Hi,
This series adds support for ramp delay on mcp16502. It also adds
some cleanup on mcp16502.
Apart from that patches 1/6 fixes the selector validation in case
the regulator::desc::linear_min_sel is not zero.
Thank you,
Claudiu Beznea
Changes in v3:
- fix compilation error in patch 5/6
Reported-by: kernel test robot <lkp@intel.com>
Changes in v2:
- rebase on top of regulator/for-next
- checked 1/6 and 3/6 applies on top of regulator/for-5.10
Claudiu Beznea (6):
regulator: core: validate selector against linear_min_sel
regulator: core: do not continue if selector match
regulator: mcp16502: add linear_min_sel
regulator: mcp16502: adapt for get/set on other registers
regulator: mcp16502: add support for ramp delay
regulator: mcp16502: remove void documentation of struct mcp16502
drivers/regulator/core.c | 12 +++-
drivers/regulator/helpers.c | 3 +-
drivers/regulator/mcp16502.c | 135 ++++++++++++++++++++++++++++++++++++-------
3 files changed, 127 insertions(+), 23 deletions(-)
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
RFC for adding a support for typical voltage scaling connection
In few occasions there has been a need to scale the voltage output
from bucks on BD71837. Usually this is done when buck8 is used to
power specific GPU which can utilize voltages down to 0.7V. As lowest
the buck8 on BD71837 can go is 0.8V, and external connection is used to
scale the voltages.
The BD71837, BD71847 and BD71850 bucks can be adjusted by pulling up the
feedback pin using suitable voltage/resistors.
|---------------|
| buck 8 |-------+----->Vout
| | |
|---------------| |
| |
| |
+-------+--R2----+
|
R1
|
V FB-pull-up
This will scale the voltage as follows:
- Vout_o = Vo - (Vpu - Vo)*R2/R1
- Linear_step = step_orig*(R1+R2)/R1
where:
Vout_o is adjusted voltage output at vsel reg value 0
Vo is original voltage output at vsel reg value 0
Vpu is the pull-up voltage V FB-pull-up in the picture
R1 and R2 are resistor values.
>From HW point of view this does not need to be limited to buck 8. This
connection can be used to adjust output from any of the bucks on
BD71837/47/50.
As this seems to be a 'de-facto' way to scale the voltages on BD71837 it
might be a good idea to support computing the new voltage ranges for
bucks based on the V-pull-up and resistor R1/R2 values given from
device-tree. This allows describing the external HW connection using DT
to correctly scale the voltages.
This RFC uses "rohm,feedback-pull-up-r1-ohms" and
"rohm,feedback-pull-up-r2-ohms" to provide the resistor values - but
these names (without the picture) might not be too descriptive. I am
grateful for all suggestions as better and more descriptive names.
This patch series is an RFC because this connection feels somewhat
"hacky". OTOH - when hack becomes widely used, it is less of an hack and
more of a standard - and occasionally supporting HW hacks using SW may
benefit us all, right? :)
The other thing some projects do is allowing the change of BD71837 buck8
voltages when buck8 is enabled. This however will introduce voltage
spikes as buck8 was not originally designed for this. The specific HW
platform must be evaluated to be able to tolerate these spikes. Thus
this patch series does not support buck8 voltage changes when buck8 is
enabled. I wonder if this should be allowed per some config option(?) I
don't want to help people frying their boards... Opinions? Is there
suggested way of allowing this type of features at own risk? Config or
even Some #ifdef which is not listed in Kconfig? Device-tree property?
If you have (good) suggestions I could add the optional (non default)
DVS support for non DVS bucks on BD71837.
Matti Vaittinen (3):
dt-bindings: regulator: BD71837 support commonly used feedback
connection
dt-bindings: regulator: BD71847 support commonly used feedback
connection
regulator: bd718x7: Support external connection to scale voltages
.../regulator/rohm,bd71837-regulator.yaml | 48 +++++
.../regulator/rohm,bd71847-regulator.yaml | 49 ++++++
drivers/regulator/bd718x7-regulator.c | 164 +++++++++++++++++-
3 files changed, 254 insertions(+), 7 deletions(-)
base-commit: 3cea11cd5e
--
2.21.3
--
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND
~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =]
Setups where regulator (especially the buck8) output voltage is scaled
by adding external connection where some other regulator output is
connected to feedback-pin (over suitable resistors) is getting popular
amongst users of BD71837. This allows for example scaling down the
buck8 voltages to suit lover GPU voltages for projects where buck8 is
(ab)used to supply power for GPU. As a note - some setups do allow DVS
for buck8. This do produce voltage spikes and the HW must be evaluated
to be able to survive them. Thus this commit still keep the DVS disabled
for non DVS bucks by default. Let's not help you burn your proto board.
Allow describing this external connection from DT and scale the
voltages accordingly. This is what the connection should look like:
|------------|
| buck 8 |-------+----->Vout
| | |
|------------| |
| FB pin |
| |
+-------+--R2---+
|
R1
|
V FB-pull-up
Here the buck output is sifted according to formula:
Vout_o = Vo - (Vpu - Vo)*R2/R1
Linear_step = step_orig*(R1+R2)/R1
where:
Vout_o is adjusted voltage output at vsel reg value 0
Vo is original voltage output at vsel reg value 0
Vpu is the pull-up voltage V FB-pull-up in the picture
R1 and R2 are resistor values.
Bring support for specifying the Vpu, R1 and R2 from device tree and
scale voltages if they are given.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/89b2be87074f307a8823f15f34e1f662023cbf36.1604994184.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull x86 fixes from Thomas Gleixner:
"Three fixes all related to #DB:
- Handle the BTF bit correctly so it doesn't get lost due to a kernel
#DB
- Only clear and set the virtual DR6 value used by ptrace on user
space triggered #DB. A kernel #DB must leave it alone to ensure
data consistency for ptrace.
- Make the bitmasking of the virtual DR6 storage correct so it does
not lose DR_STEP"
* tag 'x86-urgent-2020-11-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/debug: Fix DR_STEP vs ptrace_get_debugreg(6)
x86/debug: Only clear/set ->virtual_dr6 for userspace #DB
x86/debug: Fix BTF handling
Pull timer fixes from Thomas Gleixner:
"A few fixes for timers/timekeeping:
- Prevent undefined behaviour in the timespec64_to_ns() conversion
which is used for converting user supplied time input to
nanoseconds. It lacked overflow protection.
- Mark sched_clock_read_begin/retry() to prevent recursion in the
tracer
- Remove unused debug functions in the hrtimer and timerlist code"
* tag 'timers-urgent-2020-11-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
time: Prevent undefined behaviour in timespec64_to_ns()
timers: Remove unused inline funtion debug_timer_free()
hrtimer: Remove unused inline function debug_hrtimer_free()
time/sched_clock: Mark sched_clock_read_begin/retry() as notrace
Pull smp fix from Thomas Gleixner:
"A single fix for stop machine.
Mark functions no trace to prevent a crash caused by recursion when
enabling or disabling a tracer on RISC-V (probably all architectures
which patch through stop machine)"
* tag 'smp-urgent-2020-11-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
stop_machine, rcu: Mark functions as notrace
Pull locking fixes from Thomas Gleixner:
"A couple of locking fixes:
- Fix incorrect failure injection handling in the fuxtex code
- Prevent a preemption warning in lockdep when tracking
local_irq_enable() and interrupts are already enabled
- Remove more raw_cpu_read() usage from lockdep which causes state
corruption on !X86 architectures.
- Make the nr_unused_locks accounting in lockdep correct again"
* tag 'locking-urgent-2020-11-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
lockdep: Fix nr_unused_locks accounting
locking/lockdep: Remove more raw_cpu_read() usage
futex: Fix incorrect should_fail_futex() handling
lockdep: Fix preemption WARN for spurious IRQ-enable
Pull char/misc fixes/removals from Greg KH:
"Here's some small fixes for 5.10-rc2 and a big driver removal.
The fixes are for some reported issues in the interconnect and
coresight drivers, nothing major.
The "big" driver removal is the MIC drivers have been asked to be
removed as the hardware never shipped and Intel no longer wants to
maintain something that no one can use. This is welcomed by many as
the DMA usage of these drivers was "interesting" and the security
people were starting to question some issues that were starting to be
found in the codebase.
Note, one of the subsystems for this driver, the "VOP" code, will
probably come back in future kernel versions as it was looking to
potentially solve some PCIe virtualization issues that a number of
other vendors were wanting to solve. But as-is, this codebase didn't
work for anyone else so no actual functionality is being removed.
All of these have been in linux-next with no reported issues"
* tag 'char-misc-5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
coresight: cti: Initialize dynamic sysfs attributes
coresight: Fix uninitialised pointer bug in etm_setup_aux()
coresight: add module license
misc: mic: remove the MIC drivers
interconnect: qcom: use icc_sync state for sm8[12]50
interconnect: qcom: Ensure that the floor bandwidth value is enforced
interconnect: qcom: sc7180: Init BCMs before creating the nodes
interconnect: qcom: sdm845: Init BCMs before creating the nodes
interconnect: Aggregate before setting initial bandwidth
interconnect: qcom: sdm845: Enable keepalive for the MM1 BCM
Pull driver core and documentation fixes from Greg KH:
"Here is one tiny debugfs change to fix up an API where the last user
was successfully fixed up in 5.10-rc1 (so it couldn't be merged
earlier), and a much larger Documentation/ABI/ update to the files so
they can be automatically parsed by our tools.
The Documentation/ABI/ updates are just formatting issues, small ones
to bring the files into parsable format, and have been acked by
numerous subsystem maintainers and the documentation maintainer. I
figured it was good to get this into 5.10-rc2 to help wih the merge
issues that would arise if these were to stick in linux-next until
5.11-rc1.
The debugfs change has been in linux-next for a long time, and the
Documentation updates only for the last linux-next release"
* tag 'driver-core-5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (40 commits)
scripts: get_abi.pl: assume ReST format by default
docs: ABI: sysfs-class-led-trigger-pattern: remove hw_pattern duplication
docs: ABI: sysfs-class-backlight: unify ABI documentation
docs: ABI: sysfs-c2port: remove a duplicated entry
docs: ABI: sysfs-class-power: unify duplicated properties
docs: ABI: unify /sys/class/leds/<led>/brightness documentation
docs: ABI: stable: remove a duplicated documentation
docs: ABI: change read/write attributes
docs: ABI: cleanup several ABI documents
docs: ABI: sysfs-bus-nvdimm: use the right format for ABI
docs: ABI: vdso: use the right format for ABI
docs: ABI: fix syntax to be parsed using ReST notation
docs: ABI: convert testing/configfs-acpi to ReST
docs: Kconfig/Makefile: add a check for broken ABI files
docs: abi-testing.rst: enable --rst-sources when building docs
docs: ABI: don't escape ReST-incompatible chars from obsolete and removed
docs: ABI: create a 2-depth index for ABI
docs: ABI: make it parse ABI/stable as ReST-compatible files
docs: ABI: sysfs-uevent: make it compatible with ReST output
docs: ABI: testing: make the files compatible with ReST output
...
Pull staging driver fixes from Greg KH:
"Here are some small staging driver fixes for issues that have been
reported in 5.10-rc1:
- octeon driver fixes
- wfx driver fixes
- memory leak fix in vchiq driver
- fieldbus driver bugfix
- comedi driver bugfix
All of these have been in linux-next with no reported issues"
* tag 'staging-5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: fieldbus: anybuss: jump to correct label in an error path
staging: wfx: fix test on return value of gpiod_get_value()
staging: wfx: fix use of uninitialized pointer
staging: mmal-vchiq: Fix memory leak for vchiq_instance
staging: comedi: cb_pcidas: Allow 2-channel commands for AO subdevice
staging: octeon: Drop on uncorrectable alignment or FCS error
staging: octeon: repair "fixed-link" support
Pull tty/serial fixes from Greg KH:
"Here are some small TTY and Serial driver fixes for reported issues
for 5.10-rc2. They include:
- vt ioctl bugfix for reported problems
- fsl_lpuart serial driver fix
- 21285 serial driver bugfix
All have been in linux-next with no reported issues"
* tag 'tty-5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
vt_ioctl: fix GIO_UNIMAP regression
vt: keyboard, extend func_buf_lock to readers
vt: keyboard, simplify vt_kdgkbsent
tty: serial: fsl_lpuart: LS1021A has a FIFO size of 16 words, like LS1028A
tty: serial: 21285: fix lockup on open
Pull USB driver fixes from Greg KH:
"Here are a number of small bugfixes for reported issues in some USB
drivers. They include:
- typec bugfixes
- xhci bugfixes and lockdep warning fixes
- cdc-acm driver regression fix
- kernel doc fixes
- cdns3 driver bugfixes for a bunch of reported issues
- other tiny USB driver fixes
All have been in linux-next with no reported issues"
* tag 'usb-5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: cdns3: gadget: own the lock wrongly at the suspend routine
usb: cdns3: Fix on-chip memory overflow issue
usb: cdns3: gadget: suspicious implicit sign extension
xhci: Don't create stream debugfs files with spinlock held.
usb: xhci: Workaround for S3 issue on AMD SNPS 3.0 xHC
xhci: Fix sizeof() mismatch
usb: typec: stusb160x: fix signedness comparison issue with enum variables
usb: typec: add missing MODULE_DEVICE_TABLE() to stusb160x
USB: apple-mfi-fastcharge: don't probe unhandled devices
usbcore: Check both id_table and match() when both available
usb: host: ehci-tegra: Fix error handling in tegra_ehci_probe()
usb: typec: stusb160x: fix an IS_ERR() vs NULL check in probe
usb: typec: tcpm: reset hard_reset_count for any disconnect
usb: cdc-acm: fix cooldown mechanism
usb: host: fsl-mph-dr-of: check return of dma_set_mask()
usb: fix kernel-doc markups
usb: typec: stusb160x: fix some signedness bugs
usb: cdns3: Variable 'length' set but not used
Pull kvm fixes from Paolo Bonzini:
"ARM:
- selftest fix
- force PTE mapping on device pages provided via VFIO
- fix detection of cacheable mapping at S2
- fallback to PMD/PTE mappings for composite huge pages
- fix accounting of Stage-2 PGD allocation
- fix AArch32 handling of some of the debug registers
- simplify host HYP entry
- fix stray pointer conversion on nVHE TLB invalidation
- fix initialization of the nVHE code
- simplify handling of capabilities exposed to HYP
- nuke VCPUs caught using a forbidden AArch32 EL0
x86:
- new nested virtualization selftest
- miscellaneous fixes
- make W=1 fixes
- reserve new CPUID bit in the KVM leaves"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: vmx: remove unused variable
KVM: selftests: Don't require THP to run tests
KVM: VMX: eVMCS: make evmcs_sanitize_exec_ctrls() work again
KVM: selftests: test behavior of unmapped L2 APIC-access address
KVM: x86: Fix NULL dereference at kvm_msr_ignored_check()
KVM: x86: replace static const variables with macros
KVM: arm64: Handle Asymmetric AArch32 systems
arm64: cpufeature: upgrade hyp caps to final
arm64: cpufeature: reorder cpus_have_{const, final}_cap()
KVM: arm64: Factor out is_{vhe,nvhe}_hyp_code()
KVM: arm64: Force PTE mapping on fault resulting in a device mapping
KVM: arm64: Use fallback mapping sizes for contiguous huge page sizes
KVM: arm64: Fix masks in stage2_pte_cacheable()
KVM: arm64: Fix AArch32 handling of DBGD{CCINT,SCRext} and DBGVCR
KVM: arm64: Allocate stage-2 pgd pages with GFP_KERNEL_ACCOUNT
KVM: arm64: Drop useless PAN setting on host EL1 to EL2 transition
KVM: arm64: Remove leftover kern_hyp_va() in nVHE TLB invalidation
KVM: arm64: Don't corrupt tpidr_el2 on failed HVC call
x86/kvm: Reserve KVM_FEATURE_MSI_EXT_DEST_ID
Pull vhost fixes from Michael Tsirkin:
"Fixes all over the place.
A new UAPI is borderline: can also be considered a new feature but
also seems to be the only way we could come up with to fix addressing
for userspace - and it seems important to switch to it now before
userspace making assumptions about addressing ability of devices is
set in stone"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vdpasim: allow to assign a MAC address
vdpasim: fix MAC address configuration
vdpa: handle irq bypass register failure case
vdpa_sim: Fix DMA mask
Revert "vhost-vdpa: fix page pinning leakage in error path"
vdpa/mlx5: Fix error return in map_direct_mr()
vhost_vdpa: Return -EFAULT if copy_from_user() fails
vdpa_sim: implement get_iova_range()
vhost: vdpa: report iova range
vdpa: introduce config op to get valid iova range
Pull more flexible-array member conversions from Gustavo A. R. Silva:
"Replace zero-length arrays with flexible-array members"
* tag 'flexible-array-conversions-5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
printk: ringbuffer: Replace zero-length array with flexible-array member
net/smc: Replace zero-length array with flexible-array member
net/mlx5: Replace zero-length array with flexible-array member
mei: hw: Replace zero-length array with flexible-array member
gve: Replace zero-length array with flexible-array member
Bluetooth: btintel: Replace zero-length array with flexible-array member
scsi: target: tcmu: Replace zero-length array with flexible-array member
ima: Replace zero-length array with flexible-array member
enetc: Replace zero-length array with flexible-array member
fs: Replace zero-length array with flexible-array member
Bluetooth: Replace zero-length array with flexible-array member
params: Replace zero-length array with flexible-array member
tracepoint: Replace zero-length array with flexible-array member
platform/chrome: cros_ec_proto: Replace zero-length array with flexible-array member
platform/chrome: cros_ec_commands: Replace zero-length array with flexible-array member
mailbox: zynqmp-ipi-message: Replace zero-length array with flexible-array member
dmaengine: ti-cppi5: Replace zero-length array with flexible-array member
Pull dma-mapping fix from Christoph Hellwig:
"Fix an integer overflow on 32-bit platforms in the new DMA range code
(Geert Uytterhoeven)"
* tag 'dma-mapping-5.10-2' of git://git.infradead.org/users/hch/dma-mapping:
dma-mapping: fix 32-bit overflow with CONFIG_ARM_LPAE=n
Pull SCSI fixes from James Bottomley:
"Four driver fixes and one core fix.
The core fix closes a race window where we could kick off a second
asynchronous scan because the test and set of the variable preventing
it isn't atomic"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: hisi_sas: Stop using queue #0 always for v2 hw
scsi: ibmvscsi: Fix potential race after loss of transport
scsi: mptfusion: Fix null pointer dereferences in mptscsih_remove()
scsi: qla2xxx: Return EBUSY on fcport deletion
scsi: core: Don't start concurrent async scan on same host
Unless we want to test with THP, then we shouldn't require it to be
configured by the host kernel. Unfortunately, even advising with
MADV_NOHUGEPAGE does require it, so check for THP first in order
to avoid madvise failing with EINVAL.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Message-Id: <20201029201703.102716-2-drjones@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It was noticed that evmcs_sanitize_exec_ctrls() is not being executed
nowadays despite the code checking 'enable_evmcs' static key looking
correct. Turns out, static key magic doesn't work in '__init' section
(and it is unclear when things changed) but setup_vmcs_config() is called
only once per CPU so we don't really need it to. Switch to checking
'enlightened_vmcs' instead, it is supposed to be in sync with
'enable_evmcs'.
Opportunistically make evmcs_sanitize_exec_ctrls '__init' and drop unneeded
extra newline from it.
Reported-by: Yang Weijiang <weijiang.yang@intel.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20201014143346.2430936-1-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a regression test for commit 671ddc700f ("KVM: nVMX: Don't leak
L1 MMIO regions to L2").
First, check to see that an L2 guest can be launched with a valid
APIC-access address that is backed by a page of L1 physical memory.
Next, set the APIC-access address to a (valid) L1 physical address
that is not backed by memory. KVM can't handle this situation, so
resuming L2 should result in a KVM exit for internal error
(emulation).
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Ricardo Koller <ricarkol@google.com>
Reviewed-by: Peter Shier <pshier@google.com>
Message-Id: <20201026180922.3120555-1-jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There is a regular need in the kernel to provide a way to declare having a
dynamically sized set of trailing elements in a structure. Kernel code
should always use “flexible array members”[1] for these cases. The
older style of one-element or zero-length arrays should no longer be
used[2].
Refactor the code according to the use of a flexible-array member in
struct gve_stats_report, instead of a zero-length array, and use the
struct_size() helper to calculate the size for the resource allocation.
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.9/process/deprecated.html#zero-length-and-one-element-arrays
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Pull io_uring fixes from Jens Axboe:
- Fixes for linked timeouts (Pavel)
- Set IO_WQ_WORK_CONCURRENT early for async offload (Pavel)
- Two minor simplifications that make the code easier to read and
follow (Pavel)
* tag 'io_uring-5.10-2020-10-30' of git://git.kernel.dk/linux-block:
io_uring: use type appropriate io_kiocb handler for double poll
io_uring: simplify __io_queue_sqe()
io_uring: simplify nxt propagation in io_queue_sqe
io_uring: don't miss setting IO_WQ_WORK_CONCURRENT
io_uring: don't defer put of cancelled ltimeout
io_uring: always clear LINK_TIMEOUT after cancel
io_uring: don't adjust LINK_HEAD in cancel ltimeout
io_uring: remove opcode check on ltimeout kill
Pull libata fix from Jens Axboe:
"Single fix for an old regression with sata_nv"
* tag 'libata-5.10-2020-10-30' of git://git.kernel.dk/linux-block:
ata: sata_nv: Fix retrieving of active qcs
Pull btrfs fixes from David Sterba:
- lockdep fixes:
- drop path locks before manipulating sysfs objects or qgroups
- preliminary fixes before tree locks get switched to rwsem
- use annotated seqlock
- build warning fixes (printk format)
- fix relocation vs fallocate race
- tree checker properly validates number of stripes and parity
- readahead vs device replace fixes
- iomap dio fix for unnecessary buffered io fallback
* tag 'for-5.10-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: convert data_seqcount to seqcount_mutex_t
btrfs: don't fallback to buffered read if we don't need to
btrfs: add a helper to read the tree_root commit root for backref lookup
btrfs: drop the path before adding qgroup items when enabling qgroups
btrfs: fix readahead hang and use-after-free after removing a device
btrfs: fix use-after-free on readahead extent after failure to create it
btrfs: tree-checker: validate number of chunk stripes and parity
btrfs: tree-checker: fix incorrect printk format
btrfs: drop the path before adding block group sysfs files
btrfs: fix relocation failure due to race with fallocate
Pull arm64 fixes from Will Deacon:
"The diffstat is a bit spread out thanks to an invasive CPU erratum
workaround which missed the merge window and also a bunch of fixes to
the recently added MTE selftests.
- Fixes to MTE kselftests
- Fix return code from KVM Spectre-v2 hypercall
- Build fixes for ld.lld and Clang's infamous integrated assembler
- Ensure RCU is up and running before we use printk()
- Workaround for Cortex-A77 erratum 1508412
- Fix linker warnings from unexpected ELF sections
- Ensure PE/COFF sections are 64k aligned"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Change .weak to SYM_FUNC_START_WEAK_PI for arch/arm64/lib/mem*.S
arm64/smp: Move rcu_cpu_starting() earlier
arm64: Add workaround for Arm Cortex-A77 erratum 1508412
arm64: Add part number for Arm Cortex-A77
arm64: mte: Document that user PSTATE.TCO is ignored by kernel uaccess
module: use hidden visibility for weak symbol references
arm64: efi: increase EFI PE/COFF header padding to 64 KB
arm64: vmlinux.lds: account for spurious empty .igot.plt sections
kselftest/arm64: Fix check_user_mem test
kselftest/arm64: Fix check_ksm_options test
kselftest/arm64: Fix check_mmap_options test
kselftest/arm64: Fix check_child_memory test
kselftest/arm64: Fix check_tags_inclusion test
kselftest/arm64: Fix check_buffer_fill test
arm64: avoid -Woverride-init warning
KVM: arm64: ARM_SMCCC_ARCH_WORKAROUND_1 doesn't return SMCCC_RET_NOT_REQUIRED
arm64: vdso32: Allow ld.lld to properly link the VDSO
Pull asm-generic fix from Arnd Bergmann:
"One small bugfix, fixing a build regression for RISC-V"
* tag 'asm-generic-fixes-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic: mark __{get,put}_user_fn as __always_inline
Pull ARM SoC fixes from Arnd Bergmann:
"This is a fairly large set of bug fixes on top of -rc1, as most of
them were ready but didn't quite make it into the last-minute pull
requests for the merge window.
Allwinner:
- fix for incorrect CPU overtemperature limit
Amlogic:
- multiple smaller DT bugfixes, and missing device nodes
Marvell EBU:
- add missing aliases for ethernet switch ports on espressobin board
Marvell MMP:
- DTC warning fix
- bugfix for camera interface power-down
NXP i.MX:
- re-enable the GPIO driver on all defconfigs
ST STM32MP1:
- fix random crashes from incorrect voltage settings
Synaptics Berlin:
- enable the correct hardware timer driver
Texas Instruments K2G:
- fix a boot regression in the power domain code
TEE drivers:
- fix regression in TEE "login" method
SCMI drivers:
- multiple code fixes for corner cases in newly added code
MAINTAINERS file:
- move Kukjin Kim and Sangbeom Kim to credits (used to work on
Samsung Exynos)
- Masahiro Yamada is stepping down as Uniphier maintainer
I did not include a series of patches that work around a regression
caused by a bugfix in an ethernet phy driver that resulted in an
inadvertent DT binding change. This is still under discussion"
* tag 'arm-soc-fixes-v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (31 commits)
soc: ti: ti_sci_pm_domains: check for proper args count in xlate
ARM: dts: stm32: Describe Vin power supply on stm32mp157c-edx board
ARM: dts: stm32: Describe Vin power supply on stm32mp15xx-dkx board
ARM: multi_v5_defconfig: Select CONFIG_GPIO_MXC
ARM: imx_v4_v5_defconfig: Select CONFIG_GPIO_MXC
ARM: dts: mmp2-olpc-xo-1-75: Use plural form of "-gpios"
ARM: dts: mmp3: Add power domain for the camera
arm64: berlin: Select DW_APB_TIMER_OF
dt-bindings: sram: sunxi-sram: add V3s compatible string
MAINTAINERS: Move Sangbeom Kim to credits
MAINTAINERS: Move Kukjin Kim to credits
MAINTAINERS: step down as maintainer of UniPhier SoCs and Denali driver
ARM: multi_v7_defconfig: Build in CONFIG_GPIO_MXC by default
ARM: imx_v6_v7_defconfig: Build in CONFIG_GPIO_MXC by default
arm64: defconfig: Build in CONFIG_GPIO_MXC by default
arm64: dts: meson: odroid-n2 plus: fix vddcpu_a pwm
ARM: dts: meson8: remove two invalid interrupt lines from the GPU node
arm64: dts: amlogic: add missing ethernet reset ID
firmware: arm_scmi: Fix duplicate workqueue name
firmware: arm_scmi: Fix locking in notifications
...
