The current code does not have the MU EDCA feature, so it cannot support
the use of EDCA by STA in specific UL MU HE TB PPDU transmissions. Refer
to IEEE Std 802.11ax-2021 "9.4.2.251 MU EDCA Parameter Set element",
"26.2.7 EDCA operation using MU EDCA parameters".
Add ath11k_mac_op_conf_tx_mu_edca() to construct the MU EDCA parameters
received from mac80211 into WMI WMM parameters，and send to the firmware
according to the different WMM type flags.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-04523-QCAHSPSWPL_V1_V2_SILICONZ_IOE-1
Signed-off-by: Yu Zhang (Yuriy) <quic_yuzha@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250124061343.2263467-1-quic_yuzha@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, ath12k does not support reading variant from ACPI board data
filename extension for downloading board data file.
To address this issue, obtain the string of the ACPI data filename
extension and use it as part of the string to search for the board data
file from board-2.bin.
This patch will not affect QCN9274, because only WCN7850 supports ACPI.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20250113074810.29729-5-quic_lingbok@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the timing for accessing the ACPI table is inappropriate.
Due to special ACPI requirements, the ACPI table must be obtained before
downloading the board data file. Therefore, adjust the timing for accessing
the ACPI table accordingly.
This patch will not affect QCN9274, because only WCN7850 supports ACPI.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20250113074810.29729-4-quic_lingbok@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, ath12k does not support enable or disable specific features by
ACPI bitflag.
To address this issue, obtain the ACPI bitflag value and use it to
selectively enable or disable specific features.
This patch will not affect QCN9274, because only WCN7850 supports ACPI.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20250113074810.29729-3-quic_lingbok@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently ath12k_mac_ieee80211_sta_bw_to_wmi() handles the bandwidth from
sta's deflink member. This works only for non-ML station. Now that MLO
support is there, extend this function to use link sta instead of deflink.
Additionally, in ath12k_mac_handle_link_sta_state(), the link sta structure
is not accessible, making it difficult to fetch the bandwidth there.
However, ath12k_mac_station_assoc() does reference the link sta structure.
Therefore, move the initial assignment of the arsta bandwidth member to
ath12k_mac_station_assoc().
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Acked-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Link: https://patch.msgid.link/20250110-fix_link_sta_bandwidth_update-v1-2-61b6f3ef2ea3@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In case of MHI error a reset work will be queued which will try
napi_disable() after napi_synchronize().
As the napi will be only enabled after qmi_firmware_ready event,
trying napi_synchronize() before napi_enable() will result in
indefinite sleep in case of a firmware crash in QMI init sequence.
To avoid this, introduce napi_enabled flag to check if napi is enabled
or not before calling napi_synchronize().
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Avula Sri Charan <quic_asrichar@quicinc.com>
Signed-off-by: Tamizh Chelvam Raja <quic_tamizhr@quicinc.com>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250124090058.3194299-1-quic_tamizhr@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, when the driver receives a channel switch count WMI event from
the firmware with a count greater than 1, it calls
ieee80211_beacon_update_cntdwn(). If the beacon transmission fails, the
event will be received again with the previous count value. In this
scenario, the host decrements the mac80211 counter again, causing it to
move ahead of the firmware counter. Ultimately, when the firmware count
reaches 1, the mac80211 counter will reach zero, triggering a
WARN_ON_ONCE(). Therefore, there is a need to check the count value in the
event.
Hence to fix this, maintain the current ongoing counter in arvif. If the
count in the event does not match the expected value, silently discard the
event.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20250124-ath12k_mlo_csa-v2-4-420c42fcfecf@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
At present, the driver configures the firmware to send the Channel Switch
(CS) count event only when the count reaches zero during a Channel Switch
Announcement (CSA). For frames managed by the upper layer, where the driver
does not update the counter, the CS count in these frames remains unchanged
throughout the entire CSA period. This is because the upper layer is not
aware of the latest ongoing count. Indicating same count value throughout
the CSA time is wrong and could lead to connection instabilities.
Fix this by configuring firmware to send CS count event for every count and
then accordingly decrementing the count in mac80211.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20250124-ath12k_mlo_csa-v2-3-420c42fcfecf@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The driver is informed of the counter offsets in the beacon during CSA
through the ieee80211_mutable_offsets structure. According to the
documentation for the cntdwn_counter_offs member, "This array can contain
zero values which should be ignored." However, the current implementation
uses these values unconditionally, without checking for zeros.
Whenever CSA is active, these offsets are guaranteed to be set. Therefore,
add a check for CSA active status before setting the CSA switch count
offsets. This ensures that the offsets are only set when CSA is active,
preventing incorrect configurations.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20250124-ath12k_mlo_csa-v2-2-420c42fcfecf@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The current code has ath12k_wmi_bcn_tmpl() accepting separate ar and
vdev_id parameters. However, ath12k_link_vif structure can be used to
derive both of these.
Hence, simplify the function signature.
Later change needs arvif pointer access within the function hence it is
better if arvif is directly passed now.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20250124-ath12k_mlo_csa-v2-1-420c42fcfecf@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently in ath12k_mac_op_sta_statistics() there is the following
logic:
if (!arsta->txrate.legacy && !arsta->txrate.nss)
return;
Because ath12k_sta_statistics is used to report many info to iw wlan0 link,
if it return for empty legacy and nss of arsta->txrate, then the other
stats after it will not be set.
To address this issue remove the return and instead invert the logic to set
the txrate logic if (arsta->txrate.legacy || arsta->txrate.nss).
The same was done also in both ath10k with commit 1cd6ba8ae3 ("ath10k:
remove return for NL80211_STA_INFO_TX_BITRATE") and ath11k as well with
commit 1d795645e1 ("ath11k: remove return for empty tx bitrate in
mac_op_sta_statistics").
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/38c2a7c4f7eaf57b9306bb95a9e6c42b7d987e05.1738169458.git.repk@triplefau.lt
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In 'ath_cmn_process_fft()', it doesn't make too much sense to
add zero bytes in attempt to improve randomness. So swap calls
to 'memset()' and 'add_device_randomness()' to feed the pool
with actual FFT results rather than zeroes. Compile tested only.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Fixes: 2aa56cca35 ("ath9k: Mix the received FFT bins to the random pool")
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20250123141058.1696502-1-dmantipov@yandex.ru
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When using nvmem, ath9k could potentially be loaded before nvmem, which
loads after mtd. This is an issue if DT contains an nvmem mac address.
If nvmem is not ready in time for ath9k, -EPROBE_DEFER is returned. Pass
it to _probe so that ath9k can properly grab a potentially present MAC
address.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20241105222326.194417-1-rosenp@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
During monitor destination ring back-pressure, hardware failed to send
HAL_RX_PPDU_END_STATUS_DONE TLV. But driver uses this TLV as a delimiter
to complete one PPDU worth of data parsing. This causes driver to overwrite
the existing PPDU information with the new PPDU information.
Fix it by recording the end reason which is provided under each buffer's
descriptor in skb->cb and uses it while parsing TLV tags to mark the PPDU
end delimiter.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Link: https://patch.msgid.link/20241223060132.3506372-14-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Driver uses monitor destination rings for extended statistics mode and
standalone monitor mode. In extended statistics mode, TLVs are parsed from
the buffer received from the monitor destination ring and assigned to the
ppdu_info structure to update per-packet statistics. In standalone monitor
mode, along with per-packet statistics, the packet data (payload) is
captured, and the driver updates per MSDU to mac80211.
When the AP interface is enabled, only extended statistics mode is
activated. As part of enabling monitor rings for collecting statistics,
the driver subscribes to HAL_RX_MPDU_START TLV in the filter
configuration. This TLV is received from the monitor destination ring, and
kzalloc for the mon_mpdu object occurs, which is not freed, leading to a
memory leak. The kzalloc for the mon_mpdu object is only required while
enabling the standalone monitor interface. This causes a memory leak while
enabling extended statistics mode in the driver.
Fix this memory leak by removing the kzalloc for the mon_mpdu object in
the HAL_RX_MPDU_START TLV handling. Additionally, remove the standalone
monitor mode handlings in the HAL_MON_BUF_ADDR and HAL_RX_MSDU_END TLVs.
These TLV tags will be handled properly when enabling standalone monitor
mode in the future.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Link: https://patch.msgid.link/20241223060132.3506372-13-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Each PPDU contains numerous TLV tags. HAL_RX_PPDU_START marks the start
of the PPDU, and HAL_RX_PPDU_END_STATUS_DONE marks the end. From the
monitor destination rings, the driver retrieves skb containing these
TLV tags and their corresponding data. Sometimes, one PPDU’s information
spreads across multiple skbs. The current parsing logic uses memset on
struct hal_rx_mon_ppdu_info after parsing each skb, leading to information
loss if a PPDU spans multiple skbs. Fix this by setting the
ppdu_continuation flag when the driver fails to get
HAL_RX_PPDU_END_STATUS_DONE, and do memset on struct
hal_rx_mon_ppdu_info only when the ppdu_continuation flag is not set.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Link: https://patch.msgid.link/20241223060132.3506372-12-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In the current implementation, when PPDU spans multiple ring descriptors,
leading to inefficient use of the NAPI budget. The budget counter is
decremented for each ring descriptor, causing rapid depletion of the
budget even though the processing of a single PPDU might not be complete.
To address this issue, modify the code to decrement the budget counter
only when the driver receives HAL_MON_END_OF_PPDU as the end reason. This
change ensures that the budget is decremented only once per PPDU,
resulting in more efficient utilization of the NAPI budget and better
handling of monitor destination ring.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Link: https://patch.msgid.link/20241223060132.3506372-11-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the monitor destination ring's descriptor includes a 2-bit
field for the end reason. Out of all the end reason values, hardware uses
HAL_MON_FLUSH_DETECTED and HAL_MON_PPDU_TRUNCATED to indicate buffers that
should not be processed due to system level errors. Driver should not
process entries with these end reasons, as they contain junk values.
However, the current code lacks end reason-specific checks for the monitor
destination ring, leading to the processing of invalid buffers.
Fix this by adding checks for these two end reasons during the reaping
phase. Free the skb if either HAL_MON_FLUSH_DETECTED or
HAL_MON_PPDU_TRUNCATED is detected, preventing the driver from processing
invalid entries.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Link: https://patch.msgid.link/20241223060132.3506372-10-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When monitor block in Hardware experiences internal backpressure, a ring
entry with the EMPTY_DESC reason is received in the monitor destination
ring descriptor. The cookie field for this corresponding entry is invalid.
Currently driver attempts to process this cookie resulting in invalid
buf_id warning logs flooding the console. To fix this, skip processing the
destination descriptor when the EMPTY_DESCRIPTOR bit is set to true in ring
descriptor, thereby avoiding the processing of junk cookies.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Link: https://patch.msgid.link/20241223060132.3506372-9-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
End offset for the monitor destination ring descriptor is defined as
16 bits, while the firmware definition specifies only 12 bits.
The remaining bits (bit 12 to bit 15) are reserved and may contain
junk values, leading to invalid information retrieval. Fix this issue
by updating the correct genmask values.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Link: https://patch.msgid.link/20241223060132.3506372-8-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, ath12k_dp_mon_srng_process uses ath12k_hal_srng_src_get_next_entry
to fetch the next entry from the destination ring. This is incorrect because
ath12k_hal_srng_src_get_next_entry is intended for source rings, not destination
rings. This leads to invalid entry fetches, causing potential data corruption or
crashes due to accessing incorrect memory locations. This happens because the
source ring and destination ring have different handling mechanisms and using
the wrong function results in incorrect pointer arithmetic and ring management.
To fix this issue, replace the call to ath12k_hal_srng_src_get_next_entry with
ath12k_hal_srng_dst_get_next_entry in ath12k_dp_mon_srng_process. This ensures
that the correct function is used for fetching entries from the destination
ring, preventing invalid memory accesses.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Link: https://patch.msgid.link/20241223060132.3506372-7-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, monitor ring reaping and processing occur in the same loop,
which requires holding ring locks until skb processing is complete.
However, only the ring reaping part requires the ring lock; the skb
processing part does not need it. This approach is problematic because it
unnecessarily extends the duration for which the ring locks are held,
leading to increased contention and potential backpressure issues.
Fix it by holding ring locks only during the reaping phase, as skb
processing does not require them. First, reap the monitor destination ring
with the ring lock and queue the skbs into an skb list. Then, process the
skbs in this list in a separate loop without holding the ring lock.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Link: https://patch.msgid.link/20241223060132.3506372-6-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The current implementation processes the monitor destination ring using
two separate functions, ath12k_dp_mon_srng_process() for standalone
monitor mode and ath12k_dp_mon_rx_process_stats() for statistics.
However, both functions contain same code which performs monitor ring
reaping and skb data processing. To eliminate redundancy, remove the
duplicate code and use a single function to handle both the cases.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Link: https://patch.msgid.link/20241223060132.3506372-5-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
ath12k_mac_op_configure_filter() gets called multiple times during
interface bringup. Applying filter configuration from this function leads
to writing same filter configurations multiple times.
Resolve this issue by relocating the filter configuration to
ath12k_mac_config_mon_status_default(), which is invoked by both
ath12k_mac_op_start() and ath12k_mac_op_stop(). Additionally, set the
rxmon_disable flag to true when called from ath12k_mac_op_stop() to
disable the monitor destination ring.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Link: https://patch.msgid.link/20241223060132.3506372-4-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add provision to configure monitor filter for the destination
ring. These filters are used for requesting statistics or monitor mode
through the monitor destination ring.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Link: https://patch.msgid.link/20241223060132.3506372-3-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add source buffer ring and destination buffer ring ID for monitor rings.
These IDs are used for ring configuration during initial ring setup.
Since monitor rings are enabled based on the rxdma1_enable flag, enable it
in the hardware param for the QCN9274 version 2 hardware and increase the
destination ring size to handle MSDU data buffers.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Link: https://patch.msgid.link/20241223060132.3506372-2-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently in ath12k_dp_rx_process_wbm_err(), when processing packets
received on the WBM error ring, pdev validation is done based upon the
hw_link_id. But hw_link_id corresponds to link id of a given partner pdev
in a MLO hardware group, and is not the correct index to use to lookup a
pdev in an SoC(ab). As a result, pdev validation fails, and the reaped
packets are dropped instead of being processed.
The correct index to use is the pdev_id, which is already derived in the
function. So update the logic to validate the pdev based upon the pdev_id
instead of the hw_link_id. This matches the logic used in other Rx ring
processing functions.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: 1a73acb5fb ("wifi: ath12k: move to HW link id based receive handling")
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Link: https://patch.msgid.link/20250102043048.2596791-1-quic_ramess@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Kmemleak reported this error:
unreferenced object 0xffff1c165cec3060 (size 32):
comm "insmod", pid 560, jiffies 4296964570 (age 235.596s)
backtrace:
[<000000005434db68>] __kmem_cache_alloc_node+0x1f4/0x2c0
[<000000001203b155>] kmalloc_trace+0x40/0x88
[<0000000028adc9c8>] _request_firmware+0xb8/0x608
[<00000000cad1aef7>] firmware_request_nowarn+0x50/0x80
[<000000005011a682>] local_pci_probe+0x48/0xd0
[<00000000077cd295>] pci_device_probe+0xb4/0x200
[<0000000087184c94>] really_probe+0x150/0x2c0
The firmware memory was allocated in ath12k_pci_probe(), but not
freed in ath12k_pci_remove() in case ATH12K_FLAG_QMI_FAIL bit is
set. So call ath12k_fw_unmap() to free the memory.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.2.0-02280-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Signed-off-by: Miaoqing Pan <quic_miaoqing@quicinc.com>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250123080226.1116479-1-quic_miaoqing@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, when sending the scan channel list command to the firmware, the
maximum Tx power is not encoded in the reg2 member. This omission causes
the firmware to be unaware of the host's maximum Tx power, leading to
incorrect Tx power derivation at firmware level.
To resolve this issue, encode the maximum Tx power in the scan channel list
command before sending it to firmware.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Sathishkumar Muruganandam <quic_murugana@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Tested-by: Nicolas Escande <nico.escande@gmail.com>
Link: https://patch.msgid.link/20250107-add_max_reg_pwr_in_scan_ch_list_cmd-v1-1-70d9963a21e4@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the signal strength of "iw dev xxx station dump" always show an
invalid value.
This is because signal strength is only set in ath12k_mgmt_rx_event()
function, and not set for received data packet. So, change to get signal
from firmware and report to mac80211.
After that, "iw dev xxx station dump" show the correct signal strength.
Such as:
Station 00:03:7f:12:03:03 (on wlo1)
inactive time: 36 ms
rx bytes: 61571
rx packets: 336
tx bytes: 28204
tx packets: 205
tx retries: 49
tx failed: 0
beacon loss: 0
beacon rx: 83
rx drop misc: 66
signal: -24 dBm
beacon signal avg: -22 dBm
For WCN7850, the firmware supports db2dbm, so not need to add noise floor.
For QCN9274, the firmware not support db2dbm, so need to add noise floor.
This patch affects the station mode of WCN7850 and QCN9274.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00214-QCAHKSWPL_SILICONZ-1
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Link: https://patch.msgid.link/20250115063537.35797-4-quic_lingbok@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the receive rate of EHT of "iw dev xxx station dump" command
always show an invalid value.
This is because ath12k does not pass information about the rx_status of EHT
to mac80211. So, mac80211 not calculate the receive rate.
To address this issue, add logic for handling rx_status of EHT to the
ath12k_dp_rx_h_rate() function.
After that, "iw dev xxx station dump" show the correct receive rate.
Such as:
Station 00:03:7f:12:03:03 (on wlo1)
inactive time: 48 ms
rx bytes: 59226
rx packets: 320
tx bytes: 26556
tx packets: 191
tx retries: 99
tx failed: 0
beacon loss: 0
beacon rx: 79
rx drop misc: 68
signal: -95 dBm
beacon signal avg: -20 dBm
tx bitrate: 688.2 MBit/s 40MHz EHT-MCS 13 EHT-NSS 2 EHT-GI 0
tx duration: 0 us
rx bitrate: 619.5 MBit/s 40MHz EHT-MCS 8 EHT-NSS 3 EHT-GI 0
This patch affects the station mode of WCN7850 and QCN9274.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00214-QCAHKSWPL_SILICONZ-1
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219715
Link: https://patch.msgid.link/20250115063537.35797-3-quic_lingbok@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the transmit rate of "iw dev xxx station dump" command
always show an invalid value.
To address this issue, ath12k parse the info of transmit complete
report from firmware and indicate the transmit rate to mac80211.
This patch affects the station mode of WCN7850 and QCN9274.
After that, "iw dev xxx station dump" show the correct transmit rate.
Such as:
Station 00:03:7f:12:03:03 (on wlo1)
inactive time: 872 ms
rx bytes: 219111
rx packets: 1133
tx bytes: 53767
tx packets: 462
tx retries: 51
tx failed: 0
beacon loss: 0
beacon rx: 403
rx drop misc: 74
signal: -95 dBm
beacon signal avg: -18 dBm
tx bitrate: 1441.1 MBit/s 80MHz EHT-MCS 13 EHT-NSS 2 EHT-GI 0
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00214-QCAHKSWPL_SILICONZ-1
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219715
Link: https://patch.msgid.link/20250115063537.35797-2-quic_lingbok@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add support to process factory test mode commands(FTM) for calibration.
By default firmware start with MISSION mode and to process the FTM commands
firmware needs to be restarted in FTM mode using module parameter ftm_mode.
The pre-request is all the radios should be down before starting the test.
All ath12k test mode interface related commands specified in enum
ath_tm_cmd.
When start command ATH_TM_CMD_TESTMODE_START is received, ar state
is set to test Mode and FTM daemon sends test mode command to wifi
driver via cfg80211. Wifi driver sends these command to firmware as
wmi events. If it is segmented commands it will be broken down into
multiple segments and encoded with TLV header else it is sent to
firmware as it is.
Firmware response via UTF events, wifi driver creates skb and send
to cfg80211, cfg80211 sends firmware response to FTM daemon via
netlink message.
Command to boot in ftm mode
insmod ath12k ftm_mode=1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Reviewed-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20250119083657.1937557-4-quic_aarasahu@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
User space application requires that the testmode interface
is exactly same between ath drivers. Move testmode_i.h file
in ath directory to ensure that all ath driver uses same testmode
interface instead of duplicating testmode_i.h for each ath drivers.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Reviewed-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20250119083657.1937557-2-quic_aarasahu@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the driver allocates cacheable DMA buffers for the rx_tid
structure using kzalloc() and dma_map_single(). These buffers are
long-lived and can persist for the lifetime of the peer, which is not
advisable. Instead of using kzalloc() and dma_map_single() for allocating
cacheable DMA buffers, utilize the dma_alloc_noncoherent() helper for the
allocation of long-lived cacheable DMA buffers, such as the peer's rx_tid.
Since dma_alloc_noncoherent() returns unaligned physical and virtual
addresses, align them internally before use within the driver. This
ensures proper allocation of non-coherent memory through the kernel
helper.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Link: https://patch.msgid.link/20250119164219.647059-3-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the driver allocates cacheable DMA buffers for rings like
HAL_REO_DST and HAL_WBM2SW_RELEASE. The buffers for HAL_WBM2SW_RELEASE
are large (1024 KiB), exceeding the SWIOTLB slot size of 256 KiB. This
leads to "swiotlb buffer is full" error messages on systems without an
IOMMU that use SWIOTLB, causing driver initialization failures. The driver
calls dma_map_single() with these large buffers obtained from kzalloc(),
resulting in ring initialization errors on systems without an IOMMU that
use SWIOTLB.
To address these issues, replace the flawed buffer allocation mechanism
with the appropriate DMA API. Specifically, use dma_alloc_noncoherent()
for cacheable DMA buffers, ensuring proper freeing of buffers with
dma_free_noncoherent().
Error log:
[ 10.194343] ath11k_pci 0000:04:00.0: swiotlb buffer is full (sz:1048583 bytes), total 32768 (slots), used 2529 (slots)
[ 10.194406] ath11k_pci 0000:04:00.0: failed to set up tcl_comp ring (0) :-12
[ 10.194781] ath11k_pci 0000:04:00.0: failed to init DP: -12
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Reported-by: Tim Harvey <tharvey@gateworks.com>
Closes: https://lore.kernel.org/all/20241210041133.GA17116@lst.de/
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Link: https://patch.msgid.link/20250119164219.647059-2-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, ath12k_dp_mon_rx_parse_status_tlv() takes the TLV tag, TLV data
and TLV userid as separate arguments from the caller. In the future, the
TLV length will be needed for parsing the EHT TLV tag. Therefore, instead
of increasing the number of arguments, pass the TLV header and retrieve the
necessary fields from the TLV header itself.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241224143613.164921-4-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
