This version brings along following updates:
- Disable stutter when programming watermarks on dcn32
- Fix pbn_div Calculation Error
- Correct sequences and delays for DCN35 PG & RCG
- Define interfaces for hubbub perfmance monitoring support
- Extend to read eDP general capability 2
- Indicate when custom brightness curves are in use
- Dont wait for pipe update during medupdate/highirq
- Add HDCP retry_limit control parameter
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dm_mst_get_pbn_divider() returns value integer coming from
the cast from fixed point, but the casted integer will then be used
in dfixed_const to be multiplied by 4096. The cast from fixed point to integer
causes the calculation error becomes bigger when multiplied by 4096.
That makes the calculated pbn_div value becomes smaller than
it should be, which leads to the req_slot number becomes bigger.
Such error is getting reflected in 8k30 timing,
where the correct and incorrect calculated req_slot 62.9 Vs 63.1.
That makes the wrong calculation failed to light up 8k30
after a dock under HBR3 x 4.
[How]
Restore the accuracy by keeping the fraction part
calculated for the left shift operation.
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The error message "failed to initialize sw for display support" is used
for both DRM device and vblank initialization failures, making it difficult
to identify the specific failure during troubleshooting.
[How]
Update the vblank initialization error message to
"failed to initialize vblank for display support"
to distinguish it from the DRM device init failure.
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There is a `scale` sysfs attribute that can be used to indicate when
non-linear brightness scaling is in use. As Custom brightness curves
work by linear interpolation of points the scale is no longer linear.
[How]
Indicate non-linear scaling when custom brightness curves in use and
linear scaling otherwise.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <superm1@kernel.org>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DM should be able to control HDCP retry limit via configurable
parameter.
[How]
Expose a retry_limit parameter for controlling the maximum number of
retries and lift the hardcode out to DM.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Oleh Kuzhylnyi <okuzhyln@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Implement caching separately for SystemMetrics table from PMFW. The same
table could be used for multiple interfaces. Hence, cache it internally
to avoid multiple queries to the firmware. For SystemMetrics table, 5ms
cache interval is sufficient.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Asad Kamal <asad.kamal@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
v1:
Returns different error codes based on the scenario to help the user app understand
the AMDGPU device status when an exception occurs.
v2:
change -NODEV to -EBUSY.
Signed-off-by: Yang Wang <kevinyang.wang@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use int instead of uint32_t for 'ret' variable to store negative error
codes or zero returned by other functions.
Storing the negative error codes in unsigned type, doesn't cause an issue
at runtime but can be confusing. Additionally, assigning negative error
codes to unsigned type may trigger a GCC warning when the -Wsign-conversion
flag is enabled.
No effect on runtime.
Signed-off-by: Qianfeng Rong <rongqianfeng@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For ternary operators in the form of "a ? true : false", if 'a' itself
returns a boolean result, the ternary operator can be omitted. Remove
redundant ternary operators to clean up the code.
Signed-off-by: Liao Yuanhong <liaoyuanhong@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For ternary operators in the form of "a ? true : false", if 'a' itself
returns a boolean result, the ternary operator can be omitted. Remove
redundant ternary operators to clean up the code.
Signed-off-by: Liao Yuanhong <liaoyuanhong@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For ternary operators in the form of "a ? true : false", if 'a' itself
returns a boolean result, the ternary operator can be omitted. Remove
redundant ternary operators to clean up the code.
Signed-off-by: Liao Yuanhong <liaoyuanhong@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For ternary operators in the form of "a ? true : false", if 'a' itself
returns a boolean result, the ternary operator can be omitted. Remove
redundant ternary operators to clean up the code.
Signed-off-by: Liao Yuanhong <liaoyuanhong@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For ternary operators in the form of "a ? true : false", if 'a' itself
returns a boolean result, the ternary operator can be omitted. Remove
redundant ternary operators to clean up the code. Swap variable positions
on either side of '==' to enhance readability.
Signed-off-by: Liao Yuanhong <liaoyuanhong@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For ternary operators in the form of "a ? true : false", if 'a' itself
returns a boolean result, the ternary operator can be omitted. Remove
redundant ternary operators to clean up the code. Swap variable positions
on either side of '!=' to enhance readability.
Signed-off-by: Liao Yuanhong <liaoyuanhong@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For ternary operators in the form of "a ? true : false", if 'a' itself
returns a boolean result, the ternary operator can be omitted. Remove
redundant ternary operators to clean up the code.
Signed-off-by: Liao Yuanhong <liaoyuanhong@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For ternary operators in the form of "a ? true : false" or
"a ? false : true", if 'a' itself returns a boolean result, the ternary
operator can be omitted. Remove redundant ternary operators to clean up the
code.
Signed-off-by: Liao Yuanhong <liaoyuanhong@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a detect and reset callback and add the implementation
for mes. The callback will detect all hung queues of a
particular ip type (e.g., GFX or compute or SDMA) and
reset them.
v2: increase reset counter and set fence force completion
v3: Removed userq_mutex in mes_userq_detect_and_reset since the driver holds it when calling
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Jesse Zhang <Jesse.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use negative error code -EINVAL instead of positive EINVAL in the default
case of svm_ioctl() to conform to Linux kernel error code conventions.
Fixes: 42de677f79 ("drm/amdkfd: register svm range")
Signed-off-by: Qianfeng Rong <rongqianfeng@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some SOCs which are part of the cyan skillfish family
rely on an explicit firmware for IP discovery. Add support
for the gpu_info firmware.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Align the function headers for `amdgpu_max_hdmi_pixel_clock` and
`amdgpu_connector_dvi_mode_valid` with the function implementations so
they match the expected kdoc style.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/amdgpu_connectors.c:1199: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Returns the maximum supported HDMI (TMDS) pixel clock in KHz.
drivers/gpu/drm/amd/amdgpu/amdgpu_connectors.c:1212: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Validates the given display mode on DVI and HDMI connectors.
Fixes: 585b2f685c ("drm/amdgpu: Respect max pixel clock for HDMI and DVI-D (v2)")
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Current mem limit check leaks some GTT memory (reserved_for_pt
reserved_for_ras + adev->vram_pin_size) for small APUs.
Since carveout VRAM is tunable on APUs, there are three case
regarding the carveout VRAM size relative to GTT:
1. 0 < carveout < gtt
apu_prefer_gtt = true, is_app_apu = false
2. carveout > gtt / 2
apu_prefer_gtt = false, is_app_apu = false
3. 0 = carveout
apu_prefer_gtt = true, is_app_apu = true
It doesn't make sense to check below limitation in case 1
(default case, small carveout) because the values in the below
expression are mixed with carveout and gtt.
adev->kfd.vram_used[xcp_id] + vram_needed >
vram_size - reserved_for_pt - reserved_for_ras -
atomic64_read(&adev->vram_pin_size)
gtt: kfd.vram_used, vram_needed, vram_size
carveout: reserved_for_pt, reserved_for_ras, adev->vram_pin_size
In case 1, vram allocation will go to gtt domain, skip vram check
since ttm_mem_limit check already cover this allocation.
Signed-off-by: Yifan Zhang <yifan1.zhang@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes a bug where unbinding of the GPU would leave the oem i2c adapter
registered resulting in a null pointer dereference when applications try
to access the invalid device.
Fixes: 3d5470c973 ("drm/amd/display/dm: add support for OEM i2c bus")
Cc: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Geoffrey McRae <geoffrey.mcrae@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support for forcing completion of userq fences.
This is needed for userq resets and asic resets so that we
can set the error on the fence and force completion.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Helper function to detect and reset hung queues. MES will
return an array of doorbell indices of which queues are hung
and were optionally reset.
v2: Clear the doorbell array before detection
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Jesse Zhang <Jesse.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This commit implements the actual MES (Micro Engine Scheduler) suspend
and resume gang operations for version 12 hardware. Previously these
functions were just stubs returning success.
v2: Always use AMDGPU_MES_SCHED_PIPE
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Jesse Zhang <Jesse.Zhang@amd.com>
Add two new function pointers to struct amdgpu_userq_funcs:
- preempt: To handle preemption of user mode queues
- restore: To restore preempted user mode queues
These callbacks will allow the driver to properly manage queue
preemption and restoration when needed, such as during context
switching or priority changes.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Jesse Zhang <Jesse.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add more information in the debugfs which is needed to dump
a pagetable correctly for userqueues where vmid is not known
in the kernel.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Correct valid_bits and ms_chk_bits of section info field for bad page
threshold exceed CPER to match OOB's behavior.
Signed-off-by: Xiang Liu <xiang.liu@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When creating p2p links, KFD needs to check XGMI link
with two conditions, hive_id and is_sharing_enabled,
but it is missing to check is_sharing_enabled, so add
it to fix the error.
Signed-off-by: Eric Huang <jinhuieric.huang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Change the 'ret' variable in ci_populate_all_graphic_levels()
and ci_populate_all_memory_levels() from u32 to int, as it needs to store
either negative error codes or zero returned by other functions.
Storing the negative error codes in unsigned type, doesn't cause an issue
at runtime but can be confusing. Additionally, assigning negative error
codes to unsigned type may trigger a GCC warning when the -Wsign-conversion
flag is enabled.
No effect on runtime.
Signed-off-by: Qianfeng Rong <rongqianfeng@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For ternary operators in the form of "a ? true : false", if 'a' itself
returns a boolean result, the ternary operator can be omitted. Remove
redundant ternary operators to clean up the code.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Liao Yuanhong <liaoyuanhong@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For ternary operators in the form of "a ? true : false", if 'a' itself
returns a boolean result, the ternary operator can be omitted. Remove
redundant ternary operators to clean up the code.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Liao Yuanhong <liaoyuanhong@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For ternary operators in the form of "a ? false : true", if 'a' itself
returns a boolean result, the ternary operator can be omitted. Remove
redundant ternary operators to clean up the code.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Liao Yuanhong <liaoyuanhong@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For ternary operators in the form of "a ? false : true", if 'a' itself
returns a boolean result, the ternary operator can be omitted. Remove
redundant ternary operators to clean up the code.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Liao Yuanhong <liaoyuanhong@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For ternary operators in the form of "a ? false : true", if 'a' itself
returns a boolean result, the ternary operator can be omitted. Remove
redundant ternary operators to clean up the code.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Liao Yuanhong <liaoyuanhong@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
