There are a few differences in the power on/off functions between PCIE
and USB. The changes in the power off function in particular are needed
for the RTL8832CU to be able to power on again after it's powered off.
While the RTL8832CU appears to work without the changes in the power on
function, it's probably best to implement them, in case they are needed
in some situations.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/598dec66-b5cc-435a-bcf6-fa66577f8cfc@gmail.com
RTL8852AU, RTL8852CU, and RTL8922AU will need a different TX channel
to bulk out endpoint mapping, so create a new struct rtw89_usb_info
and move the mapping there. Initialise it in each chip's driver.
Struct rtw89_usb_info will also hold some registers which are located
at different offsets in RTL8852CU compared to the other wifi 6 chips.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/de11cfae-1dc0-4514-95b2-02b1bbfa92be@gmail.com
Reduce scan time for all supported channels from 4.4s to 3.5s.
If NL80211_SCAN_FLAG_COLOCATED_6GHZ is set in scan request, only scan PSC
channels and the channels from the RNR element found on the 2.4/5 GHz
channels. When firmware support parsing RNR element from received beacon
or probe response, offload the decision about non-PSC channels to firmware.
Driver do not need to fill non-PSC channels to scan list. If
NL80211_SCAN_FLAG_COLOCATED_6GHZ is not set, scan all supported channels.
Signed-off-by: Jui-Peng Tsai <emma_tsai@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20251021133402.15467-9-pkshih@realtek.com
Somehow power-save related functions get failure, such as failed to
send null packet, or no response form firmware, and then WiFi will
become unstable. Trigger SER function actively to reset firmware/driver
to recover from abnormal states, including
- firmware failed to ACK for entering PS mode
- firmware failed to ACK for leaving PS mode
- check PS H2C command received by firmware fail
- failed to leave PS state
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20251021133402.15467-8-pkshih@realtek.com
To switch link, FW needs H2C commands to indicate which link is on or off.
Originally, these H2C commands are considered only when the link switching
is initiated by driver. But, in some cases, e.g. ml_reconf or TTLM, link
switching would be initiated by stack. Hence, plan these H2C commands into
ieee80211_ops.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20251021133402.15467-4-pkshih@realtek.com
RX task enqueues C2H events and fork a C2H work to handle events, but
the work uses skb_queue_walk_safe() without a lock causing potential
racing. Use skb_queue_splice() and its friends with spin_lock to splice
the queue to local, and then still use skb_queue_walk_safe() to iterate
all events.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20251021133402.15467-2-pkshih@realtek.com
RTL8192CU disappears and reappears when rtl8xxxu is unloaded:
usbcore: deregistering interface driver rtl8xxxu
wlp3s0f3u2: deauthenticating from ... by local choice (Reason: 3=DEAUTH_LEAVING)
usb 1-2: rtl8xxxu_active_to_emu: Disabling MAC timed out
usb 1-2: USB disconnect, device number 7
usb 1-2: disconnecting
usb 1-2: new high-speed USB device number 8 using xhci_hcd
usb 1-2: New USB device found, idVendor=0bda, idProduct=8178, bcdDevice= 2.00
usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-2: Product: 802.11n WLAN Adapter
usb 1-2: Manufacturer: Realtek
usb 1-2: SerialNumber: 00e04c000001
This is because rtl8xxxu is using the power off sequence for RTL8723AU.
Add the correct power off sequence for RTL8192CU.
rtl8xxxu_power_off(), rtl8xxxu_active_to_emu(), and
rtl8xxxu_emu_to_disabled() are now only used for RTL8723AU, so move
them to 8723a.c and rename them to have the "rtl8723au" prefix.
Tested only with RTL8192CU.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/b9d3f137-12ce-4bd9-8ada-3b8874bc3615@gmail.com
Someone reported a problem with their TP-Link WN722N (RTL8188EUS):
usb 1-1: This Realtek USB WiFi dongle (0x2357:0x010c) is untested!
usb 1-1: Please report results to Jes.Sorensen@gmail.com
usb 1-1: Fatal - failed to parse EFuse
rtl8xxxu: probe of 1-1:1.0 failed with error -22
This error can happen when the first two bytes of the efuse don't have
the expected magic value of 0x8129. In a situation like this it could
be useful to see the contents of the efuse.
Dump the efuse right after reading it, before trying to parse it.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/1f544dc4-17f6-4401-995d-5cb4567b82fa@gmail.com
Pull networking fixes from Paolo Abeni:
"Including fixes from CAN
Current release - regressions:
- udp: do not use skb_release_head_state() before
skb_attempt_defer_free()
- gro_cells: use nested-BH locking for gro_cell
- dpll: zl3073x: increase maximum size of flash utility
Previous releases - regressions:
- core: fix lockdep splat on device unregister
- tcp: fix tcp_tso_should_defer() vs large RTT
- tls:
- don't rely on tx_work during send()
- wait for pending async decryptions if tls_strp_msg_hold fails
- can: j1939: add missing calls in NETDEV_UNREGISTER notification
handler
- eth: lan78xx: fix lost EEPROM write timeout in
lan78xx_write_raw_eeprom
Previous releases - always broken:
- ip6_tunnel: prevent perpetual tunnel growth
- dpll: zl3073x: handle missing or corrupted flash configuration
- can: m_can: fix pm_runtime and CAN state handling
- eth:
- ixgbe: fix too early devlink_free() in ixgbe_remove()
- ixgbevf: fix mailbox API compatibility
- gve: Check valid ts bit on RX descriptor before hw timestamping
- idpf: cleanup remaining SKBs in PTP flows
- r8169: fix packet truncation after S4 resume on RTL8168H/RTL8111H"
* tag 'net-6.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (50 commits)
udp: do not use skb_release_head_state() before skb_attempt_defer_free()
net: usb: lan78xx: fix use of improperly initialized dev->chipid in lan78xx_reset
netdevsim: set the carrier when the device goes up
selftests: tls: add test for short splice due to full skmsg
selftests: net: tls: add tests for cmsg vs MSG_MORE
tls: don't rely on tx_work during send()
tls: wait for pending async decryptions if tls_strp_msg_hold fails
tls: always set record_type in tls_process_cmsg
tls: wait for async encrypt in case of error during latter iterations of sendmsg
tls: trim encrypted message to match the plaintext on short splice
tg3: prevent use of uninitialized remote_adv and local_adv variables
MAINTAINERS: new entry for IPv6 IOAM
gve: Check valid ts bit on RX descriptor before hw timestamping
net: core: fix lockdep splat on device unregister
MAINTAINERS: add myself as maintainer for b53
selftests: net: check jq command is supported
net: airoha: Take into account out-of-order tx completions in airoha_dev_xmit()
tcp: fix tcp_tso_should_defer() vs large RTT
r8152: add error handling in rtl8152_driver_init
usbnet: Fix using smp_processor_id() in preemptible code warnings
...
Pull ata fix from Niklas Cassel:
- Do not print an error message (and assume that the General Purpose
Log Directory log page is not supported) for a device that reports a
bogus General Purpose Logging Version.
Unsurprisingly, many vendors fail to report the only valid General
Purpose Logging Version (Damien)
* tag 'ata-6.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux:
ata: libata-core: relax checks in ata_read_log_directory()
To adapt to new firmware for AML devices, the driver should send the
"SET_LINK_CMD" to the firmware only once when switching PHY interface
mode, and no longer needs to re-trigger PHY configuration based on the
RX signal interrupt (TXGBE_GPIOBIT_3).
In previous firmware versions, the PHY was configured only after receiving
"SET_LINK_CMD", and might remain incomplete if the RX signal was lost.
To handle this case, the driver used TXGBE_GPIOBIT_3 interrupt to resend
the command. This workaround is no longer necessary with the new firmware.
And the unknown link speed is permitted in the mailbox buffer.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://patch.msgid.link/20251014061726.36660-3-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Recent firmware updates introduce additional fields in the mailbox message
to provide more information for identifying 40G and 100G QSFP modules.
To accommodate these new fields, expand the mailbox buffer size by 4 bytes.
Without this change, drivers built against the updated firmware cannot
properly identify modules due to mismatched mailbox message lengths.
The old firmware version that used the smaller mailbox buffer has never
been publicly released, so there are no backward-compatibility concerns.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251014061726.36660-2-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The HW always works on a 4K page size. When the OS supports larger
pages, we fragment them across multiple BDQ descriptors.
We were not properly incrementing the descriptor, which resulted in us
specifying the last chunks id/addr and then 15 zero descriptors. This
would cause packet loss and driver crashes. This is not a fix since the
Kconfig prevents use outside of x86.
Signed-off-by: Dimitri Daskalakis <dimitri.daskalakis1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251013211449.1377054-2-dimitri.daskalakis1@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
dev->chipid is used in lan78xx_init_mac_address before it's initialized:
lan78xx_reset() {
lan78xx_init_mac_address()
lan78xx_read_eeprom()
lan78xx_read_raw_eeprom() <- dev->chipid is used here
dev->chipid = ... <- dev->chipid is initialized correctly here
}
Reorder initialization so that dev->chipid is set before calling
lan78xx_init_mac_address().
Fixes: a0db7d10b7 ("lan78xx: Add to handle mux control per chip id")
Signed-off-by: I Viswanath <viswanathiyyappan@gmail.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Khalid Aziz <khalid@kernel.org>
Link: https://patch.msgid.link/20251013181648.35153-1-viswanathiyyappan@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Marc Kleine-Budde says:
====================
pull-request: can 2025-10-14
The first 2 paches are by Celeste Liu and target the gS_usb driver.
The first patch remove the limitation to 3 CAN interface per USB
device. The second patch adds the missing population of
net_device->dev_port.
The next 4 patches are by me and fix the m_can driver. They add a
missing pm_runtime_disable(), fix the CAN state transition back to
Error Active and fix the state after ifup and suspend/resume.
Another patch by me targets the m_can driver, too and replaces Dong
Aisheng's old email address.
The next 2 patches are by Vincent Mailhol and update the CAN
networking Documentation.
Tetsuo Handa contributes the last patch that add missing cleanup calls
in the NETDEV_UNREGISTER notification handler.
* tag 'linux-can-fixes-for-6.18-20251014' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: j1939: add missing calls in NETDEV_UNREGISTER notification handler
can: add Transmitter Delay Compensation (TDC) documentation
can: remove false statement about 1:1 mapping between DLC and length
can: m_can: replace Dong Aisheng's old email address
can: m_can: fix CAN state in system PM
can: m_can: m_can_chip_config(): bring up interface in correct state
can: m_can: m_can_handle_state_errors(): fix CAN state transition to Error Active
can: m_can: m_can_plat_remove(): add missing pm_runtime_disable()
can: gs_usb: gs_make_candev(): populate net_device->dev_port
can: gs_usb: increase max interface to U8_MAX
====================
Link: https://patch.msgid.link/20251014122140.990472-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kory Maincent says:
====================
Preserve PSE PD692x0 configuration across reboots
Previously, the driver would always reconfigure the PSE hardware on
probe, causing a port matrix reflash that resulted in temporary power
loss to all connected devices. This change maintains power continuity
by preserving existing configuration when the PSE has been previously
initialized.
====================
Link: https://patch.msgid.link/20251013-feature_pd692x0_reboot_keep_conf-v2-0-68ab082a93dd@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Detect when PSE hardware is already configured (user byte == 42) and
skip hardware initialization to prevent power interruption to connected
devices during system reboots.
Previously, the driver would always reconfigure the PSE hardware on
probe, causing a port matrix reflash that resulted in temporary power
loss to all connected devices. This change maintains power continuity
by preserving existing configuration when the PSE has been previously
initialized.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251013-feature_pd692x0_reboot_keep_conf-v2-3-68ab082a93dd@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cache the port matrix configuration in driver private data to enable
PSE controller reconfiguration. This refactoring separates device tree
parsing from hardware configuration application, allowing settings to be
reapplied without reparsing the device tree.
This refactoring is a prerequisite for preserving PSE configuration
across reboots to prevent power disruption to connected devices.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251013-feature_pd692x0_reboot_keep_conf-v2-2-68ab082a93dd@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bringing a linked netdevsim device down and then up causes communication
failure because both interfaces lack carrier. Basically a ifdown/ifup on
the interface make the link broken.
Commit 3762ec05a9 ("netdevsim: add NAPI support") added supported
for NAPI, calling netif_carrier_off() in nsim_stop(). This patch
re-enables the carrier symmetrically on nsim_open(), in case the device
is linked and the peer is up.
Signed-off-by: Breno Leitao <leitao@debian.org>
Fixes: 3762ec05a9 ("netdevsim: add NAPI support")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251014-netdevsim_fix-v2-1-53b40590dae1@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Sabrina Dubroca says:
====================
tls: misc bugfixes
Jann Horn reported multiple bugs in kTLS. This series addresses them,
and adds some corresponding selftests for those that are reproducible
(and without failure injection).
====================
Link: https://patch.msgid.link/cover.1760432043.git.sd@queasysnail.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With async crypto, we rely on tx_work to actually transmit records
once encryption completes. But while send() is running, both the
tx_lock and socket lock are held, so tx_work_handler cannot process
the queue of encrypted records, and simply reschedules itself. During
a large send(), this could last a long time, and use a lot of memory.
Transmit any pending encrypted records before restarting the main
loop of tls_sw_sendmsg_locked.
Fixes: a42055e8d2 ("net/tls: Add support for async encryption of records for performance")
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://patch.msgid.link/8396631478f70454b44afb98352237d33f48d34d.1760432043.git.sd@queasysnail.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
