <yabinc@google.com>
Co-developed-by: Leo Yan <leo.yan@arm.com>
Signed-off-by: Leo Yan <leo.yan@arm.com>
Reviewed-by: James Clark <james.clark@linaro.org>
Tested-by: James Clark <james.clark@linaro.org>
Reviewed-by: Yeoreum Yun <yeoreum.yun@arm.com>
Tested-by: Jie Gan <jie.gan@oss.qualcomm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20260515-arm_coresight_path_power_management_improvement-v14-25-f88c4a3ecfe9@arm.com
Extend the CPU PM flow to control the path: disable from source up to
the node before the sink, then re-enable the same range on restore.
To avoid latency, control it up to the node before the sink.
Track per-CPU PM restore failures using percpu_pm_failed. Once a CPU
hits a restore failure, set the percpu_pm_failed and return NOTIFY_BAD
on subsequent notifications to avoid repeating half-completed
transitions.
Setting percpu_pm_failed permanently blocks CPU PM on that CPU. Such
failures are typically seen during development; disabling PM operations
simplifies the implementation, and a warning highlights the issue.
Clear this flag when the source device is unregistered.
Reviewed-by: James Clark <james.clark@linaro.org>
Tested-by: Jie Gan <jie.gan@oss.qualcomm.com>
Reviewed-by: Yeoreum Yun <yeoreum.yun@arm.com>
Tested-by: James Clark <james.clark@linaro.org>
Signed-off-by: Leo Yan <leo.yan@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20260515-arm_coresight_path_power_management_improvement-v14-23-f88c4a3ecfe9@arm.com
CPU PM notifiers need to control only part of a path instead of always
operating on the full path.
Add internal enable and disable helpers that take an inclusive node
range [from, to], validate that the requested nodes are ordered before
using them.
Update the existed coresight_{enable|disable}_path() interfaces as
full-path wrappers by passing the first and last path nodes. The helpers
coresight_path_{first|last}_node() are provided for conveniently
fetching the first and last nodes on the path.
In coresight_enable_path_from_to(), if a failure occurs at the last node
in the range, no device is actually enabled in this case, bail out
directly.
Tested-by: Jie Gan <jie.gan@oss.qualcomm.com>
Reviewed-by: Yeoreum Yun <yeoreum.yun@arm.com>
Reviewed-by: James Clark <james.clark@linaro.org>
Tested-by: James Clark <james.clark@linaro.org>
Signed-off-by: Leo Yan <leo.yan@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20260515-arm_coresight_path_power_management_improvement-v14-16-f88c4a3ecfe9@arm.com
coresight_enable_path() enables helpers attached to every device in
the path, including those bound to the source. However,
coresight_disable_path() skips the source node, so source helpers had
to be disabled separately in coresight_disable_source().
Move source helper disabling into coresight_disable_path() instead.
Make coresight_disable_path_from() start from the passed node nd, so
it can also disable helpers on the source. Update the comments
accordingly.
As coresight_disable_path_from() now changes its semantics from
"start beyond nd" to "start from nd", update the failure handling in
coresight_enable_path(). If enabling a node fails, iterate to the
previous node (the last successfully enabled one) and pass it to
coresight_disable_path_from() for rollback.
Tested-by: Jie Gan <jie.gan@oss.qualcomm.com>
Reviewed-by: Yeoreum Yun <yeoreum.yun@arm.com>
Reviewed-by: James Clark <james.clark@linaro.org>
Tested-by: James Clark <james.clark@linaro.org>
Signed-off-by: Leo Yan <leo.yan@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20260515-arm_coresight_path_power_management_improvement-v14-15-f88c4a3ecfe9@arm.com
The current implementation only saves and restores the context for ETM
sources while ignoring the context of links. However, if funnels or
replicators on a linked path resides in a CPU or cluster power domain,
the hardware context for the link will be lost after resuming from low
power states.
To support context management for links during CPU low power modes, a
better way is to implement CPU PM callbacks in the Arm CoreSight core
layer. As the core layer has sufficient information for linked paths,
from tracers to links, which can be used for power management.
As a first step, this patch registers CPU PM notifier in the core layer.
If a source device provides callbacks for saving and restoring context,
these callbacks will be invoked in CPU suspend and resume.
Reviewed-by: James Clark <james.clark@linaro.org>
Tested-by: James Clark <james.clark@linaro.org>
Reviewed-by: Yeoreum Yun <yeoreum.yun@arm.com>
Tested-by: Jie Gan <jie.gan@oss.qualcomm.com>
Signed-off-by: Leo Yan <leo.yan@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20260515-arm_coresight_path_power_management_improvement-v14-11-f88c4a3ecfe9@arm.com
etm_setup_aux() fetches the per-CPU source pointer while preparing perf
AUX trace paths. This can race with CoreSight device unregistration, the
ETM device may has been released while the AUX setup still use it,
leading to use-after-free.
Move per-CPU path construction into etm_event_build_path() and use
the coresight_{get|put}_percpu_source_ref() pairs to take and drop
the device references, this ensures the device is safe to access during
path construction.
Update comments accordingly. Document a PREEMPT_RT corner case: the
put_device() may release resources while coresight_dev_lock (a raw
spinlock) is held, and the release may attempt to acquire a spinlock
that becomes sleepable under PREEMPT_RT. This will be fixed in the
future.
Reviewed-by: Yeoreum Yun <yeoreum.yun@arm.com>
Reviewed-by: James Clark <james.clark@linaro.org>
Tested-by: James Clark <james.clark@linaro.org>
Tested-by: Jie Gan <jie.gan@oss.qualcomm.com>
Signed-off-by: Leo Yan <leo.yan@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20260515-arm_coresight_path_power_management_improvement-v14-10-f88c4a3ecfe9@arm.com
ETM perf callbacks currently use the per-CPU csdev_src pointer, which
can race with updates during device registration and unregistration.
The AUX setup already builds and stores the path in the event data.
Use this path to retrieve the source instead of csdev_src to avoid
the race.
Export coresight_get_source() and add etm_event_get_ctxt_path() to
retrieve the context's path and its source with READ_ONCE() /
WRITE_ONCE() accessors. Give the comments to explain why this
approach is safe when pause or resume callbacks preempt the disable
callback (e.g. via NMI).
Reviewed-by: Yeoreum Yun <yeoreum.yun@arm.com>
Reviewed-by: James Clark <james.clark@linaro.org>
Tested-by: James Clark <james.clark@linaro.org>
Tested-by: Jie Gan <jie.gan@oss.qualcomm.com>
Signed-off-by: Leo Yan <leo.yan@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20260515-arm_coresight_path_power_management_improvement-v14-7-f88c4a3ecfe9@arm.com
The hotplug lock is acquired and released in etm{3|4}_disable_sysfs(),
which are low-level functions. This prevents us from a new solution for
hotplug.
Firstly, hotplug callbacks cannot invoke etm{3|4}_disable_sysfs() to
disable the source; otherwise, a deadlock issue occurs. The reason is
that, in the hotplug flow, the kernel acquires the hotplug lock before
calling callbacks. Subsequently, if coresight_disable_source() is
invoked and it calls etm{3|4}_disable_sysfs(), the hotplug lock will be
acquired twice, leading to a double lock issue.
Secondly, when hotplugging a CPU on or off, if we want to manipulate all
components on a path attached to the CPU, we need to maintain atomicity
for the entire path. Otherwise, a race condition may occur with users
setting the same path via the Sysfs knobs, ultimately causing mess
states in CoreSight components.
This patch moves the hotplug locking from etm{3|4}_disable_sysfs() into
enable_source_store(). As a result, when users control the Sysfs knobs,
the whole flow is protected by hotplug locking, ensuring it is mutual
exclusive with hotplug callbacks.
Note, the paired function etm{3|4}_enable_sysfs() does not use hotplug
locking, which is why this patch does not modify it.
Reviewed-by: Mike Leach <mike.leach@linaro.org>
Tested-by: James Clark <james.clark@linaro.org>
Reviewed-by: Yeoreum Yun <yeoreum.yun@arm.com>
Reviewed-by: James Clark <james.clark@linaro.org>
Tested-by: Jie Gan <jie.gan@oss.qualcomm.com>
Signed-off-by: Leo Yan <leo.yan@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20260515-arm_coresight_path_power_management_improvement-v14-6-f88c4a3ecfe9@arm.com
In coresight_enable_sysfs(), for non-CPU sources (SOFTWARE, TPDM,
OTHERS), the source device is enabled via coresight_enable_source_sysfs()
before idr_alloc_u32() maps the path. If idr_alloc_u32() fails, the
original code jumped directly to err_source, which only calls
coresight_disable_path() and coresight_release_path(). The source device
was left enabled with an incremented refcnt but no path tracked for it,
leaving the device in an inconsistent state.
Disable the source before jumping to err_source so the enable and path
operations are fully unwound.
Fixes: 5c0016d7b3 ("coresight: core: Use IDR for non-cpu bound sources' paths.")
Signed-off-by: Jie Gan <jie.gan@oss.qualcomm.com>
Reviewed-by: Yeoreum Yun <yeoreum.yun@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20260515-arm_coresight_path_power_management_improvement-v14-1-f88c4a3ecfe9@arm.com
When coresight_path_assign_trace_id() cannot assign a valid trace ID,
coresight_enable_sysfs() takes the err_path goto with ret still 0,
returning success to the caller despite no trace session being started.
Change coresight_path_assign_trace_id() to return int, moving the
IS_VALID_CS_TRACE_ID() check inside it so it returns -EINVAL on failure
and 0 on success. Update both callers to propagate this return value
directly instead of inspecting path->trace_id after the call.
Fixes: d87d76d823 ("Coresight: Allocate trace ID after building the path")
Reviewed-by: James Clark <james.clark@linaro.org>
Reviewed-by: Richard Cheng <icheng@nvidia.com>
Signed-off-by: Jie Gan <jie.gan@oss.qualcomm.com>
Reviewed-by: Leo Yan <leo.yan@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20260512-fix-trace-id-error-v4-1-eb3de789767a@oss.qualcomm.com
System register ETMs and ETE are unlikely to be preserved on CPU power
down. The ETE DT binding also never documented
"arm,coresight-loses-context-with-cpu" so nobody would have legitimately
been able to use that binding to fix it and ACPI has no such binding at
all.
Fix it by hard coding the setting for sysreg ETMs (ETE is always sysreg)
or ACPI boots. Use a local variable when setting up save_state so that
it's immune to concurrent probing when devices have different
configurations which is an issue with modifying the global.
This fixes the following error when using Coresight with ACPI on the FVP
which supports CPU PM:
coresight ete0: External agent took claim tag
WARNING: drivers/hwtracing/coresight/coresight-core.c:248 at coresight_disclaim_device_unlocked+0xe0/0xe8, CPU#0: perf/117
Fixes: 35e1c9163e ("coresight: ete: Add support for ETE tracing")
Signed-off-by: James Clark <james.clark@linaro.org>
Reviewed-by: Leo Yan <leo.yan@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20260505-james-cs-ete-pm_save_enable-v3-1-485d21dd79b8@linaro.org
When specifying a 2GB AUX buffer, the ETR driver ends up allocating only
a 1MB buffer instead:
# echo 'file coresight-tmc-etr.c +p' > \
/sys/kernel/debug/dynamic_debug/control
# perf record -e cs_etm/@tmc_etr0,timestamp=0/u -C 0 -m ,2G -- test
coresight tmc_etr0: allocated buffer of size 1024KB in mode 0
The page index is an 'int' type, and shifting it by PAGE_SHIFT overflows
when the resulting value exceeds 2GB. This produces a negative value,
causing the driver to fall back to the minimum buffer size (1MB).
Cast the page index to a wider type to accommodate large buffer sizes.
Also fix a similar issue in the buffer offset calculation.
Reported-by: Michiel van Tol <michiel.vantol@arm.com>
Fixes: 99443ea19e ("coresight: Add generic TMC sg table framework")
Fixes: eebe8dbd86 ("coresight: tmc: Decouple the perf buffer allocation from sysfs mode")
Signed-off-by: Leo Yan <leo.yan@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20260217-arm_coresight_fix_big_buffer_size-v1-1-774e893d8e3f@arm.com
In cti_plat_process_filter_sigs(), after allocating a temporary
cti_trig_grp struct via kzalloc_obj(), the code never assigns tg->nr_sigs
= nr_filter_sigs. Since kzalloc zero-initialises the struct, tg->nr_sigs
remains 0. cti_plat_read_trig_group() guards with:
if (!tgrp->nr_sigs)
return 0;
so it returns immediately without reading any signal indices from DT.
Fix by assigning tg->nr_sigs before calling cti_plat_read_trig_group().
Fixes: a5614770ab ("coresight: cti: Add device tree support for custom CTI")
Signed-off-by: Yingchao Deng <yingchao.deng@oss.qualcomm.com>
Reviewed-by: Leo Yan <leo.yan@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20260426-nr_sigs-v1-1-3b9df99dab97@oss.qualcomm.com
Pull sh fix from John Paul Adrian Glaubitz:
"The ZERO_PAGE consolidation in v7.1, introduced a regression on sh
which made these systems unbootable.
The problem was that on sh, the initial boot parameters were
previously referenced as an array and after 6215d9f447 ("arch, mm:
consolidate empty_zero_page"), they were referenced as a pointer which
caused wrong code generation and boot hang.
This changes the declaration back to being an array which fixes the
boot hang"
* tag 'sh-for-v7.1-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux:
sh: Fix fallout from ZERO_PAGE consolidation
Pull slab fixes from Vlastimil Babka:
- Stable fixes for CONFIG_SMP=n where _nolock() allocations in NMI both
at kmalloc and page allocator levels are not properly protected by
the spin_trylock() semantics on !SMP (Harry Yoo)
* tag 'slab-for-7.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab:
mm/slab: return NULL early from kmalloc_nolock() in NMI on UP
mm/page_alloc: return NULL early from alloc_frozen_pages_nolock() in NMI on UP
Pull locking fix from Ingo Molnar:
"Fix lockup in requeue-PI during signal/timeout wakeups, by Sebastian
Andrzej Siewior"
* tag 'locking-urgent-2026-05-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
futex: Prevent lockup in requeue-PI during signal/ timeout wakeup
Pull scheduler fixes from Ingo Molnar:
- Fix the delayed dequeue negative lag increase fix in the
fair scheduler (Peter Zijlstra)
- Fix wakeup_preempt_fair() to do proper delayed dequeue
(Vincent Guittot)
- Clear sched_entity::rel_deadline when initializing
forked entities, which bug can cause all tasks to be
EEVDF-ineligible, causing a NULL pointer dereference
crash in pick_next_entity() (Zicheng Qu)
* tag 'sched-urgent-2026-05-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Clear rel_deadline when initializing forked entities
sched/fair: Fix wakeup_preempt_fair() vs delayed dequeue
sched/fair: Fix the negative lag increase fix
Consolidation of empty_zero_page declarations broke boot on sh.
sh stores its initial boot parameters in a page reserved in
arch/sh/kernel/head_32.S. Before commit 6215d9f447 ("arch, mm:
consolidate empty_zero_page") this page was referenced in C code
as an array and after that commit it is referenced as a pointer.
This causes wrong code generation and boot hang.
Declare boot_params_page as an array to fix the issue.
Reported-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Tested-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Fixes: 6215d9f447 ("arch, mm: consolidate empty_zero_page")
Signed-off-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Pull crypto fix from Herbert Xu:
- Reject algorithms with authsizes that are too short in authencesn
* tag 'v7.1-p3' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: authencesn - reject short ahash digests during instance creation
Pull ntfs fixes from Namjae Jeon:
- Fix a NULL pointer dereference in ntfs_index_walk_down() by
validating index block allocation
- Fix a memory leak of the symlink target string in
ntfs_reparse_set_wsl_symlink() during error paths
- Prevent VCN overflow and validate lowest_vcn in
ntfs_mapping_pairs_decompress() to avoid runlist corruption
- Fix a page reference leak in ntfs_write_iomap_end_resident()
when attribute search context allocation fails
- Fix an invalid PTR_ERR() usage on a valid folio pointer in
__ntfs_bitmap_set_bits_in_run()
- Correct directory link counting by dropping nlink only when
the MFT record link count reaches zero for WIN32/DOS aliases
- Fix an uninitialized variable in ntfs_mapping_pairs_decompress()
by returning an error pointer directly
* tag 'ntfs-for-7.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/linkinjeon/ntfs:
ntfs: Use return instead of goto in ntfs_mapping_pairs_decompress()
ntfs: drop nlink once for WIN32/DOS aliases
ntfs: fix invalid PTR_ERR() usage in __ntfs_bitmap_set_bits_in_run()
ntfs: fix error handling in ntfs_write_iomap_end_resident()
ntfs: fix VCN overflow in ntfs_mapping_pairs_decompress()
ntfs: fix WSL symlink target leak on reparse failure
ntfs: fix NULL dereference in ntfs_index_walk_down()
Pull drm fixes from Dave Airlie:
"Fixes for rc2, the usual amdgpu/xe double header, I think xe had a
couple of weeks combined due to some maintainer access issues,
otherwise there's just a few misc fixes and documentation fixups.
core and helpers:
- calculate framebuffer geometry with format helpers
- fix docs
amdgpu:
- GFX12 fix for CONFIG_DRM_DEBUG_MM configs
- Fix DC analog support
- Userq fixes
- GART placement fix
- Aldebaran SMU fixes
- AMDGPU_INFO_READ_MMR_REG fix
- UVD 3.1 fix
- GC 6 TCC fix
- Fix root reservation in amdgpu_vm_handle_fault()
- RAS fix
- Module reload fix for APUs
- Fix build for CONFIG_DRM_FBDEV_EMULATION=n
- IGT DWB regression fix
- GC 11.5.4 fix
- VCN user fence fixes
- JPEG user fence fixes
- SMU 13.0.6 fix
- VCN 3/4 IB parser fixes
- NV3x+ dGPU vblank fix
- DCE6/8 fixes for LVDS/eDP panels without an EDID
amdkfd:
- Fix for when CONFIG_HSA_AMD is not set
- SVM fixes
xe:
- uapi: Add missing pad and extensions check
- uapi: Reject unsafe PAT indices for CPU cached memory
- Drop registration of guc_submit_wedged_fini from xe_guc_submit_wedge
- Xe3p tuning and workaround fixes
- USE drm mm instead of drm SA for CCS read/write
- Fix leaks and null derefs
- Fix Wa_18022495364
appletbdrm:
- allocate protocol buffers with kvzalloc()
dma-buf:
- fix docs
imagination:
- avoid segfault in debugfs
ofdrm:
- put PCI device reference on errors
udl:
- increase USB timeout"
* tag 'drm-fixes-2026-05-02' of https://gitlab.freedesktop.org/drm/kernel: (77 commits)
drm/xe/uapi: Reject coh_none PAT index for CPU_ADDR_MIRROR
drm/xe/uapi: Reject coh_none PAT index for CPU cached memory in madvise
drm/xe/xelp: Fix Wa_18022495364
drm/xe/gsc: Fix BO leak on error in query_compatibility_version()
drm/xe/eustall: Fix drm_dev_put called before stream disable in close
drm/xe: Fix error cleanup in xe_exec_queue_create_ioctl()
drm/xe: Fix dma-buf attachment leak in xe_gem_prime_import()
drm/xe: Fix bo leak in xe_dma_buf_init_obj() on allocation failure
drm/xe/bo: Fix bo leak on GGTT flag validation in xe_bo_init_locked()
drm/xe/bo: Fix bo leak on unaligned size validation in xe_bo_init_locked()
drm/xe: Fix potential NULL deref in xe_exec_queue_tlb_inval_last_fence_put_unlocked
drm/xe/vf: Use drm mm instead of drm sa for CCS read/write
drm/xe: Add memory pool with shadow support
drm/xe/debugfs: Correct printing of register whitelist ranges
drm/xe: Mark ROW_CHICKEN5 as a masked register
drm/xe/tuning: Use proper register offset for GAMSTLB_CTRL
drm/xe/xe3p_lpg: Add missing indirect ring state feature flag
drm/xe: Drop redundant rtp entries for Wa_14019988906 & Wa_14019877138
drm/xe/vm: Add missing pad and extensions check
drm/xe: Drop registration of guc_submit_wedged_fini from xe_guc_submit_wedge()
...
Pull arm64 fixes from Catalin Marinas:
- Avoid writing an uninitialised stack variable to POR_EL0 on sigreturn
if the poe_context record is absent
- Reserve one more page for the early 4K-page kernel mapping to cover
the extra [_text, _stext) split introduced by the non-executable
read-only mapping
- Force the arch_local_irq_*() wrappers to be __always_inline so that
noinstr entry and idle paths cannot call out-of-line, instrumentable
copies
- Fix potential sign extension in the arm64 SCS unwinder's DWARF
advance_loc4 decoding
- Tolerate arm64 ACPI platforms with only WFI and no deeper PSCI idle
states, restoring cpuidle registration on such systems
- Include the UAPI <asm/ptrace.h> header in the arm64 GCS libc test
rather than carrying a duplicate struct user_gcs definition (the
original #ifdef NT_ARM_GCS was wrong to cover the structure
definition as it would be masked out if the toolchain defined it)
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: signal: Preserve POR_EL0 if poe_context is missing
arm64: Reserve an extra page for early kernel mapping
kselftest/arm64: Include <asm/ptrace.h> for user_gcs definition
ACPI: arm64: cpuidle: Tolerate platforms with no deep PSCI idle states
arm64/irqflags: __always_inline the arch_local_irq_*() helpers
arm64/scs: Fix potential sign extension issue of advance_loc4
Pull selinux fixes from Paul Moore:
- Ensure SELinux is always properly accessing its own sock LSM state
- Only reserve an xattr slot for SELinux if it will be used
- Fix a SELinux auditing regression in the directory avdcache
* tag 'selinux-pr-20260501' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
selinux: fix avdcache auditing
selinux: don't reserve xattr slot when we won't fill it
selinux: use sk blob accessor in socket permission helpers
Currently need_futex_hash_allocate_default() depends on strict pthread
semantics, abusing CLONE_THREAD. This breaks the non-concurrency
assumptions when doing the mm->futex_ref pcpu allocations, leading to
bugs[0] when sharing the mm in other ways; ie:
BUG: KASAN: slab-use-after-free in futex_hash_put
... where the +1 bias can end up on a percpu counter that mm->futex_ref
no longer points at.
Loosen the check to cover any CLONE_VM clone, except vfork(). Excluding
vfork keeps the existing paths untouched (no overhead), and we can't
race in the first place: either the parent is suspended and the child
runs alone, or mm->futex_ref is already allocated from an earlier
CLONE_VM.
Link: https://lore.kernel.org/all/CAL_bE8LsmCQ-FAtYDuwbJhOkt9p2wwYQwAbMh=PifC=VsiBM6A@mail.gmail.com/ [0]
Fixes: d9b05321e2 ("futex: Move futex_hash_free() back to __mmput()")
Reported-by: Yiming Qian <yimingqian591@gmail.com>
Signed-off-by: Davidlohr Bueso <dave@stgolabs.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull s390 fixes from Alexander Gordeev:
- Reject zero-length writes from userspace that corrupt Debug Facility
buffers
- Replace one s390 PCI maintainer
- Remove SCLP_OFB Kconfig option and enable the guarded code
unconditionally
- Replace incorrect use of phys_to_folio() to virt_to_folio() in
do_secure_storage_access()
* tag 's390-7.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/mm: Fix phys_to_folio() usage in do_secure_storage_access()
s390/sclp: Remove SCLP_OFB Kconfig option
MAINTAINERS: Replace one of the maintainers for s390/pci
s390/debug: Reject zero-length input in debug_input_flush_fn()
s390/debug: Reject zero-length input before trimming a newline
Pull smb server fixes from Steve French:
- Fix shutdown (stop sessions)
- Fix readdir unsupported info level
* tag 'v7.1-rc2-ksmbd-server-fixes' of git://git.samba.org/ksmbd:
ksmbd: rewrite stop_sessions() with restartable iteration
smb: server: handle readdir_info_level_struct_sz() error
Pull block fixes from Jens Axboe:
- MD pull request via Yu:
- Fix a raid5 UAF on IO across the reshape position
- Avoid failing RAID1/RAID10 devices for invalid IO errors
- Fix RAID10 divide-by-zero when far_copies is zero
- Restore bitmap grow through sysfs
- Use mddev_is_dm() instead of open-coding gendisk checks
- Use ATTRIBUTE_GROUPS() for md default sysfs attributes
- Replace open-coded wait loops with wait_event helpers
- NVMe pull request via Keith:
- Target data transfer size configuation (Aurelien)
- Enable P2P for RDMA (Shivaji Kant)
- TCP target updates (Maurizio, Alistair, Chaitanya, Shivam Kumar)
- TCP host updates (Alistair, Chaitanya)
- Authentication updates (Alistair, Daniel, Chris Leech)
- Multipath fixes (John Garry)
- New quirks (Alan Cui, Tao Jiang)
- Apple driver fix (Fedor Pchelkin)
- PCI admin doorbell update fix (Keith)
- Properly propagate CDROM read-only state to the block layer
* tag 'block-7.1-20260430' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux: (35 commits)
md: use ATTRIBUTE_GROUPS() for md default sysfs attributes
md: use mddev_is_dm() instead of open-coding gendisk checks
md/raid1: replace wait loop with wait_event_idle() in raid1_write_request()
md/md-bitmap: add a none backend for bitmap grow
md/md-bitmap: split bitmap sysfs groups
md: factor bitmap creation away from sysfs handling
md: use mddev_lock_nointr() in mddev_suspend_and_lock_nointr()
md: replace wait loop with wait_event() in md_handle_request()
md/raid10: fix divide-by-zero in setup_geo() with zero far_copies
md/raid1,raid10: don't fail devices for invalid IO errors
MAINTAINERS: Add Xiao Ni as md/raid reviewer
md/raid5: Fix UAF on IO across the reshape position
cdrom, scsi: sr: propagate read-only status to block layer via set_disk_ro()
nvme-auth: Hash DH shared secret to create session key
nvme-pci: fix missed admin queue sq doorbell write
nvme-auth: Include SC_C in RVAL controller hash
nvme-tcp: teardown circular locking fixes
nvmet-tcp: Don't clear tls_key when freeing sq
Revert "nvmet-tcp: Don't free SQ on authentication success"
nvme: skip trace completion for host path errors
...
Pull io_uring fixes from Jens Axboe:
- Remove dead struct io_buffer_list member
- Fix for incrementally consumed buffers with recvmsg multishot, which
requires a minimum value left in a buffer for any receive for the
headers. If there's still a bit of buffer left but it's smaller than
that value, then userspace will see a spurious -EFAULT returned in
the CQE
- Locking fix for the DEFER_TASKRUN retry list, which otherwise could
race with fallback cancelations. If the task is exiting with
task_work left in both the normal and retry list AND the exit cleanup
races with the task running task work, then entries could either be
doubly completed or lost
- Cap NAPI busy poll timeout to something sane, to avoid syzbot running
into excessive polling and triggering warnings around that
* tag 'io_uring-7.1-20260430' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux:
io_uring/tw: serialize ctx->retry_llist with ->uring_lock
io_uring/napi: cap busy_poll_to 10 msec
io_uring/kbuf: support min length left for incremental buffers
io_uring/kbuf: kill dead struct io_buffer_list 'nr_entries' member
Pull spi fixes from Mark Brown:
"There are a couple of nasty issues fixed here in the axiado and
rockchip drivers. We've also got more of the fixes from Johan here,
this time for the two Cadence drivers, plus a couple of other similar
fixes from John and Felix"
* tag 'spi-fix-v7.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: amlogic-spisg: initialize completion before requesting IRQ
spi: axiado: replace usleep_range() with udelay() in IRQ path
spi: cadence-quadspi: fix runtime pm and clock imbalance on unbind
spi: cadence-quadspi: fix unclocked access on unbind
spi: cadence-quadspi: fix clock imbalance on probe failure
spi: cadence-quadspi: fix runtime pm disable imbalance on probe failure
spi: cadence: fix clock imbalance on probe failure
spi: cadence: fix unclocked access on unbind
spi: rockchip: Drop unused and broken CR0 macros
spi: rockchip: Read ISR, not IMR, to detect cs-inactive IRQ
spi: rzv2h-rspi: Fix silent failure in clock setup error path
Commit 2e8a1acea8 ("arm64: signal: Improve POR_EL0 handling to
avoid uaccess failures") delayed the write to POR_EL0 in
rt_sigreturn to avoid spurious uaccess failures. This change however
relies on the poe_context frame record being present: on a system
supporting POE, calling sigreturn without a poe_context record now
results in writing arbitrary data from the kernel stack into POR_EL0.
Fix this by adding a __valid_fields member to struct
user_access_state, and zeroing the struct on allocation.
restore_poe_context() then indicates that the por_el0 field is valid
by setting the corresponding bit in __valid_fields, and
restore_user_access_state() only touches POR_EL0 if there is a valid
value to set it to. This is in line with how POR_EL0 was originally
handled; all frame records are currently optional, except
fpsimd_context.
To ensure that __valid_fields is kept in sync, fields (currently
just por_el0) are now accessed via accessors and prefixed with __ to
discourage direct access.
Fixes: 2e8a1acea8 ("arm64: signal: Improve POR_EL0 handling to avoid uaccess failures")
Cc: <stable@vger.kernel.org>
Reported-by: Will Deacon <will@kernel.org>
Signed-off-by: Kevin Brodsky <kevin.brodsky@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Pull regulator fix from Mark Brown:
"A fix from Arnd re-adding a dependency on gpiolib which was implicitly
pulled in via an OF specific route which got removed as part of a
cleanup"
* tag 'regulator-fix-v7.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: rpi-panel-attiny: add back GPIOLIB dependency
