During the driver conversion to shmem, the start address for the
scanout buffer was set to the base PCI address.
In most cases it works because only the lower 24bits are used, and
due to alignment it was almost always 0.
But on some unlucky hardware, it's not the case, and some uninitialized
memory is displayed on the BMC.
With shmem, the primary plane is always at offset 0 in GPU memory.
* v2: rewrite the patch to set the offset to 0. (Thomas Zimmermann)
* v3: move the change to plane_init() and also fix the cursor plane.
(Jammy Huang)
Tested on a sr645 affected by this bug.
Fixes: f2fa5a99ca ("drm/ast: Convert ast to SHMEM")
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jammy Huang <jammy_huang@aspeedtech.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230209094417.21630-1-jfalempe@redhat.com
When a fbdev with deferred I/O is once opened and closed, the dirty
pages still remain queued in the pageref list, and eventually later
those may be processed in the delayed work. This may lead to a
corruption of pages, hitting an Oops.
This patch makes sure to cancel the delayed work and clean up the
pageref list at closing the device for addressing the bug. A part of
the cleanup code is factored out as a new helper function that is
called from the common fb_release().
Reviewed-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Miko Larsson <mikoxyzzz@gmail.com>
Fixes: 56c134f7f1 ("fbdev: Track deferred-I/O pages in pageref struct")
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230129082856.22113-1-tiwai@suse.de
The formula that determines the core clock requirement based on pixel
clock and blanking has been determined experimentally to minimise the
clock while supporting all modes we've seen.
A new reduced blanking mode (4kp60 at 533MHz rather than the standard
594MHz) has been seen that doesn't produce a high enough clock and
results in "flip_done timed out" error.
Increase the setup cost in the formula to make this work. The result is
a reduced blanking mode increases by up to 7MHz while leaving the
standard timing
mode untouched
Link: https://github.com/raspberrypi/linux/issues/4446
Fixes: 16e101051f ("drm/vc4: Increase the core clock based on HVS load")
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20230127145558.446123-1-maxime@cerno.tech
Issue is some displays go blank at the point of firmware to kms
handover. Plugging/unplugging hdmi cable, power cycling display, or
switching standby off/on
typically resolve this case.
Finally managed to find a display that suffers from this, and track down
the issue.
The firmware uses AVMUTE in normal operation. It will set AVMUTE before
disabling hdmi clocks and phy. It will clear AVMUTE after clocks and phy
are set up for a new hdmi mode.
But with the hdmi handover from firmware to kms, AVMUTE will be set by
firmware.
kms driver typically has no GCP packet (except for deep colour modes).
The spec isn't clear on whether to consider the AVMUTE as continuing
indefinitely in the absence of a GCP packet, or to consider that state
to have ended.
Most displays behave as we want, but there are a number (from multiple
manufacturers) which need to see AVMUTE cleared before displaying a
picture.
Lets just always enable GCP packet with AVMUTE cleared. That resolves
the issue on problematic displays.
From HDMI 1.4 spec:
A CD field of zero (Color Depth not indicated) shall be used whenever
the Sink does not indicate support for Deep Color. This value may
also be used in Deep Color mode to transmit a GCP indicating only
non-Deep Color information (e.g. AVMUTE).
So use CD=0 where we were previously not enabling a GCP.
Link: https://forum.libreelec.tv/thread/24780-le-10-0-1-rpi4-no-picture-after-update-from-le-10-0-0
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20230127161219.457058-1-maxime@cerno.tech
YUV images can either be presented as one allocation with offsets
for the different planes, or multiple allocations with 0 offsets.
The driver only ever calls drm_fb_[dma|cma]_get_gem_obj with plane
index 0, therefore any application using the second approach was
incorrectly rendered.
Correctly determine the address for each plane, removing the
assumption that the base address is the same for each.
Fixes: fc04023faf ("drm/vc4: Add support for YUV planes.")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20230127155708.454704-1-maxime@cerno.tech
We reference dump buffers both by their handle as well as their
object. The problem is now that when anybody iterates over the DRM
framebuffers and exports the underlying GEM objects through DMA-buf
we run into a circular reference count situation.
The result is that the fbdev handling holds the GEM handle preventing
the DMA-buf in the GEM object to be released. This DMA-buf in turn
holds a reference to the driver module which on unload would release
the fbdev.
Break that loop by releasing the handle as soon as the DRM
framebuffer object is created. The DRM framebuffer and the DRM client
buffer structure still hold a reference to the underlying GEM object
preventing its destruction.
Signed-off-by: Christian König <christian.koenig@amd.com>
Fixes: c76f0f7cb5 ("drm: Begin an API for in-kernel clients")
Cc: <stable@vger.kernel.org>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230126102814.8722-1-christian.koenig@amd.com
An interrupted dma_fence_wait() becomes an -ERESTARTSYS returned
to userspace ioctl(DRM_IOCTL_VIRTGPU_EXECBUFFER) calls, prompting to
retry the ioctl(), but the passed exbuf->fence_fd has been reset to -1,
making the retry attempt fail at sync_file_get_fence().
The uapi for DRM_IOCTL_VIRTGPU_EXECBUFFER is changed to retain the
passed value for exbuf->fence_fd when returning anything besides a
successful result from the ioctl.
Fixes: 2cd7b6f08b ("drm/virtio: add in/out fence support for explicit synchronization")
Signed-off-by: Ryan Neph <ryanneph@chromium.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230203233345.2477767-1-ryanneph@chromium.org
The unprepare sequence has started to fail after moving to panel bridge
code in the msm drm driver (commit 007ac0262b ("drm/msm/dsi: switch to
DRM_PANEL_BRIDGE")). You'll see messages like this in the kernel logs:
panel-boe-tv101wum-nl6 ae94000.dsi.0: failed to set panel off: -22
This is because boe_panel_enter_sleep_mode() needs an operating DSI link
to set the panel into sleep mode. Performing those writes in the
unprepare phase of bridge ops is too late, because the link has already
been torn down by the DSI controller in post_disable, i.e. the PHY has
been disabled, etc. See dsi_mgr_bridge_post_disable() for more details
on the DSI .
Split the unprepare function into a disable part and an unprepare part.
For now, just the DSI writes to enter sleep mode are put in the disable
function. This fixes the panel off routine and keeps the panel happy.
My Wormdingler has an integrated touchscreen that stops responding to
touch if the panel is only half disabled too. This patch fixes it. And
finally, this saves power when the screen is off because without this
fix the regulators for the panel are left enabled when nothing is being
displayed on the screen.
Fixes: 007ac0262b ("drm/msm/dsi: switch to DRM_PANEL_BRIDGE")
Fixes: a869b9db7a ("drm/panel: support for boe tv101wum-nl6 wuxga dsi video mode panel")
Cc: yangcong <yangcong5@huaqin.corp-partner.google.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Jitao Shi <jitao.shi@mediatek.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Rob Clark <robdclark@chromium.org>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230106030108.2542081-1-swboyd@chromium.org
(cherry picked from commit c913cd5489)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Starting from Turing, the driver is no longer responsible for initiating
DEVINIT when required as the GPU started loading a FW image from ROM and
executing DEVINIT itself after power-on.
However - we apparently still need to wait for it to complete.
This should correct some issues with runpm on some systems, where we get
control of the HW before it's been fully reinitialised after resume from
suspend.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230130223715.1831509-1-bskeggs@redhat.com
Commit 622113b9f1 ("drm/ssd130x: Replace simple display helpers with the
atomic helpers") changed the driver to just use the atomic helpers instead
of the simple KMS abstraction layer.
But the commit also made a subtle change on the display power sequence and
initialization order, by moving the ssd130x_power_on() call to the encoder
.atomic_enable handler and the ssd130x_init() call to CRTC .reset handler.
Before this change, both ssd130x_power_on() and ssd130x_init() were called
in the simple display pipeline .enable handler, so the display was already
initialized by the time the SSD130X_DISPLAY_ON command was sent.
For some reasons, it only made the ssd130x SPI driver to fail but the I2C
was still working. That is the reason why the bug was not noticed before.
To revert to the old driver behavior, move the ssd130x_init() call to the
encoder .atomic_enable as well. Besides fixing the panel not being turned
on when using SPI, it also gets rid of the custom CRTC .reset callback.
Fixes: 622113b9f1 ("drm/ssd130x: Replace simple display helpers with the atomic helpers")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230125184230.3343206-1-javierm@redhat.com
The DRM fbdev emulation layer sets the struct fb_info .fbdefio field to
a struct fb_deferred_io pointer, that is shared across all drivers that
use the generic drm_fbdev_generic_setup() helper function.
It is a problem because the fbdev core deferred I/O logic assumes that
the struct fb_deferred_io data is not shared between devices, and it's
stored there state such as the list of pages touched and a mutex that
is use to synchronize between the fb_deferred_io_track_page() function
that track the dirty pages and fb_deferred_io_work() workqueue handler
doing the actual deferred I/O.
The latter can lead to the following error, since it may happen that two
drivers are probed and then one is removed, which causes the mutex bo be
destroyed and not existing anymore by the time the other driver tries to
grab it for the fbdev deferred I/O logic:
[ 369.756553] ------------[ cut here ]------------
[ 369.756604] DEBUG_LOCKS_WARN_ON(lock->magic != lock)
[ 369.756631] WARNING: CPU: 2 PID: 1023 at kernel/locking/mutex.c:582 __mutex_lock+0x348/0x424
[ 369.756744] Modules linked in: nf_conntrack_netbios_ns nf_conntrack_broadcast nft_fib_inet nft_fib_ipv4 nft_fib_ipv6 nft_fib nft_reject_inet nf_reject_ipv4 nf_reject_ipv6 nft_reject nft_ct nft_chain_nat nf_nat nf_conntrack nf_defrag_ip
v6 nf_defrag_ipv4 ip_set nf_tables nfnetlink qrtr btsdio bluetooth sunrpc brcmfmac snd_soc_hdmi_codec cpufreq_dt cfg80211 vfat fat vc4 rfkill brcmutil raspberrypi_cpufreq i2c_bcm2835 iproc_rng200 bcm2711_thermal snd_soc_core snd_pcm_dmaen
gine leds_gpio nvmem_rmem joydev hid_cherry uas usb_storage gpio_raspberrypi_exp v3d snd_pcm raspberrypi_hwmon gpu_sched bcm2835_wdt broadcom bcm_phy_lib snd_timer genet snd mdio_bcm_unimac clk_bcm2711_dvp soundcore drm_display_helper pci
e_brcmstb cec ip6_tables ip_tables fuse
[ 369.757400] CPU: 2 PID: 1023 Comm: fbtest Not tainted 5.19.0-rc6+ #94
[ 369.757455] Hardware name: raspberrypi,4-model-b Raspberry Pi 4 Model B Rev 1.4/Raspberry Pi 4 Model B Rev 1.4, BIOS 2022.10 10/01/2022
[ 369.757538] pstate: 00400005 (nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 369.757596] pc : __mutex_lock+0x348/0x424
[ 369.757635] lr : __mutex_lock+0x348/0x424
[ 369.757672] sp : ffff80000953bb00
[ 369.757703] x29: ffff80000953bb00 x28: ffff17fdc087c000 x27: 0000000000000002
[ 369.757771] x26: ffff17fdc349f9b0 x25: fffffc5ff72e0100 x24: 0000000000000000
[ 369.757838] x23: 0000000000000000 x22: 0000000000000002 x21: ffffa618df636f10
[ 369.757903] x20: ffff80000953bb68 x19: ffffa618e0f18138 x18: 0000000000000001
[ 369.757968] x17: 0000000020000000 x16: 0000000000000002 x15: 0000000000000000
[ 369.758032] x14: 0000000000000000 x13: 284e4f5f4e524157 x12: 5f534b434f4c5f47
[ 369.758097] x11: 00000000ffffdfff x10: ffffa618e0c79f88 x9 : ffffa618de472484
[ 369.758162] x8 : 000000000002ffe8 x7 : c0000000ffffdfff x6 : 00000000000affa8
[ 369.758227] x5 : 0000000000001fff x4 : 0000000000000000 x3 : 0000000000000027
[ 369.758292] x2 : 0000000000000001 x1 : ffff17fdc087c000 x0 : 0000000000000028
[ 369.758357] Call trace:
[ 369.758383] __mutex_lock+0x348/0x424
[ 369.758420] mutex_lock_nested+0x4c/0x5c
[ 369.758459] fb_deferred_io_mkwrite+0x78/0x1d8
[ 369.758507] do_page_mkwrite+0x5c/0x19c
[ 369.758550] wp_page_shared+0x70/0x1a0
[ 369.758590] do_wp_page+0x3d0/0x510
[ 369.758628] handle_pte_fault+0x1c0/0x1e0
[ 369.758670] __handle_mm_fault+0x250/0x380
[ 369.758712] handle_mm_fault+0x17c/0x3a4
[ 369.758753] do_page_fault+0x158/0x530
[ 369.758792] do_mem_abort+0x50/0xa0
[ 369.758831] el0_da+0x78/0x19c
[ 369.758864] el0t_64_sync_handler+0xbc/0x150
[ 369.758904] el0t_64_sync+0x190/0x194
[ 369.758942] irq event stamp: 11395
[ 369.758973] hardirqs last enabled at (11395): [<ffffa618de472554>] __up_console_sem+0x74/0x80
[ 369.759042] hardirqs last disabled at (11394): [<ffffa618de47254c>] __up_console_sem+0x6c/0x80
[ 369.760554] softirqs last enabled at (11392): [<ffffa618de330a74>] __do_softirq+0x4c4/0x6b8
[ 369.762060] softirqs last disabled at (11383): [<ffffa618de3c9124>] __irq_exit_rcu+0x104/0x214
[ 369.763564] ---[ end trace 0000000000000000 ]---
Fixes: d536540f30 ("drm/fb-helper: Add generic fbdev emulation .fb_probe function")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230121192418.2814955-4-javierm@redhat.com
On ARMv5 and earlier, a randconfig build can still run into
WARNING: unmet direct dependencies detected for IOMMU_IO_PGTABLE_LPAE
Depends on [n]: IOMMU_SUPPORT [=y] && (ARM [=y] || ARM64 || COMPILE_TEST [=y]) && !GENERIC_ATOMIC64 [=y]
Selected by [y]:
- DRM_PANFROST [=y] && HAS_IOMEM [=y] && DRM [=y] && (ARM [=y] || ARM64 || COMPILE_TEST [=y] && !GENERIC_ATOMIC64 [=y]) && MMU [=y]
Rework the dependencies to always require a working cmpxchg64.
Fixes: db594ba3fc ("drm/panfrost: depend on !GENERIC_ATOMIC64 when using COMPILE_TEST")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230117164456.1591901-1-arnd@kernel.org
Commit 374146cad4 ("drm/vc4: Switch to drmm_mutex_init") converted,
among other functions, vc4_create_object() to use drmm_mutex_init().
However, that function is used to allocate a BO, and therefore the
mutex needs to be freed much sooner than when the DRM device is removed
from the system.
For each buffer allocation we thus end up allocating a small structure
as part of the DRM-managed mechanism that is never freed, eventually
leading us to no longer having any free memory anymore.
Let's switch back to mutex_init/mutex_destroy to deal with it properly.
Fixes: 374146cad4 ("drm/vc4: Switch to drmm_mutex_init")
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20230112091243.490799-1-maxime@cerno.tech
User resource lookups used rcu to avoid two extra atomics. Unfortunately
the rcu paths were buggy and it was easy to make the driver crash by
submitting command buffers from two different threads. Because the
lookups never show up in performance profiles replace them with a
regular spin lock which fixes the races in accesses to those shared
resources.
Fixes kernel oops'es in IGT's vmwgfx execution_buffer stress test and
seen crashes with apps using shared resources.
Fixes: e14c02e6b6 ("drm/vmwgfx: Look up objects without taking a reference")
Signed-off-by: Zack Rusin <zackr@vmware.com>
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Reviewed-by: Maaz Mombasawala <mombasawalam@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221207172907.959037-1-zack@kde.org
The drm_sched_entity_kill() is invoked twice by drm_sched_entity_destroy()
while userspace process is exiting or being killed. First time it's invoked
when sched entity is flushed and second time when entity is released. This
causes a lockup within wait_for_completion(entity_idle) due to how completion
API works.
Calling wait_for_completion() more times than complete() was invoked is a
error condition that causes lockup because completion internally uses
counter for complete/wait calls. The complete_all() must be used instead
in such cases.
This patch fixes lockup of Panfrost driver that is reproducible by killing
any application in a middle of 3d drawing operation.
Fixes: 2fdb8a8f07 ("drm/scheduler: rework entity flush, kill and fini")
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Tested-by: Guilherme G. Piccoli <gpiccoli@igalia.com> # Steam Deck
Link: https://patchwork.freedesktop.org/patch/msgid/20221123001303.533968-1-dmitry.osipenko@collabora.com
The drm_sched_entity_kill() is invoked twice by drm_sched_entity_destroy()
while userspace process is exiting or being killed. First time it's invoked
when sched entity is flushed and second time when entity is released. This
causes a lockup within wait_for_completion(entity_idle) due to how completion
API works.
Calling wait_for_completion() more times than complete() was invoked is a
error condition that causes lockup because completion internally uses
counter for complete/wait calls. The complete_all() must be used instead
in such cases.
This patch fixes lockup of Panfrost driver that is reproducible by killing
any application in a middle of 3d drawing operation.
Fixes: 2fdb8a8f07 ("drm/scheduler: rework entity flush, kill and fini")
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Tested-by: Guilherme G. Piccoli <gpiccoli@igalia.com> # Steam Deck
Link: https://patchwork.freedesktop.org/patch/msgid/20221123001303.533968-1-dmitry.osipenko@collabora.com
Having a bigger number of FIFO lines held after vsync is only useful to
SoCs using AFBC to give time to the AFBC decoder to be reset, configured
and enabled again.
For SoCs not using AFBC this, on the contrary, is causing on some
displays issues and a few pixels vertical offset in the displayed image.
Conditionally increase the number of lines held after vsync only for
SoCs using AFBC, leaving the default value for all the others.
Fixes: 24e0d4058e ("drm/meson: hold 32 lines after vsync to give time for AFBC start")
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
[narmstrong: added fixes tag]
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221216-afbc_s905x-v1-0-033bebf780d9@baylibre.com
Pull perf fixes from Borislav Petkov:
- Pass only an initialized perf event attribute to the LSM hook
- Fix a use-after-free on the perf syscall's error path
- A potential integer overflow fix in amd_core_pmu_init()
- Fix the cgroup events tracking after the context handling rewrite
- Return the proper value from the inherit_event() function on error
* tag 'perf_urgent_for_v6.2_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Call LSM hook after copying perf_event_attr
perf: Fix use-after-free in error path
perf/x86/amd: fix potential integer overflow on shift of a int
perf/core: Fix cgroup events tracking
perf core: Return error pointer if inherit_event() fails to find pmu_ctx
Pull x86 fixes from Borislav Petkov:
- Two fixes to correct how kprobes handles INT3 now that they're added
by other functionality like the rethunks and not only kgdb
- Remove __init section markings of two functions which are referenced
by a function in the .text section
* tag 'x86_urgent_for_v6.2_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/kprobes: Fix optprobe optimization check with CONFIG_RETHUNK
x86/kprobes: Fix kprobes instruction boudary check with CONFIG_RETHUNK
x86/calldepth: Fix incorrect init section references
Pull locking fixes from Borislav Petkov:
- Prevent the leaking of a debug timer in futex_waitv()
- A preempt-RT mutex locking fix, adding the proper acquire semantics
* tag 'locking_urgent_for_v6.2_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
futex: Fix futex_waitv() hrtimer debug object leak on kcalloc error
rtmutex: Add acquire semantics for rtmutex lock acquisition slow path
Pull drm fixes from Daniel Vetter:
"I'm just back from the mountains, and Dave is out at the beach and
should be back in a week again. Just i915 fixes and since Rodrigo
bothered to make the pull last week I figured I should warm up gpg and
forward this in a nice signed tag as a new years present!
- i915 fixes for newer platforms
- i915 locking rework to not give up in vm eviction fallback path too
early"
* tag 'drm-fixes-2023-01-01' of git://anongit.freedesktop.org/drm/drm:
drm/i915/dsi: fix MIPI_BKLT_EN_1 native GPIO index
drm/i915/dsi: add support for ICL+ native MIPI GPIO sequence
drm/i915/uc: Fix two issues with over-size firmware files
drm/i915: improve the catch-all evict to handle lock contention
drm/i915: Remove __maybe_unused from mtl_info
drm/i915: fix TLB invalidation for Gen12.50 video and compute engines
Pull Kbuild fixes from Masahiro Yamada:
- Fix broken BuildID
- Add srcrpm-pkg to the help message
- Fix the option order for modpost built with musl libc
- Fix the build dependency of rpm-pkg for openSUSE
* tag 'kbuild-fixes-v6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
fixdep: remove unneeded <stdarg.h> inclusion
kbuild: sort single-targets alphabetically again
kbuild: rpm-pkg: add libelf-devel as alternative for BuildRequires
kbuild: Fix running modpost with musl libc
kbuild: add a missing line for help message
.gitignore: ignore *.rpm
arch: fix broken BuildID for arm64 and riscv
kconfig: Add static text for search information in help menu
