Previously the stm32h7 interrupt thread cleared all non-masked interrupts.
If an interrupt was to occur during the handling of another interrupt its
flag would be unset, resulting in a lost interrupt.
This patches fixes the issue by clearing only the currently set interrupt
flags.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Link: https://lore.kernel.org/r/20200804195136.1485392-1-t.schramm@manjaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
CONFIG_OF_DYNAMIC and CONFIG_ACPI allow adding SPI devices at runtime
using a DeviceTree overlay or DSDT patch. CONFIG_SPI_SLAVE allows the
same via sysfs.
But there are no precautions to prevent adding a device below a
controller that's being removed. Such a device is unusable and may not
even be able to unbind cleanly as it becomes inaccessible once the
controller has been torn down. E.g. it is then impossible to quiesce
the device's interrupt.
of_spi_notify() and acpi_spi_notify() do hold a ref on the controller,
but otherwise run lockless against spi_unregister_controller().
Fix by holding the spi_add_lock in spi_unregister_controller() and
bailing out of spi_add_device() if the controller has been unregistered
concurrently.
Fixes: ce79d54ae4 ("spi/of: Add OF notifier handler")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.19+
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Octavian Purdila <octavian.purdila@intel.com>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Link: https://lore.kernel.org/r/a8c3205088a969dc8410eec1eba9aface60f36af.1596451035.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Hi,
This patchset mainly fixes some recently discovered problems about CS for
LPSPI module on i.MX8DXLEVK.
Add the dt-bindings description for the new property.
Clark Wang (4):
spi: lpspi: Fix kernel warning dump when probe fail after calling
spi_register
spi: lpspi: remove unused fsl_lpspi->chipselect
spi: lpspi: fix using CS discontinuously on i.MX8DXLEVK
dt-bindings: lpspi: New property in document DT bindings for LPSPI
.../bindings/spi/spi-fsl-lpspi.yaml | 7 ++++++
drivers/spi/spi-fsl-lpspi.c | 25 +++++++++++--------
2 files changed, 21 insertions(+), 11 deletions(-)
--
2.17.1
Simply copying all xfers from userspace into one bounce buffer causes
alignment problems if the SPI controller uses DMA.
Ensure that all transfer data blocks within the rx and tx bounce buffers
are aligned for DMA (according to ARCH_KMALLOC_MINALIGN).
Alignment may increase the usage of the bounce buffers. In some cases,
the buffers may need to be increased using the "bufsiz" module
parameter.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200728100832.24788-1-ceggers@arri.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Drivers using legacy PM have to manage PCI states and device's PM states
themselves. They also need to take care of configuration registers.
With improved and powerful support of generic PM, PCI Core takes care of
above mentioned, device-independent, jobs.
This driver makes use of PCI helper functions like
pci_save/restore_state(), pci_enable/disable_device(), pci_enable_wake()
and pci_set_power_state() to do required operations. In generic mode, they
are no longer needed.
Change function parameter in both .suspend() and .resume() to
"struct device*" type. Use dev_get_drvdata() to get drv data.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Link: https://lore.kernel.org/r/20200720155714.714114-1-vaibhavgupta40@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This converts the PPC4xx SPI driver to use GPIO descriptors.
The driver is already just picking some GPIOs from the device
tree so the conversion is pretty straight forward. However
this driver is looking form a pure "gpios" property rather
than the standard binding "cs-gpios" so we need to add a new
exception to the gpiolib OF parser to allow this for this
driver's compatibles.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linuxppc-dev@lists.ozlabs.org
Link: https://lore.kernel.org/r/20200714072226.26071-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Since ACPI_PTR() is used to NULLify the value when !CONFIG_ACPI,
struct 'spi_acpi_match' becomes defined but unused.
Fixes the following W=1 kernel build warning(s):
drivers/spi/spi-amd.c:297:36: warning: ‘spi_acpi_match’ defined but not used [-Wunused-const-variable=]
297 | static const struct acpi_device_id spi_acpi_match[] = {
| ^~~~~~~~~~~~~~
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Sanjay R Mehta <sanju.mehta@amd.com>
Link: https://lore.kernel.org/r/20200717135424.2442271-15-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/spi/spi-topcliff-pch.c:184: warning: Function parameter or member 'io_base_addr' not described in 'pch_spi_data'
drivers/spi/spi-topcliff-pch.c:184: warning: Function parameter or member 'pkt_tx_buff' not described in 'pch_spi_data'
drivers/spi/spi-topcliff-pch.c:184: warning: Function parameter or member 'pkt_rx_buff' not described in 'pch_spi_data'
drivers/spi/spi-topcliff-pch.c:184: warning: Function parameter or member 'dma' not described in 'pch_spi_data'
drivers/spi/spi-topcliff-pch.c:184: warning: Function parameter or member 'use_dma' not described in 'pch_spi_data'
drivers/spi/spi-topcliff-pch.c:184: warning: Function parameter or member 'save_total_len' not described in 'pch_spi_data'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200717135424.2442271-12-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/spi/spi-zynqmp-gqspi.c:205: warning: Function parameter or member 'slavecs' not described in 'zynqmp_gqspi_selectslave'
drivers/spi/spi-zynqmp-gqspi.c:205: warning: Function parameter or member 'slavebus' not described in 'zynqmp_gqspi_selectslave'
drivers/spi/spi-zynqmp-gqspi.c:205: warning: Excess function parameter 'flashcs' description in 'zynqmp_gqspi_selectslave'
drivers/spi/spi-zynqmp-gqspi.c:205: warning: Excess function parameter 'flashbus' description in 'zynqmp_gqspi_selectslave'
drivers/spi/spi-zynqmp-gqspi.c:902: warning: Function parameter or member 'dev' not described in 'zynqmp_qspi_suspend'
drivers/spi/spi-zynqmp-gqspi.c:902: warning: Excess function parameter '_dev' description in 'zynqmp_qspi_suspend'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/20200717135424.2442271-11-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/spi/spi-zynq-qspi.c:143: warning: Function parameter or member 'dev' not described in 'zynq_qspi'
drivers/spi/spi-zynq-qspi.c:334: warning: Function parameter or member 'spi' not described in 'zynq_qspi_config_op'
drivers/spi/spi-zynq-qspi.c:334: warning: Excess function parameter 'qspi' description in 'zynq_qspi_config_op'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Cc: Sureshkumar Relli <nagasure@xilinx.com>
Link: https://lore.kernel.org/r/20200717135424.2442271-10-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Also demote non-worthy kerneldoc headers to standard comment blocks.
Fixes the following W=1 kernel build warning(s):
drivers/spi/spi-pl022.c:304: warning: cannot understand function prototype: 'enum ssp_writing '
drivers/spi/spi-pl022.c:330: warning: Function parameter or member 'loopback' not described in 'vendor_data'
drivers/spi/spi-pl022.c:398: warning: Function parameter or member 'rx_lev_trig' not described in 'pl022'
drivers/spi/spi-pl022.c:398: warning: Function parameter or member 'tx_lev_trig' not described in 'pl022'
drivers/spi/spi-pl022.c:398: warning: Function parameter or member 'dma_running' not described in 'pl022'
drivers/spi/spi-pl022.c:670: warning: Function parameter or member 'pl022' not described in 'readwriter'
drivers/spi/spi-pl022.c:1250: warning: Function parameter or member 'irq' not described in 'pl022_interrupt_handler'
drivers/spi/spi-pl022.c:1250: warning: Function parameter or member 'dev_id' not described in 'pl022_interrupt_handler'
drivers/spi/spi-pl022.c:1343: warning: Function parameter or member 'pl022' not described in 'set_up_next_transfer'
drivers/spi/spi-pl022.c:1343: warning: Function parameter or member 'transfer' not described in 'set_up_next_transfer'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Sachin Verma <sachin.verma@st.com>
Link: https://lore.kernel.org/r/20200717135424.2442271-9-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/spi/spi-s3c64xx.c:150: warning: Function parameter or member 'quirks' not described in 's3c64xx_spi_port_config'
drivers/spi/spi-s3c64xx.c:150: warning: Function parameter or member 'clk_ioclk' not described in 's3c64xx_spi_port_config'
drivers/spi/spi-s3c64xx.c:189: warning: Function parameter or member 'pdev' not described in 's3c64xx_spi_driver_data'
drivers/spi/spi-s3c64xx.c:189: warning: Function parameter or member 'rx_dma' not described in 's3c64xx_spi_driver_data'
drivers/spi/spi-s3c64xx.c:189: warning: Function parameter or member 'tx_dma' not described in 's3c64xx_spi_driver_data'
drivers/spi/spi-s3c64xx.c:189: warning: Function parameter or member 'port_conf' not described in 's3c64xx_spi_driver_data'
drivers/spi/spi-s3c64xx.c:189: warning: Function parameter or member 'port_id' not described in 's3c64xx_spi_driver_data'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Andi Shyti <andi@etezian.org>
Cc: Jaswinder Singh <jassi.brar@samsung.com>
Cc: linux-samsung-soc@vger.kernel.org
Link: https://lore.kernel.org/r/20200717135424.2442271-8-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
ep93xx_spi_read_write() changed is parameters, but the function
documentation was left unchanged. Let's realign.
Fixes the following W=1 kernel build warning(s):
drivers/spi/spi-ep93xx.c:227: warning: Function parameter or member 'master' not described in 'ep93xx_spi_read_write'
drivers/spi/spi-ep93xx.c:227: warning: Excess function parameter 'espi' description in 'ep93xx_spi_read_write'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Mika Westerberg <mika.westerberg@iki.fi>
Link: https://lore.kernel.org/r/20200717135424.2442271-5-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/spi/spi-davinci.c:249: warning: Function parameter or member 'dspi' not described in 'davinci_spi_get_prescale'
drivers/spi/spi-davinci.c:249: warning: Function parameter or member 'max_speed_hz' not described in 'davinci_spi_get_prescale'
drivers/spi/spi-davinci.c:249: warning: Excess function parameter 'maxspeed_hz' description in 'davinci_spi_get_prescale'
drivers/spi/spi-davinci.c:719: warning: Function parameter or member 'data' not described in 'dummy_thread_fn'
drivers/spi/spi-davinci.c:719: warning: Excess function parameter 'context_data' description in 'dummy_thread_fn'
drivers/spi/spi-davinci.c:735: warning: Function parameter or member 'data' not described in 'davinci_spi_irq'
drivers/spi/spi-davinci.c:735: warning: Excess function parameter 'context_data' description in 'davinci_spi_irq'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200717135424.2442271-4-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
No attempt has been made to document any of the demoted functions here.
Fixes the following W=1 kernel build warning(s):
drivers/spi/spi-bitbang.c:181: warning: Function parameter or member 'spi' not described in 'spi_bitbang_setup'
drivers/spi/spi-bitbang.c:215: warning: Function parameter or member 'spi' not described in 'spi_bitbang_cleanup'
drivers/spi/spi-bitbang.c:434: warning: Function parameter or member 'bitbang' not described in 'spi_bitbang_stop'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200717135424.2442271-3-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Kerneldoc function parameter descriptions must be in '@.*: ' format.
Fixes the following W=1 kernel build warning(s):
drivers/spi/spi-loopback-test.c:897: warning: Function parameter or member 'spi' not described in 'spi_test_execute_msg'
drivers/spi/spi-loopback-test.c:897: warning: Function parameter or member 'test' not described in 'spi_test_execute_msg'
drivers/spi/spi-loopback-test.c:897: warning: Function parameter or member 'tx' not described in 'spi_test_execute_msg'
drivers/spi/spi-loopback-test.c:897: warning: Function parameter or member 'rx' not described in 'spi_test_execute_msg'
drivers/spi/spi-loopback-test.c:970: warning: Function parameter or member 'spi' not described in 'spi_test_run_test'
drivers/spi/spi-loopback-test.c:970: warning: Function parameter or member 'test' not described in 'spi_test_run_test'
drivers/spi/spi-loopback-test.c:970: warning: Function parameter or member 'tx' not described in 'spi_test_run_test'
drivers/spi/spi-loopback-test.c:970: warning: Function parameter or member 'rx' not described in 'spi_test_run_test'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Martin Sperl <kernel@martin.sperl.org>
Cc: linux-spi@vger.kernel.org
Link: https://lore.kernel.org/r/20200717135424.2442271-2-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Hello,
I've picked up and forward ported Martin Sperl's patches which add support for
effective_speed_hz to the SPI controllers found on all raspberry pi models.
See the following patch, which adds this feature to the SPI core, for more
information:
5d7e2b5ed5 spi: core: allow reporting the effectivly used speed_hz for a transfer
regards,
Marc
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Optimezed mem*io operations are defined for LE platforms, use them.
The ARM and !ARCH_EBSA110 dependencies for COMPILE_TEST were added
only for the _memcpy_fromio()/_memcpy_toio() functions. Drop these
dependencies.
Tested unaligned accesses on both sama5d2 and sam9x60 QSPI controllers
using SPI NOR flashes, everything works ok. The following performance
improvement can be seen when running mtd_speedtest:
sama5d2_xplained (mx25l25635e)
- before:
mtd_speedtest: eraseblock write speed is 983 KiB/s
mtd_speedtest: eraseblock read speed is 6150 KiB/s
- after:
mtd_speedtest: eraseblock write speed is 1055 KiB/s
mtd_speedtest: eraseblock read speed is 20144 KiB/s
sam9x60ek (sst26vf064b)
- before:
mtd_speedtest: eraseblock write speed is 4770 KiB/s
mtd_speedtest: eraseblock read speed is 8062 KiB/s
- after:
mtd_speedtest: eraseblock write speed is 4524 KiB/s
mtd_speedtest: eraseblock read speed is 21186 KiB/s
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200716043139.565734-1-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently we always defer idling of controllers to the SPI thread, the goal
being to ensure that we're doing teardown that's not suitable for atomic
context in an appropriate context and to try to batch up more expensive
teardown operations when the system is under higher load, allowing more
work to be started before the SPI thread is scheduled. However when the
controller does not require any substantial work to idle there is no need
to do this, we can instead save the context switch and immediately mark
the controller as idle. This is particularly useful for systems where there
is frequent but not constant activity.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20200715163610.9475-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
