Rev 1.5 microsoms include eMMC support on-board. Add a microsom include
file which can be used to add support for this.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There are two variants of the imx6qdl som: one with Broadcom Wi-Fi and
another with Texas Instruments Wi-Fi. The two Wi-Fi devices require
different DT bindings, so it's necessary to split out the Broadcom
specifics.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Jon and myself feel that "imx6qdl-microsom" is too generic a name for
SolidRun's microsom - some other manufacturer could have their own
microsom. Change the name to the shorter "imx6qdl-sr-som".
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As all SolidRun microsoms are fitted with an AR8035, it's pointless
having the ethernet support as a separate include file. Move the
AR8035 support into the main imx6qdl-microsom file.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
UDOO board has a possibility to disable most of imx6 SoC power supplies via
"EN_5V" signal, which is connected to "NANDF_D4" pad.
This reduces current consumption after shutdown from ~350 mA to ~40 mA and
prevents a SoC watchdog from starting it again on its own after the
watchdog timeout expires (previously it was not possible to shut down the
SoC permanently if its watchdog was ever enabled since it was still ticking
after the shutdown).
Unfortunately, this does not extinguish the "Power" LED (as it is powered
from an always-on voltage regulator).
To power the SoC up again press the power button (SW2, the one with a long
shaft).
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As explained in Documentation/devicetree/bindings/net/fsl-fec.txt the
phy-reset-gpios is active high only if the 'phy-reset-active-high' is
present.
As 'phy-reset-active-high' is not used here, fix the device tree
description by passing GPIO_ACTIVE_LOW flag.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
HDMI_TX_CEC_LINE pin is used for CEC, so pass it in the device tree.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On imx6qdl-sabreauto the HDMI DDC bus is connected to I2C2, so
pass the 'ddc-i2c-bus' property accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is not recommended to place regulators inside "simple-bus", so
move them out. The motivation for doing this is to make it easier to
adding new regulators.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently the imx pci driver fails to probe on i.MX6SX.
Fix the PCI representation so that the driver can be probed and
PCI devices can be detected.
Tested on a im6sx-sdb board:
00:00.0 Class 0604: 16c3:abcd
01:00.0 Class 0280: 8086:08b1
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
AC'97 interface RXD and TXC pins are only used as SoC inputs, let's disable
pad drivers for them so we will be protected if, for example, TCLKDIR is
set by mistake in AUDMUX and causes TXC pin to be configured as an output.
This also changes pull direction on these pins from pull-up to pull-down
to match what the board AC'97 CODEC chip (VT1613) has on these pins.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Commit a22950c888 (mmc: sdhci-of-esdhc: add quirk
SDHCI_QUIRK_BROKEN_TIMEOUT_VAL for ls1021a) added logic to the driver to
enable the broken timeout val quirk for ls1021a, but did not add the
corresponding compatible string to the device tree, so it didn't really
have any effect. Fix that.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ls1021a esdhc had been enabled in uboot,
but it had not been enabled it in kernel,
So set the esdhc's status to "okay".
Signed-off-by: yinbo.zhu <yinbo.zhu@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The two Ethernet switches have an AT24C512 each. This is a 64K device,
not 512 bytes as currently listed in the device tree.
Reported-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
"usb-nop-xceiv" is using the phy binding, but is missing #phy-cells
property. This is probably because the binding was the precursor to the phy
binding.
Fixes the following warning in i.MX dts files:
Warning (phys_property): Missing property '#phy-cells' in node ...
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This makes sure that the battery backed RTC is always the
primary one, regardless of the driver probe ordering.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This renames the audio device to "Front" in order to match the RDU2
naming, which makes it easier for a unified userspace to deal with
both boards.
Also rename the phandle for the headphone amplifier to more closely
resemble the RDU2 DTS.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There are 0 ohm resistors that allow selecting the EDID I2C port to
be I2C1 or I2C2.
On revd1 the 0 ohm resistors are populated in such a way that the I2C2
is used as DDC I2C bus, so fix it accordingly.
Reported-by: Luís Mendes <luis.p.mendes@gmail.com>
Suggested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx7s/imx7d has the ptp interrupt newly added as well.
For imx7, "int0" is the interrupt for queue 0 and ENET_MII
"int1" is for queue 1
"int2" is for queue 2
For imx6sx, "int0" handles all 3 queues and ENET_MII
And of course, the "pps" interrupt is for the PTP_CLOCK_PPS interrupts
This will help document what each interrupt does.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The following build warning is seen with W=1:
Warning (unit_address_vs_reg): Node /soc/aips@60000000/ethernet@63fec000/ethernet-phy@0 has a unit name, but no reg property
Fix this warning by adding reg property from such node and, consequently,
includes a mdio node into the fec node, with the 'address-cells' and
'size-cells' to avoid these other following warnings:
Warning (reg_format): "reg" property in /soc/aips@60000000/ethernet@63fec000/ethernet-phy@0 has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): Relying on default #address-cells value for /soc/aips@60000000/ethernet@63fec000/ethernet-phy@0
Warning (avoid_default_addr_size): Relying on default #size-cells value for /soc/aips@60000000/ethernet@63fec000/ethernet-phy@0
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Tested-by: Lothar Waßmann <LW@karo-electronics.de>
Acked-by: Lothar Waßmann <LW@karo-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add QSPI node support, and this function is disabled by default
This setting could be overwritten in board-level definitions
Signed-off-by: SZ Lin <sz.lin@moxa.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
sign_extend32 counts the sign bit parameter from 0, not from 1. So we
have to use "11" for 12th bit, not "12".
This mistake means we have not allowed negative op and cmp args since
commit 30d6e0a419 ("futex: Remove duplicated code and fix undefined
behaviour") till now.
Fixes: 30d6e0a419 ("futex: Remove duplicated code and fix undefined behaviour")
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Darren Hart <dvhart@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull btrfs fixes from David Sterba:
"This contains a few fixes (error handling, quota leak, FUA vs
nobarrier mount option).
There's one one worth mentioning separately - an off-by-one fix that
leads to overwriting first byte of an adjacent page with 0, out of
bounds of the memory allocated by an ioctl. This is under a privileged
part of the ioctl, can be triggerd in some subvolume layouts"
* tag 'for-4.15-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: Fix possible off-by-one in btrfs_search_path_in_tree
Btrfs: disable FUA if mounted with nobarrier
btrfs: fix missing error return in btrfs_drop_snapshot
btrfs: handle errors while updating refcounts in update_ref_for_cow
btrfs: Fix quota reservation leak on preallocated files
Pull ARM SoC fixes from Olof Johansson:
- A revert of all SCPI changes from the 4.15 merge window. They had
regressions on the Amlogic platforms, and the submaintainer isn't
around to fix these bugs due to vacation, etc. So we agreed to revert
and revisit in next release cycle.
- A series fixing a number of bugs for ARM CCN interconnect, around
module unload, smp_processor_id() in preemptable context, and fixing
some memory allocation failure checks.
- A handful of devicetree fixes for different platforms, fixing
warnings and errors that were previously ignored by the compiler.
- The usual set of mostly minor fixes for different platforms.
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (42 commits)
ARM64: dts: meson-gx: fix UART pclk clock name
ARM: omap2: hide omap3_save_secure_ram on non-OMAP3 builds
arm: dts: nspire: Add missing #phy-cells to usb-nop-xceiv
ARM: dts: Fix dm814x missing phy-cells property
ARM: dts: Fix elm interrupt compiler warning
bus: arm-ccn: fix module unloading Error: Removing state 147 which has instances left.
bus: arm-cci: Fix use of smp_processor_id() in preemptible context
bus: arm-ccn: Fix use of smp_processor_id() in preemptible context
bus: arm-ccn: Simplify code
bus: arm-ccn: Check memory allocation failure
bus: arm-ccn: constify attribute_group structures.
firmware: arm_scpi: Revert updates made during v4.15 merge window
arm: dts: marvell: Add missing #phy-cells to usb-nop-xceiv
arm64: dts: sort vendor subdirectories in Makefile alphabetically
meson-gx-socinfo: Fix package id parsing
ARM: meson: fix spelling mistake: "Couln't" -> "Couldn't"
ARM: dts: meson: fix the memory region of the GPIO interrupt controller
ARM: dts: meson: correct the sort order for the the gpio_intc node
MAINTAINERS: exclude other Socionext SoC DT files from ARM/UNIPHIER entry
arm64: dts: uniphier: remove unnecessary interrupt-parent
...
Pull KVM fixes from Radim Krčmář:
"ARM:
- A number of issues in the vgic discovered using SMATCH
- A bit one-off calculation in out stage base address mask (32-bit
and 64-bit)
- Fixes to single-step debugging instructions that trap for other
reasons such as MMMIO aborts
- Printing unavailable hyp mode as error
- Potential spinlock deadlock in the vgic
- Avoid calling vgic vcpu free more than once
- Broken bit calculation for big endian systems
s390:
- SPDX tags
- Fence storage key accesses from problem state
- Make sure that irq_state.flags is not used in the future
x86:
- Intercept port 0x80 accesses to prevent host instability (CVE)
- Use userspace FPU context for guest FPU (mainly an optimization
that fixes a double use of kernel FPU)
- Do not leak one page per module load
- Flush APIC page address cache from MMU invalidation notifiers"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (28 commits)
KVM: x86: fix APIC page invalidation
KVM: s390: Fix skey emulation permission check
KVM: s390: mark irq_state.flags as non-usable
KVM: s390: Remove redundant license text
KVM: s390: add SPDX identifiers to the remaining files
KVM: VMX: fix page leak in hardware_setup()
KVM: VMX: remove I/O port 0x80 bypass on Intel hosts
x86,kvm: remove KVM emulator get_fpu / put_fpu
x86,kvm: move qemu/guest FPU switching out to vcpu_run
KVM: arm/arm64: Fix broken GICH_ELRSR big endian conversion
KVM: arm/arm64: kvm_arch_destroy_vm cleanups
KVM: arm/arm64: Fix spinlock acquisition in vgic_set_owner
kvm: arm: don't treat unavailable HYP mode as an error
KVM: arm/arm64: Avoid attempting to load timer vgic state without a vgic
kvm: arm64: handle single-step of hyp emulated mmio instructions
kvm: arm64: handle single-step during SError exceptions
kvm: arm64: handle single-step of userspace mmio instructions
kvm: arm64: handle single-stepping trapped instructions
KVM: arm/arm64: debug: Introduce helper for single-step
arm: KVM: Fix VTTBR_BADDR_MASK BUG_ON off-by-one
...
Amlogic fixes for v4.15-rc
- GPIO interrupt fixes
- socinfo fix for GX series
- fix typo
* tag 'amlogic-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM64: dts: meson-gx: fix UART pclk clock name
meson-gx-socinfo: Fix package id parsing
ARM: meson: fix spelling mistake: "Couln't" -> "Couldn't"
ARM: dts: meson: fix the memory region of the GPIO interrupt controller
ARM: dts: meson: correct the sort order for the the gpio_intc node
Signed-off-by: Olof Johansson <olof@lixom.net>
bus: ARM CCN and CCI PMU driver fixes
This is a bunch of fixes CCN and (guest starring this time) CCI drivers.
* Check for potential of failed allocation for the driver name string
* Manage CPU ID properly at allocation (both CCN and CCI)
* Fix module unload warnings related to objects release order
* Small improvements like using allocating printfs and proper
attributes constification
The one fixing potential issues have been cc-ed to stable.
* tag 'ccn/fixes-for-4.15' of git://git.linaro.org/people/pawel.moll/linux:
bus: arm-ccn: fix module unloading Error: Removing state 147 which has instances left.
bus: arm-cci: Fix use of smp_processor_id() in preemptible context
bus: arm-ccn: Fix use of smp_processor_id() in preemptible context
bus: arm-ccn: Simplify code
bus: arm-ccn: Check memory allocation failure
bus: arm-ccn: constify attribute_group structures.
Signed-off-by: Olof Johansson <olof@lixom.net>
Two fixes for dts compiler warnings
These recently started showing up with better dtc checks being
introduced.
* tag 'omap-for-v4.15/fixes-dt-warnings' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix dm814x missing phy-cells property
ARM: dts: Fix elm interrupt compiler warning
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit 4675ff05de ("kmemcheck: rip it out") has removed the code but
for some reason SPDX header stayed in place. This looks like a rebase
mistake in the mmotm tree or the merge mistake. Let's drop those
leftovers as well.
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking fixes from David Miller:
1) CAN fixes from Martin Kelly (cancel URBs properly in all the CAN usb
drivers).
2) Revert returning -EEXIST from __dev_alloc_name() as this propagates
to userspace and broke some apps. From Johannes Berg.
3) Fix conn memory leaks and crashes in TIPC, from Jon Malloc and Cong
Wang.
4) Gianfar MAC can't do EEE so don't advertise it by default, from
Claudiu Manoil.
5) Relax strict netlink attribute validation, but emit a warning. From
David Ahern.
6) Fix regression in checksum offload of thunderx driver, from Florian
Westphal.
7) Fix UAPI bpf issues on s390, from Hendrik Brueckner.
8) New card support in iwlwifi, from Ihab Zhaika.
9) BBR congestion control bug fixes from Neal Cardwell.
10) Fix port stats in nfp driver, from Pieter Jansen van Vuuren.
11) Fix leaks in qualcomm rmnet, from Subash Abhinov Kasiviswanathan.
12) Fix DMA API handling in sh_eth driver, from Thomas Petazzoni.
13) Fix spurious netpoll warnings in bnxt_en, from Calvin Owens.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (67 commits)
net: mvpp2: fix the RSS table entry offset
tcp: evaluate packet losses upon RTT change
tcp: fix off-by-one bug in RACK
tcp: always evaluate losses in RACK upon undo
tcp: correctly test congestion state in RACK
bnxt_en: Fix sources of spurious netpoll warnings
tcp_bbr: reset long-term bandwidth sampling on loss recovery undo
tcp_bbr: reset full pipe detection on loss recovery undo
tcp_bbr: record "full bw reached" decision in new full_bw_reached bit
sfc: pass valid pointers from efx_enqueue_unwind
gianfar: Disable EEE autoneg by default
tcp: invalidate rate samples during SACK reneging
can: peak/pcie_fd: fix potential bug in restarting tx queue
can: usb_8dev: cancel urb on -EPIPE and -EPROTO
can: kvaser_usb: cancel urb on -EPIPE and -EPROTO
can: esd_usb2: cancel urb on -EPIPE and -EPROTO
can: ems_usb: cancel urb on -EPIPE and -EPROTO
can: mcba_usb: cancel urb on -EPROTO
usbnet: fix alignment for frames with no ethernet header
tcp: use current time in tcp_rcv_space_adjust()
...
Pull media fixes from Mauro Carvalho Chehab:
"A series of fixes for the media subsytem:
- The largest amount of fixes in this series is with regards to
comments that aren't kernel-doc, but start with "/**".
A new check added for 4.15 makes it to produce a *huge* amount of
new warnings (I'm compiling here with W=1). Most of the patches in
this series fix those.
No code changes - just comment changes at the source files
- rc: some fixed in order to better handle RC repetition codes
- v4l-async: use the v4l2_dev from the root notifier when matching
sub-devices
- v4l2-fwnode: Check subdev count after checking port
- ov 13858 and et8ek8: compilation fix with randconfigs
- usbtv: a trivial new USB ID addition
- dibusb-common: don't do DMA on stack on firmware load
- imx274: Fix error handling, add MAINTAINERS entry
- sir_ir: detect presence of port"
* tag 'media/v4.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (50 commits)
media: imx274: Fix error handling, add MAINTAINERS entry
media: v4l: async: use the v4l2_dev from the root notifier when matching sub-devices
media: v4l2-fwnode: Check subdev count after checking port
media: et8ek8: select V4L2_FWNODE
media: ov13858: Select V4L2_FWNODE
media: rc: partial revert of "media: rc: per-protocol repeat period"
media: dvb: i2c transfers over usb cannot be done from stack
media: dvb-frontends: complete kernel-doc markups
media: docs: add documentation for frontend attach info
media: dvb_frontends: fix kernel-doc macros
media: drivers: remove "/**" from non-kernel-doc comments
media: lm3560: add a missing kernel-doc parameter
media: rcar_jpu: fix two kernel-doc markups
media: vsp1: add a missing kernel-doc parameter
media: soc_camera: fix a kernel-doc markup
media: mt2063: fix some kernel-doc warnings
media: radio-wl1273: fix a parameter name at kernel-doc macro
media: s3c-camif: add missing description at s3c_camif_find_format()
media: mtk-vpu: add description for wdt fields at struct mtk_vpu
media: vdec: fix some kernel-doc warnings
...
Pull drm fixes from Dave Airlie:
"This pull is a bit larger than I'd like but a large bunch of it is
license fixes, AMD wanted to fix the licenses for a bunch of files
that were missing them,
Otherwise a bunch of TTM regression fix since the hugepage support,
some i915 and gvt fixes, a core connector free in a safe context fix,
and one bridge fix"
* tag 'drm-fixes-for-v4.15-rc3' of git://people.freedesktop.org/~airlied/linux: (26 commits)
drm/bridge: analogix dp: Fix runtime PM state in get_modes() callback
Revert "drm/i915: Display WA #1133 WaFbcSkipSegments:cnl, glk"
drm/vc4: Fix false positive WARN() backtrace on refcount_inc() usage
drm/i915: Call i915_gem_init_userptr() before taking struct_mutex
drm/exynos: remove unnecessary function declaration
drm/exynos: remove unnecessary descrptions
drm/exynos: gem: Drop NONCONTIG flag for buffers allocated without IOMMU
drm/exynos: Fix dma-buf import
drm/ttm: swap consecutive allocated pooled pages v4
drm: safely free connectors from connector_iter
drm/i915/gvt: set max priority for gvt context
drm/i915/gvt: Don't mark vgpu context as inactive when preempted
drm/i915/gvt: Limit read hw reg to active vgpu
drm/i915/gvt: Export intel_gvt_render_mmio_to_ring_id()
drm/i915/gvt: Emulate PCI expansion ROM base address register
drm/ttm: swap consecutive allocated cached pages v3
drm/ttm: roundup the shrink request to prevent skip huge pool
drm/ttm: add page order support in ttm_pages_put
drm/ttm: add set_pages_wb for handling page order more than zero
drm/ttm: add page order in page pool
...
Pull md fixes from Shaohua Li:
"Some MD fixes.
The notable one is a raid5-cache deadlock bug with dm-raid, others are
not significant"
* tag 'md/4.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
md/raid1/10: add missed blk plug
md: limit mdstat resync progress to max_sectors
md/r5cache: move mddev_lock() out of r5c_journal_mode_set()
md/raid5: correct degraded calculation in raid5_error
Pull DeviceTree fixes from Rob Herring:
"Another set of DT fixes:
- Fixes from overlay code rework. A trifecta of fixes to the locking,
an out of bounds access, and a memory leak in of_overlay_apply()
- Clean-up at25 eeprom binding document
- Remove leading '0x' in unit-addresses from binding docs"
* tag 'devicetree-fixes-for-4.15-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: overlay: Make node skipping in init_overlay_changeset() clearer
of: overlay: Fix out-of-bounds write in init_overlay_changeset()
of: overlay: Fix (un)locking in of_overlay_apply()
of: overlay: Fix memory leak in of_overlay_apply() error path
dt-bindings: eeprom: at25: Document device-specific compatible values
dt-bindings: eeprom: at25: Grammar s/are can/can/
dt-bindings: Remove leading 0x from bindings notation
of: overlay: Remove else after goto
of: Spelling s/changset/changeset/
of: unittest: Remove bogus overlay mutex release from overlay_data_add()
Pull virtio bugfixes from Michael Tsirkin:
"A couple of minor bugfixes"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_net: fix return value check in receive_mergeable()
virtio_mmio: add cleanup for virtio_mmio_remove
virtio_mmio: add cleanup for virtio_mmio_probe
Pull xen fixes from Juergen Gross:
"Just two small fixes for the new pvcalls frontend driver"
* tag 'for-linus-4.15-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/pvcalls: Fix a check in pvcalls_front_remove()
xen/pvcalls: check for xenbus_read() errors
Pull powerpc fixes from Michael Ellerman:
"One notable fix for kexec on Power9, where we were not clearing MMU
PID properly which sometimes leads to hangs. Finally debugged to a
root cause by Nick.
A revert of a patch which tried to rework our panic handling to get
more output on the console, but inadvertently broke reporting the
panic to the hypervisor, which apparently people care about.
Then a fix for an oops in the PMU code, and finally some s/%p/%px/ in
xmon.
Thanks to: David Gibson, Nicholas Piggin, Ravi Bangoria"
* tag 'powerpc-4.15-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/xmon: Don't print hashed pointers in xmon
powerpc/64s: Initialize ISAv3 MMU registers before setting partition table
Revert "powerpc: Do not call ppc_md.panic in fadump panic notifier"
powerpc/perf: Fix oops when grouping different pmu events
