The TCS4525 has 128 voltage steps. With the calculation set to 127 the
most significant bit is disregarded which leads to a miscalculation of
the voltage by about 200mv.
Fix the calculation to end deadlock on the rk3566-quartz64 which uses
this as the cpu regulator.
Fixes: 914df8faa7 ("regulator: fan53555: Add TCS4525 DCDC support")
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Link: https://lore.kernel.org/r/20210511211335.2935163-2-pgwipeout@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The tcs4525 voltage calculation is incorrect, which leads to a deadlock
on the rk3566-quartz64 board when loading cpufreq.
Fix the voltage calculation to correct the deadlock.
While we are at it, add a safety check and clean up the function names
to be more accurate.
Peter Geis (3):
regulator: fan53555: fix TCS4525 voltage calulation
regulator: fan53555: only bind tcs4525 to correct chip id
regulator: fan53555: fix tcs4525 function names
drivers/regulator/fan53555.c | 44 ++++++++++++++++++++++--------------
1 file changed, 27 insertions(+), 17 deletions(-)
--
2.25.1
The TCS4525 has 128 voltage steps. With the calculation set to 127 the
most significant bit is disregarded which leads to a miscalculation of
the voltage by about 200mv.
Fix the calculation to end deadlock on the rk3566-quartz64 which uses
this as the cpu regulator.
Fixes: 914df8faa7 ("regulator: fan53555: Add TCS4525 DCDC support")
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Link: https://lore.kernel.org/r/20210511211335.2935163-2-pgwipeout@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
V3:
- Drop the SoC regulator constraints for
regulator-min-microamp
regulator-max-microamp
These will be applied on a per-board basis - Mark Brown
V2:
The first version of this patch set the current limit to 3 amps as was done
in downstream. Mark indicated a preference to set this on a per-system
basis instead of blitzing it, as in downstream.
Looking at what was upstream versus what was in my working tree I saw that
in fact the VBUS boost driver had been upstreamed minus accompanying DTS in
pm8150b.
So there's no need for a fixes as this driver doesn't appear to be in use.
A subsequent patchset will enable the VBUS boost for the two relevant
upstream platforms.
First thing though, is the driver + dts change.
- Use regulator_set_current_limit_regmap/regulator_get_current_limit_regmap
with a relevant current-to-bitmap lookup.
- Add a parallel DTS entry to the pm8150b
It looks like this was submitted upstream but not followed up on
I've add regulator-min-microamp/regulator-max-microamp to Wesley's
original work.
I've made sure to test that its possible to set the current to anything in
the range of 500 mA to 3 A and confirmed the output on a scope.
Once these two patches are in, I'll send out board enablement for the
sm8150-mtp and qrb5165-rb5.
https://lore.kernel.org/linux-arm-msm/8687acdb-75e9-5fc5-dd3e-9a19615676b5@linaro.org/T/#t
Bryan O'Donoghue (1):
regulator: Add a routine to set the current limit for QCOM PMIC VBUS
Wesley Cheng (1):
arm64: boot: dts: qcom: pm8150b: Add DTS node for PMIC VBUS booster
arch/arm64/boot/dts/qcom/pm8150b.dtsi | 6 ++++++
drivers/regulator/qcom_usb_vbus-regulator.c | 12 ++++++++++++
2 files changed, 18 insertions(+)
--
2.30.1
Add hooks to regulator_get_current_limit_regmap() and
regulator_set_current_limit_regmap() with an accompanying map of amperages.
This lets us use the existing helper functions to map requested current
settings to register bit-map/indicies.
This change is required to elevate the default 2 Amps set by the bootloader
to 3 Amps or indeed to constrain the value lower as the system design may
dictate.
The valid range is 500 mA to 3 A in increments of 500 mA.
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20210427130712.2005456-2-bryan.odonoghue@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit b9d79e4ca4 ("fbmem: Mark proc_fb_seq_ops as __maybe_unused")
places the '__maybe_unused' in an entirely incorrect location between
the "struct" keyword and the structure name.
It's a wonder that gcc accepts that silently, but clang quite reasonably
warns about it:
drivers/video/fbdev/core/fbmem.c:736:21: warning: attribute declaration must precede definition [-Wignored-attributes]
static const struct __maybe_unused seq_operations proc_fb_seq_ops = {
^
Fix it.
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull drm fixes from Dave Airlie:
"Bit later than usual, I queued them all up on Friday then promptly
forgot to write the pull request email. This is mainly amdgpu fixes,
with some radeon/msm/fbdev and one i915 gvt fix thrown in.
amdgpu:
- MPO hang workaround
- Fix for concurrent VM flushes on vega/navi
- dcefclk is not adjustable on navi1x and newer
- MST HPD debugfs fix
- Suspend/resumes fixes
- Register VGA clients late in case driver fails to load
- Fix GEM leak in user framebuffer create
- Add support for polaris12 with 32 bit memory interface
- Fix duplicate cursor issue when using overlay
- Fix corruption with tiled surfaces on VCN3
- Add BO size and stride check to fix BO size verification
radeon:
- Fix off-by-one in power state parsing
- Fix possible memory leak in power state parsing
msm:
- NULL ptr dereference fix
fbdev:
- procfs disabled warning fix
i915:
- gvt: Fix a possible division by zero in vgpu display rate
calculation"
* tag 'drm-next-2021-05-10' of git://anongit.freedesktop.org/drm/drm:
drm/amdgpu: Use device specific BO size & stride check.
drm/amdgpu: Init GFX10_ADDR_CONFIG for VCN v3 in DPG mode.
drm/amd/pm: initialize variable
drm/radeon: Avoid power table parsing memory leaks
drm/radeon: Fix off-by-one power_state index heap overwrite
drm/amd/display: Fix two cursor duplication when using overlay
drm/amdgpu: add new MC firmware for Polaris12 32bit ASIC
fbmem: Mark proc_fb_seq_ops as __maybe_unused
drm/msm/dpu: Delete bonkers code
drm/i915/gvt: Prevent divided by zero when calculating refresh rate
amdgpu: fix GEM obj leak in amdgpu_display_user_framebuffer_create
drm/amdgpu: Register VGA clients after init can no longer fail
drm/amdgpu: Handling of amdgpu_device_resume return value for graceful teardown
drm/amdgpu: fix r initial values
drm/amd/display: fix wrong statement in mst hpd debugfs
amdgpu/pm: set pp_dpm_dcefclk to readonly on NAVI10 and newer gpus
amdgpu/pm: Prevent force of DCEFCLK on NAVI10 and SIENNA_CICHLID
drm/amdgpu: fix concurrent VM flushes on Vega/Navi v2
drm/amd/display: Reject non-zero src_y and src_x for video planes
Pull block fix from Jens Axboe:
"Turns out the bio max size change still has issues, so let's get it
reverted for 5.13-rc1. We'll shake out the issues there and defer it
to 5.14 instead"
* tag 'block-5.13-2021-05-09' of git://git.kernel.dk/linux-block:
Revert "bio: limit bio max size"
Pull cifs fixes from Steve French:
"Three small SMB3 chmultichannel related changesets (also for stable)
from the SMB3 test event this week.
The other fixes are still in review/testing"
* tag '5.13-rc-smb3-part3' of git://git.samba.org/sfrench/cifs-2.6:
smb3: if max_channels set to more than one channel request multichannel
smb3: do not attempt multichannel to server which does not support it
smb3: when mounting with multichannel include it in requested capabilities
Pull scheduler fixes from Thomas Gleixner:
"A set of scheduler updates:
- Prevent PSI state corruption when schedule() races with cgroup
move.
A recent commit combined two PSI callbacks to reduce the number of
cgroup tree updates, but missed that schedule() can drop rq::lock
for load balancing, which opens the race window for
cgroup_move_task() which then observes half updated state.
The fix is to solely use task::ps_flags instead of looking at the
potentially mismatching scheduler state
- Prevent an out-of-bounds access in uclamp caused bu a rounding
division which can lead to an off-by-one error exceeding the
buckets array size.
- Prevent unfairness caused by missing load decay when a task is
attached to a cfs runqueue.
The old load of the task was attached to the runqueue and never
removed. Fix it by enforcing the load update through the hierarchy
for unthrottled run queue instances.
- A documentation fix fot the 'sched_verbose' command line option"
* tag 'sched-urgent-2021-05-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Fix unfairness caused by missing load decay
sched: Fix out-of-bound access in uclamp
psi: Fix psi state corruption when schedule() races with cgroup move
sched,doc: sched_debug_verbose cmdline should be sched_verbose
Pull locking fixes from Thomas Gleixner:
"A set of locking related fixes and updates:
- Two fixes for the futex syscall related to the timeout handling.
FUTEX_LOCK_PI does not support the FUTEX_CLOCK_REALTIME bit and
because it's not set the time namespace adjustment for clock
MONOTONIC is applied wrongly.
FUTEX_WAIT cannot support the FUTEX_CLOCK_REALTIME bit because its
always a relative timeout.
- Cleanups in the futex syscall entry points which became obvious
when the two timeout handling bugs were fixed.
- Cleanup of queued_write_lock_slowpath() as suggested by Linus
- Fixup of the smp_call_function_single_async() prototype"
* tag 'locking-urgent-2021-05-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
futex: Make syscall entry points less convoluted
futex: Get rid of the val2 conditional dance
futex: Do not apply time namespace adjustment on FUTEX_LOCK_PI
Revert 337f13046f ("futex: Allow FUTEX_CLOCK_REALTIME with FUTEX_WAIT op")
locking/qrwlock: Cleanup queued_write_lock_slowpath()
smp: Fix smp_call_function_single_async prototype
Pull x86 perf fix from Borislav Petkov:
"Handle power-gating of AMD IOMMU perf counters properly when they are
used"
* tag 'perf_urgent_for_v5.13_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/events/amd/iommu: Fix invalid Perf result due to IOMMU PMC power-gating
Pull x86 fixes from Borislav Petkov:
"A bunch of things accumulated for x86 in the last two weeks:
- Fix guest vtime accounting so that ticks happening while the guest
is running can also be accounted to it. Along with a consolidation
to the guest-specific context tracking helpers.
- Provide for the host NMI handler running after a VMX VMEXIT to be
able to run on the kernel stack correctly.
- Initialize MSR_TSC_AUX when RDPID is supported and not RDTSCP (virt
relevant - real hw supports both)
- A code generation improvement to TASK_SIZE_MAX through the use of
alternatives
- The usual misc and related cleanups and improvements"
* tag 'x86_urgent_for_v5.13_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
KVM: x86: Consolidate guest enter/exit logic to common helpers
context_tracking: KVM: Move guest enter/exit wrappers to KVM's domain
context_tracking: Consolidate guest enter/exit wrappers
sched/vtime: Move guest enter/exit vtime accounting to vtime.h
sched/vtime: Move vtime accounting external declarations above inlines
KVM: x86: Defer vtime accounting 'til after IRQ handling
context_tracking: Move guest exit vtime accounting to separate helpers
context_tracking: Move guest exit context tracking to separate helpers
KVM/VMX: Invoke NMI non-IST entry instead of IST entry
x86/cpu: Remove write_tsc() and write_rdtscp_aux() wrappers
x86/cpu: Initialize MSR_TSC_AUX if RDTSCP *or* RDPID is supported
x86/resctrl: Fix init const confusion
x86: Delete UD0, UD1 traces
x86/smpboot: Remove duplicate includes
x86/cpu: Use alternative to generate the TASK_SIZE_MAX constant
Pull RISC-V fixes from Palmer Dabbelt:
- A fix to avoid over-allocating the kernel's mapping on !MMU systems,
which could lead to up to 2MiB of lost memory
- The SiFive address extension errata only manifest on rv64, they are
now disabled on rv32 where they are unnecessary
- A pair of late-landing cleanups
* tag 'riscv-for-linus-5.13-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: remove unused handle_exception symbol
riscv: Consistify protect_kernel_linear_mapping_text_rodata() use
riscv: enable SiFive errata CIP-453 and CIP-1200 Kconfig only if CONFIG_64BIT=y
riscv: Only extend kernel reservation if mapped read-only
intel_dp_check_mst_status() uses a 14-byte array to read the DPRX Event
Status Indicator data, but then passes that buffer at offset 10 off as
an argument to drm_dp_channel_eq_ok().
End result: there are only 4 bytes remaining of the buffer, yet
drm_dp_channel_eq_ok() wants a 6-byte buffer. gcc-11 correctly warns
about this case:
drivers/gpu/drm/i915/display/intel_dp.c: In function ‘intel_dp_check_mst_status’:
drivers/gpu/drm/i915/display/intel_dp.c:3491:22: warning: ‘drm_dp_channel_eq_ok’ reading 6 bytes from a region of size 4 [-Wstringop-overread]
3491 | !drm_dp_channel_eq_ok(&esi[10], intel_dp->lane_count)) {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/i915/display/intel_dp.c:3491:22: note: referencing argument 1 of type ‘const u8 *’ {aka ‘const unsigned char *’}
In file included from drivers/gpu/drm/i915/display/intel_dp.c:38:
include/drm/drm_dp_helper.h:1466:6: note: in a call to function ‘drm_dp_channel_eq_ok’
1466 | bool drm_dp_channel_eq_ok(const u8 link_status[DP_LINK_STATUS_SIZE],
| ^~~~~~~~~~~~~~~~~~~~
6:14 elapsed
This commit just extends the original array by 2 zero-initialized bytes,
avoiding the warning.
There may be some underlying bug in here that caused this confusion, but
this is at least no worse than the existing situation that could use
random data off the stack.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull more SCSI updates from James Bottomley:
"This is a set of minor fixes in various drivers (qla2xxx, ufs,
scsi_debug, lpfc) one doc fix and a fairly large update to the fnic
driver to remove the open coded iteration functions in favour of the
scsi provided ones"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: fnic: Use scsi_host_busy_iter() to traverse commands
scsi: fnic: Kill 'exclude_id' argument to fnic_cleanup_io()
scsi: scsi_debug: Fix cmd_per_lun, set to max_queue
scsi: ufs: core: Narrow down fast path in system suspend path
scsi: ufs: core: Cancel rpm_dev_flush_recheck_work during system suspend
scsi: ufs: core: Do not put UFS power into LPM if link is broken
scsi: qla2xxx: Prevent PRLI in target mode
scsi: qla2xxx: Add marginal path handling support
scsi: target: tcmu: Return from tcmu_handle_completions() if cmd_id not found
scsi: ufs: core: Fix a typo in ufs-sysfs.c
scsi: lpfc: Fix bad memory access during VPD DUMP mailbox command
scsi: lpfc: Fix DMA virtual address ptr assignment in bsg
scsi: lpfc: Fix illegal memory access on Abort IOCBs
scsi: blk-mq: Fix build warning when making htmldocs
Pull more Kbuild updates from Masahiro Yamada:
- Convert sh and sparc to use generic shell scripts to generate the
syscall headers
- refactor .gitignore files
- Update kernel/config_data.gz only when the content of the .config
is really changed, which avoids the unneeded re-link of vmlinux
- move "remove stale files" workarounds to scripts/remove-stale-files
- suppress unused-but-set-variable warnings by default for Clang
as well
- fix locale setting LANG=C to LC_ALL=C
- improve 'make distclean'
- always keep intermediate objects from scripts/link-vmlinux.sh
- move IF_ENABLED out of <linux/kconfig.h> to make it self-contained
- misc cleanups
* tag 'kbuild-v5.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (25 commits)
linux/kconfig.h: replace IF_ENABLED() with PTR_IF() in <linux/kernel.h>
kbuild: Don't remove link-vmlinux temporary files on exit/signal
kbuild: remove the unneeded comments for external module builds
kbuild: make distclean remove tag files in sub-directories
kbuild: make distclean work against $(objtree) instead of $(srctree)
kbuild: refactor modname-multi by using suffix-search
kbuild: refactor fdtoverlay rule
kbuild: parameterize the .o part of suffix-search
arch: use cross_compiling to check whether it is a cross build or not
kbuild: remove ARCH=sh64 support from top Makefile
.gitignore: prefix local generated files with a slash
kbuild: replace LANG=C with LC_ALL=C
Makefile: Move -Wno-unused-but-set-variable out of GCC only block
kbuild: add a script to remove stale generated files
kbuild: update config_data.gz only when the content of .config is changed
.gitignore: ignore only top-level modules.builtin
.gitignore: move tags and TAGS close to other tag files
kernel/.gitgnore: remove stale timeconst.h and hz.bc
usr/include: refactor .gitignore
genksyms: fix stale comment
...
