On EV6 and later the hardware records exception status bits in the FPCR
before delivering a software completion trap, and those bits can be wrong
for the instruction that trapped. Converting a double that is exactly
representable as a subnormal float sets FPCR_UNF even though the result
is exact, and an underflow trap additionally sets FPCR_INE even when the
emulated operation turns out to be exact.
alpha_fp_emul() only wrote the FPCR when soft-fp raised an exception, so
whenever it determined that the instruction was exact the fabricated bits
stayed in the FPCR and were reported to user space by fetestexcept().
Pass the exception summary register down from do_entArith() so the
handler can tell which exceptions the hardware attributed to the trapping
instruction, and always write the FPCR. Clear the exceptions that the
trap reported but that soft-fp did not raise. EXC_SUM reports only the
underflow or overflow when the hardware also set INE, so treat INE as a
candidate in that case, and treat a trap with no reported exception as a
denormal operand trap, for which the hardware can fabricate INE and UNF
as well. Bits that software has already confirmed in ieee_state belong
to this or an earlier instruction and are never cleared.
The imprecise path passes no summary. There the trap was taken somewhere
in the trap shadow, so EXC_SUM is not attribution for the instruction
being re-executed -- and only EV6, which traps precisely and so never
takes that path, has fabricated bits to clear. For the same reason the
clearing is guarded by implver(), matching swcr_update_status().
On an UP1500 (EV68) this takes the glibc math testsuite from 831 failures
to 28, the remainder being unrelated to exception status.
This belongs with the preceding fix to ieee_swcr_to_fpcr(), and should
not be backported without it -- nor it without this. That fix stops
FPCR_DNOD being set unconditionally, so denormal operand traps start
firing again. Those traps very often find an exact result, which is
precisely the case where the old code left the FPCR unwritten and the
fabricated bits visible. Applied alone it would make spurious exception
flags more common, not less.
One case cannot be resolved here: an inexact instruction without the
software completion suffix never traps, so its INE reaches the FPCR
without being recorded anywhere else. Such a bit is indistinguishable
from an INE the hardware fabricated for a trapping instruction, and is
lost if an underflow or overflow trap with an exact result follows it.
The FPCR is the only record of those instructions and it carries no
attribution.
The bug predates the git history, so there is no commit to reference in a
Fixes tag.
Cc: stable@vger.kernel.org # 5.15+
Signed-off-by: Matt Turner <mattst88@gmail.com>
Reviewed-by: Magnus Lindholm <linmag7@gmail.com>
Tested-by: Magnus Lindholm <linmag7@gmail.com>
Link: https://lore.kernel.org/r/20260803-alpha-fp-exceptions-v1-2-c99d75608e60@gmail.com
Signed-off-by: Magnus Lindholm <linmag7@gmail.com>
ieee_swcr_to_fpcr() converts the software IEEE trap-enable and status
bits kept in thread_info.ieee_state into the hardware FPCR format. It
contained:
fp |= (~sw & IEEE_TRAP_ENABLE_DNO) << 41;
FPCR_DNOD (bit 47) disables denormal operand traps: with it set the
hardware handles a denormal operand itself, treating it as zero, instead
of trapping for software completion. The intent was to set DNOD when the
user has not asked for SIGFPE on denormal operands, but
IEEE_TRAP_ENABLE_DNO is clear by default, so ieee_swcr_to_fpcr(0) always
set DNOD.
Instructions built with the software completion suffix therefore never
trapped on a denormal operand. The hardware silently substituted zero
and produced wrong results, affecting every program compiled with -mieee
and default FPU settings, glibc included.
Set FPCR_DNOD only when IEEE_MAP_DMZ is requested, which is exactly the
case where flushing denormal inputs to zero is what the user asked for.
DNOD then encodes MAP_DMZ, which ieee_fpcr_to_swcr() already recovers
from FPCR_DNZ, so drop its attempt to recover IEEE_TRAP_ENABLE_DNO from
DNOD; the DNO trap enable lives solely in ieee_state.
Both functions are in a uapi header, so the encoding change is visible to
userspace, but nothing outside the kernel is known to depend on DNOD
carrying the DNO trap enable, and the kernel is the only writer of the
FPCR.
This must not be backported on its own. Re-enabling denormal operand
traps exposes a second bug, fixed in the following patch: those traps
usually find an exact result, and for an exact result the emulator did
not write the FPCR back, leaving hardware-fabricated exception bits
visible to user space. Taken alone this change would make spurious
exception flags more common.
The bug predates the git history, so there is no commit to reference in a
Fixes tag.
Cc: stable@vger.kernel.org # 5.15+
Signed-off-by: Matt Turner <mattst88@gmail.com>
Reviewed-by: Magnus Lindholm <linmag7@gmail.com>
Tested-by: Magnus Lindholm <linmag7@gmail.com>
Link: https://lore.kernel.org/r/20260803-alpha-fp-exceptions-v1-1-c99d75608e60@gmail.com
Signed-off-by: Magnus Lindholm <linmag7@gmail.com>
Alpha masks interrupts through the PAL IPL state, so lockdep cannot infer
hardirq state transitions from generic code alone. Add explicit
hardirq on/off annotations to the low-level entry and return paths so
lockdep's IRQ state follows the hardware IPL state.
Annotate the PAL IPL transitions and the shared return-to-user/kernel
paths where interrupts become enabled or disabled. With the preceding
irqflags, raw-lock, sysfs, and ftrace return-address preparations in
place, select LOCKDEP_SUPPORT and TRACE_IRQFLAGS_SUPPORT for Alpha.
This keeps CONFIG_PROVE_LOCKING usable on Alpha instead of disabling
debug_locks due to IRQ-state mismatches.
Reviewed-by: Matt Turner <mattst88@gmail.com>
Tested-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Magnus Lindholm <linmag7@gmail.com>
Link: https://lore.kernel.org/r/20260706170019.2941459-7-linmag7@gmail.com
Signed-off-by: Magnus Lindholm <linmag7@gmail.com>
Some Alpha platform locks are used as low-level hardware serialization
locks in interrupt-controller and chipset access paths. These paths can
run while IRQ state is being changed or while lockdep is tracking that
state, so regular spinlock instrumentation is not appropriate once
lockdep is enabled.
Convert the affected Tsunami and Rawhide platform locks to
raw_spinlock_t. This keeps the locks as simple hardware serialization
locks and avoids lockdep recursion or IRQ-state mismatches when
CONFIG_PROVE_LOCKING is enabled.
This is a preparatory change for enabling lockdep hardirq state tracking
on Alpha.
Reviewed-by: Matt Turner <mattst88@gmail.com>
Tested-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Magnus Lindholm <linmag7@gmail.com>
Link: https://lore.kernel.org/r/20260706170019.2941459-6-linmag7@gmail.com
Signed-off-by: Magnus Lindholm <linmag7@gmail.com>
Lockdep uses ftrace_return_address() to report useful call sites for
lock acquisition and IRQ-state tracking diagnostics. Provide the Alpha
architecture hook using the compiler return-address builtin when frame
pointers are available.
Return zero when frame pointers are disabled, matching the existing
fallback behavior of architectures that cannot provide a reliable return
address.
This is a preparatory change for enabling lockdep support on Alpha.
Reviewed-by: Matt Turner <mattst88@gmail.com>
Tested-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Magnus Lindholm <linmag7@gmail.com>
Link: https://lore.kernel.org/r/20260706170019.2941459-5-linmag7@gmail.com
Signed-off-by: Magnus Lindholm <linmag7@gmail.com>
Alpha interrupt masking is controlled by the PAL IPL value, not by the
full processor status word. Make arch_local_save_flags() return the
current IPL directly, and make arch_local_irq_restore() and
arch_irqs_disabled_flags() treat their argument as IPL state.
Mask the low IPL bits in the restore and test helpers so callers which
still pass a saved PS value continue to behave as expected.
This prepares the irqflags helpers for lockdep IRQ-state tracking, where
the saved flags value is used to determine whether hard IRQs are enabled
or disabled.
Reviewed-by: Matt Turner <mattst88@gmail.com>
Tested-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Magnus Lindholm <linmag7@gmail.com>
Link: https://lore.kernel.org/r/20260706170019.2941459-4-linmag7@gmail.com
Signed-off-by: Magnus Lindholm <linmag7@gmail.com>
Implement arch_stack_walk() for Alpha using a simple kernel
stack scanning walker. Start from regs+1 for current tasks
to skip pt_regs and use pcb.ksp for blocked tasks. Filter
candidates with __kernel_text_address() and stop at stack
bounds via kstack_end().
Enable CONFIG_STACKTRACE_SUPPORT and CONFIG_ARCH_STACKWALK
so generic stacktrace users (dump_stack(), /proc/*/stack,
SysRq backtraces, etc.) work on Alpha.
This provides functional in-kernel stack traces without
requiring frame pointer unwinding.
Reviewed-by: Matt Turner <mattst88@gmail.com>
Tested-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Magnus Lindholm <linmag7@gmail.com>
Link: https://lore.kernel.org/r/20260706170019.2941459-3-linmag7@gmail.com
Signed-off-by: Magnus Lindholm <linmag7@gmail.com>
Add a user_regset_view for Alpha and switch ELF core dumping to
CORE_DUMP_USE_REGSET. General-purpose registers are exported in
ELF gregs layout, including callee-saved registers and a correct
user stack pointer.
The user stack pointer is not preserved in pt_regs on Alpha, so expose
it from the PCB, or via rdusp() for the current task, when building the
ELF register image. This makes the user stack pointer consistent for
core dumps, ptrace regsets, and PTRACE_GET_SYSCALL_INFO.
Implement regset get/set callbacks for both NT_PRSTATUS and NT_PRFPREG.
The callbacks translate between Alpha's pt_regs/thread state and the
ELF-visible register layouts, while the common ptrace regset code handles
PTRACE_GETREGSET and PTRACE_SETREGSET iovec semantics. This avoids
duplicating subtle short-buffer and oversized-buffer behavior in
arch_ptrace().
With these changes Alpha satisfies the requirements for
HAVE_ARCH_TRACEHOOK and selects it, enabling generic tracehook and
ptrace syscall-info code paths without changing the existing syscall
entry ABI.
Reviewed-by: Matt Turner <mattst88@gmail.com>
Tested-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Magnus Lindholm <linmag7@gmail.com>
Link: https://lore.kernel.org/r/20260706170019.2941459-2-linmag7@gmail.com
Signed-off-by: Magnus Lindholm <linmag7@gmail.com>
Move irq_set_chip_and_handler() and irq_set_status_flags() calls
outside the io7->irq_lock raw spinlock. These functions take
sparse_irq_lock, which is a mutex, and taking a sleeping lock while
holding a raw spinlock is invalid. The raw spinlock only needs to
protect the hardware CSR accesses.
This fixes the following lockdep splat during boot:
[ BUG: Invalid wait context ]
swapper/0/0 is trying to lock:
sparse_irq_lock{....}-{4:4}, at: irq_mark_irq
other info that might help us debug this:
context-{5:5}
1 lock held by swapper/0/0:
#0: &io7->irq_lock{....}-{2:2}, at: init_io7_irqs.constprop.0
Cc: stable@vger.kernel.org
Assisted-by: Claude:claude-opus-4-6
Signed-off-by: Matt Turner <mattst88@gmail.com>
Reviewed-by: Magnus Lindholm <linmag7@gmail.com>
Link: https://lore.kernel.org/r/20260528230516.1839694-2-mattst88@gmail.com
Signed-off-by: Magnus Lindholm <linmag7@gmail.com>
Pull NTB updates from Jon Mason:
"An EPF bug fix to prevent an invalid unmap during device removal,
along with documentation fixes and minor AMD driver cleanups"
* tag 'ntb-7.2' of https://github.com/jonmason/ntb:
ntb: amd: Use named initializer for pci_device_id::driver_data
NTB: fix kernel-doc warnings in ntb.h
NTB: epf: Avoid pci_iounmap() with offset when PEER_SPAD and CONFIG share BAR
ntb_hw_amd: Fix incorrect debug message in link disable path
Pull more input updates from Dmitry Torokhov:
- Updates to Synaptics RMI4 driver to fix potential OOB accesses in F30
and F3A keymap handling
- A workaround in Synaptics RMI4 to tolerate buggy firmware on some
touchpads (e.g. ThinkPad T14 Gen 1) that report incomplete register
descriptor structures, preventing probe failures
- A revert of an incorrect register descriptor address calculation in
Synaptics RMI4 driver
- A fix for a regression in HP GSC PS/2 (gscps2) driver where the
receive buffer write index was not advanced, leaving keyboard and
mouse unusable.
* tag 'input-for-v7.2-rc0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: gscps2 - advance receive buffer write index
Input: rmi4 - tolerate short register descriptor structure
Revert "Input: rmi4 - fix register descriptor address calculation"
Input: synaptics-rmi4 - bound the F30 keymap to the GPIO/LED count
Input: synaptics-rmi4 - bound the F3A keymap to the GPIO count
Pull pwm fixes from Uwe Kleine-König:
"Two more fixes that I managed to put into the public branch merged
into next before my first pull request but missed to include them in
it.
The first change is a relevant change that fixes misconfigurations due
to a variable overflow. The second is only cosmetic but very obviously
an improvement"
* tag 'pwm/for-7.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux:
pwm: rzg2l-gpt: Add missing newlines to dev_err_probe() messages
pwm: rzg2l-gpt: Fix period_ticks type from u32 to u64
Pull more fbdev updates from Helge Deller:
"Fixes for generic fbdev & fbcon code for the handling of modelists
and preventing a potential NULL ptr dereference in the console code.
Fix missed cleanups in the error path of various fbdev drivers.
And Uwe Kleine-König contributed a cleanup patch to use named
initializers in the vga16fb driver"
* tag 'fbdev-for-7.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev:
fbdev: Fix fb_new_modelist to prevent null-ptr-deref in fb_videomode_to_var
fbcon: fix NULL pointer dereference for a console without vc_data
fbdev: fix use-after-free in store_modes()
fbdev: viafb: return an error when DMA copy times out
fbdev: goldfishfb: fail pan display on base-update timeout
fbdev: fbcon: fix out-of-bounds read in err_out of fbcon_do_set_font()
fbdev: pm2fb: unwind WC setup on probe failure
fbdev: vga16fb: Drop unused assignment of platform_device_id driver data
Pull sound fixes from Takashi Iwai:
"A collection of small bug fixes accumulated over the last week.
Most are device-specific fixes while there are a few core fixes as
well.
Here are the highlights:
ALSA Core:
- A fix for an uninitialised heap leak in ALSA sequencer core
- A fix for error handling/resource leak in compress-offload API
USB-audio:
- A teardown-ordering fix in USB MIDI 2.0 to prevent use-after-free
- Bounds and length checks for packet data in Native Instruments
caiaq / Traktor Kontrol input parsers
- Avoidance of expensive kobject path lookups in DualSense controller
matches
- Robustness/memory leak fixes for Qualcomm USB offload driver
- Focusrite Control Protocol (FCP) NULL-pointer dereference fix and a
new device quirk (ISA C8X)
- Device-specific quirks for Yamaha CDS3000 and SC13A
HD-Audio:
- A bunch of quirks and mute/mic-mute LED fixups for various laptops
(Acer, Clevo, Lenovo, HP)
ASoC & SoundWire:
- Avoid failing card registration if the device_link creation fails
- A workaround for SoundWire randconfig build failures by making
helper functions static inline
- Corrected MCLK reference validation for CS530x codecs
- Clean up of untested, problematic guard() macro replacements in
Rockchip SAI driver
- Fix for eDMA maxburst misalignment with channel count in Freescale
ASRC
- Miscellaneous hardware-specific fixes (qcom, rt5650, tlv320aic3x,
tas2781/3)
Others:
- Bounds and length checks for packet data in Apple iSight"
* tag 'sound-fix-7.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (46 commits)
ALSA: FCP: Fix NULL pointer dereference in interface lookup
ALSA: hda/realtek: Update Acer Nitro ANV15-41 quirk to enable mute LED
ASoC: fsl_asrc_dma: fix eDMA maxburst misalignment with channel count
ASoC: codecs: pcm512x: only print info once on no sclk
ASoC: tas2781: Update default register address to TAS2563
ALSA: firewire: isight: bound the sample count to the packet payload
ALSA: usb-audio: qcom: Free QMI handle
ALSA: hda: Add Lenovo Legion 7i 16IAX7 17AA3874 quirk
ALSA: usb-audio: avoid kobject path lookup in DualSense match
ALSA: hda/realtek: Add quirk for Acer Nitro ANV15-41
ASoC: soc-core: Don't fail if device_link could not be created
ASoC: rockchip: rockchip_sai: #include <linux/platform_device.h> explicitly
ALSA: seq: Fix uninitialised heap leak in snd_seq_event_dup()
ASoC: rt5575: Use __le32 for SPI burst write address
ASoC: tas2783: Update loaded firmware names to linux-firmware 20260519
ASoC: SDCA: Validate written enum value in ge_put_enum_double()
ASoC: realtek: Add back local call to sdw_show_ping_status()
ASoC: ti: Add back local call to sdw_show_ping_status()
ASoC: max98373: Add back local call to sdw_show_ping_status()
ASoC: es9356: Add back local call to sdw_show_ping_status()
...
Pull RTC updates from Alexandre Belloni:
"Most of the work and improvements are for features of the m41t93.
The ds1307 also gets support for OSF (Oscillator Stop Flag) for
new variants.
The pcap driver is being removed as the Motorola EZX support was
removed a while ago.
Subsystem:
- add rtc_read_next_alarm() to read next expiring timer
Drivers:
- ds1307: handle OSF for ds1337/ds1339/ds3231, add clock provider for
ds1307, fix wday for rx8130
- m41t93: DT support, alarm, clock provider, watchdog support
- mv: add suspend/resume support for wakeup
- pcap: remove driver
- renesas-rtca3: many fixes"
* tag 'rtc-7.2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (36 commits)
rtc: ds1307: update reference to removed CONFIG_RTC_DRV_DS1307_HWMON
platform/x86: amd-pmc: Fix S0i3 wakeup with alarmtimer
rtc: s35390a: fix typo in comment
rtc: cmos: unregister HPET IRQ handler on probe failure
rtc: ds1307: Fix off-by-one issue with wday for rx8130
dt-bindings: rtc: ds1307: Add epson,rx8901
rtc: bq32000: add delay between RTC reads
rtc: m41t93: Add watchdog support
rtc: m41t93: Add square wave clock provider support
rtc: m41t93: Add alarm support
rtc: m41t93: migrate to regmap api for register access
rtc: m41t93: add device tree support
dt-bindings: rtc: Add ST m41t93
rtc: ds1307: add support for clock provider in ds1307
rtc: mv: add suspend/resume support for wakeup
rtc: aspeed: add AST2700 compatible
dt-bindings: rtc: add ASPEED AST2700 compatible
rtc: interface: fix typos in rtc_handle_legacy_irq() documentation
rtc: msc313: fix NULL deref in shared IRQ handler at probe
rtc: remove unused pcap driver
...
Pull fscrypt fixes from Eric Biggers:
- Fix a bug where in a specific edge case, file contents en/decryption
could be done with the wrong data unit size
- Fix the data structure used for keeping track of users that have
added an fscrypt key to be a simple list instead of a 'struct key'
keyring
This fixes issues such as a lockdep report found by syzbot and
possible unintended interactions with the keyctl() system calls
* tag 'fscrypt-for-linus' of git://git.kernel.org/pub/scm/fs/fscrypt/linux:
fscrypt: Replace mk_users keyring with simple list
fscrypt: Fix key setup in edge case with multiple data unit sizes
Commit 44f9200699 ("Input: gscps2 - use guard notation when
acquiring spinlock") moved the receive loop into gscps2_read_data()
and gscps2_report_data().
While moving the code, it preserved the writes to
buffer[ps2port->append], but omitted the following producer index
update from the original loop:
ps2port->append = (ps2port->append + 1) & BUFFER_SIZE;
As a result, append never advances. Since gscps2_report_data() only
reports bytes while act != append, the receive buffer always appears
empty and no keyboard or mouse data reaches the serio core.
Restore the omitted index update.
Fixes: 44f9200699 ("Input: gscps2 - use guard notation when acquiring spinlock")
Cc: stable@vger.kernel.org # 6.13+
Signed-off-by: Xu Rao <raoxu@uniontech.com>
Link: https://patch.msgid.link/460B5655BA580C60+20260624094739.850306-1-raoxu@uniontech.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some touchpads (e.g. ThinkPad T14 Gen 1) have buggy firmware that reports
a register descriptor structure size that is too small for the number of
registers it claims to have in the presence map. The remaining bytes in
the structure are 0, which with the new strict bounds checking causes the
parser to fail with -EIO, aborting the device probe.
Tolerate such short reads by dropping the remaining (unparseable or
0-size) registers from the list instead of failing the probe,
preventing the driver from trying to use them.
Fixes: 0adb483fbf ("Input: rmi4 - refactor register descriptor parsing")
Reported-by: Barry K. Nathan <barryn@pobox.com>
Tested-by: Barry K. Nathan <barryn@pobox.com>
Cc: stable@vger.kernel.org
Assisted-by: Antigravity:gemini-3.5-flash
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The register descriptor presence register is a packet register, which
means its bytes share a single RMI address. It does not occupy
consecutive addresses, and the register structure that follows it
is located at the next RMI address (presence_address + 1), not
(presence_address + presence_size).
Revert the incorrect address calculation introduced in commit
a98518e724.
Reported-by: "Barry K. Nathan" <barryn@pobox.com>
Tested-by: "Barry K. Nathan" <barryn@pobox.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The current list initialisation depends on the well hidden two zeros in
the PCI_VDEVICE macro. Instead use a named initialisation that is more
robust and easier to understand.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Correct a function name and function parameter name to avoid
kernel-doc warnings:
Warning: include/linux/ntb.h:575 expecting prototype for
ntb_default_port_count(). Prototype was for ntb_default_peer_port_count()
instead
Warning: include/linux/ntb.h:590 function parameter 'pidx' not
described in 'ntb_default_peer_port_number'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
When BAR_PEER_SPAD and BAR_CONFIG share one PCI BAR, the module teardown
path ends up calling pci_iounmap() on the same iomem with some offset,
which is unnecessary and triggers a kernel warning like the following:
Trying to vunmap() nonexistent vm area (0000000069a5ffe8)
WARNING: mm/vmalloc.c:3470 at vunmap+0x58/0x68, CPU#5: modprobe/2937
[...]
Call trace:
vunmap+0x58/0x68 (P)
iounmap+0x34/0x48
pci_iounmap+0x2c/0x40
ntb_epf_pci_remove+0x44/0x80 [ntb_hw_epf]
pci_device_remove+0x48/0xf8
device_remove+0x50/0x88
device_release_driver_internal+0x1c8/0x228
driver_detach+0x50/0xb0
bus_remove_driver+0x74/0x100
driver_unregister+0x34/0x68
pci_unregister_driver+0x34/0xa0
ntb_epf_pci_driver_exit+0x14/0xfe0 [ntb_hw_epf]
[...]
Fix it by unmapping only when PEER_SPAD and CONFIG use difference bars.
Cc: stable@vger.kernel.org
Fixes: e75d5ae8ab ("NTB: epf: Allow more flexibility in the memory BAR map method")
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Koichiro Den <den@valinux.co.jp>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
amd_ntb_link_disable() prints "Enabling Link" which is misleading.
Update the message to reflect that the link is being disabled.
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Pull drm fixes from Dave Airlie:
"These are just the fixes from our fixes branch, all pretty small and
scattered.
sysfb:
- drm/sysfb truncation and alignment fixes
edid:
- fix edid OOB read in tile parsing
- increase displayid topology id to correct size
nouveau:
- fix error handling paths in nouveau
amdxdna:
- get_bo_info fix
ivpu:
- fix leak when error handling in ivpu"
* tag 'drm-fixes-2026-06-27' of https://gitlab.freedesktop.org/drm/kernel:
drm/sysfb: Avoid truncating maximum stride
drm/sysfb: Return errno code from drm_sysfb_get_visible_size()
drm/sysfb: Avoid possible truncation with calculating visible size
drm/sysfb: Do not page-align visible size of the framebuffer
drm/edid: fix OOB read in drm_parse_tiled_block()
drm/nouveau: fix reversed error cleanup order in ucopy functions
drm/nouveau/acr: fix missing nvkm_done() in error path of nvkm_acr_oneinit()
accel/amdxdna: Use caller client for debug BO sync
drm/displayid: fix Tiled Display Topology ID size
accel/ivpu: fix HWS command queue leak on registration failure
Pull drm merge window fixes from Dave Airlie:
"This is the merge window fixes from our next tree, i915/xe and amdgpu
make up all of it.
I've got a separate fixes pull from our fixes branch arriving after
this.
i915:
- Fix corrupted display output on GLK, #16209
- Add missing Spectre mitigation for parallel submit IOCTL
- MTL+ fix for DP resume
- clear CRTC blobs after dropping refs
- fix sharpness filter on DP MST
xe:
- Set TTM beneficial order to 9 in Xe
- Several error path cleanups
- Fix TDR for unstarted jobs on kernel queues
- Several TLB invalidation fixes related to suspending LR queues
- Some small RAS fixes
- Multi-queue suspend fix for LR queues
- Revert inclusion of NVL_S firmware
amdgpu:
- devcoredump fixes
- SMU15 fix
- Various irq put/get imbalance cleanup fixes
- 8K panel fix
- DCN3.5 fix
- lockdep fix
- Cleaner shader sysfs IB overflow fix
- Async flip fixes
- GET_MAPPING_INFO fix
- CP_GFX_SHADOW fix
- Ctx pstate handling fix
- GTT bo move handling fixes
- Old UVD BO placement fixes
- GC9 mode2 reset fix
- IH6.1 version fix
- Soft IH ring fix
amdkfd:
- Fix doorbell/mmio double unpin on free
- CRIU fixes
- SMI event fixes
- Sysfs teardown fix
- Various boundary checking fixes
- Various error checking fixes
- SVM fix"
* tag 'drm-next-2026-06-27' of https://gitlab.freedesktop.org/drm/kernel: (52 commits)
drm/i915/cdclk: Fix up CDCLK_FREQ_DECIMAL without a full PLL re-enable
drm/i915/gem: Add missing nospec on parallel submit slot
drm/amdgpu: Use system unbound workqueue for soft IH ring
amdgpu/ih6.1: Fix minor version
drm/amdkfd: Use exclusive bounds for SVM split alignment checks
drm/amdgpu/gfx9: Fix Ring and IB test fail after mode2
drm/amdgpu/uvd: Fix forcing MSG, FB BOs into VCPU segment when it isn't at 0 (v2)
drm/amdgpu/uvd: Place VCPU BO only in VRAM for UVD 4.x and older
drm/amdgpu: Fix amdgpu_bo_move() when old_mem and new_mem are both GTT
drm/amdgpu: Respect placement requirements in amdgpu_gtt_mgr functions
drm/amdgpu: Fix context pstate override handling
drm/amdkfd: Use memdup_array_user to copy data from/to user space at kfd ioctls
drm/amdkfd: check find_first_zero_bit before __set_bit on kfd->doorbell_bitmap
drm/amdkfd: Let driver decide buffer size at AMDKFD_IOC_GET_DMABUF_INFO ioctl
drm/amdgpu: fix recursive ww_mutex acquire in amdgpu_devcoredump_format
drm/amdgpu: convert amdgpu_vm_lock_by_pasid() to drm_exec
drm/amdgpu: Don't use UTS_RELEASE directly
drm/amdkfd: Fix NULL deref during sysfs teardown
drm/amdgpu: validate CP_GFX_SHADOW chunk size in CS pass1
drm/amdgpu: check amdgpu_vm_bo_find() result in GET_MAPPING_INFO
...
Pull ceph updates from Ilya Dryomov:
"This adds support for manual client session reset in CephFS, allowing
operators to get out of tricky livelock situations involving caps and
file locks without evicting the problematic client instance on the MDS
side or rebooting the client node both of which can be disruptive"
* tag 'ceph-for-7.2-rc1' of https://github.com/ceph/ceph-client:
ceph: add manual reset debugfs control and tracepoints
ceph: add client reset state machine and session teardown
ceph: add diagnostic timeout loop to wait_caps_flush()
ceph: harden send_mds_reconnect and handle active-MDS peer reset
ceph: use proper endian conversion for flock_len in reconnect
ceph: convert inode flags to named bit positions and atomic bitops
rbd: switch to dynamic root device
Pull thermal control fixes from Rafael Wysocki:
"These fix a failure path in an Intel thermal driver and prevent
thermal testing module code from being executed after it has been
freed:
- Fix dangling resources on thermal_throttle_online() failure in the
Intel thermal_throttle driver (Ricardo Neri)
- Eliminate a possibility of running thermal testing module code
after that module has been removed (Rafael Wysocki)"
* tag 'thermal-7.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal: testing: zone: Flush work items during cleanup
thermal: intel: Fix dangling resources on thermal_throttle_online() failure
Pull power management fixes from Rafael Wysocki:
"These fix the schedutil cpufreq governor and drop a bogus warning
from the cpuidle core:
- Remove a misguided warning along with an inaccurate comment
next to it from the cpuidle core (Rafael Wysocki)
- Clear need_freq_update as appropriate in the .adjust_perf()
path of the schedutil cpufreq governor to avoid calling
cpufreq_driver_adjust_perf() unnecessarily on every scheduler
utilization update (Zhongqiu Han)"
* tag 'pm-7.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: Allow exit latency to exceed target residency
cpufreq: schedutil: Fix uncleared need_freq_update on the .adjust_perf() path
Pull ACPI support fixes and cleanups from Rafael Wysocki:
"These fix assorted issues and do cleanups in the ACPI support code,
which includes a fix for tools build breakage related to strncpy()
removal:
- Unbreak ACPICA tools builds after switching over to using
strscpy_pad() that is kernel-specific (Rafael Wysocki)
- Fix module parameter file paths in comments in the ACPI code
managing the general sysfs attributes (Zenghui Yu)
- Update kerneldoc comments in the ACPI resource management code to
follow the common style (Andy Shevchenko)
- Fix inverted interface check in ipmi_bmc_gone() that may cause ACPI
IPMI interfaces to be mishandled (Xu Rao)
- Add __cpuidle annotation to idle state management functions related
to ACPI _LPI to avoid trace-induced RCU warnings (Li RongQing)"
* tag 'acpi-7.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: processor_idle: Mark LPI enter functions as __cpuidle
ACPICA: Unbreak tools build after switching over to strscpy_pad()
ACPI: IPMI: Fix inverted interface check in ipmi_bmc_gone()
ACPI: resource: Amend kernel-doc style
ACPI: sysfs: Fix path of module parameters in comments
Pull spi fixes from Mark Brown:
"A fairly unremarkable collection of fixes that came in over the
merge window, plus a new device ID for the DesignWare controller
in the StarFive JHB100 SoC.
There's a couple of core fixes included, one avoiding freeing an
empty resource in error handling cases and another which fixes a
NULL dereference which could be triggered by using an abnormal
device registration flow like driver_override"
* tag 'spi-fix-v7.2-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: imx: reconfigure for PIO when DMA cannot be started
spi: dw: Add support for snps,dwc-ssi-2.00a
spi: dt-bindings: snps,dw-apb-ssi: Add starfive,jhb100-spi
spi: rpc-if: Use correct device for hardware reinitialization on resume
spi: acpi: Free resource list at appropriate time
spi: dw: fix wrong BAUDR setting after resume
spi: uniphier: Fix completion initialization order before devm_request_irq()
spi: Add NULL check for spi_get_device_id() in spi_get_device_match_data()
Pull regulator fixes from Mark Brown:
"A couple of unremarkable driver specific fixes that came in during the
merge window"
* tag 'regulator-fix-v7.2-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: da9121: Use subvariant ids in the I2C table
regulator: pca9450: Correct default t_off_deb for PCA9451A/PCA9452
Pull regmap fix from Mark Brown:
"Ensure that we don't overwrite the error code when cleaning up a
failed cache initialisation, helping people debug issues if they
do arise"
* tag 'regmap-fix-v7.2-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regcache: Do not overwrite error code when finalizing cache after error
Merge a fix eliminating a possibility of running the thermal testing
module code after that module has been removed.
* thermal-testing:
thermal: testing: zone: Flush work items during cleanup
Merge a cpuidle core fix that removes a misguided warning along with an
inaccurate comment next to it.
* pm-cpuidle:
cpuidle: Allow exit latency to exceed target residency
Merge an update of comments regarding the ACPI sysfs code, a kernel-doc
style fixup update of ACPI resource management, and ACPI IPMI driver
fix, and an ACPI processor driver fix for 7.2-rc1:
- Fix module parameter file paths in comments in the ACPI code managing
the general sysfs attributes (Zenghui Yu)
- Update kerneldoc comments in the ACPI resource management code to
follow the common style (Andy Shevchenko)
- Fix inverted interface check in ipmi_bmc_gone() which may cause ACPI
IPMI interfaces to be mishandled (Xu Rao)
- Add __cpuidle to idle state management functions related to ACPI _LPI
to avoid trace-induced RCU warnings (Li RongQing)
* acpi-sysfs:
ACPI: sysfs: Fix path of module parameters in comments
* acpi-resource:
ACPI: resource: Amend kernel-doc style
* acpi-driver:
ACPI: IPMI: Fix inverted interface check in ipmi_bmc_gone()
* acpi-processor:
ACPI: processor_idle: Mark LPI enter functions as __cpuidle
Pull devicetree fixes from Rob Herring:
- Drop unnecessary type reference from khadas,mcu "fan-supply"
- Fix clocks in Renesas R-Mobile APE6 example
- Add missing Unisoc SC2730 PMIC regulators schema
- Fix Amlogic thermal example
- kernel-doc fix for of_map_id()
- Handle negative index in of_fwnode_get_reference_args()
* tag 'devicetree-fixes-for-7.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: mfd: khadas,mcu: Drop type reference from "fan-supply"
dt-bindings: clock: renesas: div6: Use ZT/ZTR trace clock in R-Mobile APE6 example
regulator: dt-bindings: Add Unisoc SC2730 PMIC
dt-bindings: thermal: amlogic: Correct 'reg' in the example
dt-bindings: thermal: amlogic: Fix missing header in the example
of: Fix RST inline emphasis warnings in of_map_id() kernel-doc
of: property: Fix of_fwnode_get_reference_args() with negative index
Pull LoongArch updates from Huacai Chen:
- Add THREAD_INFO_IN_TASK implementation
- Add build salt to the vDSO
- Add some BPF JIT inline helpers
- Update DTS for I2C clocks and clock-frequency
- Some bug fixes and other small changes
* tag 'loongarch-7.2' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
selftests/bpf: Test jited inline of bpf_get_smp_processor_id() for LoongArch
selftests/bpf: Test jited inline of bpf_get_current_task() for LoongArch
selftests/bpf: Add __arch_loongarch to limit test cases for LoongArch
selftests/bpf: Add get_preempt_count() support for LoongArch
LoongArch: dts: Add i2c clocks and clock-frequency properties to LS2K2000
LoongArch: dts: Add i2c clocks and clock-frequency properties to LS2K1000
LoongArch: dts: Add i2c clocks and clock-frequency properties to LS2K0500
LoongArch: BPF: Inline bpf_get_smp_processor_id() helper
LoongArch: BPF: Inline bpf_get_current_task/_btf() helpers
LoongArch: BPF: Fix off-by-one error in tail call
LoongArch: BPF: Fix outdated tail call comments
LoongArch: Add build salt to the vDSO
LoongArch: Fix nr passing in set_direct_map_valid_noflush()
LoongArch: Fix missing dirty page tracking in {pte,pmd}_wrprotect()
LoongArch: Move struct kimage forward declaration before use
LoongArch: Report dying CPU to RCU in stop_this_cpu()
LoongArch: Add PIO for early access before ACPI PCI root register
LoongArch: Add THREAD_INFO_IN_TASK implementation
Pull arm64 fixes from Will Deacon:
"Small crop of arm64 fixes for -rc1. We've got a build fix for a new
randconfig permutation, a fix for a long-standing truncation issue
with hardware watchpoints and a KVM initialisation fix for the newly
merged remapping of the kernel data and bss sections:
- Fix randconfig build failure due to missing include of asm/insn.h
- Reject unaligned hardware watchpoints which were silently being
truncated
- Fix crash in KVM initialisation by deferring the read-only
remapping of the kernel data and bss sections"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mm: Defer read-only remap of data/bss linear alias
arm64/hw_breakpoint: reject unaligned watchpoints that would truncate BAS
arm64: static_call: include asm/insns.h
Pull ecryptfs updates from Tyler Hicks:
"No functional changes, just code cleanups:
- replace kmalloc()/snprintf() with kasprintf()
- simplify code flow by removing an unnecessary variable"
* tag 'ecryptfs-7.2-rc1-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
ecryptfs: use kasprintf in ecryptfs_crypto_api_algify_cipher_name
ecryptfs: remove redundant variable found_auth_tok
Pull smb server updates from Steve French:
"This is mostly a correctness and compatibility update for ksmbd's
SMB2/3 lease, oplock, durable handle, compound request, CREATE,
rename, stream and share-mode handling.
A large part of the series fixes cases found by smbtorture where ksmbd
diverged from the SMB2/3 protocol requirements.
The main changes are:
- Rework SMB2 lease state handling so lease state is shared per
ClientGuid/LeaseKey across opens, with better validation of lease
create contexts, ACK handling, epochs, break-in-progress reporting,
v2 lease notification routing, and chained lease breaks
- Fix several oplock break corner cases, including ACK validation,
timeout downgrade behavior, level-II break handling on unlink,
share-conflict lease breaks, and read-control/stat-open behavior
- Fix durable handle behavior around delete-on-close, stale
reconnects, reconnect context parsing, oplock/lease break
invalidation, and durable v2 AppInstanceId replacement
- Fix compound request handling so related commands propagate failed
statuses correctly, preserve response framing across chained
errors, keep compound FIDs across READ/WRITE/FLUSH, and send
interim STATUS_PENDING where clients expect cancellable compound
I/O
- Tighten CREATE and stream semantics, including create attribute
validation, allocation size reporting, explicit create security
descriptors, unnamed DATA stream handling, stream directory
validation, and stream delete sharing against the base file
- Fix rename and metadata behavior, including parent directory
sharing checks, denying directory rename with open children, and
preserving SMB ChangeTime across rename for open handles
- Fix two important safety issues: a multichannel byte-range lock
list owner race that could lead to use-after-free, and an NTLMv2
session key update before authentication proof validation
- Fix a concurrent SMB2 NEGOTIATE preauth use-after-free, a UBSAN
warning in compression capability parsing, a false hung-task
warning in the durable handle scavenger, endian debug logging,
Smatch indentation warnings, and kernel-doc warnings
- Increase the default SMB3 transaction size from 1MB to 4MB to
better match modern read/write negotiation and improve sequential
I/O behavior"
* tag 'v7.2-rc-part2-smb3-server-fixes' of git://git.samba.org/ksmbd: (50 commits)
ksmbd: fix kernel-doc warnings in smb2_lease_break_noti()
ksmbd: fix inconsistent indenting warnings
ksmbd: validate NTLMv2 response before updating session key
ksmbd: increase SMB3_DEFAULT_TRANS_SIZE from 1MB to 4MB
ksmbd: fix UBSAN array-index-out-of-bounds in decode_compress_ctxt()
ksmbd: sleep interruptibly in the durable handle scavenger
ksmbd: start file id allocation at 1
ksmbd: treat read-control opens as stat opens only for leases
ksmbd: validate :: stream type against directory create
ksmbd: break conflicting-open leases only as far as needed
ksmbd: break handle caching for share conflicts
ksmbd: normalize ungrantable lease states
ksmbd: return oplock protocol error for level II ack
ksmbd: avoid level II oplock break notification on unlink
ksmbd: downgrade oplock after break timeout
ksmbd: apply create security descriptor first
ksmbd: return requested create allocation size
ksmbd: tighten create file attribute validation
ksmbd: reject empty-attribute synchronize-only create
ksmbd: honor stream delete sharing for base file
...
info->var, a framebuffer's current mode, is expected to have a matching
entry in info->modelist. var_to_display() relies on this and treats a
failed fb_match_mode() as "This should not happen". fb_set_var() keeps it
true by adding the mode to the list on every change, and
do_register_framebuffer() does the same at registration.
store_modes() replaces the modelist from userspace. fb_new_modelist()
validates the new modes but does not check that info->var still has a
match. It relies on fbcon_new_modelist() to re-point consoles, but that
only handles consoles mapped to the framebuffer. With fbcon unbound there
are none, so info->var is left describing a mode that is no longer in the
list.
A later console takeover runs var_to_display(), where fb_match_mode()
returns NULL and leaves fb_display[i].mode NULL. fbcon_switch() passes it
to display_to_var(), and fb_videomode_to_var() dereferences the NULL mode.
Keep the current mode in the list in fb_new_modelist(), the same way
fb_set_var() does.
Cc: stable@vger.kernel.org
Assisted-by: Claude:claude-opus-4-8
Signed-off-by: Ian Bridges <icb@fastmail.org>
Signed-off-by: Helge Deller <deller@gmx.de>
fbcon_new_modelist() runs when a framebuffer's modelist changes. For each
console mapped to it with fb_display[i].mode set, it reads vc_cons[i].d and
passes the vc_num to fbcon_set_disp(). This assumes a console with a mode
set has a vc_data, but it can be NULL. fbcon_set_disp() sets
fb_display[i].mode before it checks vc_data, and fbcon_deinit() leaves the
mode set after the vc_data is freed. fbcon_new_modelist() then dereferences
the NULL vc_data.
Keep fb_display[i].mode set only while the console has a vc_data. Check
vc_data before setting the mode in fbcon_set_disp(), and clear the mode in
fbcon_deinit(). The existing mode check in fbcon_new_modelist() then skips
such consoles.
Reported-by: syzbot+42525d636f430fd5d983@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=42525d636f430fd5d983
Cc: stable@vger.kernel.org
Assisted-by: Claude:claude-opus-4-8
Signed-off-by: Ian Bridges <icb@fastmail.org>
Signed-off-by: Helge Deller <deller@gmx.de>
store_modes() replaces a framebuffer's modelist with modes from userspace.
On success it frees the old modelist with fb_destroy_modelist(). Two
fields still point into that freed list.
One pointer is fb_display[i].mode, the mode a console is using.
fbcon_new_modelist() moves these pointers to the new list. It only does so
for consoles still mapped to the framebuffer. An unmapped console is
skipped and keeps its stale pointer. Unbinding fbcon, for example, sets
con2fb_map[i] to -1 but leaves fb_display[i].mode set. An
FBIOPUT_VSCREENINFO ioctl with FB_ACTIVATE_INV_MODE later reaches
fbcon_mode_deleted(). That function reads the stale fb_display[i].mode
through fb_mode_is_equal(). The read is a use-after-free.
The other pointer is fb_info->mode, the current mode. It is set through
the mode sysfs attribute. store_modes() does not update fb_info->mode, so
it is left pointing into the freed list. show_mode(), the attribute's read
handler, dereferences the stale fb_info->mode through mode_string(). The
read is a use-after-free.
Clear both pointers before freeing the list. Commit a1f3058930 ("fbcon:
Set fb_display[i]->mode to NULL when the mode is released") added the
helper fbcon_delete_modelist(). It clears every fb_display[i].mode that
points into a given list. So far it is called only from the unregister
path. Call it from store_modes() too, and set fb_info->mode to NULL.
Reported-by: syzbot+81c7c6b52649fd07299d@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=81c7c6b52649fd07299d
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/ajjoDhAi2y4ArSlz@dev/
Assisted-by: Claude:claude-opus-4-8
Signed-off-by: Ian Bridges <icb@fastmail.org>
Signed-off-by: Helge Deller <deller@gmx.de>
A malformed USB device can provide a vendor-specific interface without
any endpoint descriptors. fcp_find_fc_interface() currently selects the
first vendor-specific interface and reads endpoint 0 from it, without
checking whether the interface actually has any endpoints.
When bNumEndpoints is zero, no endpoint array is allocated for the parsed
alternate setting, so get_endpoint(..., 0) yields an invalid endpoint
descriptor pointer. Dereferencing it through usb_endpoint_num() then
triggers a NULL pointer dereference.
Skip vendor-specific interfaces that do not have any endpoints.
Fixes: 46757a3e7d ("ALSA: FCP: Add Focusrite Control Protocol driver")
Reported-by: Jiaming Zhang <r772577952@gmail.com>
Closes: https://lore.kernel.org/lkml/CANypQFb1EHj0xX8bA1WxSOSK-5xca6ZNKzOQcp12=s=puY7VFw@mail.gmail.com/
Signed-off-by: Jiaming Zhang <r772577952@gmail.com>
Link: https://patch.msgid.link/20260625134933.425785-1-r772577952@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The laptop has a microphone mute LED on the F4 key, but it was not
taken in mind when the previous quirk was added
in commit 00e44a68ef ("ALSA:
hda/realtek: Add quirk for Acer Nitro ANV15-41").
Replace ALC2XX_FIXUP_HEADSET_MIC with ALC245_FIXUP_ACER_MICMUTE_LED,
which enables the LED and chains the previous quirk for the headset
microphone.
Fixes: 00e44a68ef ("ALSA: hda/realtek: Add quirk for Acer Nitro ANV15-41")
Signed-off-by: Oleg Kucheryavenko <oleg.kucheryavenko2018@gmail.com>
Link: https://patch.msgid.link/20260625134955.27465-1-oleg.kucheryavenko2018@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
