The tlv320aic31xx devices allow to adjust the output common-mode voltage
for best analog performance. The datasheet states that the common mode
voltage should be set to be <= AVDD/2.
This changes allows to configure the output common-mode voltage via a DT
property. If the property is absent the voltage is automatically chosen
as the highest voltage below/equal to AVDD/2.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20191118151207.28576-1-l.stach@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
In case the RST line is connected to a GPIO line it needs to be pulled high
when the driver probes to be able to use the codec.
Add support also for cases when more than one codec is is controlled by the
same GPIO line by requesting the gpio with GPIOD_FLAGS_BIT_NONEXCLUSIVE.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191113124734.27984-3-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The current design of sending codec parameters assumes that decoders
will have parsers so they can parse the encoded stream for parameters
and configure the decoder.
But this assumption may not be universally true and we know some DSPs
which do not contain the parsers so additional parameters are required
to be passed.
So add these parameters starting with FLAC decoder. The size of
snd_codec_options is still 120 bytes after this change (due to this
being a union)
Co-developed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20191115102705.649976-2-vkoul@kernel.org
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
soc_cleanup_card_resources() will call card->remove(), but it should be
called if card->probe() or card->late_probe() are called.
snd_soc_bind_card() might be error before calling
card->probe() / card->late_probe().
In that time, card->remove() will be called.
This patch adds card_probed parameter to judge it.
Fixes: bfce78a559 ("ASoC: soc-core: tidyup soc_init_dai_link()")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/87o8xg4ltr.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It is easy to read code if it is cleanly using paired function/naming,
like start <-> stop, register <-> unregister, etc, etc.
But, current ALSA SoC code is very random, unbalance, not paired, etc.
It is easy to create bug at the such code, and it will be difficult to
debug.
snd_soc_bind_card() is calling snd_soc_dapm_init() for both
card and component.
Let's call paired snd_soc_dapm_shutdown() at paired
soc_cleanup_card_resources().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87r22c4lub.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_bind_card() is calling many initialize functions
for each card / link / dai / aux etc, etc, etc...
When error happen, the message is indicated at snd_soc_bind_card(),
not at each functions.
But, only soc_probe_aux_devices() case is indicating error at functions,
not at snd_soc_bind_card().
It is not an issue, but unbalanced.
This patch moves error message to snd_soc_bind_card().
Also avoids deep-nested code.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87lfsthkw9.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't need to separete snd_soc_add_dai_link() and
soc_bind_dai_link() anymore. Let's merge these.
One note is that before this patch, it adds list (A)
eventhough if it had dai_link->ignore (1), or already bounded dai_link (2).
But I guess it is wrong. This patch also solve this issue.
/* BEFORE */
int soc_bind_dai_link(...)
{
...
(1) if (dai_link->ignore)
return 0;
(2) if (soc_is_dai_link_bound(...))
return 0;
...
}
int snd_soc_add_dai_link(...)
{
...
=> ret = soc_bind_dai_link(...);
=> if (ret < 0)
=> return ret;
(A) list_add_tail(&dai_link->list, &card->dai_link_list);
...
}
/* AFTER */
int snd_soc_add_dai_link(...)
{
...
(1) if (dai_link->ignore)
return 0;
(2) if (soc_is_dai_link_bound(...))
return 0;
...
(A) list_add_tail(&dai_link->list, &card->dai_link_list);
return 0;
}
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87r22lhkx8.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Due to limitations of the clocking configuration, we have no way of
scheduling our hibernation before the bdw dsp hibernates. This causes
issues when the system suspends with an open stream. We need userspace
to toggle the kcontrol before we are suspended so that any writes on
suspend are not lost and we don't corrupt the regmap.
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191106011335.223061-9-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The irq is disabled at suspend to avoid running the threaded irq
handler after the codec has been powered off. At resume, codec irq is
re-enabled and the interrupt status register is checked to see if
headphone has been pluggnd/unplugged while the device is suspended.
There is still a chance that the headphone gets enabled or disabled
after the codec is suspended. disable_irq syncs the threaded irq
handler, but soc-jack's threaded irq handler schedules a delayed
work to poll gpios (for debounce). This is still OK. The codec won't
be powered back on again because all audio paths have been suspended,
and there are no force enabled supply widgets (MICBIAS1 is disabled).
The gpio status read after codec power off could be wrong, so the
gpio values are checked again after resume.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191106011335.223061-8-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
MCLK1 gets disabled at suspend and re-enabled at resume. Before
MCLK1 is re-enabled, if the DSP is already on (either the DSP was
left on during suspend, or the DSP is turned on early at resume),
i2c register read returns garbage and corrupts the regmap cache.
This patch stops the DSP before suspend and restarts it after
resume with a dalay to ensure MCLK is on while loading firmware.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191106011335.223061-7-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec dies when RT5677_PWR_ANLG2(MX-64h) is set to 0xACE1
while it's streaming audio over SPI. The DSP firmware turns
on PLL2 (MX-64 bit 8) when SPI streaming starts. However regmap
does not believe that register can change by itself. When
BST1 (bit 15) is turned on with regmap_update_bits(), it doesn't
read the register first before write, so PLL2 power bit is
cleared by accident.
Marking MX-64h as volatile in regmap solved the issue.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191106011335.223061-6-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Before a hotword is detected, GPIO1 pin is configured as IRQ
output so that jack detect works. When a hotword is detected,
the DSP firmware configures the GPIO1 pin as GPIO1 and
drives a 1. rt5677_irq() is called after a rising edge on
the GPIO1 pin, due to either jack detect event or hotword
event, or both. All possible events are checked and handled
in rt5677_irq() where GPIO1 pin is configured back to IRQ
output if a hotword is detected.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191106011335.223061-4-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The firmware rt5677_elf_vad is an ELF binary obtained from
request_firmware(). Sections of the ELF are loaded to
the DSP via SPI. A model (e.g. en_us.mmap) can optionally be
loaded to the DSP at RT5677_MODEL_ADDR to overwrite the
baked-in model in rt5677_elf_vad.
Then we switch to DSP mode, load firmware, and let DSP run.
When a hotword is detected, an interrupt is fired and
rt5677_irq() is called. When 'DSP VAD Switch' is turned off,
the codec is set back to normal mode.
The kcontrol 'DSP VAD Switch' is automatically enabled/disabled
when the hotwording PCM stream is opened/closed.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191106011335.223061-2-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
