The RX/TX delays for the Ethernet PHY on the Linksprite pcDuino 3 Nano
are configured in hardware, using resistors that are populated to pull
the RTL8211E's RXDLY/TXDLY pins low or high as needed.
phy-mode should be set to rgmii-id to reflect this. Previously it was
set to rgmii, which used to work but now results in the delays being
disabled again as a result of the bugfix in commit bbc4d71d63 ("net:
phy: realtek: fix rtl8211e rx/tx delay config").
Tested on two pcDuino 3 Nano boards purchased in 2015. Without this fix,
Ethernet works unreliably on one board and doesn't work at all on the
other.
Fixes: 061035d456 ("ARM: dts: sun7i: Add dts file for pcDuino 3 Nano board")
Signed-off-by: Adam Sampson <ats@offog.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20201123174739.6809-1-ats@offog.org
DCDC1 regulator powers many different subsystems. While some of them can
work at 3.0 V, some of them can not. For example, VCC-HDMI can only work
between 3.24 V and 3.36 V. According to OS images provided by the board
manufacturer this regulator should be set to 3.3 V.
Set DCDC1 and DCDC1SW to 3.3 V in order to fix this.
Fixes: 23edc168bd ("ARM: dts: sun8i: Add board dts file for Banana Pi M2 Berry")
Fixes: 27e81e1970 ("ARM: dts: sun8i: v40: bananapi-m2-berry: Enable GMAC ethernet controller")
Signed-off-by: Pablo Greco <pgreco@centosproject.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/1604326755-39742-1-git-send-email-pgreco@centosproject.org
The Ethernet PHY on the Bananapi M1 has the RX and TX delays enabled on
the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 8a5b272fbf ("ARM: dts: sun7i: Add Banana Pi board")
Signed-off-by: Pablo Greco <pgreco@centosproject.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/1604326600-39544-1-git-send-email-pgreco@centosproject.org
The Ethernet PHY on the Bananapi M64 has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: e729549990 ("arm64: allwinner: bananapi-m64: Enable dwmac-sun8i")
Fixes: 94f4428867 ("arm64: dts: allwinner: A64: Restore EMAC changes")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-10-wens@kernel.org
The Ethernet PHY on the Libre Computer ALL-H5-CC has the RX and TX
delays enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 60d0426d76 ("arm64: dts: allwinner: h5: Add Libre Computer ALL-H5-CC H5 board")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-9-wens@kernel.org
The Ethernet PHY on the Bananapi M2+ has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 8c7ba536e7 ("ARM: sun8i: bananapi-m2-plus: Enable dwmac-sun8i")
Fixes: 4904337fe3 ("ARM: dts: sunxi: Restore EMAC changes (boards)")
Fixes: aa8fee415f ("ARM: dts: sun8i: h3: Split out non-SoC-specific parts of Bananapi M2 Plus")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-8-wens@kernel.org
The Ethernet PHY on the Cubieboard 4 and A80 Optimus have the RX
and TX delays enabled on the PHY, using pull-ups on the RXDLY and
TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 98048143b7 ("ARM: dts: sun9i: cubieboard4: Enable GMAC")
Fixes: bc9bd03a44 ("ARM: dts: sun9i: a80-optimus: Enable GMAC")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-7-wens@kernel.org
The Ethernet PHY on the Bananapi M3 and Cubietruck Plus have the RX
and TX delays enabled on the PHY, using pull-ups on the RXDLY and
TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 039359948a ("ARM: dts: sun8i: a83t: Enable Ethernet on two boards")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-6-wens@kernel.org
The Ethernet PHY on the Orange Pi Plus 2E has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 4904337fe3 ("ARM: dts: sunxi: Restore EMAC changes (boards)")
Fixes: 7a78ef92cd ("ARM: sun8i: h3: Enable EMAC with external PHY on Orange Pi Plus 2E")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-5-wens@kernel.org
The Ethernet PHY on the Bananapi M1+ has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 04c85ecad3 ("ARM: dts: sun7i: Add dts file for Bananapi M1 Plus board")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-4-wens@kernel.org
The Ethernet PHY on the Cubietruck has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 67073d9767 ("ARM: dts: sun7i: cubietruck: Enable the GMAC")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Emilio López <emilio@elopez.com.ar>
Reviewed-by: Emilio López <emilio@elopez.com.ar>
Link: https://lore.kernel.org/r/20201024162515.30032-3-wens@kernel.org
The Ethernet PHY on the A31 Hummingbird has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: c220aec2bb ("ARM: dts: sun6i: Add Merrii A31 Hummingbird support")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-2-wens@kernel.org
According to board schematic, PHY provides both, RX and TX delays.
However, according to "fix" Realtek provided for this board, only TX
delay should be provided by PHY.
Tests show that both variants work but TX only PHY delay works
slightly better.
Update ethernet node to reflect the fact that PHY provides TX delay.
Fixes: 94f4428867 ("arm64: dts: allwinner: A64: Restore EMAC changes")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201022211301.3548422-1-jernej.skrabec@siol.net
Before the commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e rx/tx
delay config"), the software overwrite for RX/TX delays of the RTL8211e
were not working properly and the Beelink GS1 had both RX/TX delay of RGMII
interface set using pull-up on the TXDLY and RXDLY pins.
Now that these delays are working properly they overwrite the HW
config and set this to 'rgmii' meaning no delay on both RX/TX.
This makes the ethernet of this board not working anymore.
Set the phy-mode to 'rgmii-id' meaning RGMII with RX/TX delays
in the device-tree to keep the correct configuration.
Fixes: 089bee8dd1 ("arm64: dts: allwinner: h6: Introduce Beelink GS1 board")
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20201018172409.1754775-1-peron.clem@gmail.com
tid_addr is not a "pointer to (pointer to int in userspace)"; it is in
fact a "pointer to (pointer to int in userspace) in userspace". So
sparse rightfully complains about passing a kernel pointer to
put_user().
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 453431a549 ("mm, treewide: rename kzfree() to
kfree_sensitive()") renamed kzfree() to kfree_sensitive(),
but it left a compatibility definition of kzfree() to avoid
being too disruptive.
Since then a few more instances of kzfree() have slipped in.
Just get rid of them and remove the compatibility definition
once and for all.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull timer fixes from Thomas Gleixner:
"A time namespace fix and a matching selftest. The futex absolute
timeouts which are based on CLOCK_MONOTONIC require time namespace
corrected. This was missed in the original time namesapce support"
* tag 'timers-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
selftests/timens: Add a test for futex()
futex: Adjust absolute futex timeouts with per time namespace offset
Pull scheduler fixes from Thomas Gleixner:
"Two scheduler fixes:
- A trivial build fix for sched_feat() to compile correctly with
CONFIG_JUMP_LABEL=n
- Replace a zero lenght array with a flexible array"
* tag 'sched-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/features: Fix !CONFIG_JUMP_LABEL case
sched: Replace zero-length array with flexible-array
Pull perf fix from Thomas Gleixner:
"A single fix to compute the field offset of the SNOOPX bit in the data
source bitmask of perf events correctly"
* tag 'perf-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: correct SNOOPX field offset
Pull locking fix from Thomas Gleixner:
"Just a trivial fix for kernel-doc warnings"
* tag 'locking-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/seqlocks: Fix kernel-doc warnings
Pull NTB fixes from Jon Mason.
* tag 'ntb-5.10' of git://github.com/jonmason/ntb:
NTB: Use struct_size() helper in devm_kzalloc()
ntb: intel: Fix memleak in intel_ntb_pci_probe
NTB: hw: amd: fix an issue about leak system resources
Pull i2c fix from Wolfram Sang:
"Regression fix for rc1 and stable kernels as well"
* 'i2c/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: core: Restore acpi_walk_dep_device_list() getting called after registering the ACPI i2c devs
Pull more cifs updates from Steve French:
"Add support for stat of various special file types (WSL reparse points
for char, block, fifo)"
* tag '5.10-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update internal module version number
smb3: add some missing definitions from MS-FSCC
smb3: remove two unused variables
smb3: add support for stat of WSL reparse points for special file types
Pull more parisc updates from Helge Deller:
- During this merge window O_NONBLOCK was changed to become 000200000,
but we missed that the syscalls timerfd_create(), signalfd4(),
eventfd2(), pipe2(), inotify_init1() and userfaultfd() do a strict
bit-wise check of the flags parameter.
To provide backward compatibility with existing userspace we
introduce parisc specific wrappers for those syscalls which filter
out the old O_NONBLOCK value and replaces it with the new one.
- Prevent HIL bus driver to get stuck when keyboard or mouse isn't
attached
- Improve error return codes when setting rtc time
- Minor documentation fix in pata_ns87415.c
* 'parisc-5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
ata: pata_ns87415.c: Document support on parisc with superio chip
parisc: Add wrapper syscalls to fix O_NONBLOCK flag usage
hil/parisc: Disable HIL driver when it gets stuck
parisc: Improve error return codes when setting rtc time
Pull more xen updates from Juergen Gross:
- a series for the Xen pv block drivers adding module parameters for
better control of resource usge
- a cleanup series for the Xen event driver
* tag 'for-linus-5.10b-rc1c-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
Documentation: add xen.fifo_events kernel parameter description
xen/events: unmask a fifo event channel only if it was masked
xen/events: only register debug interrupt for 2-level events
xen/events: make struct irq_info private to events_base.c
xen: remove no longer used functions
xen-blkfront: Apply changed parameter name to the document
xen-blkfront: add a parameter for disabling of persistent grants
xen-blkback: add a parameter for disabling of persistent grants
Pull SafeSetID updates from Micah Morton:
"The changes are mostly contained to within the SafeSetID LSM, with the
exception of a few 1-line changes to change some ns_capable() calls to
ns_capable_setid() -- causing a flag (CAP_OPT_INSETID) to be set that
is examined by SafeSetID code and nothing else in the kernel.
The changes to SafeSetID internally allow for setting up GID
transition security policies, as already existed for UIDs"
* tag 'safesetid-5.10' of git://github.com/micah-morton/linux:
LSM: SafeSetID: Fix warnings reported by test bot
LSM: SafeSetID: Add GID security policy handling
LSM: Signal to SafeSetID when setting group IDs
Pull random32 updates from Willy Tarreau:
"Make prandom_u32() less predictable.
This is the cleanup of the latest series of prandom_u32
experimentations consisting in using SipHash instead of Tausworthe to
produce the randoms used by the network stack.
The changes to the files were kept minimal, and the controversial
commit that used to take noise from the fast_pool (f227e3ec3b) was
reverted. Instead, a dedicated "net_rand_noise" per_cpu variable is
fed from various sources of activities (networking, scheduling) to
perturb the SipHash state using fast, non-trivially predictable data,
instead of keeping it fully deterministic. The goal is essentially to
make any occasional memory leakage or brute-force attempt useless.
The resulting code was verified to be very slightly faster on x86_64
than what is was with the controversial commit above, though this
remains barely above measurement noise. It was also tested on i386 and
arm, and build- tested only on arm64"
Link: https://lore.kernel.org/netdev/20200808152628.GA27941@SDF.ORG/
* tag '20201024-v4-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wtarreau/prandom:
random32: add a selftest for the prandom32 code
random32: add noise from network and scheduling activity
random32: make prandom_u32() output unpredictable
Commit 21653a4181 ("i2c: core: Call i2c_acpi_install_space_handler()
before i2c_acpi_register_devices()")'s intention was to only move the
acpi_install_address_space_handler() call to the point before where
the ACPI declared i2c-children of the adapter where instantiated by
i2c_acpi_register_devices().
But i2c_acpi_install_space_handler() had a call to
acpi_walk_dep_device_list() hidden (that is I missed it) at the end
of it, so as an unwanted side-effect now acpi_walk_dep_device_list()
was also being called before i2c_acpi_register_devices().
Move the acpi_walk_dep_device_list() call to the end of
i2c_acpi_register_devices(), so that it is once again called *after*
the i2c_client-s hanging of the adapter have been created.
This fixes the Microsoft Surface Go 2 hanging at boot.
Fixes: 21653a4181 ("i2c: core: Call i2c_acpi_install_space_handler() before i2c_acpi_register_devices()")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209627
Reported-by: Rainer Finke <rainer@finke.cc>
Reported-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Suggested-by: Maximilian Luz <luzmaximilian@gmail.com>
Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Pull block fixes from Jens Axboe:
- NVMe pull request from Christoph
- rdma error handling fixes (Chao Leng)
- fc error handling and reconnect fixes (James Smart)
- fix the qid displace when tracing ioctl command (Keith Busch)
- don't use BLK_MQ_REQ_NOWAIT for passthru (Chaitanya Kulkarni)
- fix MTDT for passthru (Logan Gunthorpe)
- blacklist Write Same on more devices (Kai-Heng Feng)
- fix an uninitialized work struct (zhenwei pi)"
- lightnvm out-of-bounds fix (Colin)
- SG allocation leak fix (Doug)
- rnbd fixes (Gioh, Guoqing, Jack)
- zone error translation fixes (Keith)
- kerneldoc markup fix (Mauro)
- zram lockdep fix (Peter)
- Kill unused io_context members (Yufen)
- NUMA memory allocation cleanup (Xianting)
- NBD config wakeup fix (Xiubo)
* tag 'block-5.10-2020-10-24' of git://git.kernel.dk/linux-block: (27 commits)
block: blk-mq: fix a kernel-doc markup
nvme-fc: shorten reconnect delay if possible for FC
nvme-fc: wait for queues to freeze before calling update_hr_hw_queues
nvme-fc: fix error loop in create_hw_io_queues
nvme-fc: fix io timeout to abort I/O
null_blk: use zone status for max active/open
nvmet: don't use BLK_MQ_REQ_NOWAIT for passthru
nvmet: cleanup nvmet_passthru_map_sg()
nvmet: limit passthru MTDS by BIO_MAX_PAGES
nvmet: fix uninitialized work for zero kato
nvme-pci: disable Write Zeroes on Sandisk Skyhawk
nvme: use queuedata for nvme_req_qid
nvme-rdma: fix crash due to incorrect cqe
nvme-rdma: fix crash when connect rejected
block: remove unused members for io_context
blk-mq: remove the calling of local_memory_node()
zram: Fix __zram_bvec_{read,write}() locking order
skd_main: remove unused including <linux/version.h>
sgl_alloc_order: fix memory leak
lightnvm: fix out-of-bounds write to array devices->info[]
...
Pull io_uring fixes from Jens Axboe:
- fsize was missed in previous unification of work flags
- Few fixes cleaning up the flags unification creds cases (Pavel)
- Fix NUMA affinities for completely unplugged/replugged node for io-wq
- Two fallout fixes from the set_fs changes. One local to io_uring, one
for the splice entry point that io_uring uses.
- Linked timeout fixes (Pavel)
- Removal of ->flush() ->files work-around that we don't need anymore
with referenced files (Pavel)
- Various cleanups (Pavel)
* tag 'io_uring-5.10-2020-10-24' of git://git.kernel.dk/linux-block:
splice: change exported internal do_splice() helper to take kernel offset
io_uring: make loop_rw_iter() use original user supplied pointers
io_uring: remove req cancel in ->flush()
io-wq: re-set NUMA node affinities if CPUs come online
io_uring: don't reuse linked_timeout
io_uring: unify fsize with def->work_flags
io_uring: fix racy REQ_F_LINK_TIMEOUT clearing
io_uring: do poll's hash_node init in common code
io_uring: inline io_poll_task_handler()
io_uring: remove extra ->file check in poll prep
io_uring: make cached_cq_overflow non atomic_t
io_uring: inline io_fail_links()
io_uring: kill ref get/drop in personality init
io_uring: flags-based creds init in queue
Pull misc vfs updates from Al Viro:
"Assorted stuff all over the place (the largest group here is
Christoph's stat cleanups)"
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: remove KSTAT_QUERY_FLAGS
fs: remove vfs_stat_set_lookup_flags
fs: move vfs_fstatat out of line
fs: implement vfs_stat and vfs_lstat in terms of vfs_fstatat
fs: remove vfs_statx_fd
fs: omfs: use kmemdup() rather than kmalloc+memcpy
[PATCH] reduce boilerplate in fsid handling
fs: Remove duplicated flag O_NDELAY occurring twice in VALID_OPEN_FLAGS
selftests: mount: add nosymfollow tests
Add a "nosymfollow" mount option.
Pull dma-mapping fixes from Christoph Hellwig:
- document the new dma_{alloc,free}_pages() API
- two fixups for the dma-mapping.h split
* tag 'dma-mapping-5.10-1' of git://git.infradead.org/users/hch/dma-mapping:
dma-mapping: document dma_{alloc,free}_pages
dma-mapping: move more functions to dma-map-ops.h
ARM/sa1111: add a missing include of dma-map-ops.h
Pull KVM fixes from Paolo Bonzini:
"Two fixes for this merge window, and an unrelated bugfix for a host
hang"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: ioapic: break infinite recursion on lazy EOI
KVM: vmx: rename pi_init to avoid conflict with paride
KVM: x86/mmu: Avoid modulo operator on 64-bit value to fix i386 build
