Some observations about the plane registers:
- the control register will self-arm if the plane is not already
enabled, thus we want to write it as close to (or ideally after)
the surface register
- tileoff/linoff/offset/aux_offset are self-arming as well so we want
them close to the surface register as well
- color keying registers we maybe self arming before SKL. Not 100%
sure but we can try to keep them near to the surface register
as well
- chv pipe b csc register are double buffered but self arming so
moving them down a bit
- the rest should be mostly armed by the surface register so we can
safely write them first, and to just for some consistency let's try
to follow keep them in order based on the register offset
None of this will have any effect of course unless the vblank evasion
fails (which it still does sometimes). Another potential future benefit
might be pulling the non-self armings registers outside the vblank
evasion since they won't latch until the arming register has been
written. This would make the critical section a bit lighter and thus
less likely to exceed the deadline.
v2: Rebase due to input CSC
v3: Swap LINOFF/TILEOFF and KEYMSK/KEYMAX to actually follow
the last rule above (Matt)
Add a bit more rationale to the commit message (Matt)
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114210729.16185-2-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
According to Display Stream compression spec 1.2, the picture
parameter set metadata is sent from source to sink device
using the DP Secondary data packet. An infoframe is formed
for the PPS SDP header and PPS SDP payload bytes.
This patch adds helpers to fill the PPS SDP header
and PPS SDP payload according to the DSC 1.2 specification.
v7:
* Use BUILD_BUG_ON() to protect changing struct size (Ville)
* Remove typecaseting (Ville)
* Include byteorder.h in drm_dsc.c (Ville)
* Correct kernel doc spacing (Anusha)
v6:
* Use proper sequence points for breaking down the
assignments (Chris Wilson)
* Use SPDX identifier
v5:
Do not use bitfields for DRM structs (Jani N)
v4:
* Use DSC constants for params that dont change across
configurations
v3:
* Add reference to added kernel-docs in
Documentation/gpu/drm-kms-helpers.rst (Daniel Vetter)
v2:
* Add EXPORT_SYMBOL for the drm functions (Manasi)
Cc: dri-devel@lists.freedesktop.org
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Acked-by: Sean Paul <seanpaul@chromium.org> (For merging through
drm-intel)
Link: https://patchwork.freedesktop.org/patch/msgid/20181127214125.17658-5-manasi.d.navare@intel.com
Currently, we convert the error state into a string every time we read
from sysfs (and sysfs reads in page size (4KiB) chunks). We do try to
window the string and only capture the portion that is being read, but
that means that we must always convert up to the window to find the
start. For a very large error state bordering on EXEC_OBJECT_CAPTURE
abuse, this is noticeable as it degrades to O(N^2)!
As we do not have a convenient hook for sysfs open(), and we would like
to keep the lazy conversion into a string, do the conversion of the
whole string on the first read and keep the string until the error state
is freed.
v2: Don't double advance simple_read_from_buffer
v3: Due to extreme pain of lack of vrealloc, use a scatterlist
v4: Keep the forward iterator loosely cached
v5: Stylistic improvements to reduce patch size
Reported-by: Jason Ekstrand <jason@jlekstrand.net>
Testcase: igt/gem_exec_capture/many*
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123132325.26541-1-chris@chris-wilson.co.uk
If a PSR error happened and the driver is reloaded, the EDP_PSR_IIR
will still keep the error set even after the reset done in the
irq_preinstall and irq_uninstall hooks.
And enabling in this situation cause the screen to freeze in the
first time that PSR HW tries to activate so lets keep PSR disabled
to avoid any rendering problems.
v5: rebased: using edp_psr_shift()
v4: Moved handling from intel_psr_compute_config() to
intel_psr_init() to avoid hardware access during compute(Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
squash
Link: https://patchwork.freedesktop.org/patch/msgid/20181121225441.18785-5-jose.souza@intel.com
While PSR is active hardware will do aux transactions by it self to
wakeup sink to receive a new frame when necessary. If that
transaction is not acked by sink, hardware will trigger this
interruption.
So let's disable PSR as it is a hint that there is problem with this
sink.
The removed FIXME was asking to manually train the link but we don't
need to do that as by spec sink should do a short pulse when it is
out of sync with source, we just need to make sure it is awaken and
the SDP header with PSR inactive set it will trigger the short pulse
with a error set in the link status.
v3: added workarround to fix scheduled work starvation cause by
to frequent PSR error interruption
v4: only setting irq_aux_error as we don't care in clear it and
not using dev_priv->irq_lock as consequence.
v5: rebased: using edp_psr_shift()
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181121225441.18785-4-jose.souza@intel.com
When a PSR error happens sink sets the PSR error register and also
set the link status to a error status.
So in the short pulse handling it was returning earlier and doing a
full detection and attempting to retrain but it fails as PSR HW is
in change of the main-link.
Just call intel_psr_short_pulse() before
intel_dp_needs_link_retrain() is not the right fix as
intel_dp_needs_link_retrain() would return true and trigger a full
detection while PSR HW is still in change of main-link.
Check for PSR active is also not safe as it could be inactive due a
frontbuffer invalidate and still doing the PSR exit sequence.
v3: added comment in intel_dp_needs_link_retrain()
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181121225441.18785-2-jose.souza@intel.com
Some eDP panels do not set a valid sink count value and even for the
ones that sets is should always be one for eDP, that is why it is not
cached in intel_edp_init_dpcd().
But intel_dp_short_pulse() compares the old count with the read one
if there is a mistmatch a full port detection will be executed, what
was happening in the first short pulse interruption of eDP panels
that sets sink count.
Instead of just skip the compasison for eDP panels, lets not read
the sink count at all for eDP.
v2: the previous version of this patch it was caching the sink count
in intel_edp_init_dpcd() but I was pointed out by Ville a patch that
handled a case of a eDP panel that do not set sink count and as sink
count is not used to eDP certification was choosed to just not read
it at all.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181121225441.18785-1-jose.souza@intel.com
While trying to add a chamelium test for short HPD IRQs, I ran into
issues where a hotplug storm would be triggered, but the point at which
it would be reported by the kernel would be after igt actually finished
checking i915_hpd_storm_ctl's status. So, fix this by simply
synchronizing our IRQ work, dig_port_work, and hotplug_work before
printing out the HPD storm status in i915_hpd_storm_ctl_show().
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181121003718.17704-1-lyude@redhat.com
If we force a plane update to fix up our half populated plane state
we'll also force on the pipe gamma for the plane (since we always
enable pipe gamma currently). If the BIOS hasn't programmed a sensible
LUT into the hardware this will cause the image to become corrupted.
Typical symptoms are a purple/yellow/etc. flash when the driver loads.
To avoid this let's program something sensible into the LUT when
we do the plane update. In the future I plan to add proper plane
gamma enable readout so this is just a temporary measure.
Cc: Hans de Goede <hdegoede@redhat.com>
Fixes: 516a49cc19 ("drm/i915: Fix assert_plane() warning on bootup with external display")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181120135450.3634-1-ville.syrjala@linux.intel.com
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Depending on the transcoder enum values to translate from transcoder to
the corresponding CHICKEN_TRANS register can easily break if we add a
new transcoder. Add an explicit mapping instead, by using helpers to
look up the register instance either by transcoder or port (since
unconveniently the registers have both port and transcoder specific
bits).
While at it also check for the correctness of GEN, port, transcoder. I
wasn't sure if psr2_enabled can only be set for GEN9+, but that seems to
be the case indeed (see setting of sink_psr2_support in
intel_psr_init_dpcd()).
v2 (Ville):
- Make gen9_chicken_trans_reg() internal to intel_psr.c.
- s/trans/cpu_transcoder/
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181119180021.370-1-imre.deak@intel.com
Under moderate amounts of GPU stress, we can observe on Bearlake and
Pineview (later gen3 models) that we execute the following batch buffer
before the write into the batch is coherent. Adding extra (tested with
upto 32x) MI_FLUSH to either the invalidation, flush or both phases does
not solve the incoherency issue with the relocations, but emitting the
MI_STORE_DWORD_IMM twice does. So be it.
Fixes: 7dd4f6729f ("drm/i915: Async GPU relocation processing")
Testcase: igt/gem_tiled_fence_blits # blb/pnv
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181119154153.15327-1-chris@chris-wilson.co.uk
New features for 4.21:
amdgpu:
- Support for SDMA paging queue on vega
- Put compute EOP buffers into vram for better performance
- Share more code with amdkfd
- Support for scanout with DCC on gfx9
- Initial kerneldoc for DC
- Updated SMU firmware support for gfx8 chips
- Rework CSA handling for eventual support for preemption
- XGMI PSP support
- Clean up RLC handling
- Enable GPU reset by default on VI, SOC15 dGPUs
- Ring and IB test cleanups
amdkfd:
- Share more code with amdgpu
ttm:
- Move global init out of the drivers
scheduler:
- Track if schedulers are ready for work
- Timeout/fault handling changes to facilitate GPU recovery
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114165113.3751-1-alexander.deucher@amd.com
drm-misc-next for v4.21, part 1:
UAPI Changes:
- Add syncobj timeline support to drm.
Cross-subsystem Changes:
- Remove shared fence staging in dma-buf's fence object, and allow
reserving more than 1 fence and add more paranoia when debugging.
- Constify infoframe functions in video/hdmi.
Core Changes:
- Add vkms todo, and a lot of assorted doc fixes.
- Drop transitional helpers and convert drivers to use drm_atomic_helper_shutdown().
- Move atomic state helper functions to drm_atomic_state_helper.[ch]
- Refactor drm selftests, and add new tests.
- DP MST atomic state cleanups.
- Drop EXPORT_SYMBOL from drm leases.
- Lease cleanups and fixes.
- Create render node for vgem.
Driver Changes:
- Fix build failure in imx without fbdev emulation.
- Add rotation quirk for GPD win2 panel.
- Add support for various CDTech panels, Banana Pi Panel, DLC1010GIG,
Olimex LCD-O-LinuXino, Samsung S6D16D0, Truly NT35597 WQXGA,
Himax HX8357D, simulated RTSM AEMv8.
- Add dw_hdmi support to rockchip driver.
- Fix YUV support in vc4.
- Fix resource id handling in virtio.
- Make rockchip use dw-mipi-dsi bridge driver, and add dual dsi support.
- Advertise that tinydrm only supports DRM_FORMAT_MOD_LINEAR.
- Convert many drivers to use atomic helpers, and drm_fbdev_generic_setup().
- Add Mali linear tiled formats, and enable them in the Mali-DP driver.
- Add support for H6 DE3 mixer 0, DW HDMI, HDMI PHY and TCON TOP.
- Assorted driver cleanups and fixes.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/be7ebd91-edd9-8fa4-4286-1c57e3165113@linux.intel.com
