Sometimes, BB might encounter RX problem on OFDM 6M. It's not quite
easy to happen, but if it happens, we will keep getting stuck on RX.
And, since we cannot properly receive layer 2 ACK, it also casues TX
problem, e.g. constantly retrying TX. Eventually, after some time, we
would get disconnected due to abnormal behavior.
Update break setting and phy status parsing time to make BB get out
of stuck state faster.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220704023453.19935-3-pkshih@realtek.com
Without this patch, our hardware attempts to perform dma while device
cpu restarts, and leads to iommu page faults caused by invalid requests.
Some platforms show warning messages as below:
rtw89_8852ce 0000:01:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT
domain=0x000a address=0x10000000004 flags=0x0030]
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220704023453.19935-2-pkshih@realtek.com
In current flow, FW is asynchronously loaded after alloc_hw(). It defers
the decision on FW feature map. It makes things difficult for us to decide
whether to hook chanctx ops, which should be decided while alloc_hw() is
calling. Still, asynchronous gets its advantages. So, we want to resolve
this without dropping them.
Based on multi-FW flag, RTW89_MFW_SIG, we can determine runtime FW is
multi-FW (MFW) or single FW (SFW). Both of them have a quite small chunk
for header at the head. The difference is that MFW doesn't describe version
code in its header while SFW does. So, we plan to extend MFW header for
version code. After that, in both cases, we can determine FW feature map by
just FW header. And, according to the map, we can decide chanctx.
So, we call request_partial_firmware_into_buf() to request a quite small
chunk before alloc_hw() to get a early FW feature map without affecting
things much and only use early map to decide whether to hook chanctx ops.
It means that if non-extended MFW is used at runtime, driver just acts
without chanctx as before. If extended MFW or SFW, which supports required
FW features, is used at runtime, driver can hook chanctx ops to mac80211 if
chip has configured support_chanctx_num > 0.
Besides, key point for now to support single one chanctx is whether HW scan
is supported at runtime. So, we configure all chip's support_chanctx_num to
1, and check if HW scan is supported at runtime via early FW feature map.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-14-pkshih@realtek.com
Some HW features are required if we hook chanctx ops to mac80211. With it,
mac80211 would expect the HW-supported variant ops exists on some behavior,
e.g. HW scan. But, HW features may depend on chip's FW or its development.
Besides, how many chanctx can be supported also depends on chip design.
We can neither decide whether to generally support chanctx ops nor how many
chanctx can be supported.
So, support_chanctx_num is added under chip info to deal with this by chip.
For now, all chip configure support_chanctx_num as 0. We haven't really
hook chanctx ops yet. So, chip can run without mac80211 chanctx as before.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-13-pkshih@realtek.com
Support mac80211 chanctx series ops. Still, currently support
single channel. Based on this premise, things should be similar
to before. So, we haven't dealt with relationship between vif
and chanctx in depth. Instead, we leave both ::assign_vif()
and ::unassign_vif() as noops for now.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-12-pkshih@realtek.com
After supporting more than one channel, we need entity mode to decide
how to set current channel(s) on the sub-entities. This decision may
happen on set_channel() and rtw89_core_set_chip_txpwr().
For now, we support single one channel and use only first HW entry,
i.e. RTW89_SUB_ENTITY_0, RTW89_MAC_0, RTW89_PHY_0. Without something
unexpected, the entity mode should always be RTW89_ENT_MODE_SCC after
recalcated, where SCC means single channel concurrency. So, an assert
is added in set_channel() and rtw89_core_set_chip_txpwr().
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-11-pkshih@realtek.com
While idle, we need a default chandef to set channel for things,
such as scan. Before support of mac80211 chanctx, mac80211 would
configure a default one on ieee80211_hw::conf::chandef. And we
just queried it whenever we did set channel. However, after support
of mac80211 chanctx, the flow won't work like before.
Besides, we don't now query chandef from ieee80211_hw::conf::chandef
either. So, similar to mac80211 without using chanctx, we configure
the default chandef with ieee80211_channel of index 0 in 2GHz.
Although we have not added the support of mac80211 chanctx here,
this configuration should be compatible before that. So, we commit
this ahead.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-10-pkshih@realtek.com
Originally, we didn't support mac80211 chanctx, so it's expected that
ieee80211_hw::conf::chandef would be filled by mac80211. And then, we
could just query it whenever we need the current chandef.
However, we are planing to support mac80211 chanctx. After that, the
above assumption would be broken. So, we adjust a bit ahead to reduce
future works about mac80211 chanctx.
After this, we don't query ieee80211_hw::conf::chandef directly, and
we add a map, entity_map, to HAL to indicate which chandef came from
stack. And it will later be used to recalcate entity mode.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-9-pkshih@realtek.com
For future support on multiple channels by multiple sub-entities,
we need to manage parameters of each channel instance like rtw89_chan,
rtw89_mac_idx, rtw89_phy_idx. So, we adjust related channel callback
functions and centrally conrtol these parameters in set_channel().
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-8-pkshih@realtek.com
For future support on multiple channels, it would be disturbing if we
still allow scattered leaf functions of TX power to query and manage
channel related control by themselves.
So, query rtw89_chan only on top functions. Then, pass it via functions
to make sure that the values coming from the same struct rtw89_chan.
Besides, fix rtw8852a_set_txpwr_offset() from rtw8852a_set_txpwr_ctrl()
to rtw8852a_set_txpwr(). TX power offset should consider current band,
so move it to chip_ops::set_txpwr() which will be called every time that
channel is set.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-6-pkshih@realtek.com
Sometimes we need to write current rtw89_chan outside set_channel(),
e.g. during HW scan, we adjust it to align FW process through C2H.
However, we don't have full parameters to fill entire rtw89_chan.
And it will breakage if we update only part of current rtw89_chan.
That is what we don't want to see because most flows throughout
driver treat rtw89_chan as a whole.
So, we divide struct rtw89_chan to basic part and derived part. The
basic part contains the parameters which we are always able to know.
And the derived part will be calculated by the basic part. Then, a
central function, rtw89_chan_create(), is added to deal with this.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-5-pkshih@realtek.com
We are planning to support mac80211 chanctx. To reduce future works,
the driver architecture is adjusted first to isolate related things.
According to chip, our HW may have multiple sub-entities to support
multiple mac80211 chanctx. Struct rtw89_chan has been introduced for
things about channel/band/subband/... Now introduce struct rtw89_chan_rcd
to record difference after assigning new one of struct rtw89_chan.
We will implement and support chanctx with single channel first, i.e.
only use entry in RTW89_SUB_ENTITY_0, before handling dual channels.
Our hierarchy in planning will become as the following.
DEV
-> HAL
---> entity (manage status across sub-entities)
-----> sub-entity[*] (support mac80211 chanctx)
where each sub-entity contains one struct rtw89_chan.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-4-pkshih@realtek.com
Introduce struct rtw89_chan ahead to encapsulate stuffs from struct
rtw89_channel_params. These stuffs have a clone in HAL and are used
throughout driver. After multiple channels support, it's expected that
each channel instance has a configuration of them. So, we refine them
with struct rtw89_chan by precise type first, and will re-arrange HAL
by struct rtw89_chan in the following as well.
(No logic has changed.)
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-3-pkshih@realtek.com
We need to invoke the callback of the changed band at the first
set_channel() after every power-off. Originally, we forced the
channel to be 0 when doing power-off, and then determined things
by comparing channel with 0.
However, deciding on such things by channel might be confusing.
It's also confusing to use this kind of decision when we consider
multiple channels in the follow-up patches. So, another flag,
entity_active, is added ahead to HAL to deal with this.
Besides, we also need to check if entity is active when we set
TX power.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-2-pkshih@realtek.com
syzbot is reporting uninit value at ath9k_htc_rx_msg() [1], for
ioctl(USB_RAW_IOCTL_EP_WRITE) can call ath9k_hif_usb_rx_stream() with
pkt_len = 0 but ath9k_hif_usb_rx_stream() uses
__dev_alloc_skb(pkt_len + 32, GFP_ATOMIC) based on an assumption that
pkt_len is valid. As a result, ath9k_hif_usb_rx_stream() allocates skb
with uninitialized memory and ath9k_htc_rx_msg() is reading from
uninitialized memory.
Since bytes accessed by ath9k_htc_rx_msg() is not known until
ath9k_htc_rx_msg() is called, it would be difficult to check minimal valid
pkt_len at "if (pkt_len > 2 * MAX_RX_BUF_SIZE) {" line in
ath9k_hif_usb_rx_stream().
We have two choices. One is to workaround by adding __GFP_ZERO so that
ath9k_htc_rx_msg() sees 0 if pkt_len is invalid. The other is to let
ath9k_htc_rx_msg() validate pkt_len before accessing. This patch chose
the latter.
Note that I'm not sure threshold condition is correct, for I can't find
details on possible packet length used by this protocol.
Link: https://syzkaller.appspot.com/bug?extid=2ca247c2d60c7023de7f [1]
Reported-by: syzbot <syzbot+2ca247c2d60c7023de7f@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/7acfa1be-4b5c-b2ce-de43-95b0593fb3e5@I-love.SAKURA.ne.jp
Johannes berg says:
====================
Various updates:
* rtw88: operation, locking, warning, and code style fixes
* rtw89: small updates
* cfg80211/mac80211: more EHT/MLO (802.11be, WiFi 7) work
* brcmfmac: a couple of fixes
* misc cleanups etc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The Lenovo OneLink+ Dock contains an RTL8153 controller that behaves as
a broken CDC device by default. Add the custom Lenovo PID to the r8152
driver to support it properly.
Also, systems compatible with this dock provide a BIOS option to enable
MAC address passthrough (as per Lenovo document "ThinkPad Docking
Solutions 2017"). Add the custom PID to the MAC passthrough list too.
Tested on a ThinkPad 13 1st gen with the expected results:
passthrough disabled: Invalid header when reading pass-thru MAC addr
passthrough enabled: Using pass-thru MAC addr XX:XX:XX:XX:XX:XX
Signed-off-by: Jean-Francois Le Fillatre <jflf_kernel@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-08-24 (ice)
This series contains updates to ice driver only.
Marcin adds support for TC parsing on TTL and ToS fields.
Anatolli adds support for devlink port split command to allow
configuration of various port configurations.
Jake allows for passing and writing an additional NVM write activate
field by expanding current cmd_flag.
Ani makes PHY debug output more readable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
clang reports uninitialized use:
>> drivers/net/wireless/realtek/rtw88/main.c:731:2: warning: variable
'primary_channel_idx' is used uninitialized whenever switch default is
taken [-Wsometimes-uninitialized]
default:
^~~~~~~
drivers/net/wireless/realtek/rtw88/main.c:754:39: note: uninitialized
use occurs here
hal->current_primary_channel_index = primary_channel_idx;
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/realtek/rtw88/main.c:687:24: note: initialize the
variable 'primary_channel_idx' to silence this warning
u8 primary_channel_idx;
^
= '\0'
This situation could not happen, because possible channel bandwidth
20/40/80MHz are enumerated.
Fixes: 341dd1f7de ("wifi: rtw88: add the update channel flow to support setting by parameters")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20220815062004.22920-1-pkshih@realtek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As per RGMII specification v2.0, section 3.4.1, RGMII/RTBI has an
optional in-band status feature where the PHY's link status, speed and
duplex mode can be passed to the MAC.
Allow RGMII/RTBI to use in-band status.
Signed-off-by: Qingfang DENG <dqfext@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maksym Glubokiy says:
====================
net: prestera: matchall features
This patch series extracts matchall rules management out of SPAN API
implementation and adds 2 features on top of that:
- support for egress traffic (mirred egress action)
- proper rule priorities management between matchall and flower
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
matchall rules can be added only to chain 0 and their priorities have
limitations:
- new matchall ingress rule's priority must be higher (lower value)
than any existing flower rule;
- new matchall egress rule's priority must be lower (higher value)
than any existing flower rule.
The opposite works for flower rule adding:
- new flower ingress rule's priority must be lower (higher value)
than any existing matchall rule;
- new flower egress rule's priority must be higher (lower value)
than any existing matchall rule.
This is a hardware limitation and thus must be properly handled in
driver by reporting errors to the user when newly added rule has such a
priority that cannot be installed into the hardware.
To achieve this, the driver must maintain both min/max matchall
priorities for every flower block when user adds/deletes a matchall
rule, as well as both min/max flower priorities for chain 0 for every
adding/deletion of flower rules for chain 0.
Cc: Serhiy Boiko <serhiy.boiko@plvision.eu>
Signed-off-by: Maksym Glubokiy <maksym.glubokiy@plvision.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds more clarity to handling of TC_CLSMATCHALL_REPLACE and
TC_CLSMATCHALL_DESTROY events by calling newly added *_mall_*() handlers
instead of directly calling SPAN API.
This also extracts matchall rules management out of SPAN API since SPAN
is a hardware module which is used to implement 'matchall egress mirred'
action only.
Signed-off-by: Taras Chornyi <tchornyi@marvell.com>
Signed-off-by: Serhiy Boiko <serhiy.boiko@plvision.eu>
Signed-off-by: Maksym Glubokiy <maksym.glubokiy@plvision.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some exotic ax88772 based devices which may require
functionality provide by the phylink framework. For example:
- US100A20SFP, USB 2.0 auf LWL Converter with SFP Cage
- AX88772B USB to 100Base-TX Ethernet (with RMII) demo board, where it
is possible to switch between internal PHY and external RMII based
connection.
So, convert this driver to phylink as soon as possible.
Tested with:
- AX88772A + internal PHY
- AX88772B + external DP83TD510E T1L PHY
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we add 6 GHz capability in MLO, we cannot use the SMPS
mode from the deflink. Pass it separately instead since on
a second link we don't even have a link data struct yet.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use try_cmpxchg instead of cmpxchg (*ptr, old, new) == old in
napi_if_scheduled_mark_missed. x86 CMPXCHG instruction returns
success in ZF flag, so this change saves a compare after cmpxchg
(and related move instruction in front of cmpxchg).
Also, try_cmpxchg implicitly assigns old *ptr value to "old" when cmpxchg
fails, enabling further code simplifications.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Link: https://lore.kernel.org/r/20220822143243.2798-1-ubizjak@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull networking fixes from Jakub Kicinski:
"Including fixes from ipsec and netfilter (with one broken Fixes tag).
Current release - new code bugs:
- dsa: don't dereference NULL extack in dsa_slave_changeupper()
- dpaa: fix <1G ethernet on LS1046ARDB
- neigh: don't call kfree_skb() under spin_lock_irqsave()
Previous releases - regressions:
- r8152: fix the RX FIFO settings when suspending
- dsa: microchip: keep compatibility with device tree blobs with no
phy-mode
- Revert "net: macsec: update SCI upon MAC address change."
- Revert "xfrm: update SA curlft.use_time", comply with RFC 2367
Previous releases - always broken:
- netfilter: conntrack: work around exceeded TCP receive window
- ipsec: fix a null pointer dereference of dst->dev on a metadata dst
in xfrm_lookup_with_ifid
- moxa: get rid of asymmetry in DMA mapping/unmapping
- dsa: microchip: make learning configurable and keep it off while
standalone
- ice: xsk: prohibit usage of non-balanced queue id
- rxrpc: fix locking in rxrpc's sendmsg
Misc:
- another chunk of sysctl data race silencing"
* tag 'net-6.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (87 commits)
net: lantiq_xrx200: restore buffer if memory allocation failed
net: lantiq_xrx200: fix lock under memory pressure
net: lantiq_xrx200: confirm skb is allocated before using
net: stmmac: work around sporadic tx issue on link-up
ionic: VF initial random MAC address if no assigned mac
ionic: fix up issues with handling EAGAIN on FW cmds
ionic: clear broken state on generation change
rxrpc: Fix locking in rxrpc's sendmsg
net: ethernet: mtk_eth_soc: fix hw hash reporting for MTK_NETSYS_V2
MAINTAINERS: rectify file entry in BONDING DRIVER
i40e: Fix incorrect address type for IPv6 flow rules
ixgbe: stop resetting SYSTIME in ixgbe_ptp_start_cyclecounter
net: Fix a data-race around sysctl_somaxconn.
net: Fix a data-race around netdev_unregister_timeout_secs.
net: Fix a data-race around gro_normal_batch.
net: Fix data-races around sysctl_devconf_inherit_init_net.
net: Fix data-races around sysctl_fb_tunnels_only_for_init_net.
net: Fix a data-race around netdev_budget_usecs.
net: Fix data-races around sysctl_max_skb_frags.
net: Fix a data-race around netdev_budget.
...
Petr Machata says:
====================
mlxsw: Remove some unused code
This patchset removes code that is not used anymore after the following two
commits removed all users:
- commit b0d80c013b ("mlxsw: Remove Mellanox SwitchX-2 ASIC support")
- commit 9b43fbb8ce ("mlxsw: Remove Mellanox SwitchIB ASIC support")
====================
Link: https://lore.kernel.org/r/cover.1661350629.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Function mlxsw_core_port_type_get() is no longer used. So remove it.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
port_type_set devlink op is no longer used by any mlxsw driver,
so remove it.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are some IB leftovers that are no longer used in the code.
So remove them.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jiri Pirko says:
====================
net: devlink: sync flash and dev info commands
Purpose of this patchset is to introduce consistency between two devlink
commands:
devlink dev info
Shows versions of running default flash target and components.
devlink dev flash
Flashes default flash target or component name (if specified
on cmdline).
Currently it is up to the driver what versions to expose and what flash
update component names to accept. This is inconsistent. Thankfully, only
netdevsim currently using components so it is still time
to sanitize this.
This patchset makes sure, that devlink.c calls into driver for
component flash update only in case the driver exposes the same version
name.
Example:
$ devlink dev info
netdevsim/netdevsim10:
driver netdevsim
versions:
running:
fw.mgmt 10.20.30
stored:
fw.mgmt 10.20.30
$ devlink dev flash netdevsim/netdevsim10 file somefile.bin
[fw.mgmt] Preparing to flash
[fw.mgmt] Flashing 100%
[fw.mgmt] Flash select
[fw.mgmt] Flashing done
$ devlink dev flash netdevsim/netdevsim10 file somefile.bin component fw.mgmt
[fw.mgmt] Preparing to flash
[fw.mgmt] Flashing 100%
[fw.mgmt] Flash select
[fw.mgmt] Flashing done
$ devlink dev flash netdevsim/netdevsim10 file somefile.bin component dummy
Error: selected component is not supported by this device.
====================
Link: https://lore.kernel.org/r/20220824122011.1204330-1-jiri@resnulli.us
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Limit the acceptance of component name passed to cmd_flash_update() to
match one of the versions returned by info_get(), marked by version type.
This makes things clearer and enforces 1:1 mapping between exposed
version and accepted flash component.
Check VERSION_TYPE_COMPONENT version type during cmd_flash_update()
execution by calling info_get() with different "req" context.
That causes info_get() to lookup the component name instead of
filling-up the netlink message.
Remove "UPDATE_COMPONENT" flag which becomes used.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix the only component user which is netdevsim. It uses component named
"fw.mgmt" in selftests. So add this version to info_get() output with
version type component.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
