Samsung DTS ARM64 changes for v4.20
1. Use graph between USB-PHY and MUIC.
2. Cleanup of SD card detect pin level.
* tag 'samsung-dt64-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: ARM: dts: exynos: Remove double SD card detect pin inversion on TM2
arm64: dts: exynos: Add OF graph between USB-PHY and MUIC
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Samsung DTS ARM changes for v4.20, second round
Add proper configuration for Odroid XU SD write-protect pin.
* tag 'samsung-dt-4.20-3' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Add pin configuration for SD write protect on Odroid XU
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Not all boards use two ethernet devices and/or use them in different
order. As almost all in-tree boards already define their own ethernet
aliases, remove them from the dtsi and add the aliases to the two boards,
that are missing their own definition.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
[dinguyen@kernel.org: rebased to latest dts changes]
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Add binding description for devices from
MT7623. Clock controller, iommu, JPEG Decoder
and SMI conotroller.
* tag 'v4.19-next-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
dt-bindings: mediatek: Add bindig for MT7623 IOMMU and SMI
dt-bindings: mediatek: Add JPEG Decoder binding for MT7623
dt-bindings: iommu: mediatek: Add binding for MT7623
dt-bindings: clock: mediatek: add support for MT7623
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
mvebu dt for 4.20 (part 2)
Auto-detect nand ECC on the armada-385 based board db-88f6820-amc
instead of hard coded them in the device tree.
* tag 'mvebu-dt-4.20-2' of git://git.infradead.org/linux-mvebu:
ARM: dts: mvebu: armada-385-db-88f6820-amc: auto-detect nand ECC properites
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
mvebu dt64 for 4.20 (part 2)
- Add System Error Interrupt support to Armada SoCs (7K/8K)
- Add CPU idle support on Armada 8K
* tag 'mvebu-dt64-4.20-2' of git://git.infradead.org/linux-mvebu:
arm64: dts: clearfog-gt-8k: add PCIe slot description
arm64: dts: marvell: add CP110 ICU SEI subnode
arm64: dts: marvell: use new bindings for CP110 interrupts
arm64: dts: marvell: add AP806 SEI subnode
arm64: dts: marvell: add CPU Idle power state support on Armada 7K/8K
arm64: dts: marvell: Add node labels for the cpus
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This board has a Micron MT29F8G08ABACAWP chip which requires a ECC
strength of 8/512. Rather than hard coding any particular strength the
the nand controller auto-detect the ECC strength based on the ONFI data.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
DaVinci DT updates for v4.20
----------------------------
- A non-critical fix to reduce errors on A/DC on Lego Mindstorms EV3
- Support for GPIO expander on DA850 EVM
* tag 'davinci-for-v4.20/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850-lego-ev3: slow down A/DC as much as possible
ARM: dts: da850-evm: Enable tca6416 on baseboard
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Nodes for the newly support rk3188 display controller, a fix for a new
dtc warning, gpio setting for the sdmmc regulator on radxarock and a
new board the "S" variant of the rk3288-based Tinker board, that sports
an added emmc.
* tag 'v4.20-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add rk3288-based Tinker board S
ARM: dts: rockchip: move shared tinker-board nodes to a common dtsi
ARM: dts: rockchip: explicitly set vcc_sd0 pin to gpio on rk3188-radxarock
ARM: dts: rockchip: Fix erroneous SPI bus dtc warnings on rk3036
ARM: dts: rockchip: add rk3188 lcd controller nodes
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Due to the electrical design of the A/DC circuits on LEGO MINDSTORMS EV3,
if we are reading analog values as fast as possible (i.e. using DMA to
service the SPI) the A/DC chip will read incorrect values - as much as
0.1V off when the SPI is running at 10MHz. (This has to do with the
capacitor charge time when channels are muxed in the A/DC.)
This patch slows down the SPI as much as possible (if CPU is at 456MHz,
SPI runs at 1/2 of that, so 228MHz and has a max prescalar of 256, so
we could get ~891kHz, but we're just rounding it to 1MHz). We also use
the max allowable value for WDELAY to slow things down even more.
These changes reduce the error of the analog values to about 5mV, which
is tolerable.
Commits a3762b13a5 ("spi: spi-davinci: Add support for SPI_CS_WORD")
and e2540da86e ("iio: adc: ti-ads7950: use SPI_CS_WORD to reduce
CPU usage") introduce changes that allow DMA transfers to be used, so
this slow down is needed now.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
There is a GPIO expander on both the UI board as well as the
baseboard. This patch enables the second tca6416 and identifies
it as being on the baseboard using _bb as the suffix.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Some additional new boards, the rk3399-based RockPro64 from Pine64, as well
as the Vamrs Rock960. Another big feature is display support including hdmi
and the Innosilicon hdmiphy on the rk3328, right now enabled on the rock64.
The rock64 also got its spi-nor and spdif enabled. On the px30 we can see
dwc2-based usb support now and finally some misc fixes, like for a new dtc
warning, missing address and size cells and microSD fix on sapphire.
* tag 'v4.20-rockchip-dts64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: enable display nodes on rk3328-rock64
arm64: dts: rockchip: add rk3328 display nodes
arm64: dts: rockchip: add Innosilicon hdmi phy node to rk3328
arm64: dts: rockchip: add missing address and size cells for rk3399 mipi dsi
arm64: dts: rockchip: Enable SPI NOR flash on Rock64
arm64: dts: rockchip: add initial dts support for Rockpro64
arm64: dts: rockchip: enable dwc2-based otg controller on px30-evb
arm64: dts: rockchip: add dwc2 otg controller on px30
dt-bindings: usb: dwc2: add description for px30
arm64: dts: rockchip: Enable SD card detection for Rock960 boards
arm64: dts: rockchip: Add support for Rock960 board
dt-bindings: arm: rockchip: Add binding for Rock960 board
arm64: dts: rockchip: Split out common nodes for Rock960 based boards
arm64: dts: rockchip: add spdif sound node for rock64
arm64: dts: rockchip: Fix microSD in rk3399 sapphire board
arm64: dts: rockchip: Fix I2C bus unit-address error on rk3399-puma-haikou
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
More devicetree changes for omap variants
There's a patch for previously merged dts changes to remove the last
remaining use of legacy phy_id property.
For dra7, we have a non-urgent PCIe dts fix, enable a PCIe errata for
unaligned access.
For omap5, we enable omap5 USB OTG mode for DWC3 controller.
And we add support for am335x based Moxa UC-2100 series of industrial
computers.
* tag 'omap-for-v4.20/dt-signed-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x: Replace remaining legacy phy_id with phy-handle
ARM: dts: am335x: add support for Moxa UC-2101 open platform
ARM: dts: am335x: add common file for UC-2100 series
ARM: dts: omap5: enable OTG role for DWC3 controller
ARM: dts: dra7: Enable workaround for errata i870 in PCIe host mode
ARM: dts: dra7: Fix up unaligned access setting for PCIe EP
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add USB3 controller nodes including usb-core, resets, regulator, ss-phy
and hs-phy. This supports for LD20, PXs3 and the boards. This includes
additional efuse nodes for obtaining PHY trimming values.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add USB3 controller nodes including usb-core, resets, regulator, ss-phy
and hs-phy. This supports for Pro4, PXs2 and the boards.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
While it is possible to rework the s400 board to solder an eMMC on it,
it is not the default option and most boards are fitted with a NAND
instead.
Let's disable the emmc device by default to reflect this. The board
equipped with an eMMC will just have to alter the DT in the
bootloader, like we do for the reserved memory regions.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
eMMC pwrseq is defined in the s400 dts but not used in the emmc node.
This is probably just a copy/paste error
Fixes: 221cf34bac ("ARM64: dts: meson-axg: enable the eMMC controller")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This adds support for the PCIe interface on the CON4 mini-PCIe
connector.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Create an ICU subnode for the NSR interrupts. This subnode becomes the
CP110 interrupt parent, removing the need for the ICU_GRP_NSR parameter.
Move all DT110 nodes to use these new bindings.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Add SD controller nodes for LD20 and PXs3.
LD20 does not support the UHS mode, while PXs3 supports it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add SD controller nodes for LD4, Pro4, sLD8, Pro5, and PXs2.
This is also used as an eMMC controller for LD4, Pro4, and sLD8.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add the System Error Interrupt node, representing an IRQ chip which is
part of the GIC. The SEI node aggregates interrupts from the AP through
wired interrupts, and from the CPs through MSIs.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This patch adds CPU deep Idle and Cluster deep Idle states BUT it defines
the idle state for each cpu (defined under cpu-idle-states parameter)
only for the quad version therefore it does NOT activate CPU Idle
capability for the other version.
[gregory: extract from a larger patch]
Signed-off-by: orenbh <orenbh@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Aligned with what we have done for the others nodes. It will also allow
to easily modify the cpu configuration at board (or sub-SoC) level.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Devicetree changes for omap variants
This branch contains a series of improvments for omap3-gta04 phone,
and a series of clean-up for am335x to remove the deprecated phy_id
property.
The rest is to configure am57xx-idk boards for leds, load trigger,
and smps, am3517-evm audio configuration, beaglebone hdmi cec support,
coresight binding update, and fixes for i2c and spi warnings.
* tag 'omap-for-v4.20/dt-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (70 commits)
ARM: dts: add omap3-gta04a5one to Makefile
ARM: dts: omap3-gta04: add pulldown/up settings for twl4030 gpio
ARM: dts: am335x-boneblack: add cec support
ARM: dts: am3517-evm: Add support for UI board and Audio
ARM: dts: gta04: add serial console wakeup irq
ARM: dts: am57xx-idk-common: Hook smps12 regulator as cpu vdd-supply
ARM: dts: omap: Update coresight bindings for hardware ports
ARM: dts: ti: Fix SPI and I2C bus warnings
ARM: dts: dra62x-j5eco-evm: get rid of phy_id property
ARM: dts: dm8148-t410: get rid of phy_id property
ARM: dts: dm8148-evm: get rid of phy_id property
ARM: dts: am57xx-cl-som-am57x: get rid of phy_id property
ARM: dts: am57xx-idk-common: get rid of phy_id property
ARM: dts: dra7-evm: get rid of phy_id property
ARM: dts: dra71-evm: get rid of phy_id property
ARM: dts: dra72-evm-revc: get rid of phy_id property
ARM: dts: dra72-evm: get rid of phy_id property
ARM: dts: dra76-evm: get rid of phy_id property
ARM: dts: am437x-cm-t43: get rid of phy_id property
ARM: dts: am437x-gp-evm: get rid of phy_id property
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
mvebu dt for 4.20 (part 1)
- updates the armada-xp-98dx3236 SoC and related boards to use the new
style dts bindings for nand
- add db-88f6820-amc board: plugin card for some of Marvell's switch
development kits
- fix SPI and I2C bus warnings coming with the new checks in dtc
- add new compatible string "marvell,prestera" to the armada-xp-98dx*
- fix sdhci supply property name on the clearfog (the '-supply' suffix
was missing)
* tag 'mvebu-dt-4.20-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: clearfog: fix sdhci supply property name
ARM: dts: mvebu: add "marvell,prestera" to PP nodes
ARM: dts: marvell: Fix SPI and I2C bus warnings
ARM: dts: mvebu: Add device tree for db-88f6820-amc board
ARM: dts: mvebu: db-xc3-24g4: use new style nand binding
ARM: dts: mvebu: db-dxbc2: use new style nand binding
ARM: dts: mvebu: 98dx3236: Rename nand controller node
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Freescale arm64 device tree update for 4.20:
- Add the second Dual UART device for LS208xA SoCs.
- Add necessary big-endian property for NOR device on LS104xA based
boards, remove unneeded big-endian property from IFC controller.
- DTC has new checks for I2C and SPI buses to land into 4.20. A patch
from Rob to fix the bus node names and warnings in unit-addresses.
* tag 'imx-dt64-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: fsl: Fix I2C and SPI bus warnings
arm64: dts: ls208xa: add second duart
arm64: dts: fsl: remove big-endian field from IFC controller
arm64: dts: Add big-endian in nor node for ls104xa
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
i.MX device tree update for 4.20:
- New board support: Engicam's i.Core MX6 CPU module v1.5; ConnectCore
6UL Single Board Computer (SBC) Pro; i.MX6 ULZ based EVK board.
- Add Add SFF interface support for vf610-zii board.
- Disable unneeded devices like VPU and internal watchdog for imx51-zii
boards.
- Add 'no-sdio' and 'no-sd' property for vf610-zii-cfu1 board.
- Improve i.MX6 SLL GPIO support by adding gpio-ranges property and
clocks information.
- Update iomux header for i.MX7 Solo and i.MX6 ULL.
- Enable GPIO buttons as wakeup source for imx7d-sdb and imx6sx-sdb.
- Add GPIO keys and egalax touch screen support for imx6qdl-sabreauto.
- Switch to use SPDX-License-Identifier for more boards - vf610-twr,
imx7s-warp, Engicam boards.
- Add device tree bindings of 'fsl,pmic-stby-poweroff' property and add
the support for i.MX6 RIoTboard.
- DTC has new checks for SPI buses which will be landed on 4.20.
A patch from Rob to fix those 100+ warnings on i.MX boards. (Thanks!)
- Switch i.MX7 device tree to use updated coresight binding for
hardware ports.
- Misc small or random update and cleanup.
* tag 'imx-dt-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (50 commits)
ARM: dts: imx: add i.mx6ulz and i.mx6ulz 14x14 evk support
dt-bindings: arm: add compatible for i.MX6ULZ 14x14 EVK board
ARM: dts: imx53-ppd: Remove 'num-chipselects' property
ARM: dts: vf610-twr: Switch to SPDX identifier
ARM: dts: vf: Switch to SPDX identifier
ARM: dts: imx6qdl-zii-rdu2: Disable the internal RTC
ARM: dts: imx51-zii-rdu1: Fix the rtc compatible string
ARM: dts: imx6ul: use nvmem-cells for cpu speed grading
ARM: dts: imx: Fix SPI bus warnings
ARM: dts: imx7: Update coresight binding for hardware ports
ARM: dts: vf610-zii-cfu1: Pass the 'no-sd' property
ARM: dts: vf610-zii-cfu1: Pass the 'no-sdio' property
ARM: dts: imx51-zii-scu2-mezz: Disable the internal watchdog
ARM: dts: imx51-zii-scu2-mezz: Disable VPU
ARM: dts: imx51-zii-scu3-esb: Disable VPU
ARM: dts: imx51: Add label for VPU node
ARM: dts: imx6ull: update vdd_soc voltage for 900MHz operating point
ARM: dts: imx6ul: Add DTS for ConnectCore 6UL SBC Pro
ARM: dts: imx6: RIoTboard provide standby on power off option
dt-bindings: imx6q-clock: add new fsl,pmic-stby-poweroff property
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Qualcomm Device Tree Changes for v4.20
* Fix IRQ constants usage on MSM8974
* Add led, gpio-button, sdcc, and pcie nodes for IPQ8064
* Move/cleanup common nodes for IPQ8064
* Add i2c sensor nodes for MSM8974 Hammerhead
* Fixes for SAW, kpss, opp, pci range, and space/tab on IPQ4019
* Update coresight bindings
* tag 'qcom-dts-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
ARM: dts: qcom: Update coresight bindings for hardware ports
ARM: dts: qcom-msm8974: change invalid flag IRQ NONE to valid value
ARM: dts: qcom: ipq4019: fix space vs tab indenting inside qcom-ipq4019.dtsi
ARM: dts: qcom: ipq4019: fix PCI range
ARM: dts: qcom: ipq4019: fix cpu0's qcom,saw2 reg value
ARM: dts: qcom: ipq4019: add cpu operating points for cpufreq support
ARM: dts: qcom: ipq4019: use v2 of the kpss bringup mechanism
ARM: dts: qcom: msm8974-hammerhead: add device tree bindings for ALS / proximity
ARM: dts: qcom: msm8974-hammerhead: add device tree bindings for mpu6515
ARM: dts: qcom: Add led and gpio-button nodes to ipq8064 boards
ARM: dts: qcom: Move common nodes to ipq8064-v.1.0.dtsi
ARM: dts: qcom: Add sdcc nodes for ipq8064
ARM: dts: qcom: Add pcie nodes for ipq8064
ARM: dts: qcom-msm8974: change invalid flag IRQ NONE to valid value
ARM: dts: qcom-msm8974: use named constant for interrupt flag NONE
ARM: dts: qcom-msm8974: use named constant for interrupt flag LEVEL HIGH
ARM: dts: qcom-msm8974: use named constant for interrupt flag EDGE RISING
ARM: dts: qcom-msm8974: use named constant for interrupt type GIC_SPI
ARM: dts: qcom-msm8974: use named constant for interrupt type GIC_PPI
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
