The regmap is configured for 8 bit registers, uses a RB-Tree cache and
marks several registers as volatile (i.e. do not cache).
The ALS and PS data registers in the chip are 16 bit wide and spans
two regmap registers. In the current driver only the base register is
marked as volatile, resulting in the upper register only read once.
Further the data sheet notes:
| When the I2C read operation starts, all four ALS data registers are
| locked until the I2C read operation of register 0x8B is completed.
Which results in the registers never update after the 2nd read.
This patch fixes the problem by marking the upper 8 bits of the ALS
and PS registers as volatile, too.
Fixes: 2f2c96338a ("iio: ltr501: Add regmap support.")
Reported-by: Oliver Lang <Oliver.Lang@gossenmetrawatt.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Nikita Travkin <nikita@trvn.ru> # ltr559
Link: https://lore.kernel.org/r/20210610134619.2101372-2-mkl@pengutronix.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Commit c1d1c4a62d ("iio: accel: bma180: BMA254 support") added
BMA254 support to the bma180 driver and changed some naming to BMA25x
to make it easier to add support for BMA253 and BMA255.
Unfortunately, there is quite some overlap between the bma180 driver
and the bmc150-accel driver. Back when the commit was made, the
bmc150-accel driver actually already had support for BMA255, and
adding support for BMA254 would have been as simple as adding a new
compatible to bmc150-accel.
The bmc150-accel driver is a bit better for BMA254 since it also
supports the motion trigger/interrupt functionality. Fortunately,
moving BMA254 support over to bmc150-accel is fairly simple because
the drivers have compatible device tree bindings.
Revert most of the changes for BMA254 support in bma180 and move
BMA254 over to bmc150-accel. This has the following advantages:
- Support for motion trigger/interrupt
- Fix incorrect scale values (BMA254 currently uses the same as
BMA250 but actually they're different because of 10 vs 12 bits
data size)
- Less code than before :)
BMA250 could be potentially also moved but it's more complicated
because its chip_id conflicts with the one for BMA222 in bmc150-accel.
Perhaps there are also other register differences, I did not investigate
further yet (and I have no way to test it).
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210611080903.14384-11-stephan@gerhold.net
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
BMA253 has two interrupt pins (INT1 and INT2) that can be configured
independently. At the moment the bmc150-accel driver does not make use
of them but it might be able to in the future, so it's useful to already
specify all available interrupts in the device tree.
Set maxItems: 2 for interrupts to allow specifying a second one.
This is necessary as preparation to move the bosch,bma254 compatible
from bosch,bma180.yaml to bosch,bma255.yaml since bma180 allows two
interrupts, but BMA254 is better supported by the bmc150-accel driver.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210611080903.14384-9-stephan@gerhold.net
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The chips supported by the bmc150-accel driver are clearly documented
in Kconfig, in the bmc150_accel_chip_info_tbl as well as in all the
device ID tables in the I2C/SPI drivers. It's easy to forget to update
the lists in the file header. Drop those entirely to reduce the amount
of changes required to add new chip variants.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210611080903.14384-5-stephan@gerhold.net
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Commit 0ad4bf3701 ("iio:accel:bmc150-accel: Use the chip ID to detect
sensor variant") stopped using the I2C/ACPI match data to look up the
bmc150_accel_chip_info. However, the bmc150_accel_chip_info_tbl remained
as-is, with multiple entries with the same chip_id (e.g. 0xFA for
BMC150/BMI055/BMA255). This is redundant now because actually the driver
will always select the first entry with a matching chip_id.
So even if a device probes e.g. with BMA0255 it will end up using the
chip_info for BMC150. And in general that's fine for now, the entries
for BMC150/BMI055/BMA255 were exactly the same anyway (except for the
name, which is replaced with the more accurate one later).
But in this case it's misleading because it suggests that one should
add even more entries with the same chip_id when adding support for
new variants. Let's make that more clear by removing the enum with
the chip identifiers entirely and instead have only one entry per
chip_id.
Note that we may need to bring back some mechanism to differentiate
between different chips with the same chip_id in the future.
For example, BMA250 (currently supported by the bma180 driver) has the
same chip_id = 0x03 as BMA222 even though they have different channel
sizes (8 bits vs 10 bits). But in any case, that mechanism would
need to look quite different from what we have right now.
Cc: Bastien Nocera <hadess@hadess.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210611080903.14384-4-stephan@gerhold.net
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The Kconfig option currently says that all Bosch accelerometers
supported by the bmc150-accel driver are combo chips with both
accelerometer and magnetometer. This is wrong: actually only BMC150
is such a combo. The BMA* variants only contain an accelerometer
and the BMI055 actually is a accelerometer + gyroscope combo.
Clarify this in the help text and also make the list of supported
variants complete and sorted for consistency.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210611080903.14384-3-stephan@gerhold.net
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
According to sysfs-bus-iio documentation the unit for accelerometer
values after applying scale/offset should be m/s^2, not g, which explains
why the scale values for the other variants in bmc150-accel do not match
exactly the values given in the datasheet.
To get the correct values, we need to multiply the BMA222 scale values
by g = 9.80665 m/s^2.
Fixes: a1a210bf29 ("iio: accel: bmc150-accel: Add support for BMA222")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210611080903.14384-2-stephan@gerhold.net
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Gcc reports build error when CONFIG_IIO_TRIGGERED_BUFFER is not set:
riscv64-linux-gnu-ld: drivers/iio/dummy/iio_simple_dummy_buffer.o: in function `iio_simple_dummy_configure_buffer':
iio_simple_dummy_buffer.c:(.text+0x2b0): undefined reference to `iio_triggered_buffer_setup_ext'
riscv64-linux-gnu-ld: drivers/iio/dummy/iio_simple_dummy_buffer.o: in function `.L0 ':
iio_simple_dummy_buffer.c:(.text+0x2fc): undefined reference to `iio_triggered_buffer_cleanup'
Fix it by select IIO_TRIGGERED_BUFFER for config IIO_SIMPLE_DUMMY_BUFFER.
Fixes: 738f6ba118 ("iio: dummy: iio_simple_dummy_buffer: use triggered buffer core calls")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These were usually used before the conversion to devm_ functions, so that
the remove hook would be able to retrieve the pointer and do cleanups on
remove.
When the conversion happened, they should have been removed, but were
omitted.
Some drivers were copied from drivers that fit the criteria described
above. In any case, in order to prevent more drivers from being used as
example (and have spi_set_drvdata() needlessly set), this change removes it
from the IIO ADC group.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513111035.77950-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These were usually used before the conversion to devm_ functions, so that
the remove hook would be able to retrieve the pointer and do cleanups on
remove.
When the conversion happened, they should have been removed, but were
omitted.
Some drivers were copied from drivers that fit the criteria described
above. In any case, in order to prevent more drivers from being used as
example (and have spi_set_drvdata() needlessly set), this change removes it
from the IIO IMU group.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513122512.93187-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since all AD Sigma-Delta drivers now use the
devm_ad_sd_setup_buffer_and_trigger() function, we can remove the old
ad_sd_{setup,cleanup}_buffer_and_trigger() functions.
This way we can discourage new drivers that use the ad_sigma_delta
lib-driver to use these (older functions).
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513120752.90074-13-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The devm_clk_get_optional() helper returns NULL when devm_clk_get() returns
-ENOENT.
This makes things slightly cleaner. The added benefit is mostly cosmetic.
Also, a minor detail with this call, is that the reference for the parent
device is taken as `spi->dev` instead of `&st->sd.spi->dev` (which looks a
little quirky).
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513120752.90074-10-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
With the devm_ad_sd_setup_buffer_and_trigger() helper, it's a bit easier
now to convert the probe of the AD7780 driver to use device-managed
functions.
Only the regulator disable requires a devm_add_action_or_reset() callback.
This change does that, cleaning up the driver a bit.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513120752.90074-9-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
With the devm_ad_sd_setup_buffer_and_trigger() helper, it's a bit easier
now to convert the probe of the AD7791 driver to use device-managed
functions.
Only the regulator disable requires a devm_add_action_or_reset() callback.
This change does that, cleaning up the driver a bit.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513120752.90074-8-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
With the devm_ad_sd_setup_buffer_and_trigger() helper, it's a bit easier
now to convert the probe of the AD7793 driver to use device-managed
functions.
Only the regulator disable requires a devm_add_action_or_reset() callback.
This change does that, cleaning up the driver a bit.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513120752.90074-7-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This is a version of ad_sd_setup_buffer_and_trigger() with all underlying
functions (that are used) being replaced with their device-managed
variants.
One thing to take care here is with {devm_}iio_trigger_alloc(), where both
functions take a parent-device object as the first parameter.
To make sure nothing quirky is happening, the devm_ad_sd_probe_trigger()
function is checking that the provided 'dev' reference is the same as the
one stored on the 'struct ad_sigma_delta' driver data.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513120752.90074-6-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Some Yoga laptops with 1 accelerometer in the display and 1 in the base,
use an ACPI HID of DUAL250E instead of BOSC0200.
Set the iio-device's label for DUAL250E devices to a value indicating which
sensor is which, mirroring how we do this for BOSC0200 dual sensor devices.
Note the DUAL250E fwnode unfortunately does not include a mount-matrix.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210523170103.176958-10-hdegoede@redhat.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Some 360 degree hinges (yoga) style 2-in-1 devices use 2 bmc150 accels
to allow the OS to determine the angle between the display and the base
of the device, so that the OS can determine if the 2-in-1 is in laptop
or in tablet-mode.
On Windows both accelerometers are read (polled) by a special service
and this service calls the DSM (Device Specific Method), which in turn
translates the angles to one of laptop/tablet/tent/stand mode and then
notifies the EC about the new mode and the EC then enables or disables
the builtin keyboard and touchpad based in the mode.
When the 2-in-1 is powered-on or resumed folded in tablet mode the
EC senses this independent of the DSM by using a HALL effect sensor
which senses that the keyboard has been folded away behind the display.
At power-on or resume the EC disables the keyboard based on this and
the only way to get the keyboard to work after this is to call the
DSM to re-enable it.
Call the DSM on probe() and resume() to fix the keyboard not working
when powered-on / resumed in tablet-mode.
This patch was developed and tested on a Lenovo Yoga 300-IBR.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210523170103.176958-8-hdegoede@redhat.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Now that the definition of the bmc150_accel_data struct is no longer
private to bmc150-accel-core.c, bmc150-accel-i2c.c can simply directly
access the second_dev member and the accessor functions are no longer
necessary.
Note if the i2c_acpi_new_device() for the second-client now fails,
an ERR_PTR gets stored in data->second_dev this is fine since it is only
ever passed to i2c_unregister_device() which has an IS_ERR_OR_NULL() check.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210523170103.176958-7-hdegoede@redhat.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
On machines with dual accelerometers described in a single ACPI fwnode,
the bmc150_accel_probe() instantiates a second i2c-client for the second
accelerometer.
A pointer to this manually instantiated second i2c-client is stored
inside the iio_dev's private-data through bmc150_set_second_device(),
so that the i2c-client can be unregistered from bmc150_accel_remove().
Before this commit bmc150_set_second_device() took only 1 argument so it
would store the pointer in private-data of the iio_dev belonging to the
manually instantiated i2c-client, leading to the bmc150_accel_remove()
call for the second_dev trying to unregister *itself* while it was
being removed, leading to a deadlock and rmmod hanging.
Change bmc150_set_second_device() to take 2 arguments: 1. The i2c-client
which is instantiating the second i2c-client for the 2nd accelerometer and
2. The second-device pointer itself (which also is an i2c-client).
This will store the second_device pointer in the private data of the
iio_dev belonging to the (ACPI instantiated) i2c-client for the first
accelerometer and will make bmc150_accel_remove() unregister the
second_device i2c-client when called for the first client,
avoiding the deadlock.
Fixes: 5bfb3a4bd8 ("iio: accel: bmc150: Check for a second ACPI device for BOSC0200")
Cc: Jeremy Cline <jeremy@jcline.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The drvdata for iio-parent devices points to the struct iio_dev for
the iio-device. So by directly casting the return from i2c_get_clientdata()
to struct bmc150_accel_data * the code was ending up storing the second_dev
pointer in (and retrieving it from) some semi-random offset inside
struct iio_dev, rather then storing it in the second_dev member of the
bmc150_accel_data struct.
Fix the code to get the struct bmc150_accel_data * pointer to call
iio_priv() on the struct iio_dev * returned by i2c_get_clientdata(),
so that the correct pointer gets dereferenced.
This fixes the following oops on rmmod, caused by trying to
dereference the wrong return of bmc150_get_second_device():
[ 238.980737] BUG: unable to handle page fault for address: 0000000000004710
[ 238.980755] #PF: supervisor read access in kernel mode
[ 238.980760] #PF: error_code(0x0000) - not-present page
...
[ 238.980841] i2c_unregister_device.part.0+0x19/0x60
[ 238.980856] 0xffffffffc0815016
[ 238.980863] i2c_device_remove+0x25/0xb0
[ 238.980869] __device_release_driver+0x180/0x240
[ 238.980876] driver_detach+0xd4/0x120
[ 238.980882] bus_remove_driver+0x5b/0xd0
[ 238.980888] i2c_del_driver+0x44/0x70
While at it also remove the now no longer sensible checks for data
being NULL, iio_priv never returns NULL for an iio_dev with non 0
sized private-data.
Fixes: 5bfb3a4bd8 ("iio: accel: bmc150: Check for a second ACPI device for BOSC0200")
Cc: Jeremy Cline <jeremy@jcline.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since:
commit cbacb5ab0a ("docs: printk-formats: Stop encouraging use of
unnecessary %h[xudi] and %hh[xudi]")
use of these format strings has been discouraged.
As there are only a few such instances in IIO, this is part of a
series clearing them out so they don't get copied into new drivers.
Use the 0x02x form as the length specifier when used with # includes
the 0x prefix and is very unlikely to be what was intended by the author.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20210603180612.3635250-5-jic23@kernel.org
Since:
commit cbacb5ab0a ("docs: printk-formats: Stop encouraging use of
unnecessary %h[xudi] and %hh[xudi]")
use of these format strings has been discouraged.
Use the 0x02x form as the length specifier when used with # includes
the 0x prefix and is very unlikely to be what was intended by the author.
Part of a series removing all uses from IIO in the interestings of
avoiding providing bad examples for people to copy.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20210603180612.3635250-4-jic23@kernel.org
Since:
commit cbacb5ab0a ("docs: printk-formats: Stop encouraging use of
unnecessary %h[xudi] and %hh[xudi]")
use of these format strings has been discouraged.
Use the 0x02x form as the length specifier when used with # includes
the 0x prefix and is very unlikely to be what was intended by the author.
As there are not that many in IIO, this is part of an effort to clear
them out so we don't have any instances that might get copied into
new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Maxime Roussin-Bélanger <maxime.roussinbelanger@gmail.com>
Cc: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20210603180612.3635250-3-jic23@kernel.org
clang complains about multiple instances of printing an integer
using the %hhx format string:
drivers/iio/light/si1133.c:982:4: error: format specifies type 'unsigned char' but the argument has type 'unsigned int' [-Werror,-Wformat]
part_id, rev_id, mfr_id);
^~~~~~~
Print them as a normal integer instead, leaving the "#02"
length modifier.
Use the 0x02x form as the length specifier when used with # includes
the 0x prefix and is very unlikely to be what was intended by the author.
Fixes: e01e7eaf37 ("iio: light: introduce si1133")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20210603180612.3635250-2-jic23@kernel.org
