Do read-modify-write so that we re-use the characterized reset value as
specified in TRM [1] to program calibration wait time which defines number
of cycles to wait for after startup state machine is in bandgap enable
state.
This fixes PLL lock timeout error faced while using RPi DSI Panel on TI's
AM62L and J721E SoC since earlier calibration wait time was getting
overwritten to zero value thus failing the PLL to lockup and causing
timeout.
[1] AM62P TRM (Section 14.8.6.3.2.1.1 DPHY_TX_DPHYTX_CMN0_CMN_DIG_TBIT2):
Link: https://www.ti.com/lit/pdf/spruj83
Cc: stable@vger.kernel.org
Fixes: 7a343c8bf4 ("phy: Add Cadence D-PHY support")
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Tested-by: Harikrishna Shenoy <h-shenoy@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://lore.kernel.org/r/20250704125915.1224738-3-devarsht@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
PLL lockup and O_CMN_READY assertion can only happen after common state
machine gets enabled by programming DPHY_CMN_SSM register, but driver was
polling them before the common state machine was enabled which is
incorrect. This is as per the DPHY initialization sequence as mentioned in
J721E TRM [1] at section "12.7.2.4.1.2.1 Start-up Sequence Timing Diagram".
It shows O_CMN_READY polling at the end after common configuration pin
setup where the common configuration pin setup step enables state machine
as referenced in "Table 12-1533. Common Configuration-Related Setup
mentions state machine"
To fix this :
- Add new function callbacks for polling on PLL lock and O_CMN_READY
assertion.
- As state machine and clocks get enabled in power_on callback only, move
the clock related programming part from configure callback to power_on
callback and poll for the PLL lockup and O_CMN_READY assertion after state
machine gets enabled.
- The configure callback only saves the PLL configuration received from the
client driver which will be applied later on in power_on callback.
- Add checks to ensure configure is called before power_on and state
machine is in disabled state before power_on callback is called.
- Disable state machine in power_off so that client driver can re-configure
the PLL by following up a power_off, configure, power_on sequence.
[1]: https://www.ti.com/lit/zip/spruil1
Cc: stable@vger.kernel.org
Fixes: 7a343c8bf4 ("phy: Add Cadence D-PHY support")
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Tested-by: Harikrishna Shenoy <h-shenoy@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://lore.kernel.org/r/20250704125915.1224738-2-devarsht@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The existing ID detection logic returned false when both IDDIG and
VBUSVALID were set, which caused incorrect role determination in some
cases. The condition:
!(device && !vbus_valid)
did not properly reflect the intended relationship between IDDIG and
VBUSVALID signals.
Update the logic to:
return vbus_valid ? device : !device;
This ensures that when VBUS is valid, the role follows the IDDIG value,
and when VBUS is not valid, the role is inverted, matching the expected
OTG behavior.
Fixes: b725741f1c ("phy: renesas: rcar-gen3-usb2: Add support for RZ/T2H SoC")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250821155957.1088337-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add phy and pll regulator load voting support for all supported
platforms by introducing dedicated regulator bulk data arrays
with their load values.
This ensures stable operation and proper power management for these
platforms where regulators are shared between the QMP UFS PHY and
other IP blocks by setting appropriate regulator load currents during
PHY operations.
Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://lore.kernel.org/r/20250830070353.2694-3-nitin.rawat@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
On certain SoCs, power regulators are shared between the QMP UFS PHY
and other IP blocks. To ensure proper operation, the regulator
framework must be informed of the UFS PHY's load requirements.
This is essential because the regulator's operating mode—whether Low
Power or High Power—depends on the maximum expected load at any given
time, which the regulator driver needs to manage accordingly.
To support this, replace devm_regulator_bulk_get() with
devm_regulator_bulk_get_const() and inline the qmp_ufs_vreg_init()
function. additionally replace the array of regulator names with a
bulk regulator data structure, and utilize the init_load_uA field
provided by the regulator framework. This ensures that
regulator_set_load() is automatically invoked before the
first enable operation.
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Link: https://lore.kernel.org/r/20250830070353.2694-2-nitin.rawat@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add initial support for the Renesas RZ/T2H SoC to the R-Car Gen3 USB2 PHY
driver. The RZ/T2H SoC requires configuration of additional
hardware-specific bits for proper VBUS level control and OTG operation.
Introduce the `vblvl_ctrl` flag in the SoC-specific driver data to enable
handling of VBUS level selection logic using `VBCTRL.VBLVL` bits. This is
required for managing the VBUS status detection and drive logic based on
SoC-specific needs.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250808215209.3692744-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Store the SoC-specific driver data pointer (struct rcar_gen3_phy_drv_data)
directly in struct rcar_gen3_chan instead of copying individual flags into
separate channel members.
Obtain the drvdata with of_device_get_match_data() in probe and assign it
to channel->phy_data. Update all call sites to reference
`channel->phy_data->*` for SoC-specific behaviour (for example no_adp_ctrl
and utmi_ctrl). Remove the redundant soc_no_adp_ctrl and utmi_ctrl fields
from struct rcar_gen3_chan.
This simplifies the probe path, reduces duplication, and makes it easier
to extend the driver with additional platform-specific fields in the
future.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250808215209.3692744-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Register a typec mux in order to change the PHY mode on the Type-C
mux events depending on the mode and the svid when in Altmode setup.
The DisplayPort phy should be left enabled if is still powered on
by the DRM DisplayPort controller, so bail out until the DisplayPort
PHY is not powered off.
The Type-C Mode/SVID only changes on plug/unplug, and USB SAFE states
will be set in between of USB-Only, Combo and DisplayPort Only so
this will leave enough time to the DRM DisplayPort controller to
turn of the DisplayPort PHY.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
[konrad: renaming, rewording, bug fixes]
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on Lenovo Thinkpad T14S
Link: https://lore.kernel.org/r/20250807-topic-4ln_dp_respin-v4-5-43272d6eca92@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The QMP USB3/DP Combo PHY can work in 3 modes:
- DisplayPort Only
- USB3 Only
- USB3 + DisplayPort Combo mode
In order to switch between those modes, the PHY needs to receive
Type-C events, allow marking to the phy with the mode-switch
property in order to allow the PHY to Type-C events.
Reference usb-switch.yaml as a simpler way to allow the mode-switch
property instead of duplicating the property definition.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on Lenovo Thinkpad T14S
Link: https://lore.kernel.org/r/20250807-topic-4ln_dp_respin-v4-1-43272d6eca92@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Replace comma between expressions with semicolons.
Using a ',' in place of a ';' can have unintended side effects.
Although that is not the case here, it is seems best to use ';'
unless ',' is intended.
Found by inspection.
No functional change intended.
Compile tested only.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Link: https://lore.kernel.org/r/20250814013943.2905307-1-nichen@iscas.ac.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
So far we set a number of expected Allwinner USB PHY instances for any
given compatible string, and would fail if we do not find every PHY
described properly in the DT (missing reset/PMU/clocks).
This is somewhat redundant, as the DT only describes the resources for
the implemented PHYs, but goes in line with being strict about firmware
descriptions, and rather fixing things in the driver code, based on the
compatible string.
However this causes issues when we make a mistake, like we did recently
on the A523: there are actually three USB PHYs, not two, as we assumed.
Changing the number in the driver and the compatible string would cause
all kinds of compatibility issues, both with older and newer DTs.
To avoid problems with newer kernels and older or newer DTs, we can change
the driver code to deduce the number of PHY instances from what's
described in the DT. This has the added advantage of not requiring new
compatible strings for new SoCs when just the number of PHYs change, which
already happened and might occur again in the future.
Drop the num_phys member from the config struct, and remove the fixed
number of PHYs from each SoC's config description. Then enumerate the
usb<x>_reset properties for all of the maximum four PHY instances, and
just stop once we cannot find such a property anymore.
The binding describes the reset property as mandatory for each PHY
instance, and each DT in the kernel tree matches exactly the num_phys
value in the current driver code, so we can rely on that.
Apart from being more future proof, this will solve the A523 mishap:
Older DTs would just describe two PHYs, whereas newer ones would feature
all three of them. In any case we would get a valid number, matching the
other nodes in the DT. Older kernels would always enumerate two PHYs,
which at least does not cause any regressions.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20250819001522.13011-1-andre.przywara@arm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Document the FS Differential TX Output Resistance Tuning value found on
the eUSB2 repeater on Qualcomm PMICs. The tuning values have special
meanings, being different offsets of the resistance to the default value
in Ohms but the exact meaning is not relevant here, as the correct
tuning is determined by hardware engineers to make sure the electrical
properties are as expected.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20250709-sm7635-eusb-repeater-v2-1-b6eff075c097@fairphone.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
