Pull "Broadcom devicetree changes for 4.10" from Florian Fainelli:
This pull request contains Broadcom ARM-based SoC Device Tree changes for 4.10,
please pull the following:
- Rafal adds support for the Netgear R8500 routers, adds basic support
for the Tenda AC9 router which uses the new BCM53573 SoC (single core Cortex
A7). He also enables the UART on the Netgear R8000 and restructures the
include files a bit for the BCM47094 SoC, finally he adds USB 3.0 PHY nodes
which enables USB 3.0 on BCM5301X devices that support it. Finally he adds
support for the TP-LINK Archer C9 V1 router.
- Kamal adds support for the QSPI controller on the Northstar Plus SoCs and updates
the bcm958625k reference board to have it enabled
- Dan adds support for the Luxul XAP-1510 (using a BCM4708) and XWR-3100 (using
a BCM47094)
- Scott fixes the pinctrl names in the Cygnus DTS files
- Jonathan enables the Broadcom iProc mailbox controller for Broadcom Cygnus/iProc
SoCs, he adds interrupt support for the GPIO CRMU hardware block and finally adds
the node for the OTP controller found on Cygnus SoCs
- Dhananjay enables the GPIO B controller on Norstarh Plus SoCs
- Eric defines standard pinctrl groups in the BCM2835 GPIO node
- Gerd adds definitions for the pinctrl groups and updates the PWM, I2C and SDHCI nodes
to use their appropriate pinctrl functions
- Linus adds names for the Raspberry Pi GPIO lines based on the datasheet
- Martin adds the DT binding and nodes for the Raspberry Pi firmware thermal block
- Stefan fixes a few typos with respect to the BCM2835 mailbox binding example and
Device Tree nodes he also fixes the Raspberry Pi GPIO lines names and finally
adds names for the Raspberry Zero GPIO lines
* tag 'arm-soc/for-4.10/devicetree' of http://github.com/Broadcom/stblinux: (29 commits)
ARM: bcm2835: Add names for the RPi Zero GPIO lines
ARM: bcm2835: Fix names for the Raspberry Pi GPIO lines
ARM: dts: enable GPIO-b for Broadcom NSP
ARM: BCM5301X: Add DT for TP-LINK Archer C9 V1
ARM: dts: Add node for Broadcom OTP controller driver
ARM: dts: Enable interrupt support for cygnus crmu gpio driver
ARM: dts: Enable Broadcom iProc mailbox controller
ARM: bcm2835: Add names for the Raspberry Pi GPIO lines
ARM: bcm2835: dts: add thermal node to device-tree of bcm283x
dt: bindings: add thermal device driver for bcm2835
ARM: dts: bcm283x: fix typo in mailbox address
DT: binding: bcm2835-mbox: fix address typo in example
ARM: dts: cygnus: fix naming of pinctrl node
ARM: BCM53573: Specify PMU and its ILP clock in the DT
ARM: BCM5301X: Add DT for Luxul XWR-3100
ARM: BCM5301X: Add DT for Luxul XAP-1510
ARM: BCM5301X: Specify USB 3.0 PHY in DT
ARM: BCM5301X: Enable UART on Netgear R8000
ARM: BCM5301X: Add separated DTS include file for BCM47094
ARM: dts: NSP: Add QSPI nodes to NSPI and bcm958625k DTSes
...
Merge "SoCFPGA DTS update for v4.10, part 3" from Dinh Nguyen:
- Fine tune L2 cache configuration
* tag 'socfpga_dts_for_v4.10_part_3' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: dts: socfpga: fine-tune L2 cache configuration
Pull "DaVinci DT updates for v4.10 (part 3)" from Sekhar Nori:
Some fixes for device-tree patches already queued.
- Fix SD card detect polarity
- Prevent Ethernet from picking a random mac address
- Fix error messages on platforms which dont use
bus master and emif priority settings.
* tag 'davinci-for-v4.10/dt-3' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850: enable memctrl and mstpri nodes per board
ARM: dts: da850-lcdk: Add ethernet0 alias to DT
ARM: dts: da850-lcdk: fix mmc card detect polarity
Pull "DaVinci DT updates for v4.10 (part 2)" from Sekhar Nori:
Adds device tree nodes enabling DDR controller
and bus master priority settings needed for
stable LCDC operation on DA850.
Also adds support for MUSB device on DA850
providing USB OTG support.
* tag 'davinci-for-v4.10/dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850-lcdk: Enable the usb otg device node
ARM: dts: da850: Add the usb otg device node
ARM: dts: da850: add the mstpri and ddrctl nodes
Currently the memory controller and master priorities drivers are
enabled in da850.dtsi. For boards for which there are no settings
defined, this makes these drivers emit error messages.
Disable the nodes in da850.dtsi and only enable them for da850-lcdk -
the only board that currently needs them.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
In order to avoid Linux generating a random mac address on every boot,
add an ethernet0 alias that will allow u-boot to patch the dtb with
the MAC address programmed into the EEPROM.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Pull "This device-tree pxa update brings" from Robert Jarzmik:
- pxa25x support
- cpu operating points in preparation for cpufreq-dt
- small fixes
* tag 'pxa-dt-4.10' of https://github.com/rjarzmik/linux:
ARM: dts: pxa: add pxa27x cpu operating points
ARM: dts: pxa: add pxa25x cpu operating points
ARM: dts: pxa: fix gpio0 and gpio1 interrupts
ARM: dts: pxa: fix no. of gpio cells in the pxa gpio binding documentation
ARM: dts: pxa: add pxa25x .dtsi file
Add PCIe support to the ARTPEC-6 SoC. This uses the existing
pcie-artpec6 driver.
So, all that is needed is device tree entries in the DTS.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Jesper Nilsson <jespern@axis.com>
Pull "ARM: OXNAS SoC DT updates for 4.10" from Neil Armstrong:
- Add DTSI for Oxford Semiconductor OX820
- Add DTS for Cloud Engines PogoPlug v3 board
- Fix MAINTAINERS Oxnas entry for dts files
from http://lkml.kernel.org/r/20161102141850.25164-1-narmstrong@baylibre.com
* tag 'oxnas-arm-soc-dt-for-4.10' of https://github.com/OXNAS/linux:
MAINTAINERS: oxnas: Add new files definitions
ARM: dts: Add support for OX820 and Pogoplug V3
Add a device node for the Product Register, which provides SoC product
and revision information.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Product Register, which provides SoC product
and revision information.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Product Register, which provides SoC product
and revision information.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Product Register, which provides SoC product
and revision information.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Product Register, which provides SoC product
and revision information.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Product Register, which provides SoC product
and revision information.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Product Register, which provides SoC product
and revision information.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Make it possible to fallback to GPIO for I2C4 on the EXIO-B connector.
This is based on reference work for the I2C0 core of the lager/r8a7790
by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[wsa: rebased and fixed aliases]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Make it possible to fallback to GPIO for I2C1 on the EXIO-C connector.
This is based on reference work for the I2C0 core of the lager/r8a7790
by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[wsa: rebased and fixed aliases]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Make it possible to select which I2C1 IP core you want to run on the
EXIO-A connector.
This is based on reference work for the I2C0 core of the lager board
by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[wsa: rebased and fixed aliases]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
The rename from i2cexio to i2cexio0 is in preparation for adding
i2cexio1 which will use the demuxer for IIC1/I2C1.
The reindexing from i2c8 to i2c10 is to allow space for grouping of
additional GPIO buses to be added by follow-up patches to support demuxing
of other i2c buses.
Also note that fallback to GPIO is not provided by the hardware for IIC0/I2C0.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[wsa: rebased, fixed alias and removed typo in commit message]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Update the PFC pin groups and function names of DU interface for
r8a7794 ALT board.
The currently specified pin groups and function names prevented PFC and
DU interfaces from being correctly configured:
sh-pfc e6060000.pin-controller: function 'du' not supported
sh-pfc e6060000.pin-controller: invalid function du in map table
sh-pfc e6060000.pin-controller: function 'du' not supported
sh-pfc e6060000.pin-controller: invalid function du in map table
sh-pfc e6060000.pin-controller: function 'du' not supported
sh-pfc e6060000.pin-controller: invalid function du in map table
sh-pfc e6060000.pin-controller: function 'du' not supported
sh-pfc e6060000.pin-controller: invalid function du in map table
rcar-du: probe of feb00000.display failed with error -22
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Hummingbird A31 board has a VGA DAC which converts RGB output
from the LCD interface to VGA analog signals.
Add nodes for the VGA DAC, its power supply, and enable this part
of the display pipeline.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Just like on sun8i all sun5i tablets use the same interrupt and power
gpios for their touchscreens. I've checked all known a13 fex files and
only the UTOO P66 uses a different gpio for the interrupt.
Add a touchscreen node to sun5i-reference-design-tablet.dtsi, which
fills in the necessary gpios to avoid duplication in the tablet dts files,
just like we do in sun8i-reference-design-tablet.dtsi.
This will make future patches adding touchscreen nodes to a13 tablets
simpler.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
