It's been observed that in a corner case mwifiex_usb_tx_complete()
gets called before we exit from mwifiex_usb_host_to_card() after
submitting the urb. 'data_sent' flag remains set in this case. It
blocks further Tx packets and triggers watchdog timeout.
The problem is fixed by setting data_sent and port_block flag at
correct place.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Shengzhen Li <szli@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Following crash issue is observed during TCP traffic stress
test
[ 2253.625439] NMI watchdog: BUG: soft lockup - CPU#3 stuck for 22s!
[kworker/u17:1:5191]
[ 2253.625520] Call Trace:
[ 2253.625527] [<ffffffffc0b47030>] ? moal_spin_lock+0x30/0x30
[usb8xxx]
[ 2253.625533] [<ffffffffc0ac3ceb>] ? wlan_wmm_lists_empty+0xb/0xf0
[mlan]
[ 2253.625537] [<ffffffffc0ab0ea3>] mlan_main_process+0x1b3/0x720
[mlan]
[ 2253.625540] [<ffffffffc0b337f5>] woal_main_work_queue+0x45/0x80
[usb8xxx]
[ 2253.625543] [<ffffffff8108aaf0>] process_one_work+0x150/0x3f0
[ 2253.625545] [<ffffffff8108b1e1>] worker_thread+0x121/0x520
[ 2253.625547] [<ffffffff8108b0c0>] ? rescuer_thread+0x330/0x330
[ 2253.625549] [<ffffffff81090222>] kthread+0xd2/0xf0
[ 2253.625551] [<ffffffff81090150>] ?
kthread_create_on_node+0x1c0/0x1c0
[ 2253.625553] [<ffffffff8179423c>] ret_from_fork+0x7c/0xb0
[ 2253.625555] [<ffffffff81090150>] ?
kthread_create_on_node+0x1c0/0x1c0
In mwifiex_usb_tx_complete(), we are updating port->block_status first
and then freeing the skb attached to that URB. We may end up attaching
new skb to URB in a corner case and same will be freed. This results in
the kernel crash. The problem is solved by changing the sequence.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Shengzhen Li <szli@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Clearing the wowl wakeindicator happens with a rather odd
construction where the string "clear" is used to set the iovar
wowl_wakeind. This was implemented incorrectly as it caused an
out of bound access. Use an intermediate variable of correct
length and copy string in that. Problem was found using coverity.
Reviewed-by: Arend Van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Signed-off-by: Hante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The variable info is assigned to point to bcdc->msg[1], which is the
same as pointing to bcdc->buf. As that is what we want to access
make it clear by fixing the assignment. This also avoid out-of-bounds
errors from static analyzers are bcdc->msg[1] is not in the structure
definition.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Previously device used to start using IGTK key as Tx key as soon as it
gets downloaded in add_key(). This patch implements set_default_mgmt_key
handler. We will update Tx key ID in set_default_mgmt_key().
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use the wl18xx specific config firmware we now have available.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Booting multiple wl12xx and wl18xx devices using the same rootfs is
a pain. You currently have to symlink the right nvs file depending
on the wl12xx type.
For example, with wl1271-nvs.bin being a symlink to wl127x-nvs.bin
by default and trying to bring up a wl128x based device:
wlcore: ERROR nvs size is not as expected: 1113 != 912
wlcore: ERROR NVS file is needed during boot
wlcore: ERROR NVS file is needed during boot
wlcore: ERROR firmware boot failed despite 3 retries
Note that wl18xx uses a separate config firmware wl18xx-conf.bin
that can be generated with tools using the following two git repos:
git.ti.com/wilink8-wlan/18xx-ti-utils
git.ti.com/wilink8-wlan/wl18xx_fw
So let's not configure the nvs file for wl18xx as it's not needed
AFAIK. If it turns out that we also need the nvs file for wl18xx,
we can just add it to the config firmware data for wl18xx.
Let's fix the issue by using the chip specific config firmware
data, and make sure we produce understandable warnings if something
is missing.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Configure the config firmware names and make it available
in platform data.
Let's also fix the order of the struct wilink_family_data
while at it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Configure the config firmware names and make it available
in platform data.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move struct wilink_family_data to be available for all TI WLAN
variants. And fix familiy typo, it should be just family.
Looks like wl12xx use two different nvs.bin files and wl18xx
uses a different conf.bin file.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* added support for MU-MIMO sniffer
* added support for RRM by scan
* added support for packet injection
* migrate to devm memory allocation handling
* some fixes, mostly in DQA and new HW support
* other generic cleanups
There's no need to declare a list and then init it manually,
just use the LIST_HEAD() macro.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no need to declare a list and then init it manually,
just use the LIST_HEAD() macro.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently it is logged as UNKNOWN.
Also, 0x6c seems to be the permanent ID for this command, remove
incorrect comment and uncomment the command from the commands
list.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to access cached/paged memory, there are a couple of firmware
commands (one for UMAC and one for LMAC) that let the host access memory
and registers indirectly. Since this is done by the firmware on behalf
of the host, even if memory is paged out or cached, the host will
retrieve the memory as the firmware sees it (paged out memory will get
paged in).
Export this mechanism via a debugfs entry for both read and write
access.
WARNING: This mechanism has no protections at all. Invalid addresses may
crash or hang the firmware. Writing to arbitrary memory also comes with
no guarantees.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no need for the common MAC context function to have an
if on AP mode, the values can be overridden in the AP-specific
function later. Clean that up by adding the full command as a
new parameter to the AP-specific function, and doing it there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we get an unexpected Block Ack Request frame, the BAID from
the hardware will be invalid, and we'll pass it to mac80211 for
further handling (sending a delBA action frame.)
Add a comment explaining that, in case anyone looks in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no point in making this an out-of-line function
since it just calls a single other function with a few
changed parameters.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This will be used by more than MVM, so move it to iwlwifi
While at it, rename WRD_METHOD to the more appropriate
WRDD_METHOD and add some documentation.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For automatic testing packet injection can be useful.
Support injection through debugfs.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Implement support for RRM by adding an option to configure the scan
dwell time and reporting scan start time and BSS detection time, and
Advertise support for these features.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
On default queue we will not receive frame release notification,
but the BAR itself.
Upon receiving the BAR driver should look at the NSSN and adjust
window accordingly.
Fixes: b915c10174 ("iwlwifi: mvm: add reorder buffer per queue")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There was recently a Full AP mode feature added where hostap adds
the station at auth stage, and not assoc.
However, when running with legacy hostapd, we get the auth response
before station was added, and tx_skb_non_sta fails to allocate
a queue, resulting in a complete failure of association.
Take care of this situation as well.
Add a warning when no valid queue is returned at all and make mvm
drop the packet instead of passing it on.
Refactor the function a bit while at it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In 9000 family products we added an option to let the OEM fuse the
mac address via registers. If these registers are zeroed we use the OTP
address instead. Make sure that the address provided by the OEM is valid
and, if not, fall back to the OTP address as well.
Fixes: commit 17c867bfe8 ("iwlwifi: add support for getting HW address from CSR")
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When comparing command IDs, the group should be taken
into account so the same command/notification from a
different group doesn't trigger anything unexpected.
Fix this by comparing to the wide ID.
Fixes: commit 1738d60b31 ("iwlwifi: mvm: handle RX MPDUs separately")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Use skb_queue_empty() and not skb_peek_tail() to check for
empty list.
Avoid a redundant check as well - loop will take care of it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If adapter is null the error exit path in mwifiex_shutdown_sw is
to down the semaphore sem and print some debug via mwifiex_dbg.
However, passing a NULL adapter to mwifiex_dbg causes a null
pointer deference when accessing adapter->dev. This fix checks
for a null adapter at the start of the function and to exit
without the need to up the semaphore and we also skip the debug
to avoid the null pointer dereference.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
smatch reports:
sta_cmdresp.c:1053 mwifiex_create_custom_regdomain() warn: possible memory leak of 'regd'
Indeed, mwifiex_create_custom_regdomain() returns NULL in the
case that channel is missing in the TLV without freeing regd.
Moreover, some other error paths in this function return ERR_PTR
values which are assigned without checking to the regd field in
the mwifiex_adapter struct. The latter is only null-checked where
used.
Fix by freeing regd in the error path, and only update
priv->adapter->regd if the returned pointer is valid.
Cc: Amitkumar Karwar <akarwar@marvell.com>
Cc: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This powers down the 8192e correctly, or at least to the point where
the firmware will load again, when reloading the driver module.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* work for new hardware support continues
* dynamic queue allocation stabilization
* improvements in the MSIx code
* multiqueue support work continues
* new firmware version support
* general cleanups and improvements
Alexei Starovoitov says:
====================
ip_tunnel: add collect_md mode to IPv4/IPv6 tunnels
Similar to geneve, vxlan, gre tunnels implement 'collect metadata' mode
in ipip, ipip6, ip6ip6 tunnels.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
the test creates 3 namespaces with veth connected via bridge.
First two namespaces simulate two different hosts with the same
IPv4 and IPv6 addresses configured on the tunnel interface and they
communicate with outside world via standard tunnels.
Third namespace creates collect_md tunnel that is driven by BPF
program which selects different remote host (either first or
second namespace) based on tcp dest port number while tcp dst
ip is the same.
This scenario is rough approximation of load balancer use case.
The tests check both traditional tunnel configuration and collect_md mode.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
