Commit 52e013d0bf ("phy: qcom-qmp: Add support for DP in USB3+DP combo
phy") added support for the DisplayPort part of QMP PHYs but
unfortunately did so by duplicating parts of the shared configuration,
something which has lead to subtle bugs depending on probe order.
As the resources have always been requested based on the USB
configuration, make sure to not rely on fields from the DP configuration
when using them (e.g. in case they get out of sync) and remove the now
unused fields from the DP configurations.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20221114081346.5116-7-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Drop the confused runtime-suspend type check which effectively broke
runtime PM if the DP child node happens to be parsed before the USB
child node during probe (e.g. due to order of child nodes in the
devicetree).
Instead use the new driver data USB PHY pointer to access the USB
configuration and resources.
Fixes: 52e013d0bf ("phy: qcom-qmp: Add support for DP in USB3+DP combo phy")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20221114081346.5116-6-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The PHY is powered on during phy-init by setting the SW_PWRDN bit in the
COM_POWER_DOWN_CTRL register and then setting the same bit in the in the
PCS_POWER_DOWN_CONTROL register that belongs to the USB part of the
PHY.
Currently, whether power on succeeds depends on probe order and having
the USB part of the PHY be initialised first. In case the DP part of the
PHY is instead initialised first, the intended power on of the USB block
results in a corrupted DP_PHY register (e.g. DP_PHY_AUX_CFG8).
Add a pointer to the USB part of the PHY to the driver data and use that
to power on the PHY also if the DP part of the PHY is initialised first.
Fixes: 52e013d0bf ("phy: qcom-qmp: Add support for DP in USB3+DP combo phy")
Cc: stable@vger.kernel.org # 5.10
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20221114081346.5116-5-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The SDM845 has two resets but the DP configuration erroneously described
only one.
In case the DP part of the PHY is initialised before the USB part (e.g.
depending on probe order), then only the first reset would be asserted.
Add a dedicated configuration for SDM845 rather than reuse the
incompatible SC7180 configuration.
Fixes: d88497fb6b ("phy: qualcomm: phy-qcom-qmp: add support for combo USB3+DP phy on SDM845")
Cc: stable@vger.kernel.org # 6.1
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20221114081346.5116-3-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit af6643242d ("phy: qcom-qmp-pcie: split pcs_misc region for ipq6018
pcie gen3") reworked the pcs regs values and removed the 0x400 offset
for each pcs_misc regs.
This change caused the malfunction of ipq8074 downstream since it still
has the legacy pcs table where pcs_misc are not placed on a different
table and instead put together assuming the offset of 0x400 for the
related pcs_misc regs.
Split pcs_misc init cfg from the ipq8074 pcs init table to be handled
correctly to prepare for actual support for gen3 pcie for ipq8074.
Fixes: af6643242d ("phy: qcom-qmp-pcie: split pcs_misc region for ipq6018 pcie gen3")
Reported-by: Robert Marko <robimarko@gmail.com>
Tested-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20221103212125.17156-1-ansuelsmth@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add the missing delay after asserting reset. This is specifically needed
for the reset to have any effect on SC8280XP.
The vendor driver uses a 1 ms delay, but that seems a bit excessive.
Instead use a 200 us delay which appears to be more than enough and also
matches the UFS reset delay added by commit 870b1279c7 ("scsi:
ufs-qcom: Add reset control support for host controller").
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20221105145939.20318-14-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The current QMP PCIe PHY bindings are based on the original MSM8996
binding which provided multiple PHYs per IP block and these in turn were
described by child nodes.
Later QMP PCIe PHY blocks only provide a single PHY and the remnant
child node does not really reflect the hardware.
The original MSM8996 binding also ended up describing the individual
register blocks as belonging to either the wrapper node or the PHY child
nodes.
This is an unnecessary level of detail which has lead to problems when
later IP blocks using different register layouts have been forced to fit
the original mould rather than updating the binding. The bindings are
arguable also incomplete as they only the describe register blocks used
by the current Linux drivers (e.g. does not include the per lane PCS
registers).
In preparation for adding new bindings for SC8280XP which further
bindings can be based on, rename the current schema file after IPQ8074,
which was the first SoC added to the bindings after MSM8996 (which has
already been split out), and add a reference to the SC8280XP bindings.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20221105145939.20318-11-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Since the QMP driver split there will be at most a single child node so
drop the obsolete iteration construct.
While at it, drop the verbose error logging that would have been
printed also on probe deferrals.
Note that there's no need to check if there are additional child nodes
(the kernel is not a devicetree validator), but let's return an error if
there are no child nodes at all for now.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20221105145939.20318-5-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Document the typical order of API calls to used by new drivers and
controllers. Many existing controllers follow this order, but some do
not. This is especially true for controllers designed to work with one
particular PHY driver, which may not need a call to (for example)
phy_init.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20221018175841.1906611-1-sean.anderson@seco.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Each of the CPSW9G ports in J721e support additional modes like QSGMII.
Add a new compatible for J721e to support the additional modes.
In TI's J721e, each of the CPSW9G ethernet interfaces can act as a
QSGMII main or QSGMII-SUB port. The QSGMII main interface is responsible
for performing auto-negotiation between the MAC and the PHY while the rest
of the interfaces are designated as QSGMII-SUB interfaces, indicating that
they will not be taking part in the auto-negotiation process.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20221026074532.109220-4-s-vadapalli@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The number of QSGMII main ports are specific to the device. TI's J7200 for
which the QSGMII main port property is fetched from the device-tree has
only one QSGMII main port. However, devices like TI's J721e support up to
two QSGMII main ports. Thus, the existing methods for fetching and using
the QSGMII main port are not scalable.
Update the existing methods for handling the QSGMII main ports and its
associated requirements to make it scalable for future devices.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20221026074532.109220-3-s-vadapalli@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
TI's J721e SoC supports additional PHY modes like QSGMII and SGMII
that are not supported on earlier SoCs. Add a compatible for it.
Extend ti,qsgmii-main-ports property to support selection of upto
two main ports at once across the two QSGMII interfaces.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20221026074532.109220-2-s-vadapalli@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
