[why]
In current implemenation ODM mode is only reset when the last plane is
removed from dc state. For any dc validate we will always remove all
current planes and add new planes. However when switching from no planes
to 1 plane, ODM mode is not reset because no planes get removed. This
has caused an issue where we kept ODM combine when it should have been
remove when a plane is added. The change is to reset ODM mode when
adding the first plane.
Cc: stable@vger.kernel.org
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If there are more than one device doing reset in parallel, the first
device will call kfd_suspend_all_processes() to evict all processes
on all devices, this call takes time to finish. other device will
start reset and recover without waiting. if the process has not been
evicted before doing recover, it will be restored, then caused page
fault.
Signed-off-by: Zhigang Luo <Zhigang.Luo@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
set_q_mode_offs don't get cleared after GPU reset, nexting SET_Q_MODE
packet to init shadow memory will be skiped, hence there has a page fault.
[How]
VM flush is needed after GPU reset, clear set_q_mode_offs when
emitting VM flush.
Fixes: 8bc75586ea ("drm/amdgpu: workaround to avoid SET_Q_MODE packets v2")
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: ZhenGuo Yin <zhenguo.yin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
From MES version 0x54, the log entry increased and require the log buffer
size to be increased. The 16k is maximum size agreed
Signed-off-by: shaoyunl <shaoyun.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The MES log might slow down the performance for extra step of log the data,
disable it by default and introduce a parameter can enable it when necessary
Signed-off-by: shaoyunl <shaoyun.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
While doing multiple S4 stress tests, GC/RLC/PMFW get into
an invalid state resulting into hard hangs.
Adding a GFX reset as workaround just before sending the
MP1_UNLOAD message avoids this failure.
Signed-off-by: Tim Huang <Tim.Huang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently, with F32 HWS GPU reset is only when unmap queue fails.
However, if compute queue doesn't repond to preemption request in time
unmap will return without any error. In this case, only preemption error
is logged and Reset is not triggered. Call GPU reset in this case also.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Reviewed-by: Mukul Joshi <mukul.joshi@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This reverts:
nouveau/gsp: don't check devinit disable on GSP.
and applies a further fix.
It turns out the open gpu driver, checks this register,
but only for display.
Match that behaviour and in the turing path only disable
the display block. (ampere already only does displays).
Fixes: 5d4e8ae6e5 ("nouveau/gsp: don't check devinit disable on GSP.")
Reviewed-by: Danilo Krummrich <dakr@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240408064243.2219527-1-airlied@gmail.com
The previous fix for the circlular lock splat about the busyness
worker wasn't quite complete. Even though the reset-in-progress flag
is cleared at the start of intel_uc_reset_finish, the entire function
is still inside the reset mutex lock. Not sure why the patch appeared
to fix the issue both locally and in CI. However, it is now back
again.
There is a further complication that the wedge code path within
intel_gt_reset() jumps around so much that it results in nested
reset_prepare/_finish calls. That is, the call sequence is:
intel_gt_reset
| reset_prepare
| __intel_gt_set_wedged
| | reset_prepare
| | reset_finish
| reset_finish
The nested finish means that even if the clear of the in-progress flag
was moved to the end of _finish, it would still be clear for the
entire second call. Surprisingly, this does not seem to be causing any
other problems at present.
As an aside, a wedge on fini does not call the finish functions at
all. The reset_in_progress flag is left set (twice).
So instead of trying to cancel the worker anywhere at all in the reset
path, just add a cancel to intel_guc_submission_fini instead. Note
that it is not a problem if the worker is still active during a reset.
Either it will run before the reset path starts locking things and
will simply block the reset code for a tiny amount of time. Or it will
run after the locks have been acquired and will early exit due to the
try-lock.
Also, do not use the reset-in-progress flag to decide whether a
synchronous cancel is safe (from a lockdep perspective) or not.
Instead, use the actual reset mutex state (both the genuine one and
the custom rolled BACKOFF one).
Fixes: 0e00a8814e ("drm/i915/guc: Avoid circular locking issue on busyness flush")
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Cc: Zhanjun Dong <zhanjun.dong@intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Andi Shyti <andi.shyti@linux.intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Nirmoy Das <nirmoy.das@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jonathan Cavitt <jonathan.cavitt@intel.com>
Cc: Prathap Kumar Valsan <prathap.kumar.valsan@intel.com>
Cc: Alan Previn <alan.previn.teres.alexis@intel.com>
Cc: Madhumitha Tolakanahalli Pradeep <madhumitha.tolakanahalli.pradeep@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Ashutosh Dixit <ashutosh.dixit@intel.com>
Cc: Dnyaneshwar Bhadane <dnyaneshwar.bhadane@intel.com>
Reviewed-by: Nirmoy Das <nirmoy.das@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240329235306.1559639-1-John.C.Harrison@Intel.com
(cherry picked from commit 3563d85531)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Currently we only consider the relationship of the
old and new CDCLK frequencies when determining whether
to do the repgramming from intel_set_cdclk_pre_plane_update()
or intel_set_cdclk_post_plane_update().
It is technically possible to have a situation where the
CDCLK frequency is decreasing, but the voltage_level is
increasing due a DDI port. In this case we should bump
the voltage level already in intel_set_cdclk_pre_plane_update()
(so that the voltage_level will have been increased by the
time the port gets enabled), while leaving the CDCLK frequency
unchanged (as active planes/etc. may still depend on it).
We can then reduce the CDCLK frequency to its final value
from intel_set_cdclk_post_plane_update().
In order to handle that correctly we shall construct a
suitable amalgam of the old and new cdclk states in
intel_set_cdclk_pre_plane_update().
And we can simply call intel_set_cdclk() unconditionally
in both places as it will not do anything if nothing actually
changes vs. the current hw state.
v2: Handle cdclk_state->disable_pipes
v3: Only synchronize the cd2x update against the pipe's vblank
when the cdclk frequency is changing during the current
commit phase (Gustavo)
Cc: stable@vger.kernel.org
Cc: Gustavo Sousa <gustavo.sousa@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240402155016.13733-3-ville.syrjala@linux.intel.com
(cherry picked from commit 34d127e2bd)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Currently we always reprogram CDCLK from the
intel_set_cdclk_pre_plane_update() when using squash/crawl.
The code only works correctly for the cd2x update or full
modeset cases, and it was simply never updated to deal with
squash/crawl.
If the CDCLK frequency is increasing we must reprogram it
before we do anything else that might depend on the new
higher frequency, and conversely we must not decrease
the frequency until everything that might still depend
on the old higher frequency has been dealt with.
Since cdclk_state->pipe is only relevant when doing a cd2x
update we can't use it to determine the correct sequence
during squash/crawl. To that end introduce cdclk_state->disable_pipes
which simply indicates that we must perform the update
while the pipes are disable (ie. during
intel_set_cdclk_pre_plane_update()). Otherwise we use the
same old vs. new CDCLK frequency comparsiong as for cd2x
updates.
The only remaining problem case is when the voltage_level
needs to increase due to a DDI port, but the CDCLK frequency
is decreasing (and not all pipes are being disabled). The
current approach will not bump the voltage level up until
after the port has already been enabled, which is too late.
But we'll take care of that case separately.
v2: Don't break the "must disable pipes case"
v3: Keep the on stack 'pipe' for future use
Cc: stable@vger.kernel.org
Fixes: d62686ba3b ("drm/i915/adl_p: CDCLK crawl support for ADL")
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240402155016.13733-2-ville.syrjala@linux.intel.com
(cherry picked from commit 3aecee90ac)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Pull x86 fixes from Ingo Molnar:
- Fix MCE timer reinit locking
- Fix/improve CoCo guest random entropy pool init
- Fix SEV-SNP late disable bugs
- Fix false positive objtool build warning
- Fix header dependency bug
- Fix resctrl CPU offlining bug
* tag 'x86-urgent-2024-04-07' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/retpoline: Add NOENDBR annotation to the SRSO dummy return thunk
x86/mce: Make sure to grab mce_sysfs_mutex in set_bank()
x86/CPU/AMD: Track SNP host status with cc_platform_*()
x86/cc: Add cc_platform_set/_clear() helpers
x86/kvm/Kconfig: Have KVM_AMD_SEV select ARCH_HAS_CC_PLATFORM
x86/coco: Require seeding RNG with RDRAND on CoCo systems
x86/numa/32: Include missing <asm/pgtable_areas.h>
x86/resctrl: Fix uninitialized memory read when last CPU of domain goes offline
Pull timer fixes from Ingo Molnar:
"Fix various timer bugs:
- Fix a timer migration bug that may result in missed events
- Fix timer migration group hierarchy event updates
- Fix a PowerPC64 build warning
- Fix a handful of DocBook annotation bugs"
* tag 'timers-urgent-2024-04-07' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timers/migration: Return early on deactivation
timers/migration: Fix ignored event due to missing CPU update
vdso: Use CONFIG_PAGE_SHIFT in vdso/datapage.h
timers: Fix text inconsistencies and spelling
tick/sched: Fix struct tick_sched doc warnings
tick/sched: Fix various kernel-doc warnings
timers: Fix kernel-doc format and add Return values
time/timekeeping: Fix kernel-doc warnings and typos
time/timecounter: Fix inline documentation
Pull x86 perf fix from Ingo Molnar:
"Fix a combined PEBS events bug on x86 Intel CPUs"
* tag 'perf-urgent-2024-04-07' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/ds: Don't clear ->pebs_data_cfg for the last PEBS event
Pull nfsd fixes from Chuck Lever:
- Address a slow memory leak with RPC-over-TCP
- Prevent another NFS4ERR_DELAY loop during CREATE_SESSION
* tag 'nfsd-6.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
nfsd: hold a lighter-weight client reference over CB_RECALL_ANY
SUNRPC: Fix a slow server-side memory leak with RPC-over-TCP
Pull xfs fix from Chandan Babu:
- Allow creating new links to special files which were not associated
with a project quota
* tag 'xfs-6.9-fixes-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: allow cross-linking special files without project quota
Pull smb client fixes from Steve French:
- fix to retry close to avoid potential handle leaks when server
returns EBUSY
- DFS fixes including a fix for potential use after free
- fscache fix
- minor strncpy cleanup
- reconnect race fix
- deal with various possible UAF race conditions tearing sessions down
* tag '6.9-rc2-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
smb: client: fix potential UAF in cifs_signal_cifsd_for_reconnect()
smb: client: fix potential UAF in smb2_is_network_name_deleted()
smb: client: fix potential UAF in is_valid_oplock_break()
smb: client: fix potential UAF in smb2_is_valid_oplock_break()
smb: client: fix potential UAF in smb2_is_valid_lease_break()
smb: client: fix potential UAF in cifs_stats_proc_show()
smb: client: fix potential UAF in cifs_stats_proc_write()
smb: client: fix potential UAF in cifs_dump_full_key()
smb: client: fix potential UAF in cifs_debug_files_proc_show()
smb3: retrying on failed server close
smb: client: serialise cifs_construct_tcon() with cifs_mount_mutex
smb: client: handle DFS tcons in cifs_construct_tcon()
smb: client: refresh referral without acquiring refpath_lock
smb: client: guarantee refcounted children from parent session
cifs: Fix caching to try to do open O_WRONLY as rdwr on server
smb: client: fix UAF in smb2_reconnect_server()
smb: client: replace deprecated strncpy with strscpy
srso_alias_untrain_ret() is special code, even if it is a dummy
which is called in the !SRSO case, so annotate it like its real
counterpart, to address the following objtool splat:
vmlinux.o: warning: objtool: .export_symbol+0x2b290: data relocation to !ENDBR: srso_alias_untrain_ret+0x0
Fixes: 4535e1a417 ("x86/bugs: Fix the SRSO mitigation on Zen3/4")
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/r/20240405144637.17908-1-bp@kernel.org
We want to fix:
0e11073247 ("x86/retpoline: Do the necessary fixup to the Zen3/4 srso return thunk for !SRSO")
So merge in Linus's latest into x86/urgent to have it available.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull firewire fixes from Takashi Sakamoto:
"The firewire-ohci kernel module has a parameter for verbose kernel
logging. It is well-known that it logs the spurious IRQ for bus-reset
event due to the unmasked register for IRQ event. This update fixes
the issue"
* tag 'firewire-fixes-6.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: ohci: mask bus reset interrupts between ISR and bottom half
In the FireWire OHCI interrupt handler, if a bus reset interrupt has
occurred, mask bus reset interrupts until bus_reset_work has serviced and
cleared the interrupt.
Normally, we always leave bus reset interrupts masked. We infer the bus
reset from the self-ID interrupt that happens shortly thereafter. A
scenario where we unmask bus reset interrupts was introduced in 2008 in
a007bb857e: If
OHCI_PARAM_DEBUG_BUSRESETS (8) is set in the debug parameter bitmask, we
will unmask bus reset interrupts so we can log them.
irq_handler logs the bus reset interrupt. However, we can't clear the bus
reset event flag in irq_handler, because we won't service the event until
later. irq_handler exits with the event flag still set. If the
corresponding interrupt is still unmasked, the first bus reset will
usually freeze the system due to irq_handler being called again each
time it exits. This freeze can be reproduced by loading firewire_ohci
with "modprobe firewire_ohci debug=-1" (to enable all debugging output).
Apparently there are also some cases where bus_reset_work will get called
soon enough to clear the event, and operation will continue normally.
This freeze was first reported a few months after a007bb85 was committed,
but until now it was never fixed. The debug level could safely be set
to -1 through sysfs after the module was loaded, but this would be
ineffectual in logging bus reset interrupts since they were only
unmasked during initialization.
irq_handler will now leave the event flag set but mask bus reset
interrupts, so irq_handler won't be called again and there will be no
freeze. If OHCI_PARAM_DEBUG_BUSRESETS is enabled, bus_reset_work will
unmask the interrupt after servicing the event, so future interrupts
will be caught as desired.
As a side effect to this change, OHCI_PARAM_DEBUG_BUSRESETS can now be
enabled through sysfs in addition to during initial module loading.
However, when enabled through sysfs, logging of bus reset interrupts will
be effective only starting with the second bus reset, after
bus_reset_work has executed.
Signed-off-by: Adam Goldman <adamg@pobox.com>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
