drivers: soc: TI SOC changes for 5.11
- ti_sci changes towards DMSS support
- Static warning fixes
- Kconfig update for Keystone ARM64 socs
- AM64X SOC family support
To better understand error that can be detected by the DMA controller,
manage the error flags before the transfer flags.
This way, it is possible to know if the FIFO error flag is set for an
over/underrun condition or a FIFO level error.
When a FIFO over/underrun condition occurs, the data is not lost because
peripheral request is not acknowledged by the stream until the over/
underrun condition is cleared. If this acknowledge takes too much time,
the peripheral itself may detect an over/underrun condition of its internal
buffer and data might be lost.
That's why in case the FIFO error flag is set, we check if the channel is
disabled or not, and if a Transfer Complete flag is set, which means that
the channel is disabled because of the end of transfer.
Because channel is disabled by hardware either by a FIFO level error, or by
an end of transfer.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20201120143320.30367-2-amelie.delaunay@st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
While performing suspend/resume, we were getting below kernel crash.
[ 54.541672] [FTS][Info]gesture suspend...
[ 54.605256] [FTS][Error][GESTURE]Enter into gesture(suspend) failed!
[ 54.605256]
[ 58.345850] irq event 10: bogus return value fffffff3
......
[ 58.345966] [<ffff0000080830f0>] el1_irq+0xb0/0x124
[ 58.345971] [<ffff000008085360>] arch_cpu_idle+0x10/0x18
[ 58.345975] [<ffff0000081077f4>] do_idle+0x1ac/0x1e0
[ 58.345979] [<ffff0000081079c8>] cpu_startup_entry+0x20/0x28
[ 58.345983] [<ffff000008a80ed0>] rest_init+0xd0/0xdc
[ 58.345988] [<ffff0000091c0b48>] start_kernel+0x390/0x3a4
[ 58.345990] handlers:
[ 58.345994] [<ffff0000085120d0>] bam_dma_irq
The reason for the crash we found is, bam_dma_irq() was returning
negative value when the device resumes in some conditions.
In addition, the irq handler should have one of the below return values.
IRQ_NONE interrupt was not from this device or was not handled
IRQ_HANDLED interrupt was handled by this device
IRQ_WAKE_THREAD handler requests to wake the handler thread
Therefore, to resolve this crash, we have changed the return value to
IRQ_NONE.
Signed-off-by: Parth Y Shah <sparth1292@gmail.com>
Link: https://lore.kernel.org/r/1607322820-7450-1-git-send-email-sparth1292@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support to allow configuration of Intel Analytics Accelerator (IAX) in
addition to the Intel Data Streaming Accelerator (DSA). The IAX hardware
has the same configuration interface as DSA. The main difference
is the type of operations it performs. We can support the DSA and
IAX devices on the same driver with some tweaks.
IAX has a 64B completion record that needs to be 64B aligned, as opposed to
a 32B completion record that is 32B aligned for DSA. IAX also does not
support token management.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/160564555488.1834439.4261958859935360473.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Update the kerneldoc function headers to fix build warnings:
drivers/dma/qcom/qcom_adm.c:180: warning: Function parameter or member 'chan' not described in 'adm_free_chan'
drivers/dma/qcom/qcom_adm.c:190: warning: Function parameter or member 'burst' not described in 'adm_get_blksize'
drivers/dma/qcom/qcom_adm.c:466: warning: Function parameter or member 'chan' not described in 'adm_terminate_all'
drivers/dma/qcom/qcom_adm.c:466: warning: Excess function parameter 'achan' description in 'adm_terminate_all'
drivers/dma/qcom/qcom_adm.c:503: warning: Function parameter or member 'achan' not described in 'adm_start_dma'
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Link: https://lore.kernel.org/r/20201126184602.GA1008@earth.li
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver can match only via the DT table so the main table should be
always used and the of_match_ptr does not have any sense (this also
allows ACPI matching via PRP0001, even though it is not relevant here).
The secondary match of_device_id tables (passed to of_match_node) should
be marked as maybe unused to fix compile testing (!CONFIG_OF on x86_64)
warnings:
drivers/dma/ti/dma-crossbar.c:125:34: warning:
‘ti_am335x_master_match’ defined but not used [-Wunused-const-variable=]
drivers/dma/ti/dma-crossbar.c:22:34: warning:
‘ti_dma_xbar_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201120162303.482126-6-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver uses a second of_device_id table in the probe()
function by passing it to of_match_node(). This code will be a no-op
for compile testing (!CONFIG_OF on x86_64):
drivers/dma/stm32-dmamux.c:171:34: warning:
‘stm32_stm32dma_master_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201120162303.482126-5-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/dma/sf-pdma/sf-pdma.c:576:34: warning:
‘sf_pdma_dt_ids’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201120162303.482126-4-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/dma/mv_xor.c:1281:34: warning:
‘mv_xor_dt_ids’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201120162303.482126-3-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/dma/dw-axi-dmac/dw-axi-dmac-platform.c:984:34: warning:
‘dw_dma_of_id_table’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201120162303.482126-2-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/dma/dma-jz4780.c:1031:34: warning:
‘jz4780_dma_dt_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201120162303.482126-1-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This controller provides DMAengine capabilities for a variety of peripheral
buses such as I2C, UART, and SPI. By using GPI dmaengine driver, bus
drivers can use a standardize interface that is protocol independent to
transfer data between memory and peripheral.
Link: https://lore.kernel.org/r/20201109085450.24843-4-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add the DMA engine driver for the QCOM Application Data Mover (ADM) DMA
controller found in the MSM8x60 and IPQ/APQ8064 platforms.
The ADM supports both memory to memory transactions and memory
to/from peripheral device transactions. The controller also provides
flow control capabilities for transactions to/from peripheral devices.
The initial release of this driver supports slave transfers to/from
peripherals and also incorporates CRCI (client rate control interface)
flow control.
The hardware only supports a 32 bit physical address, so specifying
!PHYS_ADDR_T_64BIT gives maximum COMPILE_TEST coverage without having to
spend effort on kludging things in the code that will never actually be
needed on real hardware.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Thomas Pedersen <twp@codeaurora.org>
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Link: https://lore.kernel.org/r/20201114140233.GM32650@earth.li
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The patch fix two reference leak.
1) pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to call put operation will result in
reference leak.
2) The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced.
We fix it by: 1) adding call pm_runtime_put_noidle or
pm_runtime_put_sync in error handling. 2) adding pm_runtime_disable
in error handling, to keep usage counter and disable depth balanced.
Fixes: 88139ed030 ("soc: ti: add Keystone Navigator DMA support")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Since the of_device_get_match_data() doesn't return error code, remove
wrong IS_ERR test. Proper check against NULL pointer is already done
later before usage: if (data && data->...).
Additionally, proceeding with empty device data is valid (e.g. in case
of "ti,am3356-pruss").
Reported-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
With the integration of chip-id detection scheme in kernel[1], there
is no specific need to maintain multitudes of SoC specific config
options, discussed as per [2], we have deprecated the usage in other
places for v5.10-rc1. Drop the configuration for the follow on kernel.
[1] drivers/soc/ti/k3-socinfo.c commit 907a2b7e2f ("soc: ti: add k3 platforms chipid module driver")
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/soc/ti/k3-ringacc.c:163: warning: Function parameter or member 'state' not described in 'k3_ring'
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/soc/ti/wkup_m3_ipc.c:227: warning: Function parameter or member 'm3_ipc' not described in 'wkup_m3_set_mem_type'
drivers/soc/ti/wkup_m3_ipc.c:236: warning: Function parameter or member 'm3_ipc' not described in 'wkup_m3_set_resume_address'
drivers/soc/ti/wkup_m3_ipc.c:248: warning: Function parameter or member 'm3_ipc' not described in 'wkup_m3_request_pm_status'
drivers/soc/ti/wkup_m3_ipc.c:268: warning: Function parameter or member 'm3_ipc' not described in 'wkup_m3_prepare_low_power'
drivers/soc/ti/wkup_m3_ipc.c:322: warning: Function parameter or member 'm3_ipc' not described in 'wkup_m3_finish_low_power'
drivers/soc/ti/wkup_m3_ipc.c:369: warning: Function parameter or member 'm3_ipc' not described in 'wkup_m3_set_rtc_only'
drivers/soc/ti/wkup_m3_ipc.c:369: warning: Excess function parameter 'wkup_m3_wakeup' description in 'wkup_m3_set_rtc_only'
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/soc/ti/pm33xx.c: In function ‘am33xx_do_sram_idle’:
drivers/soc/ti/pm33xx.c:138:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/soc/ti/knav_dma.c:507: warning: Function parameter or member 'channel' not described in 'knav_dma_close_channel'
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: Sandeep Nair <sandeep_n@ti.com>
Cc: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/soc/ti/knav_qmss_queue.c:528: warning: Function parameter or member 'flags' not described in 'knav_queue_open'
drivers/soc/ti/knav_qmss_queue.c:528: warning: Function parameter or member 'id' not described in 'knav_queue_open'
drivers/soc/ti/knav_qmss_queue.c:528: warning: Function parameter or member 'name' not described in 'knav_queue_open'
drivers/soc/ti/knav_qmss_queue.c:551: warning: Excess function parameter 'qh' description in 'knav_queue_close'
drivers/soc/ti/knav_qmss_queue.c:551: warning: Function parameter or member 'qhandle' not described in 'knav_queue_close'
drivers/soc/ti/knav_qmss_queue.c:583: warning: Excess function parameter 'qh' description in 'knav_queue_device_control'
drivers/soc/ti/knav_qmss_queue.c:583: warning: Function parameter or member 'arg' not described in 'knav_queue_device_control'
drivers/soc/ti/knav_qmss_queue.c:583: warning: Function parameter or member 'cmd' not described in 'knav_queue_device_control'
drivers/soc/ti/knav_qmss_queue.c:583: warning: Function parameter or member 'qhandle' not described in 'knav_queue_device_control'
drivers/soc/ti/knav_qmss_queue.c:635: warning: Excess function parameter 'data' description in 'knav_queue_push'
drivers/soc/ti/knav_qmss_queue.c:635: warning: Excess function parameter 'qh' description in 'knav_queue_push'
drivers/soc/ti/knav_qmss_queue.c:635: warning: Function parameter or member 'dma' not described in 'knav_queue_push'
drivers/soc/ti/knav_qmss_queue.c:635: warning: Function parameter or member 'flags' not described in 'knav_queue_push'
drivers/soc/ti/knav_qmss_queue.c:635: warning: Function parameter or member 'qhandle' not described in 'knav_queue_push'
drivers/soc/ti/knav_qmss_queue.c:635: warning: Function parameter or member 'size' not described in 'knav_queue_push'
drivers/soc/ti/knav_qmss_queue.c:655: warning: Excess function parameter 'qh' description in 'knav_queue_pop'
drivers/soc/ti/knav_qmss_queue.c:655: warning: Function parameter or member 'qhandle' not described in 'knav_queue_pop'
drivers/soc/ti/knav_qmss_queue.c:655: warning: Function parameter or member 'size' not described in 'knav_queue_pop'
drivers/soc/ti/knav_qmss_queue.c:759: warning: Function parameter or member 'name' not described in 'knav_pool_create'
drivers/soc/ti/knav_qmss_queue.c:759: warning: Function parameter or member 'num_desc' not described in 'knav_pool_create'
drivers/soc/ti/knav_qmss_queue.c:759: warning: Function parameter or member 'region_id' not described in 'knav_pool_create'
drivers/soc/ti/knav_qmss_queue.c:862: warning: Excess function parameter 'pool' description in 'knav_pool_destroy'
drivers/soc/ti/knav_qmss_queue.c:862: warning: Function parameter or member 'ph' not described in 'knav_pool_destroy'
drivers/soc/ti/knav_qmss_queue.c:892: warning: Excess function parameter 'pool' description in 'knav_pool_desc_get'
drivers/soc/ti/knav_qmss_queue.c:892: warning: Function parameter or member 'ph' not described in 'knav_pool_desc_get'
drivers/soc/ti/knav_qmss_queue.c:911: warning: Excess function parameter 'pool' description in 'knav_pool_desc_put'
drivers/soc/ti/knav_qmss_queue.c:911: warning: Function parameter or member 'desc' not described in 'knav_pool_desc_put'
drivers/soc/ti/knav_qmss_queue.c:911: warning: Function parameter or member 'ph' not described in 'knav_pool_desc_put'
drivers/soc/ti/knav_qmss_queue.c:931: warning: Excess function parameter 'pool' description in 'knav_pool_desc_map'
drivers/soc/ti/knav_qmss_queue.c:931: warning: Function parameter or member 'desc' not described in 'knav_pool_desc_map'
drivers/soc/ti/knav_qmss_queue.c:931: warning: Function parameter or member 'dma' not described in 'knav_pool_desc_map'
drivers/soc/ti/knav_qmss_queue.c:931: warning: Function parameter or member 'dma_sz' not described in 'knav_pool_desc_map'
drivers/soc/ti/knav_qmss_queue.c:931: warning: Function parameter or member 'ph' not described in 'knav_pool_desc_map'
drivers/soc/ti/knav_qmss_queue.c:931: warning: Function parameter or member 'size' not described in 'knav_pool_desc_map'
drivers/soc/ti/knav_qmss_queue.c:956: warning: Excess function parameter 'pool' description in 'knav_pool_desc_unmap'
drivers/soc/ti/knav_qmss_queue.c:956: warning: Function parameter or member 'dma' not described in 'knav_pool_desc_unmap'
drivers/soc/ti/knav_qmss_queue.c:956: warning: Function parameter or member 'dma_sz' not described in 'knav_pool_desc_unmap'
drivers/soc/ti/knav_qmss_queue.c:956: warning: Function parameter or member 'ph' not described in 'knav_pool_desc_unmap'
drivers/soc/ti/knav_qmss_queue.c:975: warning: Excess function parameter 'pool' description in 'knav_pool_count'
drivers/soc/ti/knav_qmss_queue.c:975: warning: Function parameter or member 'ph' not described in 'knav_pool_count'
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: Sandeep Nair <sandeep_n@ti.com>
Cc: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/soc/ti/knav_qmss_queue.c: In function ‘knav_setup_queue_pools’:
drivers/soc/ti/knav_qmss_queue.c:1310:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: Sandeep Nair <sandeep_n@ti.com>
Cc: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
If a rstctrl reset bit is already deasserted, we can just bail out early
not wait for rstst to clear. Otherwise we can have deassert fail for
already deasserted resets.
Fixes: c5117a78dd ("soc: ti: omap-prm: poll for reset complete during de-assert")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to pm_runtime_put_noidle will result in
reference leak in knav_queue_probe, so we should fix it.
Fixes: 41f93af900 ("soc: ti: add Keystone Navigator QMSS driver")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
