The preferred name suffix for properties with single and multiple GPIOs
is "gpios". Linux GPIO core code supports both. The DTS has mixed
usage, so switch to preferred naming:
omap3-n900.dtb: lp5523@32: 'enable-gpios' does not match any of the regexes: '^led@[0-8]$', '^multi-led@[0-8]$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221127204058.57111-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
"linux,initrd-start" and "linux,initrd-end" can be 32-bit values even on
a 64-bit platform. Ideally, the size should be based on
'#address-cells', but that has never been enforced in the kernel's FDT
boot parsing code (early_init_dt_check_for_initrd()). Bootloader
behavior is known to vary. For example, kexec always writes these as
64-bit. The result of incorrectly reading 32-bit values is most likely
the reserved memory for the original initrd will still be reserved
for the new kernel. The original arm64 equivalent of this code failed to
release the initrd reserved memory in *all* cases.
Use of_read_number() to mirror the early_init_dt_check_for_initrd()
code.
Fixes: b30be4dc73 ("of: Add a common kexec FDT setup function")
Cc: stable@vger.kernel.org
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Link: https://lore.kernel.org/r/20221128202440.1411895-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Fixed string node names should be under 'properties' rather than
'patternProperties'. Additionally, without beginning and end of line
anchors, any prefix or suffix is allowed on the specified node name.
These cases don't appear to want a prefix or suffix, so move them under
'properties'.
In some cases, the diff turns out to look like we're moving some
patterns rather than the fixed string properties.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20221118223708.1721134-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
The reference by path (&{/cpus/cpu@101/thermal-idle}) in the example causes
an error with new version of dtc:
FATAL ERROR: Can't generate fixup for reference to path &{/cpus/cpu@100/thermal-idle}
This is because the examples are built as an overlay and absolute paths
are not valid as references must be by label. The path was also not
resolvable because, by default, examples are placed under 'example-N'
nodes.
As the example contains top-level nodes, the root node must be explicit for
the example to be extracted as-is. This changes the indentation for the
whole example, but the existing indentation is a mess of of random amounts.
Clean this up to be 4 spaces everywhere.
Link: https://lore.kernel.org/r/20221111162729.3381835-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
It's been a while since the last sync and Lee needs commit 73590342fc85
("libfdt: prevent integer overflow in fdt_next_tag").
This adds the following commits from upstream:
55778a03df61 libfdt: tests: add get_next_tag_invalid_prop_len
73590342fc85 libfdt: prevent integer overflow in fdt_next_tag
035fb90d5375 libfdt: add fdt_get_property_by_offset_w helper
98a07006c48d Makefile: fix infinite recursion by dropping non-existent `%.output`
a036cc7b0c10 Makefile: limit make re-execution to avoid infinite spin
c6e92108bcd9 libdtc: remove duplicate judgments
e37c25677dc9 Don't generate erroneous fixups from reference to path
50454658f2b5 libfdt: Don't mask fdt_get_name() returned error
e64a204196c9 manual.txt: Follow README.md and remove Jon
f508c83fe6f0 Update README in MANIFEST.in and setup.py to README.md
c2ccf8a77dd2 Add description of Signed-off-by lines
90b9d9de42ca Split out information for contributors to CONTRIBUTING.md
0ee1d479b23a Remove Jon Loeliger from maintainers list
b33a73c62c1c Convert README to README.md
7ad60734b1c1 Allow static building with meson
fd9b8c96c780 Allow static building with make
fda71da26e7f libfdt: Handle failed get_name() on BEGIN_NODE
c7c7f17a83d5 Fix test script to run also on dash shell
01f23ffe1679 Add missing relref_merge test to meson test list
ed310803ea89 pylibfdt: add FdtRo.get_path()
c001fc01a43e pylibfdt: fix swig build in install
26c54f840d23 tests: add test cases for label-relative path references
ec7986e682cf dtc: introduce label relative path references
651410e54cb9 util: introduce xstrndup helper
4048aed12b81 setup.py: fix out of tree build
ff5afb96d0c0 Handle integer overflow in check_property_phandle_args()
ca7294434309 README: Explain how to add a new API function
c0c2e115f82e Fix a UB when fdt_get_string return null
cd5f69cbc0d4 tests: setprop_inplace: use xstrdup instead of unchecked strdup
a04f69025003 pylibfdt: add Property.as_*int*_array()
83102717d7c4 pylibfdt: add Property.as_stringlist()
d152126bb029 Fix Python crash on getprop deallocation
17739b7ef510 Support 'r' format for printing raw bytes with fdtget
45f3d1a095dd libfdt: overlay: make overlay_get_target() public
c19a4bafa514 libfdt: fix an incorrect integer promotion
1cc41b1c969f pylibfdt: Add packaging metadata
db72398cd437 README: Update pylibfdt install instructions
383e148b70a4 pylibfdt: fix with Python 3.10
23b56cb7e189 pylibfdt: Move setup.py to the top level
69a760747d8d pylibfdt: Split setup.py author name and email
0b106a77dbdc pylibfdt: Use setuptools_scm for the version
c691776ddb26 pylibfdt: Use setuptools instead of distutils
5216f3f1bbb7 libfdt: Add static lib to meson build
4eda2590f481 CI: Cirrus: bump used FreeBSD from 12.1 to 13.0
Link: https://lore.kernel.org/r/20221101181427.1808703-1-robh@kernel.org/
Signed-off-by: Rob Herring <robh@kernel.org>
Broadcom uses U-Boot for a lot of their bcmbca familiy chipsets. U-Boot
stores its configuration in an environment data block.
Such blocks are usually stored on flash as a separated partition at
hardcoded address. Broadcom however decided to:
1. Store env data block inside U-Boot partition
2. Avoid sticking to hardcoded offsets
3. Use custom header with "uEnv" magic and env data length
Example (length 0x4000):
$ hexdump -n 32 -C -s 0x40000 /dev/mtdblock0
00040000 76 6e 45 75 00 40 00 00 34 89 7a 82 49 4d 41 47 |vnEu.@..4.z.IMAG|
00040010 45 3d 4e 41 4e 44 3a 31 4d 2c 31 30 32 34 4d 00 |E=NAND:1M,1024M.|
(0x40000 offset is unit specific and can change)
Starting with the commit 118f3fbe51 ("dt-bindings: mtd: partitions:
support label/name only partition") DT can describe partitions matching
them by a name (without specifying actual address). With that feature
and this binding change it's possible to:
1. Specify DT node for Broadcom's U-Boot env data subpartition
2. Add nodes for specific environment data variables
3. Reference them as NVMEM cells
This binding is unlikely to help Broadcom's U-Boot. U-Boot SPL needs to
find environment data early (before it accesses DTB) and it does that by
looking for an "uEnv" magic. Dirty way.
This binding can however be used by operating systems. It allows
describing cleanly U-Boot, its env data and variables. It tells
operating system about Broadcom-specific env data so it can parse it.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20221018154202.4634-2-zajec5@gmail.com
Signed-off-by: Rob Herring <robh@kernel.org>
U-Boot partition may contain subpartitions. For example Broadcom
includes environment data block in the middle of its U-Boot partition.
This allows describing Broadcom's U-Boot env data and will allow
referencing its NVMEM cell in the future.
Ref: 118f3fbe51 ("dt-bindings: mtd: partitions: support label/name only partition")
Ref: dd638202df ("dt-bindings: mtd: partitions: add additional example for qcom,smem-part")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20221018154202.4634-1-zajec5@gmail.com
Signed-off-by: Rob Herring <robh@kernel.org>
DTB Overlays (.dtbo) can now be built from source files with the
extension (.dtso). This makes it clear what is the content of the files
and differentiates them from base DTB source files.
Rename the pi433-overlay.dts file to pi433-overlay.dtso and update
the information file pi433.txt for the same.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20221024173434.32518-8-afd@ti.com
Signed-off-by: Rob Herring <robh@kernel.org>
Currently DTB Overlays (.dtbo) are build from source files with the same
extension (.dts) as the base DTs (.dtb). This may become confusing and
even lead to wrong results. For example, a composite DTB (created from a
base DTB and a set of overlays) might have the same name as one of the
overlays that create it.
Different files should be generated from differently named sources.
.dtb <-> .dts
.dtbo <-> .dtso
We do not remove the ability to compile DTBO files from .dts files here,
only add a new rule allowing the .dtso file name. The current .dts named
overlays can be renamed with time. After all have been renamed we can
remove the other rule.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Frank Rowand <frowand.list@gmail.com>
Tested-by: Frank Rowand <frowand.list@gmail.com>
Link: https://lore.kernel.org/r/20221024173434.32518-2-afd@ti.com
Signed-off-by: Rob Herring <robh@kernel.org>
In some cases an hardware peripheral can be used for two exclusive usages.
For example, on STM32MP15 we have the same peripheral for I2S and SPI. We
have dedicated driver for each usage and so a dedicated device node in
devicetree.
To avoid to get useless warnings running "make W=1 dtbs", this patch adds
the "-Wunique_unit_address_if_enabled" flag for a make with W=1. In this
case we will detect a duplicate address only if both devices are
enabled in the devicetree, which is a real error case.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Link: https://lore.kernel.org/r/20221021084447.5550-1-alexandre.torgue@foss.st.com
[robh: Refactor options and keep 'unique_unit_address' for W=2]
Signed-off-by: Rob Herring <robh@kernel.org>
For devices connectable by SPI bus (e.g. already using
"spi-max-frequency" property), reference the "spi-peripheral-props.yaml"
schema to allow using all SPI device properties, even these which device
bindings author did not tried yet.
Change "additionalProperties" to "unevaluatedProperties", so the actual
other properties from "spi-peripheral-props.yaml" can be used. This has
additional impact of allowing also other properties from
panel-common.yaml to be used.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221004120907.72767-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
of_overlay_action_name() returns a string literal from a function local
array. Modifying string literals is undefined behavior which usage of
const pointer can avoid. of_overlay_action_name() is currently only
used once in overlay_notify() to print the returned value.
While on it declare the data array const as well.
Reported by Clang:
In file included from arch/x86/kernel/asm-offsets.c:22:
In file included from arch/x86/kernel/../kvm/vmx/vmx.h:5:
In file included from ./include/linux/kvm_host.h:19:
In file included from ./include/linux/msi.h:23:
In file included from ./arch/x86/include/asm/msi.h:5:
In file included from ./arch/x86/include/asm/irqdomain.h:5:
In file included from ./include/linux/irqdomain.h:35:
./include/linux/of.h:1555:3: error: initializing 'char *' with an expression of type 'const char[5]' discards qualifiers [-Werror,-Wincompatible-pointer-types-discards-qualifiers]
"init",
^~~~~~
./include/linux/of.h:1556:3: error: initializing 'char *' with an expression of type 'const char[10]' discards qualifiers [-Werror,-Wincompatible-pointer-types-discards-qualifiers]
"pre-apply",
^~~~~~~~~~~
./include/linux/of.h:1557:3: error: initializing 'char *' with an expression of type 'const char[11]' discards qualifiers [-Werror,-Wincompatible-pointer-types-discards-qualifiers]
"post-apply",
^~~~~~~~~~~~
./include/linux/of.h:1558:3: error: initializing 'char *' with an expression of type 'const char[11]' discards qualifiers [-Werror,-Wincompatible-pointer-types-discards-qualifiers]
"pre-remove",
^~~~~~~~~~~~
./include/linux/of.h:1559:3: error: initializing 'char *' with an expression of type 'const char[12]' discards qualifiers [-Werror,-Wincompatible-pointer-types-discards-qualifiers]
"post-remove",
^~~~~~~~~~~~~
Signed-off-by: Christian Göttsche <cgzones@googlemail.com>
Reviewed-by: Frank Rowand <frowand.list@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20221012174622.45006-1-cgzones@googlemail.com
Signed-off-by: Rob Herring <robh@kernel.org>
Pull more random number generator updates from Jason Donenfeld:
"This time with some large scale treewide cleanups.
The intent of this pull is to clean up the way callers fetch random
integers. The current rules for doing this right are:
- If you want a secure or an insecure random u64, use get_random_u64()
- If you want a secure or an insecure random u32, use get_random_u32()
The old function prandom_u32() has been deprecated for a while
now and is just a wrapper around get_random_u32(). Same for
get_random_int().
- If you want a secure or an insecure random u16, use get_random_u16()
- If you want a secure or an insecure random u8, use get_random_u8()
- If you want secure or insecure random bytes, use get_random_bytes().
The old function prandom_bytes() has been deprecated for a while
now and has long been a wrapper around get_random_bytes()
- If you want a non-uniform random u32, u16, or u8 bounded by a
certain open interval maximum, use prandom_u32_max()
I say "non-uniform", because it doesn't do any rejection sampling
or divisions. Hence, it stays within the prandom_*() namespace, not
the get_random_*() namespace.
I'm currently investigating a "uniform" function for 6.2. We'll see
what comes of that.
By applying these rules uniformly, we get several benefits:
- By using prandom_u32_max() with an upper-bound that the compiler
can prove at compile-time is ≤65536 or ≤256, internally
get_random_u16() or get_random_u8() is used, which wastes fewer
batched random bytes, and hence has higher throughput.
- By using prandom_u32_max() instead of %, when the upper-bound is
not a constant, division is still avoided, because
prandom_u32_max() uses a faster multiplication-based trick instead.
- By using get_random_u16() or get_random_u8() in cases where the
return value is intended to indeed be a u16 or a u8, we waste fewer
batched random bytes, and hence have higher throughput.
This series was originally done by hand while I was on an airplane
without Internet. Later, Kees and I worked on retroactively figuring
out what could be done with Coccinelle and what had to be done
manually, and then we split things up based on that.
So while this touches a lot of files, the actual amount of code that's
hand fiddled is comfortably small"
* tag 'random-6.1-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random:
prandom: remove unused functions
treewide: use get_random_bytes() when possible
treewide: use get_random_u32() when possible
treewide: use get_random_{u8,u16}() when possible, part 2
treewide: use get_random_{u8,u16}() when possible, part 1
treewide: use prandom_u32_max() when possible, part 2
treewide: use prandom_u32_max() when possible, part 1
Pull more perf tools updates from Arnaldo Carvalho de Melo:
- Use BPF CO-RE (Compile Once, Run Everywhere) to support old kernels
when using bperf (perf BPF based counters) with cgroups.
- Support HiSilicon PCIe Performance Monitoring Unit (PMU), that
monitors bandwidth, latency, bus utilization and buffer occupancy.
Documented in Documentation/admin-guide/perf/hisi-pcie-pmu.rst.
- User space tasks can migrate between CPUs, so when tracing selected
CPUs, system-wide sideband is still needed, fix it in the setup of
Intel PT on hybrid systems.
- Fix metricgroups title message in 'perf list', it should state that
the metrics groups are to be used with the '-M' option, not '-e'.
- Sync the msr-index.h copy with the kernel sources, adding support for
using "AMD64_TSC_RATIO" in filter expressions in 'perf trace' as well
as decoding it when printing the MSR tracepoint arguments.
- Fix program header size and alignment when generating a JIT ELF in
'perf inject'.
- Add multiple new Intel PT 'perf test' entries, including a jitdump
one.
- Fix the 'perf test' entries for 'perf stat' CSV and JSON output when
running on PowerPC due to an invalid topology number in that arch.
- Fix the 'perf test' for arm_coresight failures on the ARM Juno
system.
- Fix the 'perf test' attr entry for PERF_FORMAT_LOST, adding this
option to the or expression expected in the intercepted
perf_event_open() syscall.
- Add missing condition flags ('hs', 'lo', 'vc', 'vs') for arm64 in the
'perf annotate' asm parser.
- Fix 'perf mem record -C' option processing, it was being chopped up
when preparing the underlying 'perf record -e mem-events' and thus
being ignored, requiring using '-- -C CPUs' as a workaround.
- Improvements and tidy ups for 'perf test' shell infra.
- Fix Intel PT information printing segfault in uClibc, where a NULL
format was being passed to fprintf.
* tag 'perf-tools-for-v6.1-2-2022-10-16' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (23 commits)
tools arch x86: Sync the msr-index.h copy with the kernel sources
perf auxtrace arm64: Add support for parsing HiSilicon PCIe Trace packet
perf auxtrace arm64: Add support for HiSilicon PCIe Tune and Trace device driver
perf auxtrace arm: Refactor event list iteration in auxtrace_record__init()
perf tests stat+json_output: Include sanity check for topology
perf tests stat+csv_output: Include sanity check for topology
perf intel-pt: Fix system_wide dummy event for hybrid
perf intel-pt: Fix segfault in intel_pt_print_info() with uClibc
perf test: Fix attr tests for PERF_FORMAT_LOST
perf test: test_intel_pt.sh: Add 9 tests
perf inject: Fix GEN_ELF_TEXT_OFFSET for jit
perf test: test_intel_pt.sh: Add jitdump test
perf test: test_intel_pt.sh: Tidy some alignment
perf test: test_intel_pt.sh: Print a message when skipping kernel tracing
perf test: test_intel_pt.sh: Tidy some perf record options
perf test: test_intel_pt.sh: Fix return checking again
perf: Skip and warn on unknown format 'configN' attrs
perf list: Fix metricgroups title message
perf mem: Fix -C option behavior for perf mem record
perf annotate: Add missing condition flags for arm64
...
Pull Kbuild fixes from Masahiro Yamada:
- Fix CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y compile error for the
combination of Clang >= 14 and GAS <= 2.35.
- Drop vmlinux.bz2 from the rpm package as it just annoyingly increased
the package size.
- Fix modpost error under build environments using musl.
- Make *.ll files keep value names for easier debugging
- Fix single directory build
- Prevent RISC-V from selecting the broken DWARF5 support when Clang
and GAS are used together.
* tag 'kbuild-fixes-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
lib/Kconfig.debug: Add check for non-constant .{s,u}leb128 support to DWARF5
kbuild: fix single directory build
kbuild: add -fno-discard-value-names to cmd_cc_ll_c
scripts/clang-tools: Convert clang-tidy args to list
modpost: put modpost options before argument
kbuild: Stop including vmlinux.bz2 in the rpm's
Kconfig.debug: add toolchain checks for DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT
Kconfig.debug: simplify the dependency of DEBUG_INFO_DWARF4/5
Pull more clk updates from Stephen Boyd:
"This is the final part of the clk patches for this merge window.
The clk rate range series needed another week to fully bake. Maxime
fixed the bug that broke clk notifiers and prevented this from being
included in the first pull request. He also added a unit test on top
to make sure it doesn't break so easily again. The majority of the
series fixes up how the clk_set_rate_*() APIs work, particularly
around when the rate constraints are dropped and how they move around
when reparenting clks. Overall it's a much needed improvement to the
clk rate range APIs that used to be pretty broken if you looked
sideways.
Beyond the core changes there are a few driver fixes for a compilation
issue or improper data causing clks to fail to register or have the
wrong parents. These are good to get in before the first -rc so that
the system actually boots on the affected devices"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (31 commits)
clk: tegra: Fix Tegra PWM parent clock
clk: at91: fix the build with binutils 2.27
clk: qcom: gcc-msm8660: Drop hardcoded fixed board clocks
clk: mediatek: clk-mux: Add .determine_rate() callback
clk: tests: Add tests for notifiers
clk: Update req_rate on __clk_recalc_rates()
clk: tests: Add missing test case for ranges
clk: qcom: clk-rcg2: Take clock boundaries into consideration for gfx3d
clk: Introduce the clk_hw_get_rate_range function
clk: Zero the clk_rate_request structure
clk: Stop forwarding clk_rate_requests to the parent
clk: Constify clk_has_parent()
clk: Introduce clk_core_has_parent()
clk: Switch from __clk_determine_rate to clk_core_round_rate_nolock
clk: Add our request boundaries in clk_core_init_rate_req
clk: Introduce clk_hw_init_rate_request()
clk: Move clk_core_init_rate_req() from clk_core_round_rate_nolock() to its caller
clk: Change clk_core_init_rate_req prototype
clk: Set req_rate on reparenting
clk: Take into account uncached clocks in clk_set_rate_range()
...
Pull more cifs updates from Steve French:
- fix a regression in guest mounts to old servers
- improvements to directory leasing (caching directory entries safely
beyond the root directory)
- symlink improvement (reducing roundtrips needed to process symlinks)
- an lseek fix (to problem where some dir entries could be skipped)
- improved ioctl for returning more detailed information on directory
change notifications
- clarify multichannel interface query warning
- cleanup fix (for better aligning buffers using ALIGN and round_up)
- a compounding fix
- fix some uninitialized variable bugs found by Coverity and the kernel
test robot
* tag '6.1-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
smb3: improve SMB3 change notification support
cifs: lease key is uninitialized in two additional functions when smb1
cifs: lease key is uninitialized in smb1 paths
smb3: must initialize two ACL struct fields to zero
cifs: fix double-fault crash during ntlmssp
cifs: fix static checker warning
cifs: use ALIGN() and round_up() macros
cifs: find and use the dentry for cached non-root directories also
cifs: enable caching of directories for which a lease is held
cifs: prevent copying past input buffer boundaries
cifs: fix uninitialised var in smb2_compound_op()
cifs: improve symlink handling for smb2+
smb3: clarify multichannel warning
cifs: fix regression in very old smb1 mounts
cifs: fix skipping to incorrect offset in emit_cached_dirents
When building with a RISC-V kernel with DWARF5 debug info using clang
and the GNU assembler, several instances of the following error appear:
/tmp/vgettimeofday-48aa35.s:2963: Error: non-constant .uleb128 is not supported
Dumping the .s file reveals these .uleb128 directives come from
.debug_loc and .debug_ranges:
.Ldebug_loc0:
.byte 4 # DW_LLE_offset_pair
.uleb128 .Lfunc_begin0-.Lfunc_begin0 # starting offset
.uleb128 .Ltmp1-.Lfunc_begin0 # ending offset
.byte 1 # Loc expr size
.byte 90 # DW_OP_reg10
.byte 0 # DW_LLE_end_of_list
.Ldebug_ranges0:
.byte 4 # DW_RLE_offset_pair
.uleb128 .Ltmp6-.Lfunc_begin0 # starting offset
.uleb128 .Ltmp27-.Lfunc_begin0 # ending offset
.byte 4 # DW_RLE_offset_pair
.uleb128 .Ltmp28-.Lfunc_begin0 # starting offset
.uleb128 .Ltmp30-.Lfunc_begin0 # ending offset
.byte 0 # DW_RLE_end_of_list
There is an outstanding binutils issue to support a non-constant operand
to .sleb128 and .uleb128 in GAS for RISC-V but there does not appear to
be any movement on it, due to concerns over how it would work with
linker relaxation.
To avoid these build errors, prevent DWARF5 from being selected when
using clang and an assembler that does not have support for these symbol
deltas, which can be easily checked in Kconfig with as-instr plus the
small test program from the dwz test suite from the binutils issue.
Link: https://sourceware.org/bugzilla/show_bug.cgi?id=27215
Link: https://github.com/ClangBuiltLinux/linux/issues/1719
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Commit f110e5a250 ("kbuild: refactor single builds of *.ko") was wrong.
KBUILD_MODULES _is_ needed for single builds.
Otherwise, "make foo/bar/baz/" does not build module objects at all.
Fixes: f110e5a250 ("kbuild: refactor single builds of *.ko")
Reported-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Tested-by: David Sterba <dsterba@suse.com>
Pull slab hotfix from Vlastimil Babka:
"A single fix for the common-kmalloc series, for warnings on mips and
sparc64 reported by Guenter Roeck"
* tag 'slab-for-6.1-rc1-hotfix' of git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab:
mm/slab: use kmalloc_node() for off slab freelist_idx_t array allocation
Pull OpenRISC updates from Stafford Horne:
"I have relocated to London so not much work from me while I get
settled.
Still, OpenRISC picked up two patches in this window:
- Fix for kernel page table walking from Jann Horn
- MAINTAINER entry cleanup from Palmer Dabbelt"
* tag 'for-linus' of https://github.com/openrisc/linux:
MAINTAINERS: git://github -> https://github.com for openrisc
openrisc: Fix pagewalk usage in arch_dma_{clear, set}_uncached
Pull pci fix from Bjorn Helgaas:
"Revert the attempt to distribute spare resources to unconfigured
hotplug bridges at boot time.
This fixed some dock hot-add scenarios, but Jonathan Cameron reported
that it broke a topology with a multi-function device where one
function was a Switch Upstream Port and the other was an Endpoint"
* tag 'pci-v6.1-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "PCI: Distribute available resources for root buses, too"
After commit d6a71648db ("mm/slab: kmalloc: pass requests larger than
order-1 page to page allocator"), SLAB passes large ( > PAGE_SIZE * 2)
requests to buddy like SLUB does.
SLAB has been using kmalloc caches to allocate freelist_idx_t array for
off slab caches. But after the commit, freelist_size can be bigger than
KMALLOC_MAX_CACHE_SIZE.
Instead of using pointer to kmalloc cache, use kmalloc_node() and only
check if the kmalloc cache is off slab during calculate_slab_order().
If freelist_size > KMALLOC_MAX_CACHE_SIZE, no looping condition happens
as it allocates freelist_idx_t array directly from buddy.
Link: https://lore.kernel.org/all/20221014205818.GA1428667@roeck-us.net/
Reported-and-tested-by: Guenter Roeck <linux@roeck-us.net>
Fixes: d6a71648db ("mm/slab: kmalloc: pass requests larger than order-1 page to page allocator")
Signed-off-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
