Adds LVDS decoder, HDMI encoder and connector for the Draak board.
The LVDS0 and LVDS1 encoders can use the DU_DOTCLKIN0, DU_DOTCLKIN1 and
EXTAL externals clocks. Two of them are provided to the SoC on the Draak
board, hook them up in DT.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the LVDS decoder, HDMI encoder, VGA encoder and HDMI and VGA
connectors, and wire up the display-related nodes with clocks, pinmux
and regulators.
The LVDS0 and LVDS1 encoders can use the DU_DOTCLKIN0, DU_DOTCLKIN1 and
EXTAL externals clocks. Two of them are provided to the SoC on the Ebisu
board, hook them up in DT.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
R-Car Gen3 SoCs need to enable/deassert clocks/resets of both usb 2.0
host (included phy) and peripheral. Otherwise, other side device
cannot work correctly. So, this patch revises properties of clocks
and resets. After that, each device driver can enable/deassert
clocks/resets by its self.
Notes:
- To work the renesas_usbhs driver correctly when host side drivers
are disabled and the renesas_usbhs driver doesn't have multiple
clock management, this patch doesn't change the order of the clocks
property in each hsusb node.
- This patch doesn't have any side-effects even if the renesas_usbhs
driver doesn't have reset_control and multiple clock management.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
It can't boot without bootargs settings on Uboot on ulcb board.
This patch adds missing default bootargs.
ulcb BSP can overwrite it by own UBoot settings.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
For R-Car V3H hook up SYS-DMAC1 and SYS-DMAC2 to IPMMU-DS1 to match
information in the R-Car Gen3 Rev.1.00 (April 2018) datasheet.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
For R-Car E3 hook up SYS-DMAC0, SYS-DMAC1 and SYS-DMAC2 to
IPMMU-DS0 and IPMMU-DS1 in same way as for R-Car H3.
This follows the R-Car Gen3 Rev.1.00 (April 2018) datasheet.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add HDMI and CVBS inputs device nodes to R-Car E3 Ebisu board.
Both HDMI and CVBS inputs are connected to an ADV7482 video decoder hooked to
the SoC CSI-2 receiver port.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The thermal device is supposed to be always enabled. As the default
value of the status property is "okay", there is no need to make this
explicit in SoC-specific .dtsi files where no override is involved.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
- Device nodes with unit addresses are sorted by unit address,
- Device nodes without unit addresses and references are sorted
alphabetically.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Successfully tested on H3 ES1.0 and ES2.0, M3-W ES1.0, and M3-N ES1.0.
Even previously stubborn cards work fine. Transfer rates were >60MB/s.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device nodes for all MSIOF SPI controllers, incl. clocks, power
domains, and resets properties.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device node for the external SCIF_CLK, and describe the clock
inputs for the Baud Rate Generator for External Clock (BRG) for SCIF2,
which can increase serial clock accuracy.
The presence of the SCIF_CLK crystal and its clock frequency depend on
the actual board.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Enhance patch description]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use the SoC-specific CPG/MSSR include file to allow future use of
R8A77990_CLK_* symbols.
Replace the hardcoded power domain indices by R8A77990_PD_* symbols.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The comments describing the non-default switch settings to use SATA are
confusing: 'Off' refers to the switch position, not to the MD12 logic
value, while the parentheses suggest otherwise. Rephrase to fix this.
Fixes: bec000784d5bb571 ("arm64: dts: renesas: salvator-xs: enable SATA")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This is based on the existing KF device tree sources:
$ ls -1 arch/arm64/boot/dts/renesas/*-kf.dts
arch/arm64/boot/dts/renesas/r8a7795-es1-h3ulcb-kf.dts
arch/arm64/boot/dts/renesas/r8a7795-h3ulcb-kf.dts
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb-kf.dts
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add FCPF and FCPV instances to the r8a774a1 dtsi, similarly
to what was done for the r8a7796 with commit 41dbbf0c5b
("arm64: dts: r8a7796: Add FCPF and FCPV instances"),
commit 69490bc966 ("arm64: dts: renesas: r8a7796: Point
FDP1 via FCPF to IPMMU-VI0"), and commit cef942d0bd ("arm64:
dts: renesas: r8a7796: Point VSPI via FCPVI to IPMMU-VC0").
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds definitions for L2 cache for the Cortex-A53 CPU
cores (512 KiB in size, organized as 32 KiB x 16 ways), adds
Cortex-A53 CPU cores (setting a total of 6 cores, 2 x Cortex-A57
+ 4 x Cortex-A53), and finally enables the performance monitor
unit for the Cortex-A53 cores on the R8A774A1 SoC.
Based on work done for r8a7796 SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device nodes for all RZ/G2M SCIF and HSCIF serial ports,
incl. clocks, power domains and DMAs.
According to the HW user manual, SCIF[015] and HSCIF[012] are
connected to both SYS-DMAC1 and SYS-DMAC2, while SCIF[34] and
HSCIF[34] are connected to SYS-DMAC0.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
