Currently the masking of ret with 0xff and followed by a right shift
of 8 bits always leaves a zero result. It appears the mask of 0xff
is incorrect and should be 0xff00, but I don't have the hardware to
test this. Fix this to mask the upper 8 bits before shifting.
[ Not tested ]
Addresses-Coverity: ("Operands don't affect result")
Fixes: 8fc8598e61 ("Staging: Added Realtek rtl8192u driver to staging")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200716154720.1710252-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jonathan writes:
First set of new device support, cleanups and features for IIO in the 5.9 cycle
Some new devices, but particularly good this time is the core rework coming
from Alexandru. Some of this has been in Analog's tree a long time, but other
parts are motivated by closing down common mistakes in new drivers.
Changes since first try at this pull request:
* Add missed patch to actually remove iio_priv_to_dev and as a result
also drop a few ingenic patches that need to be updated to take this
into account.
* Fix an ordering issue int he pollfunc attach in the core rework.
New device support
* qcom pmic7 adc
- New driver using common qcom-vadc library. Some associated cleanups and
refactors.
* invensense icm42600
- New driver supporting icm42600, icm42602, icm42605 and icm42622 via i2c
or spi. These are all 6 axis IMUs with gyro and accelerometers.
Driver supports buffered modes using the hardware fifo and interpolation
for accurate timestamps.
* sensirion scd30
- New driver for this carbon dioxide sensor including i2c and serial
interfaces + bindings.
Features
* ak8975
- Add reset gpio support.
* bma400
- Support SPI.
* bmc150
- Document and add support for bmc156b and bmm150b, tidy up _magn endings.
* bmi160
- Regulator and mount matrix support.
* mxc4005
- Add ID for mxc6655
* rockchip-saradc
- Triggered buffer support.
DT bindings
* qcom spmi-vadc converted to yaml + pmic7 bindings
* ak8975 tidy up and convert to yaml + add reset-gpio binding
* ingenic-adc -convert to yaml.
Core rework all carried through by Alexandru Ardelean.
* Assign parent device in the core rather than every driver. A few devices
need to provide specific non standard parents, so there is support for
overriding.
* Start to take parts of struct iio_dev opaque to the drivers.
This will be a long term job, but should reduce the number of drivers
we get that use parts that are currently only 'internal' by documentation.
* Move attach and detach of pollfunc to the core. Every triggered buffer
using driver had to do the same thing, so lets do it in the core. The
hard part here was getting all the drivers into canonical form so there
would be no functional changes in this final patch. That's taken quite
a lot of work over last couple of cycles!
Cleanups and minor fixes.
* docs
- Improve IIO_CONCENTRATION channel type description in ABI docs.
- Drop doubled word cases.
- Http to Https conversion.
* core
- Make iio_device_get_drvdata take a const struct iio_dev * avoiding some
nasty casts.
* ADCs
- Drop lots of users of of_match_ptr macro, includes of mod_devicetable.h
and CONFIG_OF protections. These prevent use of ACPI PRP0001 with these
drivers and get coppied into lots of new drivers.
* ad5380
- Constify iio_chan_spec_ext_info
* ad5592r
- Constify iio_chan_spec_ext_info
- Avoid use of iio_priv_to_dev (precursor to taking parts of iio_dev opaque)
* ad8366
- Make gpio optional as doesn't matter if its there or not.
* adis16480
- Use irq types instead of the flags.
* atlas-ezo-sensor
- Minimize scope of ret variable.
* at91-adc
- Add COMPILE_TEST dependency to driver to improve build coverage.
- Avoid use of iio_priv_to_dev (precursor to taking parts of iio_dev opaque)
* at91-sama5d2
- Avoid use of iio_priv_to_dev (precursor to taking parts of iio_dev opaque)
- Drop Ludovic as a co-maintaienr.
* cros_ec
- Reapply the range after resume.
- Add a read only frequency entry for legacy version.
- Typo fixes
* hts221
- Avoid use of iio_priv_to_dev (precursor to taking parts of iio_dev opaque)
* inv_mpu
- Drop double check on ACPI companion device.
* iqs621
- Avoid use of iio_priv_to_dev (precursor to taking parts of iio_dev opaque)
* iqs624
- Avoid use of iio_priv_to_dev (precursor to taking parts of iio_dev opaque)
* max11100
- Constify iio_chan_spec
* mmc35240
- Constify reg_default
* rockchip-saradc
- Move to managed allocators for everything in probe.
- Use more distinctive prefix for channel macros.
* stk3310
- Constify regmap_config.
* stm32-adc
- Avoid use of iio_priv_to_dev (precursor to taking parts of iio_dev opaque)
* stm32-dfsdm-adc
- Avoid use of iio_priv_to_dev (precursor to taking parts of iio_dev opaque)
* ti-am335x
- Use managed allocations where straight forward in probe function.
* tsl2563
- Avoid use of iio_priv_to_dev (precursor to taking parts of iio_dev opaque)
* tag 'iio-for-5.9a-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (107 commits)
iio: buffer: fix attach/detach pollfunc order
iio: core: remove iio_priv_to_dev() helper
Replace HTTP links with HTTPS ones: drivers/iio
Replace HTTP links with HTTPS ones: Documentation/devicetree/bindings/iio
dt-bindings: iio/adc: Convert ingenic-adc docs to YAML.
iio: cros_ec_accel_legacy: Add Read Only frequency entries
MAINTAINERS: adc: at91-sama5d2_adc: remove myself as co-maintainer
iio: adc: ti_am335x_adc: alloc kfifo & IRQ via devm_ functions
iio: adc: ti_am335x_adc: alloc channels via devm_kcalloc()
iio:adc:ingenic: drop of_match_ptr protection and include mod_devicetable.h
iio:adc:ti-tlc4541: Drop CONFIG_OF and of_match_ptr protections.
iio:adc:ti-adc161s626: Drop of_match_ptr protection.
iio:adc:ti-adc084s021: drop of_match_ptr protection
iio:adc:ti-adc0832: drop CONFIG_OF and of_match_ptr protections
iio:adc:ti-adc081c: Drop of_match_ptr and change to mod_devicetable.h
iio:adc:sd_adc_modulator: Drop of_match_ptr and tweak includes
iio:adc:mcp3422: remove CONFIG_OF and of_match_ptr protections
iio:adc:mcp320x: Drop CONFIG_OF and of_match_ptr protections
iio:adc:max1118: Drop CONFIG_OF / of_match_ptr protections
iio:adc:max11100: Drop of_match_ptr protection / add mod_devicetable.h include
...
At probe time, retrieve the MAC addresses of the switch ports using a
firmware call and use that to setup the switch interface net_device
instead of relying entirely on the user to configure a MAC address on
the interface. In case a switch interface is not connected to a MAC,
thus the dpsw_if_get_port_mac_addr() will return all zeroes, generate a
random MAC address and use that.
This new functionality is dependent on a firmware call which is
available only on newer versions, so depending on the running DPSW
object version skip this step.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20200714133431.17532-7-ioana.ciornei@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MC firmware will enable the switch interfaces at DPSW creation
without waiting for an 'ifconfig up' on the switch interfaces. When this
happens, the states held by the Linux software vs the firmware are not
in sync. Make sure to disable the switch ports at probe time to not
encounter this issue.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20200714133431.17532-5-ioana.ciornei@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are some cases where the switch interface needs to be disabled so
that changes in the configuration can be made. In such cases, we should
check for a running interface (bit __LINK_STATE_START of the netdev)
instead of netif_carrier_ok(). This is because on open() we enable the
switch interface even though the link up has not come out yet.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20200714133431.17532-4-ioana.ciornei@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All users of this helper have been updated to not use it.
Remove it now, so that we don't need to move it when creating the
iio_dev_opaque structure.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Reviewed-by: Matt Ranostay <matt.ranostay@konsulko.com> #for Matt's drivers
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200713091305.32708-1-grandmaster@al2klimov.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the textual documentation of Device Tree bindings for the
Ingenic JZ47xx SoCs ADC controller to YAML.
The `interrupts` property is now explicitly listed and marked as
required. While missing from the previous textual documentation, this
property has been used with all the boards which probe this driver.
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Tested-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Report to user space that 10Hz is the sampling frequency of
the accelerometers in legacy mode, and it can not be changed.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Eugen is, now, more active and up to date on this topic than I. So I let
him the full maintainance of this driver.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200708183117.16563-1-grandmaster@al2klimov.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code has the functionality to insert the GPIO lines using
the global GPIO numbers through module parameters.
As we are clearly deprecating the use of global GPIO numbers
look up the GPIO descriptors from the device instead. This
usually falls back to device hardware descriptions using e.g.
device tree or ACPI. This device clearly supports device
tree when used over SPI for example.
For example, this can be supplied in the device tree like so:
wfx@0x01 {
compatible = "silabs,wf200";
reset-gpios = <&gpio0 1>;
wakeup-gpios = <&gpio0 2>;
};
Cc: Jérôme Pouiller <jerome.pouiller@silabs.com>
Reviewed-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200703130756.514868-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This change attaches the life-cycle of the kfifo buffer & IRQ to the
parent-device. This in turn cleans up the exit & error paths, since we
don't need to explicitly cleanup these resources.
The main intent here is to remove the explicit cleanup of the
'indio_dev->buffer' via 'iio_kfifo_free(indio_dev->buffer);'.
As we want to add support for multiple buffers per IIO device, having it
exposed like this makes it tricky to consider a safe backwards compatible
approach for it.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change attaches the life-cycle of the channels array to the parent
device object that is attached to the IIO device.
This way we can remove from the cleanup code, the explicit
tiadc_channels_remove() which simply does a kfree() on the channels array.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Whilst it's unlikely this device will ever be instantiated using
ACPI, there is little advantage not assigning the of_device_id table in all
cases and it avoids providing an example that might be coppied into new
drivers.
Also include mod_devicetable.h whilst here as of_device_id is defined
in there so including the header is best practice.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Artur Rojek <contact@artur-rojek.eu>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
