The module parameter qcaspi_pluggable controls if QCA7000 signature
should be checked at driver probe (current default) or not. Unfortunately
this could fail in case the chip is temporary in reset, which isn't under
total control by the Linux host. So disable this check per default
in order to avoid unexpected probe failures.
Fixes: 291ab06ecf ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://patch.msgid.link/20241206184643.123399-3-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Storing the maximum clock speed in module parameter qcaspi_clkspeed
has the unintended side effect that the first probed instance
defines the value for all other instances. Fix this issue by storing
it in max_speed_hz of the relevant SPI device.
This fix keeps the priority of the speed parameter (module parameter,
device tree property, driver default). Btw this uses the opportunity
to get the rid of the unused member clkspeed.
Fixes: 291ab06ecf ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://patch.msgid.link/20241206184643.123399-2-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
t4_set_vf_mac_acl() uses pf to set mac addr, but t4vf_get_vf_mac_acl()
uses port number to get mac addr, this leads to error when an attempt
to set MAC address on VF's of PF2 and PF3.
This patch fixes the issue by using port number to set mac address.
Fixes: e0cdac65ba ("cxgb4vf: configure ports accessible by the VF")
Signed-off-by: Anumula Murali Mohan Reddy <anumula@chelsio.com>
Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241206062014.49414-1-anumula@chelsio.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On port initialization, we configure the maximum frame length accepted
by the receive module associated with the port. This value is currently
written to the MAX_LEN field of the DEV10G_MAC_ENA_CFG register, when in
fact, it should be written to the DEV10G_MAC_MAXLEN_CFG register. Fix
this.
Fixes: 946e7fd505 ("net: sparx5: add port module support")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing port mirroring, the physical port to send the frame to, is
written to the FRMC_PORT_VAL field of the QFWD_FRAME_COPY_CFG register.
This field is 7 bits wide on sparx5 and 6 bits wide on lan969x, and has
a default value of 65 and 30, respectively (the number of front ports).
On mirror deletion, we set the default value of the monitor port to
65 for this field, in case no more ports exists for the mirror. Needless
to say, this will not fit the 6 bits on lan969x.
Fix this by correctly using the n_ports constant instead.
Fixes: 3f9e46347a ("net: sparx5: use SPX5_CONST for constants which already have a symbol")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FDMA handler is responsible for scheduling a NAPI poll, which will
eventually fetch RX packets from the FDMA queue. Currently, the FDMA
handler is run in a threaded context. For some reason, this kills
performance. Admittedly, I did not do a thorough investigation to see
exactly what causes the issue, however, I noticed that in the other
driver utilizing the same FDMA engine, we run the FDMA handler in hard
IRQ context.
Fix this performance issue, by running the FDMA handler in hard IRQ
context, not deferring any work to a thread.
Prior to this change, the RX UDP performance was:
Interval Transfer Bitrate Jitter
0.00-10.20 sec 44.6 MBytes 36.7 Mbits/sec 0.027 ms
After this change, the rx UDP performance is:
Interval Transfer Bitrate Jitter
0.00-9.12 sec 1.01 GBytes 953 Mbits/sec 0.020 ms
Fixes: 10615907e9 ("net: sparx5: switchdev: adding frame DMA functionality")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depmod reports a cyclic dependency between modules sparx5-switch.ko and
lan969x-switch.ko:
depmod: ERROR: Cycle detected: lan969x_switch -> sparx5_switch -> lan969x_switch
depmod: ERROR: Found 2 modules in dependency cycles!
make[2]: *** [scripts/Makefile.modinst:132: depmod] Error 1
make: *** [Makefile:224: __sub-make] Error 2
This makes sense, as they both require symbols from each other.
Fix this by compiling lan969x support into the sparx5-switch.ko module.
In order to do this, in a sensible way, we move the lan969x/ dir into
the sparx5/ dir and do some code cleanup of code that is no longer
required.
After this patch, depmod will no longer complain, as lan969x support is
compiled into the sparx5-swicth.ko module, and can no longer be compiled
as a standalone module.
Fixes: 98a0111960 ("net: sparx5: add compatible string for lan969x")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean says:
====================
Ocelot PTP fixes
This is another attempt at "net: mscc: ocelot: be resilient to loss of
PTP packets during transmission".
https://lore.kernel.org/netdev/20241203164755.16115-1-vladimir.oltean@nxp.com/
The central change is in patch 4/5. It recovers a port from a very
reproducible condition where previously, it would become unable to take
any hardware TX timestamp.
Then we have patches 1/5 and 5/5 which are extra bug fixes.
Patches 2/5 and 3/5 are logical changes split out of the monolithic
patch previously submitted as v1, so that patch 4/5 is hopefully easier
to follow.
====================
Link: https://patch.msgid.link/20241205145519.1236778-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
An unsupported RX filter will leave the port with TX timestamping still
applied as per the new request, rather than the old setting. When
parsing the tx_type, don't apply it just yet, but delay that until after
we've parsed the rx_filter as well (and potentially returned -ERANGE for
that).
Similarly, copy_to_user() may fail, which is a rare occurrence, but
should still be treated by unwinding what was done.
Fixes: 96ca08c058 ("net: mscc: ocelot: set up traps for PTP packets")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241205145519.1236778-6-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Felix DSA driver presents unique challenges that make the simplistic
ocelot PTP TX timestamping procedure unreliable: any transmitted packet
may be lost in hardware before it ever leaves our local system.
This may happen because there is congestion on the DSA conduit, the
switch CPU port or even user port (Qdiscs like taprio may delay packets
indefinitely by design).
The technical problem is that the kernel, i.e. ocelot_port_add_txtstamp_skb(),
runs out of timestamp IDs eventually, because it never detects that
packets are lost, and keeps the IDs of the lost packets on hold
indefinitely. The manifestation of the issue once the entire timestamp
ID range becomes busy looks like this in dmesg:
mscc_felix 0000:00:00.5: port 0 delivering skb without TX timestamp
mscc_felix 0000:00:00.5: port 1 delivering skb without TX timestamp
At the surface level, we need a timeout timer so that the kernel knows a
timestamp ID is available again. But there is a deeper problem with the
implementation, which is the monotonically increasing ocelot_port->ts_id.
In the presence of packet loss, it will be impossible to detect that and
reuse one of the holes created in the range of free timestamp IDs.
What we actually need is a bitmap of 63 timestamp IDs tracking which one
is available. That is able to use up holes caused by packet loss, but
also gives us a unique opportunity to not implement an actual timer_list
for the timeout timer (very complicated in terms of locking).
We could only declare a timestamp ID stale on demand (lazily), aka when
there's no other timestamp ID available. There are pros and cons to this
approach: the implementation is much more simple than per-packet timers
would be, but most of the stale packets would be quasi-leaked - not
really leaked, but blocked in driver memory, since this algorithm sees
no reason to free them.
An improved technique would be to check for stale timestamp IDs every
time we allocate a new one. Assuming a constant flux of PTP packets,
this avoids stale packets being blocked in memory, but of course,
packets lost at the end of the flux are still blocked until the flux
resumes (nobody left to kick them out).
Since implementing per-packet timers is way too complicated, this should
be good enough.
Testing procedure:
Persistently block traffic class 5 and try to run PTP on it:
$ tc qdisc replace dev swp3 parent root taprio num_tc 8 \
map 0 1 2 3 4 5 6 7 queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \
base-time 0 sched-entry S 0xdf 100000 flags 0x2
[ 126.948141] mscc_felix 0000:00:00.5: port 3 tc 5 min gate length 0 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 1 octets including FCS
$ ptp4l -i swp3 -2 -P -m --socket_priority 5 --fault_reset_interval ASAP --logSyncInterval -3
ptp4l[70.351]: port 1 (swp3): INITIALIZING to LISTENING on INIT_COMPLETE
ptp4l[70.354]: port 0 (/var/run/ptp4l): INITIALIZING to LISTENING on INIT_COMPLETE
ptp4l[70.358]: port 0 (/var/run/ptp4lro): INITIALIZING to LISTENING on INIT_COMPLETE
[ 70.394583] mscc_felix 0000:00:00.5: port 3 timestamp id 0
ptp4l[70.406]: timed out while polling for tx timestamp
ptp4l[70.406]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[70.406]: port 1 (swp3): send peer delay response failed
ptp4l[70.407]: port 1 (swp3): clearing fault immediately
ptp4l[70.952]: port 1 (swp3): new foreign master d858d7.fffe.00ca6d-1
[ 71.394858] mscc_felix 0000:00:00.5: port 3 timestamp id 1
ptp4l[71.400]: timed out while polling for tx timestamp
ptp4l[71.400]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[71.401]: port 1 (swp3): send peer delay response failed
ptp4l[71.401]: port 1 (swp3): clearing fault immediately
[ 72.393616] mscc_felix 0000:00:00.5: port 3 timestamp id 2
ptp4l[72.401]: timed out while polling for tx timestamp
ptp4l[72.402]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[72.402]: port 1 (swp3): send peer delay response failed
ptp4l[72.402]: port 1 (swp3): clearing fault immediately
ptp4l[72.952]: port 1 (swp3): new foreign master d858d7.fffe.00ca6d-1
[ 73.395291] mscc_felix 0000:00:00.5: port 3 timestamp id 3
ptp4l[73.400]: timed out while polling for tx timestamp
ptp4l[73.400]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[73.400]: port 1 (swp3): send peer delay response failed
ptp4l[73.400]: port 1 (swp3): clearing fault immediately
[ 74.394282] mscc_felix 0000:00:00.5: port 3 timestamp id 4
ptp4l[74.400]: timed out while polling for tx timestamp
ptp4l[74.401]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[74.401]: port 1 (swp3): send peer delay response failed
ptp4l[74.401]: port 1 (swp3): clearing fault immediately
ptp4l[74.953]: port 1 (swp3): new foreign master d858d7.fffe.00ca6d-1
[ 75.396830] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 0 which seems lost
[ 75.405760] mscc_felix 0000:00:00.5: port 3 timestamp id 0
ptp4l[75.410]: timed out while polling for tx timestamp
ptp4l[75.411]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[75.411]: port 1 (swp3): send peer delay response failed
ptp4l[75.411]: port 1 (swp3): clearing fault immediately
(...)
Remove the blocking condition and see that the port recovers:
$ same tc command as above, but use "sched-entry S 0xff" instead
$ same ptp4l command as above
ptp4l[99.489]: port 1 (swp3): INITIALIZING to LISTENING on INIT_COMPLETE
ptp4l[99.490]: port 0 (/var/run/ptp4l): INITIALIZING to LISTENING on INIT_COMPLETE
ptp4l[99.492]: port 0 (/var/run/ptp4lro): INITIALIZING to LISTENING on INIT_COMPLETE
[ 100.403768] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 0 which seems lost
[ 100.412545] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 1 which seems lost
[ 100.421283] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 2 which seems lost
[ 100.430015] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 3 which seems lost
[ 100.438744] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 4 which seems lost
[ 100.447470] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 100.505919] mscc_felix 0000:00:00.5: port 3 timestamp id 0
ptp4l[100.963]: port 1 (swp3): new foreign master d858d7.fffe.00ca6d-1
[ 101.405077] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 101.507953] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 102.405405] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 102.509391] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 103.406003] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 103.510011] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 104.405601] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 104.510624] mscc_felix 0000:00:00.5: port 3 timestamp id 0
ptp4l[104.965]: selected best master clock d858d7.fffe.00ca6d
ptp4l[104.966]: port 1 (swp3): assuming the grand master role
ptp4l[104.967]: port 1 (swp3): LISTENING to GRAND_MASTER on RS_GRAND_MASTER
[ 105.106201] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.232420] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.359001] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.405500] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.485356] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.511220] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.610938] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.737237] mscc_felix 0000:00:00.5: port 3 timestamp id 0
(...)
Notice that in this new usage pattern, a non-congested port should
basically use timestamp ID 0 all the time, progressing to higher numbers
only if there are unacknowledged timestamps in flight. Compare this to
the old usage, where the timestamp ID used to monotonically increase
modulo OCELOT_MAX_PTP_ID.
In terms of implementation, this simplifies the bookkeeping of the
ocelot_port :: ts_id and ptp_skbs_in_flight. Since we need to traverse
the list of two-step timestampable skbs for each new packet anyway, the
information can already be computed and does not need to be stored.
Also, ocelot_port->tx_skbs is always accessed under the switch-wide
ocelot->ts_id_lock IRQ-unsafe spinlock, so we don't need the skb queue's
lock and can use the unlocked primitives safely.
This problem was actually detected using the tc-taprio offload, and is
causing trouble in TSN scenarios, which Felix (NXP LS1028A / VSC9959)
supports but Ocelot (VSC7514) does not. Thus, I've selected the commit
to blame as the one adding initial timestamping support for the Felix
switch.
Fixes: c0bcf53766 ("net: dsa: ocelot: add hardware timestamping support for Felix")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241205145519.1236778-5-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ocelot_get_txtstamp() is a threaded IRQ handler, requested explicitly as
such by both ocelot_ptp_rdy_irq_handler() and vsc9959_irq_handler().
As such, it runs with IRQs enabled, and not in hardirq context. Thus,
ocelot_port_add_txtstamp_skb() has no reason to turn off IRQs, it cannot
be preempted by ocelot_get_txtstamp(). For the same reason,
dev_kfree_skb_any_reason() will always evaluate as kfree_skb_reason() in
this calling context, so just simplify the dev_kfree_skb_any() call to
kfree_skb().
Also, ocelot_port_txtstamp_request() runs from NET_TX softirq context,
not with hardirqs enabled. Thus, ocelot_get_txtstamp() which shares the
ocelot_port->tx_skbs.lock lock with it, has no reason to disable hardirqs.
This is part of a larger rework of the TX timestamping procedure.
A logical subportion of the rework has been split into a separate
change.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241205145519.1236778-4-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This condition, theoretically impossible to trigger, is not really
handled well. By "continuing", we are skipping the write to SYS_PTP_NXT
which advances the timestamp FIFO to the next entry. So we are reading
the same FIFO entry all over again, printing stack traces and eventually
killing the kernel.
No real problem has been observed here. This is part of a larger rework
of the timestamp IRQ procedure, with this logical change split out into
a patch of its own. We will need to "goto next_ts" for other conditions
as well.
Fixes: 9fde506e0c ("net: mscc: ocelot: warn when a PTP IRQ is raised for an unknown skb")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241205145519.1236778-3-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 66600fac7a ("net: stmmac: TSO: Fix unbalanced DMA map/unmap
for non-paged SKB data") moved the assignment of tx_skbuff_dma[]'s
members to be later in stmmac_tso_xmit().
The buf (dma cookie) and len stored in this structure are passed to
dma_unmap_single() by stmmac_tx_clean(). The DMA API requires that
the dma cookie passed to dma_unmap_single() is the same as the value
returned from dma_map_single(). However, by moving the assignment
later, this is not the case when priv->dma_cap.addr64 > 32 as "des"
is offset by proto_hdr_len.
This causes problems such as:
dwc-eth-dwmac 2490000.ethernet eth0: Tx DMA map failed
and with DMA_API_DEBUG enabled:
DMA-API: dwc-eth-dwmac 2490000.ethernet: device driver tries to +free DMA memory it has not allocated [device address=0x000000ffffcf65c0] [size=66 bytes]
Fix this by maintaining "des" as the original DMA cookie, and use
tso_des to pass the offset DMA cookie to stmmac_tso_allocator().
Full details of the crashes can be found at:
https://lore.kernel.org/all/d8112193-0386-4e14-b516-37c2d838171a@nvidia.com/https://lore.kernel.org/all/klkzp5yn5kq5efgtrow6wbvnc46bcqfxs65nz3qy77ujr5turc@bwwhelz2l4dw/
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Reported-by: Thierry Reding <thierry.reding@gmail.com>
Fixes: 66600fac7a ("net: stmmac: TSO: Fix unbalanced DMA map/unmap for non-paged SKB data")
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Furong Xu <0x1207@gmail.com>
Link: https://patch.msgid.link/E1tJXcx-006N4Z-PC@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Michael Chan says:
====================
bnxt_en: Bug fixes
There are 2 bug fixes in this series. This first one fixes the issue
of setting the gso_type incorrectly for HW GRO packets on 5750X (Thor)
chips. This can cause HW GRO packets to be dropped by the stack if
they are re-segmented. The second one fixes a potential division by
zero crash when dumping FW log coredump.
====================
Link: https://patch.msgid.link/20241204215918.1692597-1-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The existing code is using RSS profile to determine IPV4/IPV6 GSO type
on all chips older than 5760X. This won't work on 5750X chips that may
be using modified RSS profiles. This commit from 2018 has updated the
driver to not use RSS profile for HW GRO packets on newer chips:
50f011b63d ("bnxt_en: Update RSS setup and GRO-HW logic according to the latest spec.")
However, a recent commit to add support for the newest 5760X chip broke
the logic. If the GRO packet needs to be re-segmented by the stack, the
wrong GSO type will cause the packet to be dropped.
Fix it to only use RSS profile to determine GSO type on the oldest
5730X/5740X chips which cannot use the new method and is safe to use the
RSS profiles.
Also fix the L3/L4 hash type for RX packets by not using the RSS
profile for the same reason. Use the ITYPE field in the RX completion
to determine L3/L4 hash types correctly.
Fixes: a7445d6980 ("bnxt_en: Add support for new RX and TPA_START completion types for P7")
Reviewed-by: Colin Winegarden <colin.winegarden@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20241204215918.1692597-2-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Petr Machata says:
====================
selftests: mlxsw: Add few fixes for sharedbuffer test
Danielle Ratson writes:
Currently, the sharedbuffer test fails sometimes because it is reading a
maximum occupancy that is larger than expected on some different cases.
This is happening because the test assumes that the packet it is sending
is the only packet being passed to the device.
In addition, some duplications on one hand, and redundant test cases on
the other hand, were found in the test.
Add egress filters on h1 and h2 that will guarantee that the packets in
the buffer are sent in the test, and remove the redundant test cases.
====================
Link: https://patch.msgid.link/cover.1733414773.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The dr_domain_add_vport_cap() function generally returns NULL on error
but sometimes we want it to return ERR_PTR(-EBUSY) so the caller can
retry. The problem here is that "ret" can be either -EBUSY or -ENOMEM
and if it's and -ENOMEM then the error pointer is propogated back and
eventually dereferenced in dr_ste_v0_build_src_gvmi_qpn_tag().
Fixes: 11a45def2e ("net/mlx5: DR, Add support for SF vports")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/07477254-e179-43e2-b1b3-3b9db4674195@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull networking fixes from Paolo Abeni:
"Including fixes from can and netfilter.
Current release - regressions:
- rtnetlink: fix double call of rtnl_link_get_net_ifla()
- tcp: populate XPS related fields of timewait sockets
- ethtool: fix access to uninitialized fields in set RXNFC command
- selinux: use sk_to_full_sk() in selinux_ip_output()
Current release - new code bugs:
- net: make napi_hash_lock irq safe
- eth:
- bnxt_en: support header page pool in queue API
- ice: fix NULL pointer dereference in switchdev
Previous releases - regressions:
- core: fix icmp host relookup triggering ip_rt_bug
- ipv6:
- avoid possible NULL deref in modify_prefix_route()
- release expired exception dst cached in socket
- smc: fix LGR and link use-after-free issue
- hsr: avoid potential out-of-bound access in fill_frame_info()
- can: hi311x: fix potential use-after-free
- eth: ice: fix VLAN pruning in switchdev mode
Previous releases - always broken:
- netfilter:
- ipset: hold module reference while requesting a module
- nft_inner: incorrect percpu area handling under softirq
- can: j1939: fix skb reference counting
- eth:
- mlxsw: use correct key block on Spectrum-4
- mlx5: fix memory leak in mlx5hws_definer_calc_layout"
* tag 'net-6.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (76 commits)
net :mana :Request a V2 response version for MANA_QUERY_GF_STAT
net: avoid potential UAF in default_operstate()
vsock/test: verify socket options after setting them
vsock/test: fix parameter types in SO_VM_SOCKETS_* calls
vsock/test: fix failures due to wrong SO_RCVLOWAT parameter
net/mlx5e: Remove workaround to avoid syndrome for internal port
net/mlx5e: SD, Use correct mdev to build channel param
net/mlx5: E-Switch, Fix switching to switchdev mode in MPV
net/mlx5: E-Switch, Fix switching to switchdev mode with IB device disabled
net/mlx5: HWS: Properly set bwc queue locks lock classes
net/mlx5: HWS: Fix memory leak in mlx5hws_definer_calc_layout
bnxt_en: handle tpa_info in queue API implementation
bnxt_en: refactor bnxt_alloc_rx_rings() to call bnxt_alloc_rx_agg_bmap()
bnxt_en: refactor tpa_info alloc/free into helpers
geneve: do not assume mac header is set in geneve_xmit_skb()
mlxsw: spectrum_acl_flex_keys: Use correct key block on Spectrum-4
ethtool: Fix wrong mod state in case of verbose and no_mask bitset
ipmr: tune the ipmr_can_free_table() checks.
netfilter: nft_set_hash: skip duplicated elements pending gc run
netfilter: ipset: Hold module reference while requesting a module
...
Pull tracing fixes from Steven Rostedt:
- Fix trace histogram sort function cmp_entries_dup()
The sort function cmp_entries_dup() returns either 1 or 0, and not -1
if parameter "a" is less than "b" by memcmp().
- Fix archs that call trace_hardirqs_off() without RCU watching
Both x86 and arm64 no longer call any tracepoints with RCU not
watching. It was assumed that it was safe to get rid of
trace_*_rcuidle() version of the tracepoint calls. This was needed to
get rid of the SRCU protection and be able to implement features like
faultable traceponits and add rust tracepoints.
Unfortunately, there were a few architectures that still relied on
that logic. There's only one file that has tracepoints that are
called without RCU watching. Add macro logic around the tracepoints
for architectures that do not have CONFIG_ARCH_WANTS_NO_INSTR defined
will check if the code is in the idle path (the only place RCU isn't
watching), and enable RCU around calling the tracepoint, but only do
it if the tracepoint is enabled.
* tag 'trace-v6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: Fix archs that still call tracepoints without RCU watching
tracing: Fix cmp_entries_dup() to respect sort() comparison rules
Pull HID fixes from Benjamin Tissoires:
- regression fix in suspend/resume for i2c-hid (Kenny Levinsen)
- fix wacom driver assuming a name can not be null (WangYuli)
- a couple of constify changes/fixes (Thomas Weißschuh)
- a couple of selftests/hid fixes (Maximilian Heyne & Benjamin
Tissoires)
* tag 'hid-for-linus-2024120501' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
selftests/hid: fix kfunc inclusions with newer bpftool
HID: bpf: drop unneeded casts discarding const
HID: bpf: constify hid_ops
selftests: hid: fix typo and exit code
HID: wacom: fix when get product name maybe null pointer
HID: i2c-hid: Revert to using power commands to wake on resume
Pull watchdog updates from Wim Van Sebroeck:
- Add support for exynosautov920 SoC
- Add support for Airoha EN7851 watchdog
- Add support for MT6735 TOPRGU/WDT
- Delete the cpu5wdt driver
- Always print when registering watchdog fails
- Several other small fixes and improvements
* tag 'linux-watchdog-6.13-rc1' of git://www.linux-watchdog.org/linux-watchdog: (36 commits)
watchdog: rti: of: honor timeout-sec property
watchdog: s3c2410_wdt: add support for exynosautov920 SoC
dt-bindings: watchdog: Document ExynosAutoV920 watchdog bindings
watchdog: mediatek: Add support for MT6735 TOPRGU/WDT
watchdog: mediatek: Make sure system reset gets asserted in mtk_wdt_restart()
dt-bindings: watchdog: fsl-imx-wdt: Add missing 'big-endian' property
dt-bindings: watchdog: Document Qualcomm QCS8300
docs: ABI: Fix spelling mistake in pretimeout_avaialable_governors
Revert "watchdog: s3c2410_wdt: use exynos_get_pmu_regmap_by_phandle() for PMU regs"
watchdog: rzg2l_wdt: Power on the watchdog domain in the restart handler
watchdog: Switch back to struct platform_driver::remove()
watchdog: it87_wdt: add PWRGD enable quirk for Qotom QCML04
watchdog: da9063: Remove __maybe_unused notations
watchdog: da9063: Do not use a global variable
watchdog: Delete the cpu5wdt driver
watchdog: Add support for Airoha EN7851 watchdog
dt-bindings: watchdog: airoha: document watchdog for Airoha EN7581
watchdog: sl28cpld_wdt: don't print out if registering watchdog fails
watchdog: rza_wdt: don't print out if registering watchdog fails
watchdog: rti_wdt: don't print out if registering watchdog fails
...
Tracepoints require having RCU "watching" as it uses RCU to do updates to
the tracepoints. There are some cases that would call a tracepoint when
RCU was not "watching". This was usually in the idle path where RCU has
"shutdown". For the few locations that had tracepoints without RCU
watching, there was an trace_*_rcuidle() variant that could be used. This
used SRCU for protection.
There are tracepoints that trace when interrupts and preemption are
enabled and disabled. In some architectures, these tracepoints are called
in a path where RCU is not watching. When x86 and arm64 removed these
locations, it was incorrectly assumed that it would be safe to remove the
trace_*_rcuidle() variant and also remove the SRCU logic, as it made the
code more complex and harder to implement new tracepoint features (like
faultable tracepoints and tracepoints in rust).
Instead of bringing back the trace_*_rcuidle(), as it will not be trivial
to do as new code has already been added depending on its removal, add a
workaround to the one file that still requires it (trace_preemptirq.c). If
the architecture does not define CONFIG_ARCH_WANTS_NO_INSTR, then check if
the code is in the idle path, and if so, call ct_irq_enter/exit() which
will enable RCU around the tracepoint.
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/20241204100414.4d3e06d0@gandalf.local.home
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: 48bcda6848 ("tracing: Remove definition of trace_*_rcuidle()")
Closes: https://lore.kernel.org/all/bddb02de-957a-4df5-8e77-829f55728ea2@roeck-us.net/
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Fix esoteric undefined behaviour due to uninitialized stack access
in ip_vs_protocol_init(), from Jinghao Jia.
2) Fix iptables xt_LED slab-out-of-bounds due to incorrect sanitization
of the led string identifier, reported by syzbot. Patch from
Dmitry Antipov.
3) Remove WARN_ON_ONCE reachable from userspace to check for the maximum
cgroup level, nft_socket cgroup matching is restricted to 255 levels,
but cgroups allow for INT_MAX levels by default. Reported by syzbot.
4) Fix nft_inner incorrect use of percpu area to store tunnel parser
context with softirqs, resulting in inconsistent inner header
offsets that could lead to bogus rule mismatches, reported by syzbot.
5) Grab module reference on ipset core while requesting set type modules,
otherwise kernel crash is possible by removing ipset core module,
patch from Phil Sutter.
6) Fix possible double-free in nft_hash garbage collector due to unstable
walk interator that can provide twice the same element. Use a sequence
number to skip expired/dead elements that have been already scheduled
for removal. Based on patch from Laurent Fasnach
netfilter pull request 24-12-05
* tag 'nf-24-12-05' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nft_set_hash: skip duplicated elements pending gc run
netfilter: ipset: Hold module reference while requesting a module
netfilter: nft_inner: incorrect percpu area handling under softirq
netfilter: nft_socket: remove WARN_ON_ONCE on maximum cgroup level
netfilter: x_tables: fix LED ID check in led_tg_check()
ipvs: fix UB due to uninitialized stack access in ip_vs_protocol_init()
====================
Link: https://patch.msgid.link/20241205002854.162490-1-pablo@netfilter.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Konstantin Shkolnyy says:
====================
vsock/test: fix wrong setsockopt() parameters
Parameters were created using wrong C types, which caused them to be of
wrong size on some architectures, causing problems.
The problem with SO_RCVLOWAT was found on s390 (big endian), while x86-64
didn't show it. After the fix, all tests pass on s390.
Then Stefano Garzarella pointed out that SO_VM_SOCKETS_* calls might have
a similar problem, which turned out to be true, hence, the second patch.
Changes for v8:
- Fix whitespace warnings from "checkpatch.pl --strict"
- Add maintainers to Cc:
Changes for v7:
- Rebase on top of https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net.git
- Add the "net" tags to the subjects
Changes for v6:
- rework the patch #3 to avoid creating a new file for new functions,
and exclude vsock_perf from calling the new functions.
- add "Reviewed-by:" to the patch #2.
Changes for v5:
- in the patch #2 replace the introduced uint64_t with unsigned long long
to match documentation
- add a patch #3 that verifies every setsockopt() call.
Changes for v4:
- add "Reviewed-by:" to the first patch, and add a second patch fixing
SO_VM_SOCKETS_* calls, which depends on the first one (hence, it's now
a patch series.)
Changes for v3:
- fix the same problem in vsock_perf and update commit message
Changes for v2:
- add "Fixes:" lines to the commit message
====================
Link: https://patch.msgid.link/20241203150656.287028-1-kshk@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Replace setsockopt() calls with calls to functions that follow
setsockopt() with getsockopt() and check that the returned value and its
size are the same as have been set. (Except in vsock_perf.)
Signed-off-by: Konstantin Shkolnyy <kshk@linux.ibm.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Change parameters of SO_VM_SOCKETS_* to unsigned long long as documented
in the vm_sockets.h, because the corresponding kernel code requires them
to be at least 64-bit, no matter what architecture. Otherwise they are
too small on 32-bit machines.
Fixes: 5c338112e4 ("test/vsock: rework message bounds test")
Fixes: 685a21c314 ("test/vsock: add big message test")
Fixes: 542e893fba ("vsock/test: two tests to check credit update logic")
Fixes: 8abbffd27c ("test/vsock: vsock_perf utility")
Signed-off-by: Konstantin Shkolnyy <kshk@linux.ibm.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This happens on 64-bit big-endian machines.
SO_RCVLOWAT requires an int parameter. However, instead of int, the test
uses unsigned long in one place and size_t in another. Both are 8 bytes
long on 64-bit machines. The kernel, having received the 8 bytes, doesn't
test for the exact size of the parameter, it only cares that it's >=
sizeof(int), and casts the 4 lower-addressed bytes to an int, which, on
a big-endian machine, contains 0. 0 doesn't trigger an error, SO_RCVLOWAT
returns with success and the socket stays with the default SO_RCVLOWAT = 1,
which results in vsock_test failures, while vsock_perf doesn't even notice
that it's failed to change it.
Fixes: b1346338fb ("vsock_test: POLLIN + SO_RCVLOWAT test")
Fixes: 542e893fba ("vsock/test: two tests to check credit update logic")
Fixes: 8abbffd27c ("test/vsock: vsock_perf utility")
Signed-off-by: Konstantin Shkolnyy <kshk@linux.ibm.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-12-03 (ice, idpf, ixgbe, ixgbevf, igb)
This series contains updates to ice, idpf, ixgbe, ixgbevf, and igb
drivers.
For ice:
Arkadiusz corrects search for determining whether PHY clock recovery is
supported on the device.
Przemyslaw corrects mask used for PHY timestamps on ETH56G devices.
Wojciech adds missing virtchnl ops which caused NULL pointer
dereference.
Marcin fixes VLAN filter settings for uplink VSI in switchdev mode.
For idpf:
Josh restores setting of completion tag for empty buffers.
For ixgbevf:
Jake removes incorrect initialization/support of IPSEC for mailbox
version 1.5.
For ixgbe:
Jake rewords and downgrades misleading message when negotiation
of VF mailbox version is not supported.
Tore Amundsen corrects value for BASE-BX10 capability.
For igb:
Yuan Can adds proper teardown on failed pci_register_driver() call.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
igb: Fix potential invalid memory access in igb_init_module()
ixgbe: Correct BASE-BX10 compliance code
ixgbe: downgrade logging of unsupported VF API version to debug
ixgbevf: stop attempting IPSEC offload on Mailbox API 1.5
idpf: set completion tag for "empty" bufs associated with a packet
ice: Fix VLAN pruning in switchdev mode
ice: Fix NULL pointer dereference in switchdev
ice: fix PHY timestamp extraction for ETH56G
ice: fix PHY Clock Recovery availability check
====================
Link: https://patch.msgid.link/20241203215521.1646668-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Previously a workaround was added to avoid syndrome 0xcdb051. It is
triggered when offload a rule with tunnel encapsulation, and
forwarding to another table, but not matching on the internal port in
firmware steering mode. The original workaround skips internal tunnel
port logic, which is not correct as not all cases are considered. As
an example, if vlan is configured on the uplink port, traffic can't
pass because vlan header is not added with this workaround. Besides,
there is no such issue for software steering. So, this patch removes
that, and returns error directly if trying to offload such rule for
firmware steering.
Fixes: 06b4eac9c4 ("net/mlx5e: Don't offload internal port if filter device is out device")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Tested-by: Frode Nordahl <frode.nordahl@canonical.com>
Reviewed-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Ariel Levkovich <lariel@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20241203204920.232744-7-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a multi-PF netdev, each traffic channel creates its own resources
against a specific PF.
In the cited commit, where this support was added, the channel_param
logic was mistakenly kept unchanged, so it always used the primary PF
which is found at priv->mdev.
In this patch we fix this by moving the logic to be per-channel, and
passing the correct mdev instance.
This bug happened to be usually harmless, as the resulting cparam
structures would be the same for all channels, due to identical FW logic
and decisions.
However, in some use cases, like fwreset, this gets broken.
This could lead to different symptoms. Example:
Error cqe on cqn 0x428, ci 0x0, qn 0x10a9, opcode 0xe, syndrome 0x4,
vendor syndrome 0x32
Fixes: e4f9686bde ("net/mlx5e: Let channels be SD-aware")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Lama Kayal <lkayal@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Link: https://patch.msgid.link/20241203204920.232744-6-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix the mentioned commit change for MPV mode, since in MPV mode the IB
device is shared between different core devices, so under this change
when moving both devices simultaneously to switchdev mode the IB device
removal and re-addition can race with itself causing unexpected behavior.
In such case do rescan_drivers() only once in order to add the ethernet
representor auxiliary device, and skip adding and removing IB devices.
Fixes: ab85ebf437 ("net/mlx5: E-switch, refactor eswitch mode change")
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20241203204920.232744-5-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
