When setting a new bitrate, WMI peer association command is sent from
the host without the peer authentication bit set in peer_flags for
security mode, which causes ping failure.
The firmware handles peer_flags when the client is associating, as the
peer authentication bit in peer_flags is set after the key exchange.
When the WMI peer association command is sent from the host to update
the new bitrate for an associated STA, the firmware expects the WMI
peer authentication bit to be set in peer_flags.
Fix this issue by ensuring that the WMI peer auth bit is set in
peer_flags in WMI peer association command when updating the new
bitrate.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Thiraviyam Mariyappan <thiraviyam.mariyappan@oss.qualcomm.com>
Signed-off-by: Ramasamy Kaliappan <ramasamy.kaliappan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250608145651.1735236-1-ramasamy.kaliappan@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add the missing memory barrier to make sure that LMAC source ring
descriptors are written before updating the head pointer to avoid
passing stale data to the firmware on weakly ordered architectures like
aarch64.
Note that non-LMAC rings use MMIO write accessors which have the
required write memory barrier.
Tested-on: WCN7850 hw2.0 WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Cc: stable@vger.kernel.org # 6.3
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250617084402.14475-4-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add the missing memory barrier to make sure that destination ring
descriptors are read after the head pointers to avoid using stale data
on weakly ordered architectures like aarch64.
The barrier is added to the ath12k_hal_srng_access_begin() helper for
symmetry with follow-on fixes for source ring buffer corruption which
will add barriers to ath12k_hal_srng_access_end().
Tested-on: WCN7850 hw2.0 WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Cc: stable@vger.kernel.org # 6.3
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250617084402.14475-2-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add the missing memory barrier to make sure that LMAC source ring
descriptors are written before updating the head pointer to avoid
passing stale data to the firmware on weakly ordered architectures like
aarch64.
Note that non-LMAC rings use MMIO write accessors which have the
required write memory barrier.
Tested-on: WCN6855 hw2.1 WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Cc: stable@vger.kernel.org # 5.6
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250604143457.26032-5-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add the missing memory barrier to make sure that destination ring
descriptors are read after the head pointers to avoid using stale data
on weakly ordered architectures like aarch64.
The barrier is added to the ath11k_hal_srng_access_begin() helper for
symmetry with follow-on fixes for source ring buffer corruption which
will add barriers to ath11k_hal_srng_access_end().
Tested-on: WCN6855 hw2.1 WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Cc: stable@vger.kernel.org # 5.6
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250604143457.26032-2-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The power value is 6 dBm on an AP operating on the 6 GHz channel.
This is a very low value.
On 6 GHz, the target computes the EIRP based on the power values sent
in the WMI_VDEV_SET_TPC_POWER_CMD. Currently, this is being sent only
for station interfaces and not for AP interfaces.
Therefore, add AP vdev to the condition in
ath12k_mac_station_supports_tpc() and rename
ath12k_mac_station_supports_tpc() to ath12k_mac_supports_tpc().
For a AP vdev, hardcode ap_power_type as IEEE80211_REG_LPI_AP, which is
filled in the WMI_VDEV_SET_TPC_POWER_CMDID sent to the target.
Currently, LPI is the only supported AP power mode. Since there is
no method currently to set the AP power mode from user-space, the
power mode is hard-coded to LPI.
Retain the existing logic for populating the power mode for a station
vdev.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Hariharan Basuthkar <quic_hbasuthk@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250606112316.39316-1-quic_hbasuthk@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When both AP/STA and monitor interfaces are enabled, ieee80211_tx_status()
is invoked from two paths: the TX completion handler for data frames
and the WMI TX completion handler for management frames.
In the data path, the skb->cb is properly zeroed using memset, but in
the WMI path, this step is missing.
As a result, mac80211 encountered uninitialized (junk) values in
skb->cb when generating the radiotap header for monitor mode, leading
to invalid radiotap lengths.
Hence, explicitly zero the status field in the skb->cb using memset
in WMI TX completion path to ensure consistent and correct behavior
during WMI tx completion path.
Additionally, set info->status.rates[0].idx = -1 to indicate that
no valid rate information is available, avoiding misinterpretation of
garbage values.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sarika Sharma <quic_sarishar@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250603063512.1887652-1-quic_sarishar@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, when a station is associated with a Non-Transmitting BSS of an
MBSSID set, beacons are not frequently received from the firmware. This
results in missing events via beacons, such as channel switches, leading
to the station not switching to new channel as the AP does, eventually
causing a kick out event from the firmware. This issue arises due to
missing configuration of Non-Transmitting BSS information in station's
vdev up command.
Fix this by filling information such as the Transmitting BSSID, profile index
and profile count in vdev up command of station.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250530035615.3178480-3-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
ath12k station is unable to associate with non-transmitting BSSes
in a Multiple BSS set because the user-space does not receive
information about the non-transmitting BSSes from mac80211's
scan results.
The ath12k driver does not advertise its MBSSID capability to mac80211,
resulting in wiphy->support_mbssid not being set. Consequently, the
information about non-transmitting BSS is not parsed from received
Beacon/Probe response frames and is therefore not included in the
scan results.
Fix this by advertising the MBSSID capability of ath12k driver to
mac80211.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Signed-off-by: Hari Chandrakanthan <quic_haric@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250530035615.3178480-2-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
At present, the ATH12K_DEFAULT_NOISE_FLOOR (-95) is used to calculate RSSI
value, providing an estimated noise floor value. Consequently, the RSSI
value is also approximate. This works but however, using actual noise floor
value will enable the reporting of the true RSSI value.
The firmware possesses the necessary data to determine the actual noise
floor. This data is provided to the host via the WMI event
WMI_PDEV_RSSI_DBM_CONVERSION_PARAMS_INFO_EVENTID, which includes the
runtime parameters needed for calculating the real noise floor in dBm. This
event is triggered by the firmware during channel changes, temperature
offset adjustments, and hardware chainmask modifications. The individual
TLVs may not always be present in each event. For instance, temperature
information might only appear if there is a change in offset due to
temperature variation.
Add support to handle and parse this WMI event. Use the received values to
calculate and store the noise floor value.
A subsequent change will use this noise floor value in the actual RSSI
calculation.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Co-developed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250623-support_real_noise_floor-v2-1-974bbafa317e@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In a number of cases we see kernel panics on resume due
to ath11k kernel page fault, which happens under the
following circumstances:
1) First ath11k_hal_dump_srng_stats() call
Last interrupt received for each group:
ath11k_pci 0000:01:00.0: group_id 0 22511ms before
ath11k_pci 0000:01:00.0: group_id 1 14440788ms before
[..]
ath11k_pci 0000:01:00.0: failed to receive control response completion, polling..
ath11k_pci 0000:01:00.0: Service connect timeout
ath11k_pci 0000:01:00.0: failed to connect to HTT: -110
ath11k_pci 0000:01:00.0: failed to start core: -110
ath11k_pci 0000:01:00.0: firmware crashed: MHI_CB_EE_RDDM
ath11k_pci 0000:01:00.0: already resetting count 2
ath11k_pci 0000:01:00.0: failed to wait wlan mode request (mode 4): -110
ath11k_pci 0000:01:00.0: qmi failed to send wlan mode off: -110
ath11k_pci 0000:01:00.0: failed to reconfigure driver on crash recovery
[..]
2) At this point reconfiguration fails (we have 2 resets) and
ath11k_core_reconfigure_on_crash() calls ath11k_hal_srng_deinit()
which destroys srng lists. However, it does not reset per-list
->initialized flag.
3) Second ath11k_hal_dump_srng_stats() call sees stale ->initialized
flag and attempts to dump srng stats:
Last interrupt received for each group:
ath11k_pci 0000:01:00.0: group_id 0 66785ms before
ath11k_pci 0000:01:00.0: group_id 1 14485062ms before
ath11k_pci 0000:01:00.0: group_id 2 14485062ms before
ath11k_pci 0000:01:00.0: group_id 3 14485062ms before
ath11k_pci 0000:01:00.0: group_id 4 14780845ms before
ath11k_pci 0000:01:00.0: group_id 5 14780845ms before
ath11k_pci 0000:01:00.0: group_id 6 14485062ms before
ath11k_pci 0000:01:00.0: group_id 7 66814ms before
ath11k_pci 0000:01:00.0: group_id 8 68997ms before
ath11k_pci 0000:01:00.0: group_id 9 67588ms before
ath11k_pci 0000:01:00.0: group_id 10 69511ms before
BUG: unable to handle page fault for address: ffffa007404eb010
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 100000067 P4D 100000067 PUD 10022d067 PMD 100b01067 PTE 0
Oops: 0000 [#1] PREEMPT SMP NOPTI
RIP: 0010:ath11k_hal_dump_srng_stats+0x2b4/0x3b0 [ath11k]
Call Trace:
<TASK>
? __die_body+0xae/0xb0
? page_fault_oops+0x381/0x3e0
? exc_page_fault+0x69/0xa0
? asm_exc_page_fault+0x22/0x30
? ath11k_hal_dump_srng_stats+0x2b4/0x3b0 [ath11k (HASH:6cea 4)]
ath11k_qmi_driver_event_work+0xbd/0x1050 [ath11k (HASH:6cea 4)]
worker_thread+0x389/0x930
kthread+0x149/0x170
Clear per-list ->initialized flag in ath11k_hal_srng_deinit().
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Fixes: 5118935b1b ("ath11k: dump SRNG stats during FW assert")
Link: https://patch.msgid.link/20250612084551.702803-1-senozhatsky@chromium.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Introduce 'firmware-name' property to allow end-users and/or integrators to
decide which usecase-specific firmware to run on the WCN6855. This is
necessary due to resource limitations such as memory capacity and CPU
capability, or performance and power optimization for different application
scenarios.
Currently, there are two firmwares, both files can be executed
interchangeably.
For example:
- ath11k/WCN6855/hw2.0/amss.bin,
ath11k/WCN6855/hw2.0/m3.bin
ath11k/WCN6855/hw2.0/board-2.bin
- ath11k/WCN6855/hw2.0/nfa765/amss.bin,
ath11k/WCN6855/hw2.0/nfa765/m3.bin
ath11k/WCN6855/hw2.0/board-2.bin
The former is the default firmware, suitable for most WiFi 6 STA functions.
The latter adds support for commercial-quality SAP and optimizes power
consumption for IoT applications. And both use the same BDF/regdb data
within the main board-2.bin.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-04479-QCAHSPSWPL_V1_V2_SILICONZ_IOE-1
Signed-off-by: Miaoqing Pan <miaoqing.pan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250522013444.1301330-3-miaoqing.pan@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Introduce 'firmware-name' property to allow end-users and/or integrators
to decide which usecase-specific firmware to run on the WCN6855. This is
necessary due to resource limitations such as memory capacity and
CPU capability, or performance and power optimization for different
application scenarios.
Two firmwares are supported: 'WCN6855/hw2.0' and 'WCN6855/hw2.0/nfa765'.
The former is the default firmware, suitable for most WiFi 6 STA
functions. The latter adds support for commercial-quality SAP and
optimizes power consumption for IoT applications.
Signed-off-by: Miaoqing Pan <miaoqing.pan@oss.qualcomm.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/20250522013444.1301330-2-miaoqing.pan@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Since 2b0996c764 , all of this platform code became no-op with no OF
replacement. Not only that, there are no users of AHB here. Add an OF
match table that mostly mirrors the original platform device id table.
Use a qca prefix as is done for the only other property: qca,no-eeprom.
Also used qca prefix for ar9530 as the latter seems to be a mistake.
This will be used to add ath9k support for the various ath79 devices
here.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20250609030851.17739-5-rosenp@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
fbnic_fw_clear_cmpl() does the inverse of fbnic_mbx_set_cmpl().
It removes the completion from the mailbox table.
It also calls fbnic_mbx_set_cmpl_slot() internally.
It should have fbnic_mbx prefix, not fbnic_fw.
I'm not very clear on what the distinction is between the two
prefixes but the matching "set" and "clear" functions should
use the same prefix.
While at it move the "clear" function closer to the "set".
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250624142834.3275164-6-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Historically, the RGMII PHY modes specified in Device Trees have been
used inconsistently, often referring to the usage of delays on the PHY
side rather than describing the board; many drivers still implement this
incorrectly.
Require a comment in Devices Trees using these modes (usually mentioning
that the delay is realized on the PCB), so we can avoid adding more
incorrect uses (or will at least notice which drivers still need to be
fixed).
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/bc112b8aa510cf9df9ab33178d122f234d0aebf7.1750756583.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Pull bpf fixes from Alexei Starovoitov:
- Fix use-after-free in libbpf when map is resized (Adin Scannell)
- Fix verifier assumptions about 2nd argument of bpf_sysctl_get_name
(Jerome Marchand)
- Fix verifier assumption of nullness of d_inode in dentry (Song Liu)
- Fix global starvation of LRU map (Willem de Bruijn)
- Fix potential NULL dereference in btf_dump__free (Yuan Chen)
* tag 'bpf-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
selftests/bpf: adapt one more case in test_lru_map to the new target_free
libbpf: Fix possible use-after-free for externs
selftests/bpf: Convert test_sysctl to prog_tests
bpf: Specify access type of bpf_sysctl_get_name args
libbpf: Fix null pointer dereference in btf_dump__free on allocation failure
bpf: Adjust free target to avoid global starvation of LRU map
bpf: Mark dentry->d_inode as trusted_or_null
Pull mount fixes from Al Viro:
"Several mount-related fixes"
* tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
userns and mnt_idmap leak in open_tree_attr(2)
attach_recursive_mnt(): do not lock the covering tree when sliding something under it
replace collect_mounts()/drop_collected_mounts() with a safer variant
Jakub Kicinski says:
====================
netlink: specs: enforce strict naming of properties
I got annoyed once again by the name properties in the ethtool spec
which use underscore instead of dash. I previously assumed that there
is a lot of such properties in the specs so fixing them now would
be near impossible. On a closer look, however, I only found 22
(rough grep suggests we have ~4.8k names in the specs, so bad ones
are just 0.46%).
Add a regex to the JSON schema to enforce the naming, fix the few
bad names. I was hoping we could start enforcing this from newer
families, but there's no correlation between the protocol and the
number of errors. If anything classic netlink has more recently
added specs so it has fewer errors.
The regex is just for name properties which will end up visible
to the user (in Python or YNL CLI). I left the c-name properties
alone, those don't matter as much. C codegen rewrites them, anyway.
I'm not updating the spec for genetlink-c. Looks like it has no
users, new families use genetlink, all old ones need genetlink-legacy.
If these patches are merged I will remove genetlink-c completely
in net-next.
====================
Link: https://patch.msgid.link/20250624211002.3475021-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a regexp to make sure all names which may end up being visible
to the user consist of lower case characters, numbers and dashes.
Underscores keep sneaking into the specs, which is not visible
in the C code but makes the Python and alike inconsistent.
Note that starting with a number is okay, as in C the full
name will include the family name.
For legacy families we can't enforce the naming in the family
name or the multicast group names, as these are part of the
binary uAPI of the kernel.
For classic netlink we need to allow capital letters in names
of struct members. TC has some structs with capitalized members.
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Link: https://patch.msgid.link/20250624211002.3475021-11-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
