Currently, in the AF_XDP transmit paths, the CIC bit of
TX Desc3 is set for all packets. Setting this bit for
packets transmitting through queues that don't support
checksum offloading causes the TX DMA to get stuck after
transmitting some packets. This patch ensures the CIC bit
of TX Desc3 is set only if the TX queue supports checksum
offloading.
Fixes: 132c32ee5b ("net: stmmac: Add TX via XDP zero-copy socket")
Signed-off-by: Rohan G Thomas <rohan.g.thomas@altera.com>
Reviewed-by: Matthew Gerlach <matthew.gerlach@altera.com>
Link: https://patch.msgid.link/20250825-xgmac-minor-fixes-v3-3-c225fe4444c0@altera.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Correct supported speed modes as per the XGMAC databook.
Commit 9cb54af214 ("net: stmmac: Fix IP-cores specific
MAC capabilities") removes support for 10M, 100M and
1000HD. 1000HD is not supported by XGMAC IP, but it does
support 10M and 100M FD mode for XGMAC version >= 2_20,
and it also supports 10M and 100M HD mode if the HDSEL bit
is set in the MAC_HW_FEATURE0 reg. This commit enables support
for 10M and 100M speed modes for XGMAC IP based on XGMAC
version and MAC capabilities.
Fixes: 9cb54af214 ("net: stmmac: Fix IP-cores specific MAC capabilities")
Signed-off-by: Rohan G Thomas <rohan.g.thomas@altera.com>
Reviewed-by: Matthew Gerlach <matthew.gerlach@altera.com>
Link: https://patch.msgid.link/20250825-xgmac-minor-fixes-v3-2-c225fe4444c0@altera.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Enabling RX FIFO Overflow interrupts is counterproductive
and causes an interrupt storm when RX FIFO overflows.
Disabling this interrupt has no side effect and eliminates
interrupt storms when the RX FIFO overflows.
Commit 8a7cb245cf ("net: stmmac: Do not enable RX FIFO
overflow interrupts") disables RX FIFO overflow interrupts
for DWMAC4 IP and removes the corresponding handling of
this interrupt. This patch is doing the same thing for
XGMAC IP.
Fixes: 2142754f8b ("net: stmmac: Add MAC related callbacks for XGMAC2")
Signed-off-by: Rohan G Thomas <rohan.g.thomas@altera.com>
Reviewed-by: Matthew Gerlach <matthew.gerlach@altera.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250825-xgmac-minor-fixes-v3-1-c225fe4444c0@altera.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Xon/Xoff sizes are derived from calculations that include
the port speed.
These settings need to be updated and applied whenever the
port speed is changed.
The port speed is typically set after the physical link goes down
and is negotiated as part of the link-up process between the two
connected interfaces.
Xon/Xoff parameters being updated at the point where the new
negotiated speed is established.
Fixes: 0696d60853 ("net/mlx5e: Receive buffer configuration")
Signed-off-by: Alexei Lazar <alazar@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250825143435.598584-11-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Changing flow steering modes is not allowed when eswitch is in switchdev
mode. This fix ensures that any steering mode change, including to
firmware steering, is correctly blocked while eswitch mode is switchdev.
Fixes: e890acd5ff ("net/mlx5: Add devlink flow_steering_mode parameter")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250825143435.598584-9-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If PF (Physical Function) has SFs (Sub-Functions), since the SFs are not
taking part in the synchronization flow, sync reset can lead to fatal
error on the SFs, as the function will be closed unexpectedly from the
SF point of view.
Add a check to prevent sync reset when there are SFs on a PF device
which is not ECPF, as ECPF is teardowned gracefully before reset.
Fixes: 92501fa6e4 ("net/mlx5: Ack on sync_reset_request only if PF can do reset_now")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250825143435.598584-8-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The devlink reload fw_activate command performs firmware activation
followed by driver reload, while devlink reload driver_reinit triggers
only driver reload. However, the driver reload logic differs between the
two modes, as on driver_reinit mode mlx5 also reloads auxiliary drivers,
while in fw_activate mode the auxiliary drivers are suspended where
applicable.
Additionally, following the cited commit, if the device has multiple PFs,
the behavior during fw_activate may vary between PFs: one PF may suspend
auxiliary drivers, while another reloads them.
Align devlink dev reload fw_activate behavior with devlink dev reload
driver_reinit, to reload all auxiliary drivers.
Fixes: 72ed5d5624 ("net/mlx5: Suspend auxiliary devices only in case of PCI device suspend")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Akiva Goldberger <agoldberger@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250825143435.598584-6-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In mlx5hws_pat_get_pattern(), when mlx5hws_pat_add_pattern_to_cache()
fails, the function attempts to clean up the pattern created by
mlx5hws_cmd_header_modify_pattern_create(). However, it incorrectly
uses *pattern_id which hasn't been set yet, instead of the local
ptrn_id variable that contains the actual pattern ID.
This results in attempting to destroy a pattern using uninitialized
data from the output parameter, rather than the valid pattern ID
returned by the firmware.
Use ptrn_id instead of *pattern_id in the cleanup path to properly
destroy the created pattern.
Fixes: aefc15a0fa ("net/mlx5: HWS, added modify header pattern and args handling")
Signed-off-by: Lama Kayal <lkayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250825143435.598584-5-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In mlx5hws_pat_calc_nop(), src_field and dst_field are passed to
hws_action_modify_get_target_fields() which should set their values.
However, if an invalid action type is encountered, these variables
remain uninitialized and are later used to update prev_src_field
and prev_dst_field.
Initialize both variables to INVALID_FIELD to ensure they have
defined values in all code paths.
Fixes: 01e035fd03 ("net/mlx5: HWS, handle modify header actions dependency")
Signed-off-by: Lama Kayal <lkayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250825143435.598584-4-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2025-08-25 (ice, ixgbe)
For ice:
Emil adds a check to ensure auxiliary device was created before tear
down to prevent NULL a pointer dereference.
Jake reworks flow for failed Tx scheduler configuration to allow for
proper recovery and operation. He also adjusts ice_adapter index for
E825C devices as use of DSN is incompatible with this device.
Michal corrects tracking of buffer allocation failure in
ice_clean_rx_irq().
For ixgbe:
Jedrzej adds __packed attribute to ixgbe_orom_civd_info to compatibility
with device OROM data.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ixgbe: fix ixgbe_orom_civd_info struct layout
ice: fix incorrect counter for buffer allocation failures
ice: use fixed adapter index for E825C embedded devices
ice: don't leave device non-functional if Tx scheduler config fails
ice: fix NULL pointer dereference in ice_unplug_aux_dev() on reset
====================
Link: https://patch.msgid.link/20250825215019.3442873-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Michael Chan says:
====================
bnxt_en: 3 bug fixes
The first one fixes a memory corruption issue that can happen when
FW resources change during ifdown with TCs created. The next two
fix FW resource reservation logic for TX rings and stats context.
====================
Link: https://patch.msgid.link/20250825175927.459987-1-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The HW resource reservation logic allows the L2 driver to use the
RoCE resources if the RoCE driver is not registered. When calculating
the stats contexts available for L2, we should not blindly subtract
the stats contexts reserved for RoCE unless the RoCE driver is
registered. This bug may cause the L2 rings to be less than the
number requested when we are close to running out of stats contexts.
Fixes: 2e4592dc9b ("bnxt_en: Change MSIX/NQs allocation policy")
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250825175927.459987-4-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Before we accept an ethtool request to increase a resource (such as
rings), we call the FW to check that the requested resource is likely
available first before we commit. But it is still possible that
the actual reservation or allocation can fail. The existing code
is missing the logic to adjust the TX rings in case the reserved
TX rings are less than requested. Add a warning message (a similar
message for RX rings already exists) and add the logic to adjust
the TX rings. Without this fix, the number of TX rings reported
to the stack can exceed the actual TX rings and ethtool -l will
report more than the actual TX rings.
Fixes: 674f50a5b0 ("bnxt_en: Implement new method to reserve rings.")
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250825175927.459987-3-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
bnxt_set_dflt_rings() assumes that it is always called before any TC has
been created. So it doesn't take bp->num_tc into account and assumes
that it is always 0 or 1.
In the FW resource or capability change scenario, the FW will return
flags in bnxt_hwrm_if_change() that will cause the driver to
reinitialize and call bnxt_cancel_reservations(). This will lead to
bnxt_init_dflt_ring_mode() calling bnxt_set_dflt_rings() and bp->num_tc
may be greater than 1. This will cause bp->tx_ring[] to be sized too
small and cause memory corruption in bnxt_alloc_cp_rings().
Fix it by properly scaling the TX rings by bp->num_tc in the code
paths mentioned above. Add 2 helper functions to determine
bp->tx_nr_rings and bp->tx_nr_rings_per_tc.
Fixes: ec5d31e3c1 ("bnxt_en: Handle firmware reset status during IF_UP.")
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250825175927.459987-2-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The previous maintainer, Joyce Ooi, is no longer with the company,
and her email is no longer reachable. As a result, the maintainer
information for the Altera Triple Speed Ethernet Driver has been updated.
Changes:
- Replaced Joyce Ooi's email with Boon Khai Ng's email address.
- Kept the component's status as "Maintained".
Signed-off-by: Boon Khai Ng <boon.khai.ng@altera.com>
Link: https://patch.msgid.link/20250825071321.30131-1-boon.khai.ng@altera.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
hw_stats now has only one variable for tx_octets/rx_octets, so we should
only increment p once, not twice. This would cause the statistics to be
reported under the wrong categories in `ethtool -S --all-groups` (which
uses hw_stats) but not `ethtool -S` (which uses ethtool_stats).
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Fixes: f6af690a29 ("net: cadence: macb: Report standard stats")
Link: https://patch.msgid.link/20250825172134.681861-1-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There's a steady stream of TLS changes and bugs. We need active
maintainers in this area, and Boris hasn't been participating
much in upstream work. Move him to CREDITS. While at it also
add Dave Watson there who was the author of the initial SW
implementation, AFAIU.
Link: https://patch.msgid.link/20250825155753.2178045-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
`McstFramesRcvdOk` counts the number of received multicast packets, and
it reports the value correctly.
However, reading `McstFramesRcvdOk` clears the register to zero. As a
result, the driver was reporting only the packets since the last read,
instead of the accumulated total.
Fix this by updating the multicast statistics accumulatively instaed of
instantaneously.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-on: D-Link DGE-550T Rev-A3
Signed-off-by: Yeounsu Moon <yyyynoom@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250823182927.6063-3-yyyynoom@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Before configuring the NIX block, the AF driver initiates the
"NIX block X2P bus calibration" and verifies that NIX interfaces
such as CGX and LBK are active and functioning correctly.
On few silicon variants(CNF10KA and CNF10KB), X2P calibration failures
have been observed on some CGX blocks that are not mapped to the NIX block.
Since both NIX-mapped and non-NIX-mapped CGX blocks share the same
VENDOR,DEVICE,SUBSYS_DEVID, it's not possible to skip probe based on
these parameters.
This patch introuduces "is_cgx_mapped_to_nix" API to detect and skip
probe of non NIX mapped CGX blocks.
Fixes: aba53d5dbc ("octeontx2-af: NIX block admin queue init")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Link: https://patch.msgid.link/20250822105805.2236528-1-hkelam@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current layout of struct ixgbe_orom_civd_info causes incorrect data
storage due to compiler-inserted padding. This results in issues when
writing OROM data into the structure.
Add the __packed attribute to ensure the structure layout matches the
expected binary format without padding.
Fixes: 70db0788a2 ("ixgbe: read the OROM version information")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, the driver increments `alloc_page_failed` when buffer allocation fails
in `ice_clean_rx_irq()`. However, this counter is intended for page allocation
failures, not buffer allocation issues.
This patch corrects the counter by incrementing `alloc_buf_failed` instead,
ensuring accurate statistics reporting for buffer allocation failures.
Fixes: 2fba7dc515 ("ice: Add support for XDP multi-buffer on Rx side")
Reported-by: Jacob Keller <jacob.e.keller@intel.com>
Suggested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Priya Singh <priyax.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_adapter structure is used by the ice driver to connect multiple
physical functions of a device in software. It was introduced by
commit 0e2bddf9e5 ("ice: add ice_adapter for shared data across PFs on
the same NIC") and is primarily used for PTP support, as well as for
handling certain cross-PF synchronization.
The original design of ice_adapter used PCI address information to
determine which devices should be connected. This was extended to support
E825C devices by commit fdb7f54700 ("ice: Initial support for E825C
hardware in ice_adapter"), which used the device ID for E825C devices
instead of the PCI address.
Later, commit 0093cb194a ("ice: use DSN instead of PCI BDF for
ice_adapter index") replaced the use of Bus/Device/Function addressing with
use of the device serial number.
E825C devices may appear in "Dual NAC" configuration which has multiple
physical devices tied to the same clock source and which need to use the
same ice_adapter. Unfortunately, each "NAC" has its own NVM which has its
own unique Device Serial Number. Thus, use of the DSN for connecting
ice_adapter does not work properly. It "worked" in the pre-production
systems because the DSN was not initialized on the test NVMs and all the
NACs had the same zero'd serial number.
Since we cannot rely on the DSN, lets fall back to the logic in the
original E825C support which used the device ID. This is safe for E825C
only because of the embedded nature of the device. It isn't a discreet
adapter that can be plugged into an arbitrary system. All E825C devices on
a given system are connected to the same clock source and need to be
configured through the same PTP clock.
To make this separation clear, reserve bit 63 of the 64-bit index values as
a "fixed index" indicator. Always clear this bit when using the device
serial number as an index.
For E825C, use a fixed value defined as the 0x579C E825C backplane device
ID bitwise ORed with the fixed index indicator. This is slightly different
than the original logic of just using the device ID directly. Doing so
prevents a potential issue with systems where only one of the NACs is
connected with an external PHY over SGMII. In that case, one NAC would
have the E825C_SGMII device ID, but the other would not.
Separate the determination of the full 64-bit index from the 32-bit
reduction logic. Provide both ice_adapter_index() and a wrapping
ice_adapter_xa_index() which handles reducing the index to a long on 32-bit
systems. As before, cache the full index value in the adapter structure to
warn about collisions.
This fixes issues with E825C not initializing PTP on both NACs, due to
failure to connect the appropriate devices to the same ice_adapter.
Fixes: 0093cb194a ("ice: use DSN instead of PCI BDF for ice_adapter index")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_cfg_tx_topo function attempts to apply Tx scheduler topology
configuration based on NVM parameters, selecting either a 5 or 9 layer
topology.
As part of this flow, the driver acquires the "Global Configuration Lock",
which is a hardware resource associated with programming the DDP package
to the device. This "lock" is implemented by firmware as a way to
guarantee that only one PF can program the DDP for a device. Unlike a
traditional lock, once a PF has acquired this lock, no other PF will be
able to acquire it again (including that PF) until a CORER of the device.
Future requests to acquire the lock report that global configuration has
already completed.
The following flow is used to program the Tx topology:
* Read the DDP package for scheduler configuration data
* Acquire the global configuration lock
* Program Tx scheduler topology according to DDP package data
* Trigger a CORER which clears the global configuration lock
This is followed by the flow for programming the DDP package:
* Acquire the global configuration lock (again)
* Download the DDP package to the device
* Release the global configuration lock.
However, if configuration of the Tx topology fails, (i.e.
ice_get_set_tx_topo returns an error code), the driver exits
ice_cfg_tx_topo() immediately, and fails to trigger CORER.
While the global configuration lock is held, the firmware rejects most
AdminQ commands, as it is waiting for the DDP package download (or Tx
scheduler topology programming) to occur.
The current driver flows assume that the global configuration lock has been
reset by CORER after programming the Tx topology. Thus, the same PF
attempts to acquire the global lock again, and fails. This results in the
driver reporting "an unknown error occurred when loading the DDP package".
It then attempts to enter safe mode, but ultimately fails to finish
ice_probe() since nearly all AdminQ command report error codes, and the
driver stops loading the device at some point during its initialization.
The only currently known way that ice_get_set_tx_topo() can fail is with
certain older DDP packages which contain invalid topology configuration, on
firmware versions which strictly validate this data. The most recent
releases of the DDP have resolved the invalid data. However, it is still
poor practice to essentially brick the device, and prevent access to the
device even through safe mode or recovery mode. It is also plausible that
this command could fail for some other reason in the future.
We cannot simply release the global lock after a failed call to
ice_get_set_tx_topo(). Releasing the lock indicates to firmware that global
configuration (downloading of the DDP) has completed. Future attempts by
this or other PFs to load the DDP will fail with a report that the DDP
package has already been downloaded. Then, PFs will enter safe mode as they
realize that the package on the device does not meet the minimum version
requirement to load. The reported error messages are confusing, as they
indicate the version of the default "safe mode" package in the NVM, rather
than the version of the file loaded from /lib/firmware.
Instead, we need to trigger CORER to clear global configuration. This is
the lowest level of hardware reset which clears the global configuration
lock and related state. It also clears any already downloaded DDP.
Crucially, it does *not* clear the Tx scheduler topology configuration.
Refactor ice_cfg_tx_topo() to always trigger a CORER after acquiring the
global lock, regardless of success or failure of the topology
configuration.
We need to re-initialize the HW structure when we trigger the CORER. Thus,
it makes sense for this to be the responsibility of ice_cfg_tx_topo()
rather than its caller, ice_init_tx_topology(). This avoids needless
re-initialization in cases where we don't attempt to update the Tx
scheduler topology, such as if it has already been programmed.
There is one catch: failure to re-initialize the HW struct should stop
ice_probe(). If this function fails, we won't have a valid HW structure and
cannot ensure the device is functioning properly. To handle this, ensure
ice_cfg_tx_topo() returns a limited set of error codes. Set aside one
specifically, -ENODEV, to indicate that the ice_init_tx_topology() should
fail and stop probe.
Other error codes indicate failure to apply the Tx scheduler topology. This
is treated as a non-fatal error, with an informational message informing
the system administrator that the updated Tx topology did not apply. This
allows the device to load and function with the default Tx scheduler
topology, rather than failing to load entirely.
Note that this use of CORER will not result in loops with future PFs
attempting to also load the invalid Tx topology configuration. The first PF
will acquire the global configuration lock as part of programming the DDP.
Each PF after this will attempt to acquire the global lock as part of
programming the Tx topology, and will fail with the indication from
firmware that global configuration is already complete. Tx scheduler
topology configuration is only performed during driver init (probe or
devlink reload) and not during cleanup for a CORER that happens after probe
completes.
Fixes: 91427e6d90 ("ice: Support 5 layer topology")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Issuing a reset when the driver is loaded without RDMA support, will
results in a crash as it attempts to remove RDMA's non-existent auxbus
device:
echo 1 > /sys/class/net/<if>/device/reset
BUG: kernel NULL pointer dereference, address: 0000000000000008
...
RIP: 0010:ice_unplug_aux_dev+0x29/0x70 [ice]
...
Call Trace:
<TASK>
ice_prepare_for_reset+0x77/0x260 [ice]
pci_dev_save_and_disable+0x2c/0x70
pci_reset_function+0x88/0x130
reset_store+0x5a/0xa0
kernfs_fop_write_iter+0x15e/0x210
vfs_write+0x273/0x520
ksys_write+0x6b/0xe0
do_syscall_64+0x79/0x3b0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
ice_unplug_aux_dev() checks pf->cdev_info->adev for NULL pointer, but
pf->cdev_info will also be NULL, leading to the deref in the trace above.
Introduce a flag to be set when the creation of the auxbus device is
successful, to avoid multiple NULL pointer checks in ice_unplug_aux_dev().
Fixes: c24a65b6a2 ("iidc/ice/irdma: Update IDC to support multiple consumers")
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
* tag 'for-net-2025-08-22' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: hci_sync: fix set_local_name race condition
Bluetooth: hci_event: Disconnect device when BIG sync is lost
Bluetooth: hci_event: Detect if HCI_EV_NUM_COMP_PKTS is unbalanced
Bluetooth: hci_event: Mark connection as closed during suspend disconnect
Bluetooth: hci_event: Treat UNKNOWN_CONN_ID on disconnect as success
Bluetooth: hci_conn: Make unacked packet handling more robust
====================
Link: https://patch.msgid.link/20250822180230.345979-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
idpf: replace Tx flow scheduling buffer ring with buffer pool
Joshua Hay says:
This series fixes a stability issue in the flow scheduling Tx send/clean
path that results in a Tx timeout.
The existing guardrails in the Tx path were not sufficient to prevent
the driver from reusing completion tags that were still in flight (held
by the HW). This collision would cause the driver to erroneously clean
the wrong packet thus leaving the descriptor ring in a bad state.
The main point of this fix is to replace the flow scheduling buffer ring
with a large pool/array of buffers. The completion tag then simply is
the index into this array. The driver tracks the free tags and pulls
the next free one from a refillq. The cleaning routines simply use the
completion tag from the completion descriptor to index into the array to
quickly find the buffers to clean.
All of the code to support this is added first to ensure traffic still
passes with each patch. The final patch then removes all of the
obsolete stashing code.
* '200GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
idpf: remove obsolete stashing code
idpf: stop Tx if there are insufficient buffer resources
idpf: replace flow scheduling buffer ring with buffer pool
idpf: simplify and fix splitq Tx packet rollback error path
idpf: improve when to set RE bit logic
idpf: add support for Tx refillqs in flow scheduling mode
====================
Link: https://patch.msgid.link/20250821180100.401955-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Once driver submits the packets to the hardware, each packet
traverse through multiple transmit levels in the following
order:
SMQ -> TL4 -> TL3 -> TL2 -> TL1
The SMQ supports configurable minimum and maximum packet sizes.
It enters to a hang state, if driver submits packets with
out of bound lengths.
To avoid the same, implement packet length validation before
submitting packets to the hardware. Increment tx_dropped counter
on failure.
Fixes: 3184fb5ba9 ("octeontx2-vf: Virtual function driver support")
Fixes: 22f8587967 ("octeontx2-pf: Add basic net_device_ops")
Fixes: 3ca6c4c882 ("octeontx2-pf: Add packet transmission support")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Link: https://patch.msgid.link/20250821062528.1697992-1-hkelam@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Function set_name_sync() uses hdev->dev_name field to send
HCI_OP_WRITE_LOCAL_NAME command, but copying from data to hdev->dev_name
is called after mgmt cmd was queued, so it is possible that function
set_name_sync() will read old name value.
This change adds name as a parameter for function hci_update_name_sync()
to avoid race condition.
Fixes: 6f6ff38a1e ("Bluetooth: hci_sync: Convert MGMT_OP_SET_LOCAL_NAME")
Signed-off-by: Pavel Shpakovskiy <pashpakovskii@salutedevices.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When a BIG sync is lost, the device should be set to "disconnected".
This ensures symmetry with the ISO path setup, where the device is
marked as "connected" once the path is established. Without this
change, the device state remains inconsistent and may lead to a
memory leak.
Fixes: b2a5f2e1c1 ("Bluetooth: hci_event: Add support for handling LE BIG Sync Lost event")
Signed-off-by: Yang Li <yang.li@amlogic.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This attempts to detect if HCI_EV_NUM_COMP_PKTS contain an unbalanced
(more than currently considered outstanding) number of packets otherwise
it could cause the hcon->sent to underflow and loop around breaking the
tracking of the outstanding packets pending acknowledgment.
Fixes: f428091858 ("Bluetooth: Simplify num_comp_pkts_evt function")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When suspending, the disconnect command for an active Bluetooth
connection could be issued, but the corresponding
`HCI_EV_DISCONN_COMPLETE` event might not be received before the system
completes the suspend process. This can lead to an inconsistent state.
On resume, the controller may auto-accept reconnections from the same
device (due to suspend event filters), but these new connections are
rejected by the kernel which still has connection objects from before
suspend. Resulting in errors like:
```
kernel: Bluetooth: hci0: ACL packet for unknown connection handle 1
kernel: Bluetooth: hci0: Ignoring HCI_Connection_Complete for existing
connection
```
This is a btmon snippet that shows the issue:
```
< HCI Command: Disconnect (0x01|0x0006) plen 3
Handle: 1 Address: 78:20:A5:4A:DF:28 (Nintendo Co.,Ltd)
Reason: Remote User Terminated Connection (0x13)
> HCI Event: Command Status (0x0f) plen 4
Disconnect (0x01|0x0006) ncmd 2
Status: Success (0x00)
[...]
// Host suspends with the event filter set for the device
// On resume, the device tries to reconnect with a new handle
> HCI Event: Connect Complete (0x03) plen 11
Status: Success (0x00)
Handle: 2
Address: 78:20:A5:4A:DF:28 (Nintendo Co.,Ltd)
// Kernel ignores this event because there is an existing connection
with
// handle 1
```
By explicitly setting the connection state to BT_CLOSED we can ensure a
consistent state, even if we don't receive the disconnect complete event
in time.
Link: https://github.com/bluez/bluez/issues/1226
Fixes: 182ee45da0 ("Bluetooth: hci_sync: Rework hci_suspend_notifier")
Signed-off-by: Ludovico de Nittis <ludovico.denittis@collabora.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When the host sends an HCI_OP_DISCONNECT command, the controller may
respond with the status HCI_ERROR_UNKNOWN_CONN_ID (0x02). E.g. this can
happen on resume from suspend, if the link was terminated by the remote
device before the event mask was correctly set.
This is a btmon snippet that shows the issue:
```
> ACL Data RX: Handle 3 flags 0x02 dlen 12
L2CAP: Disconnection Request (0x06) ident 5 len 4
Destination CID: 65
Source CID: 72
< ACL Data TX: Handle 3 flags 0x00 dlen 12
L2CAP: Disconnection Response (0x07) ident 5 len 4
Destination CID: 65
Source CID: 72
> ACL Data RX: Handle 3 flags 0x02 dlen 12
L2CAP: Disconnection Request (0x06) ident 6 len 4
Destination CID: 64
Source CID: 71
< ACL Data TX: Handle 3 flags 0x00 dlen 12
L2CAP: Disconnection Response (0x07) ident 6 len 4
Destination CID: 64
Source CID: 71
< HCI Command: Set Event Mask (0x03|0x0001) plen 8
Mask: 0x3dbff807fffbffff
Inquiry Complete
Inquiry Result
Connection Complete
Connection Request
Disconnection Complete
Authentication Complete
[...]
< HCI Command: Disconnect (0x01|0x0006) plen 3
Handle: 3 Address: 78:20:A5:4A:DF:28 (Nintendo Co.,Ltd)
Reason: Remote User Terminated Connection (0x13)
> HCI Event: Command Status (0x0f) plen 4
Disconnect (0x01|0x0006) ncmd 1
Status: Unknown Connection Identifier (0x02)
```
Currently, the hci_cs_disconnect function treats any non-zero status
as a command failure. This can be misleading because the connection is
indeed being terminated and the controller is confirming that is has no
knowledge of that connection handle. Meaning that the initial request of
disconnecting a device should be treated as done.
With this change we allow the function to proceed, following the success
path, which correctly calls `mgmt_device_disconnected` and ensures a
consistent state.
Link: https://github.com/bluez/bluez/issues/1226
Fixes: 182ee45da0 ("Bluetooth: hci_sync: Rework hci_suspend_notifier")
Signed-off-by: Ludovico de Nittis <ludovico.denittis@collabora.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This attempts to make unacked packet handling more robust by detecting
if there are no connections left then restore all buffers of the
respective pool.
Fixes: 5638d9ea9c ("Bluetooth: hci_conn: Fix not restoring ISO buffer count on disconnect")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When removing a macb device, the driver calls phy_exit() before
unregister_netdev(). This leads to a WARN from kernfs:
------------[ cut here ]------------
kernfs: can not remove 'attached_dev', no directory
WARNING: CPU: 1 PID: 27146 at fs/kernfs/dir.c:1683
Call trace:
kernfs_remove_by_name_ns+0xd8/0xf0
sysfs_remove_link+0x24/0x58
phy_detach+0x5c/0x168
phy_disconnect+0x4c/0x70
phylink_disconnect_phy+0x6c/0xc0 [phylink]
macb_close+0x6c/0x170 [macb]
...
macb_remove+0x60/0x168 [macb]
platform_remove+0x5c/0x80
...
The warning happens because the PHY is being exited while the netdev
is still registered. The correct order is to unregister the netdev
before shutting down the PHY and cleaning up the MDIO bus.
Fix this by moving unregister_netdev() ahead of phy_exit() in
macb_remove().
Fixes: 8b73fa3ae0 ("net: macb: Added ZynqMP-specific initialization")
Signed-off-by: luoguangfei <15388634752@163.com>
Link: https://patch.msgid.link/20250818232527.1316-1-15388634752@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Will Deacon says:
====================
Fix vsock error-handling regression introduced in v6.17-rc1
Here are a couple of patches fixing the vsock error-handling regression
found by syzbot that I introduced during the recent merge window.
====================
Link: https://patch.msgid.link/20250818180355.29275-1-will@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 6693731487 ("vsock/virtio: Allocate nonlinear SKBs for handling
large transmit buffers") converted the virtio vsock transmit path to
utilise nonlinear SKBs when handling large buffers. As part of this
change, virtio_transport_fill_skb() was updated to call
skb_copy_datagram_from_iter() instead of memcpy_from_msg() as the latter
expects a single destination buffer and cannot handle nonlinear SKBs
correctly.
Unfortunately, during this conversion, I overlooked the error case when
the copying function returns -EFAULT due to a fault on the input buffer
in userspace. In this case, memcpy_from_msg() reverts the iterator to
its initial state thanks to copy_from_iter_full() whereas
skb_copy_datagram_from_iter() leaves the iterator partially advanced.
This results in a WARN_ONCE() from the vsock code, which expects the
iterator to stay in sync with the number of bytes transmitted so that
virtio_transport_send_pkt_info() can return -EFAULT when it is called
again:
------------[ cut here ]------------
'send_pkt()' returns 0, but 65536 expected
WARNING: CPU: 0 PID: 5503 at net/vmw_vsock/virtio_transport_common.c:428 virtio_transport_send_pkt_info+0xd11/0xf00 net/vmw_vsock/virtio_transport_common.c:426
Modules linked in:
CPU: 0 UID: 0 PID: 5503 Comm: syz.0.17 Not tainted 6.16.0-syzkaller-12063-g37816488247d #0 PREEMPT(full)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014
Call virtio_transport_fill_skb_full() to restore the previous iterator
behaviour.
Cc: Jason Wang <jasowang@redhat.com>
Cc: Stefano Garzarella <sgarzare@redhat.com>
Fixes: 6693731487 ("vsock/virtio: Allocate nonlinear SKBs for handling large transmit buffers")
Reported-by: syzbot+b4d960daf7a3c7c2b7b1@syzkaller.appspotmail.com
Signed-off-by: Will Deacon <will@kernel.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Link: https://patch.msgid.link/20250818180355.29275-3-will@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull networking fixes from Jakub Kicinski:
"Including fixes from Bluetooth.
Current release - fix to a fix:
- usb: asix_devices: fix PHY address mask in MDIO bus initialization
Current release - regressions:
- Bluetooth: fixes for the split between BIS_LINK and PA_LINK
- Revert "net: cadence: macb: sama7g5_emac: Remove USARIO CLKEN
flag", breaks compatibility with some existing device tree blobs
- dsa: b53: fix reserved register access in b53_fdb_dump()
Current release - new code bugs:
- sched: dualpi2: run probability update timer in BH to avoid
deadlock
- eth: libwx: fix the size in RSS hash key population
- pse-pd: pd692x0: improve power budget error paths and handling
Previous releases - regressions:
- tls: fix handling of zero-length records on the rx_list
- hsr: reject HSR frame if skb can't hold tag
- bonding: fix negotiation flapping in 802.3ad passive mode
Previous releases - always broken:
- gso: forbid IPv6 TSO with extensions on devices with only IPV6_CSUM
- sched: make cake_enqueue return NET_XMIT_CN when past buffer_limit,
avoid packet drops with low buffer_limit, remove unnecessary WARN()
- sched: fix backlog accounting after modifying config of a qdisc in
the middle of the hierarchy
- mptcp: improve handling of skb extension allocation failures
- eth: mlx5:
- fixes for the "HW Steering" flow management method
- fixes for QoS and device buffer management"
* tag 'net-6.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (81 commits)
netfilter: nf_reject: don't leak dst refcount for loopback packets
net/mlx5e: Preserve shared buffer capacity during headroom updates
net/mlx5e: Query FW for buffer ownership
net/mlx5: Restore missing scheduling node cleanup on vport enable failure
net/mlx5: Fix QoS reference leak in vport enable error path
net/mlx5: Destroy vport QoS element when no configuration remains
net/mlx5e: Preserve tc-bw during parent changes
net/mlx5: Remove default QoS group and attach vports directly to root TSAR
net/mlx5: Base ECVF devlink port attrs from 0
net: pse-pd: pd692x0: Skip power budget configuration when undefined
net: pse-pd: pd692x0: Fix power budget leak in manager setup error path
Octeontx2-af: Skip overlap check for SPI field
selftests: tls: add tests for zero-length records
tls: fix handling of zero-length records on the rx_list
net: airoha: ppe: Do not invalid PPE entries in case of SW hash collision
selftests: bonding: add test for passive LACP mode
bonding: send LACPDUs periodically in passive mode after receiving partner's LACPDU
bonding: update LACP activity flag after setting lacp_active
Revert "net: cadence: macb: sama7g5_emac: Remove USARIO CLKEN flag"
ipv6: sr: Fix MAC comparison to be constant-time
...
recent patches to add a WARN() when replacing skb dst entry found an
old bug:
WARNING: include/linux/skbuff.h:1165 skb_dst_check_unset include/linux/skbuff.h:1164 [inline]
WARNING: include/linux/skbuff.h:1165 skb_dst_set include/linux/skbuff.h:1210 [inline]
WARNING: include/linux/skbuff.h:1165 nf_reject_fill_skb_dst+0x2a4/0x330 net/ipv4/netfilter/nf_reject_ipv4.c:234
[..]
Call Trace:
nf_send_unreach+0x17b/0x6e0 net/ipv4/netfilter/nf_reject_ipv4.c:325
nft_reject_inet_eval+0x4bc/0x690 net/netfilter/nft_reject_inet.c:27
expr_call_ops_eval net/netfilter/nf_tables_core.c:237 [inline]
..
This is because blamed commit forgot about loopback packets.
Such packets already have a dst_entry attached, even at PRE_ROUTING stage.
Instead of checking hook just check if the skb already has a route
attached to it.
Fixes: f53b9b0bdc ("netfilter: introduce support for reject at prerouting stage")
Signed-off-by: Florian Westphal <fw@strlen.de>
Link: https://patch.msgid.link/20250820123707.10671-1-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
