Michal Kalderon says:
====================
qed*: Error recovery process
Parity errors might happen in the device's memories due to momentary bit
flips which are caused by radiation.
Errors that are not correctable initiate a process kill event, which blocks
the device access towards the host and the network, and a recovery process
is started in the management FW and in the driver.
This series adds the support of this process in the qed core module and in
the qede driver (patches 2 & 3).
Patch 1 in the series revises the load sequence, to avoid PCI errors that
might be observed during a recovery process.
Changes in v2:
- Addressed issue found in https://patchwork.ozlabs.org/patch/1030545/
The change was done be removing the enum and passing a boolean to
the related functions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the error recovery process in the qede driver.
The process includes a partial/customized driver unload and load, which
allows it to look like a short suspend period to the kernel while
preserving the net devices' state.
Signed-off-by: Tomer Tayar <tomer.tayar@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the detection and handling of a parity error ("process kill
event"), including the update of the protocol drivers, and the prevention
of any HW access that will lead to device access towards the host while
recovery is in progress.
It also provides the means for the protocol drivers to trigger a recovery
process on their decision.
Signed-off-by: Tomer Tayar <tomer.tayar@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initiating final cleanup after an ungraceful driver unload can lead to bad
PCI accesses towards the host.
This patch revises the load sequence so final cleanup is sent while the
internal master enable is cleared, to prevent the host accesses, and clears
the internal error indications just before enabling the internal master
enable.
Signed-off-by: Tomer Tayar <tomer.tayar@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
is_broadcast_packet() expands to compare_ether_addr() which doesn't
exist since commit 7367d0b573 ("drivers/net: Convert uses of
compare_ether_addr to ether_addr_equal"). It turns out it's actually not
used.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: Misc updates
This patchset contains miscellaneous patches we gathered in our queue.
Some of them are dependencies of larger patchsets that I will submit
later this cycle.
Patches #1-#3 perform small non-functional changes in mlxsw.
Patch #4 adds more extended ack messages in mlxsw.
Patch #5 adds devlink parameters documentation for mlxsw. To be extended
with more parameters this cycle.
Patches #6-#7 perform small changes in forwarding selftests
infrastructure.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As for the others, check help message output to find out if devlink
supports "resource" object.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add initial documentation file for devlink params of mlxsw driver. Only
"fw_load_policy" is now supported.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the struct to the place where they belong, alongside with the rest
of the MR code.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to pass ruleset/group and chunk pointers on action_replace call
path, nobody uses them.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Wang says:
====================
tcp: change pingpong to 3 in delayed ack logic
TCP receiver today tries not to delay the ACKs to speed up the initial
slow start (a.k.a QUICK ACK mechanism). However the previous design
does not work well with modern TCP applications that starts with an
application-level handshake. For example, a HTTPs server often
receives the SSL hello and responds right away which triggers the TCP
stack to stop the quick ack and start delaying the ACKs based only one
instance of ping-pong. This patchset changes the threshold from 1 to 3
ping-pong transactions, so that we only start to delay the acks after
the receiver responds data quickly three times.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to be more confident about an on-going interactive session, we
increment pingpong count by 1 for every interactive transaction and we
adjust TCP_PINGPONG_THRESH to 3.
This means, we only consider a session in pingpong mode after we see 3
interactive transactions, and start to activate delayed acks in quick
ack mode.
And in order to not over-count the credits, we only increase pingpong
count for the first packet sent in response for the previous received
packet.
This is mainly to prevent delaying the ack immediately after some
handshake protocol but no real interactive traffic pattern afterwards.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using pingpong as a single bit information, we refactor the
code to treat it as a counter. When interactive session is detected,
we set pingpong count to TCP_PINGPONG_THRESH. And when pingpong count
is >= TCP_PINGPONG_THRESH, we consider the session in pingpong mode.
This patch is a pure refactor and sets foundation for the next patch.
This patch itself does not change any pingpong logic.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix blank line coding style issues, make the code cleaner.
Remove a redundant blank line in ip_rcv_core().
Insert a blank line in ip_rcv() between different statement blocks.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Libphy provides a standard set of helpers to access the MMD PHY
registers. Use those instead of relying on custom driver-specific
functions.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull KVM fixes from Paolo Bonzini:
"Quite a few fixes for x86: nested virtualization save/restore, AMD
nested virtualization and virtual APIC, 32-bit fixes, an important fix
to restore operation on older processors, and a bunch of hyper-v
bugfixes. Several are marked stable.
There are also fixes for GCC warnings and for a GCC/objtool interaction"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Mark expected switch fall-throughs
KVM: x86: fix TRACE_INCLUDE_PATH and remove -I. header search paths
KVM: selftests: check returned evmcs version range
x86/kvm/hyper-v: nested_enable_evmcs() sets vmcs_version incorrectly
KVM: VMX: Move vmx_vcpu_run()'s VM-Enter asm blob to a helper function
kvm: selftests: Fix region overlap check in kvm_util
kvm: vmx: fix some -Wmissing-prototypes warnings
KVM: nSVM: clear events pending from svm_complete_interrupts() when exiting to L1
svm: Fix AVIC incomplete IPI emulation
svm: Add warning message for AVIC IPI invalid target
KVM: x86: WARN_ONCE if sending a PV IPI returns a fatal error
KVM: x86: Fix PV IPIs for 32-bit KVM host
x86/kvm/hyper-v: recommend using eVMCS only when it is enabled
x86/kvm/hyper-v: don't recommend doing reset via synthetic MSR
kvm: x86/vmx: Use kzalloc for cached_vmcs12
KVM: VMX: Use the correct field var when clearing VM_ENTRY_LOAD_IA32_PERF_GLOBAL_CTRL
KVM: x86: Fix single-step debugging
x86/kvm/hyper-v: don't announce GUEST IDLE MSR support
Pull dma-mapping fix from Christoph Hellwig:
"Fix a xen-swiotlb regression on arm64"
* tag 'dma-mapping-5.0-2' of git://git.infradead.org/users/hch/dma-mapping:
arm64/xen: fix xen-swiotlb cache flushing
Pull libnvdimm fixes from Dan Williams:
"A fix for namespace label support for non-Intel NVDIMMs that implement
the ACPI standard label method.
This has apparently never worked and could wait for v5.1. However it
has enough visibility with hardware vendors [1] and distro bug
trackers [2], and low enough risk that I decided it should go in for
-rc4. The other fixups target the new, for v5.0, nvdimm security
functionality. The larger init path fixup closes a memory leak and a
potential userspace lockup due to missed notifications.
[1] https://github.com/pmem/ndctl/issues/78
[2] https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1811785
These have all soaked in -next for a week with no reported issues.
Summary:
- Fix support for NVDIMMs that implement the ACPI standard label
methods.
- Fix error handling for security overwrite (memory leak / userspace
hang condition), and another one-line security cleanup"
* tag 'libnvdimm-fixes-5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
acpi/nfit: Fix command-supported detection
acpi/nfit: Block function zero DSMs
libnvdimm/security: Require nvdimm_security_setup_events() to succeed
nfit_test: fix security state pull for nvdimm security nfit_test
Pull input fixes from Dmitry Torokhov:
"A fixup for the input_event fix for y2038 Sparc64, and couple other
minor fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: input_event - fix the CONFIG_SPARC64 mixup
Input: olpc_apsp - assign priv->dev earlier
Input: uinput - fix undefined behavior in uinput_validate_absinfo()
Input: raspberrypi-ts - fix link error
Input: xpad - add support for SteelSeries Stratus Duo
Input: input_event - provide override for sparc64
Pull networking fixes from David Miller:
1) Count ttl-dropped frames properly in mac80211, from Bob Copeland.
2) Integer overflow in ktime handling of bcm can code, from Oliver
Hartkopp.
3) Fix RX desc handling wrt. hw checksumming in ravb, from Simon
Horman.
4) Various hash key fixes in hv_netvsc, from Haiyang Zhang.
5) Use after free in ax25, from Eric Dumazet.
6) Several fixes to the SSN support in SCTP, from Xin Long.
7) Do not process frames after a NAPI reschedule in ibmveth, from
Thomas Falcon.
8) Fix NLA_POLICY_NESTED arguments, from Johannes Berg.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (42 commits)
qed: Revert error handling changes.
cfg80211: extend range deviation for DMG
cfg80211: reg: remove warn_on for a normal case
mac80211: Add attribute aligned(2) to struct 'action'
mac80211: don't initiate TDLS connection if station is not associated to AP
nl80211: fix NLA_POLICY_NESTED() arguments
ibmveth: Do not process frames after calling napi_reschedule
net: dev_is_mac_header_xmit() true for ARPHRD_RAWIP
net: usb: asix: ax88772_bind return error when hw_reset fail
MAINTAINERS: Update cavium networking drivers
net/mlx4_core: Fix error handling when initializing CQ bufs in the driver
net/mlx4_core: Add masking for a few queries on HCA caps
sctp: set flow sport from saddr only when it's 0
sctp: set chunk transport correctly when it's a new asoc
sctp: improve the events for sctp stream adding
sctp: improve the events for sctp stream reset
ip_tunnel: Make none-tunnel-dst tunnel port work with lwtunnel
ax25: fix possible use-after-free
sfc: suppress duplicate nvmem partition types in efx_ef10_mtd_probe
hv_netvsc: fix typos in code comments
...
The header search path -I. in kernel Makefiles is very suspicious;
it allows the compiler to search for headers in the top of $(srctree),
where obviously no header file exists.
I was able to build without this header search path.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull smb3 fixes from Steve French:
"A set of small smb3 fixes, some fixing various crediting issues
discovered during xfstest runs, five for stable"
* tag '5.0-rc3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: print CIFSMaxBufSize as part of /proc/fs/cifs/DebugData
smb3: add credits we receive from oplock/break PDUs
CIFS: Fix mounts if the client is low on credits
CIFS: Do not assume one credit for async responses
CIFS: Fix credit calculations in compound mid callback
CIFS: Fix credit calculation for encrypted reads with errors
CIFS: Fix credits calculations for reads with errors
CIFS: Do not reconnect TCP session in add_credits()
smb3: Cleanup license mess
CIFS: Fix possible hang during async MTU reads and writes
cifs: fix memory leak of an allocated cifs_ntsd structure
Pull VFIO fixes from Alex Williamson:
- cleanup licenses in new files (Thomas Gleixner)
- cleanup new compiler warnings (Alexey Kardashevskiy)
* tag 'vfio-v5.0-rc4' of git://github.com/awilliam/linux-vfio:
vfio-pci/nvlink2: Fix ancient gcc warnings
vfio/pci: Cleanup license mess
atl2_xmit_frame() should call dev_consume_skb_any() when the
transmission is successful. It makes drop profiles more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull SCSI fixes from James Bottomley:
"Six fixes, all of which appear to have user visible consequences.
The DMA one is a regression fix from the merge window and of the
others, four are driver specific and one specific to the target code"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: Use explicit access size in ufshcd_dump_regs
scsi: tcmu: fix use after free
scsi: csiostor: fix NULL pointer dereference in csio_vport_set_state()
scsi: lpfc: nvmet: avoid hang / use-after-free when destroying targetport
scsi: lpfc: nvme: avoid hang / use-after-free when destroying localport
scsi: communicate max segment size to the DMA mapping code
Pull block fixes from Jens Axboe:
"A collection of fixes for this release. This contains:
- Silence sparse rightfully complaining about non-static wbt
functions (Bart)
- Fixes for the zoned comments/ioctl documentation (Damien)
- direct-io fix that's been lingering for a while (Ernesto)
- cgroup writeback fix (Tejun)
- Set of NVMe patches for nvme-rdma/tcp (Sagi, Hannes, Raju)
- Block recursion tracking fix (Ming)
- Fix debugfs command flag naming for a few flags (Jianchao)"
* tag 'for-linus-20190125' of git://git.kernel.dk/linux-block:
block: Fix comment typo
uapi: fix ioctl documentation
blk-wbt: Declare local functions static
blk-mq: fix the cmd_flag_name array
nvme-multipath: drop optimization for static ANA group IDs
nvmet-rdma: fix null dereference under heavy load
nvme-rdma: rework queue maps handling
nvme-tcp: fix timeout handler
nvme-rdma: fix timeout handler
writeback: synchronize sync(2) against cgroup writeback membership switches
block: cover another queue enter recursion via BIO_QUEUE_ENTERED
direct-io: allow direct writes to empty inodes
wenxu says:
====================
ip_tunnel: Refactor ip_gre collect metadata xmit to ip_md_tunnel_xmit
This patchset add tunnel_dst_cache and tnl_update_pmtu feature for
ip_md_tunnel_xmit also bugfix. Then Refactor collect metatdata mode
tunnel xmit to ip_md_tunnel_xmit
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor collect metatdata mode tunnel xmit to the generic xmit function
ip_md_tunnel_xmit. It makes codes more generic and support more feture
such as pmtu_update through ip_md_tunnel_xmit
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Init the gre_key from tuninfo->key.tun_id and init the mark
from the skb->mark, set the oif to zero in the collect metadata
mode.
Fixes: cfc7381b30 ("ip_tunnel: add collect_md mode to IPIP tunnel")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tnl_update_pmtu in ip_md_tunnel_xmit to dynamic modify
the pmtu which packet send through collect_metadata mode
ip tunnel
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ip tunnel dst cache in ip_md_tunnel_xmit to make more
efficient for the route lookup.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LAN743x includes on chip One-Time-Programmable (OTP) memory.
This patch extends the ethtool EEPROM read/write interface to
access OTP memory space.
The currently existing interface is limited, as it does not
allow OTP read, and OTP writes are restricted to
offset==0, length==512, and data[0]==0xF3.
This patch removes these restrictions and adds a private flag
called OTP_ACCESS, which is used to switch between EEPROM, and
OTP modes.
The private flag OTP_ACCESS is configurable through the
ethtool --set-priv-flags command.
And visible through the
ethtool --show-priv-flags command.
By default OTP_ACCESS is false, and there for previously existing
EEPROM commands will work exactly the same. However now access to
OTP requires one extra step of setting OTP_ACCESS to true. This
flag controls the read, write, and length reporting, functions
of ethtool.
EEPROM presence is not checked when setting or clearing this flag.
If the EEPROM is not present, the user, as before, will need to
diagnose that using existing read and write function of ethtool,
while OTP_ACCESS is false.
Updates for V2:
Added comments as to why this patch is needed.
Added comments explaining that EEPROM presence is not check
when setting or clearing the OTP_ACCESS flag.
Added length checking to all otp/eeprom read/write functions.
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan says:
====================
code optimizations & bugfixes for HNS3 driver
This patchset includes bugfixes and code optimizations for the HNS3
ethernet controller driver
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
VF can receive packets of other functions when in promisc
mode. It's not safe, so don't allow VF to enable promisc
mode.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds initialization for nic state, sets flag
HNS3_NIC_STATE_DOWN when initialize, clears it before
vectors and napi being enabled in the hns3_nic_net_up(),
and sets it back in the error handler.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A single transmit packet can span up to 8 descriptors according
to the HW limit. If a skb has more than 8 frags, driver uses
skb_copy to get a new skb which has less frags.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hns3_client_setup_tc in enet is for updating TC configuration to
stack, and hclge_setup_tc in hclge_dcb is mainly for setting the
configuration to hardware.
This patch removes the hns3_nic_set_real_num_queue from
hns3_setup_tc in enet, and call hclge_client_setup_tc to update
TC configuration to stack with netdev down, because the netdev
down operation is done in hclge_dcb now.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After doing down/uninit/init/up in hclge_dcb, it is not necessary
to call dcb_ops->map_update in enet, so hclge_map_update can be
called directly in hclge_dcb.
This is for preparing to call hns3_nic_set_real_num_queue with
netdev down when user changes mqprio configuration.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When user changes the mqprio configuration, enet need to be
uninited and inited besides down'ed and up'ed, because the queue
num may change when the TC num changes.
Also, it is more suitable to do the down/unint/init/up operation
in hclge module using hclge_notify_client, because this config
change may affect PF and its VF.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After setting the serdes loopback, you need to determine
the status of the MAC negotiation. If a status exception
is obtained after 200ms, a timeout error is returned.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For revision 0x20, vlan filter is always bypassed when enable
broadcast promisc mode. In this case, broadcast packets with
any vlan id can be accpeted. We should disable broadcast promisc
mode until user want enable it.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In current code, it always return 0, even loopback mode setting failed.
It's incorrect. This patch fixes return value handle for loopback test.
Fixes: 0f29fc23b2 ("net: hns3: Fix for loopback selftest failed problem")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently hclge_ieee_setets returns error directly when there is
error, which may cause netdev not up problem.
This patch adds some error handling when setting ETS configuration
fails.
Fixes: cacde272dd ("net: hns3: Add hclge_dcb module for the support of DCB feature")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit says:
====================
r8169: add EEE support for RTL8168f
This series adds EEE support for RTL8168f. Again first patch adds the
support, and second patch enables EEE per default.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
