USBIP driver packs URB transfer flags in network packets that are
exchanged between Server (usbip_host) and Client (vhci_hcd).
URB_* flags are internal to kernel and could change. Where as USBIP
URB flags exchanged in network packets are USBIP user API must not
change.
Add USBIP_URB* flags to make this an explicit API and change the
client and server to map them. Details as follows:
Client tx path (USBIP_CMD_SUBMIT):
- Maps URB_* to USBIP_URB_* when it sends USBIP_CMD_SUBMIT packet.
Server rx path (USBIP_CMD_SUBMIT):
- Maps USBIP_URB_* to URB_* when it receives USBIP_CMD_SUBMIT packet.
Flags aren't included in USBIP_CMD_UNLINK and USBIP_RET_SUBMIT packets
and no special handling is needed for them in the following cases:
- Server rx path (USBIP_CMD_UNLINK)
- Client rx path & Server tx path (USBIP_RET_SUBMIT)
Update protocol documentation to reflect the change.
Suggested-by: Hongren Zenithal Zheng <i@zenithal.me>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20220824002456.94605-1-skhan@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During soft disconnect, EP0 events are expected to be handled in order to
allow the controller to successfully move into the halted state. Since
__dwc3_gadget_stop() is executed before polling, EP0 has been disabled, and
events are being blocked. Allow xfercomplete events to be handled, so that
cached SETUP packets can be read out from the internal controller memory.
Without doing so, it will lead to endxfer timeouts, which results to
controller halt failures.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220817182359.13550-5-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If any function drivers request for a delayed status phase, this leads to a
SETUP transfer timeout error, since the function may take longer to process
the DATA stage. This eventually results in end transfer timeouts, as there
is a pending SETUP transaction.
In addition, allow the DWC3_EP_DELAY_STOP to be set for if there is a
delayed status requested. Ocasionally, a host may abort the current SETUP
transaction, by issuing a subsequent SETUP token. In those situations, it
would result in an endxfer timeout as well.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220817182359.13550-3-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are some operations that need to be ignored if there is a soft
disconnect in progress. This is to avoid having a pending EP0 transfer in
progress while attempting to stop active transfers and halting the
controller.
There were several instances seen where a soft disconnect was able to occur
during early link negotiation, i.e. bus reset/conndone, which leads to the
conndone handler re-configuring EPs while attempting to halt the
controller, as DEP flags are cleared as part of the soft disconnect path.
ep0out: cmd 'Start New Configuration'
ep0out: cmd 'Set Endpoint Transfer Resource'
ep0in: cmd 'Set Endpoint Transfer Resource'
ep1out: cmd 'Set Endpoint Transfer Resource'
...
event (00030601): Suspend [U3]
event (00000101): Reset [U0]
ep0out: req ffffff87e5c9e100 length 0/0 zsI ==> 0
event (00000201): Connection Done [U0]
ep0out: cmd 'Start New Configuration'
ep0out: cmd 'Set Endpoint Transfer Resource'
In addition, if a soft disconnect occurs, EP0 events are still allowed to
process, however, it will stall/restart during the SETUP phase. The
host is still able to query for the DATA phase, leading to a
xfernotready(DATA) event. Since none of the SETUP transfer parameters are
populated, the xfernotready is treated as a "wrong direction" error,
leading to a duplicate stall/restart routine.
Add the proper softconnect/connected checks in sequences that are
potentially involved during soft disconnect processing.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220817182359.13550-2-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_maxpacket() looks up the endpoint number in the pipe which can fail
if the interface or configuration changes before the routine is called.
This is unexpected and may even cause a modulo by zero afterwards.
So use usb_endpoint_maxp() routine which uses the endpoint stored in URB
to get the maxpacket.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Khalid Masum <khalid.masum.92@gmail.com>
Addresses-Coverity: 744857 ("Division or modulo by zero")
Addresses-Coverity: 1487371 ("Division or modulo by zero")
Link: https://lore.kernel.org/r/20220824193813.13129-1-khalid.masum.92@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As follows from #define NAME_TEMPLATE, the procfs code in the RNDIS driver
expects the # of instances to be 3-digit decimal, while the driver calls
ida_simple_get() passing 0 as the 'end' argument which results in actual
max instance # of INT_MAX. Limit the maximum # of RNDIS instances to 1000
which is still a lot! :-)
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/a8180973-3ded-3644-585a-169589a37642@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RZ/V2M (r9a09g011) has a few differences:
- The USB3_DRD_CON register has moved, its called USB_PERI_DRD_CON in
the RZ/V2M hardware manual.
It has additional bits for host and peripheral reset that need to
cleared to use usb host and peripheral respectively.
- The USB3_OTG_STA, USB3_OTG_INT_STA and USB3_OTG_INT_ENA registers
have been moved and renamed to USB_PERI_DRD_STA, USB_PERI_DRD_INT_STA
and USB_PERI_DRD_INT_E.
- The IDMON bit used in the above regs for role detection have moved
from bit 4 to bit 0.
- RZ/V2M has an separate interrupt for DRD, i.e. for changes to IDMON.
- There are reset lines for DRD and USBP
- There is another clock, managed by runtime PM.
Whilst the hardware can support 16 pipes, it is artifically limited
based on the ram per pipe calculation. With the 4KB ram per pipe, we
can support 9 pipes consisting of 4xIN pipes, 4xOUT pipes and PIPE0.
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Link: https://lore.kernel.org/r/20220804192220.128601-3-phil.edworthy@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The functions stop_active_transfers and ep_disable are both calling
remove_requests. This functions in both cases will giveback the requests
with status ESHUTDOWN, which also represents an physical disconnection.
For ep_disable this is not true. This patch adds the status parameter to
remove_requests and sets the status to ECONNRESET on ep_disable.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220720213523.1055897-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Radix tree header includes gfp.h for __GFP_BITS_SHIFT only. Now we
have gfp_types.h for this.
Fixes powerpc allmodconfig build:
In file included from include/linux/nodemask.h:97,
from include/linux/mmzone.h:17,
from include/linux/gfp.h:7,
from include/linux/radix-tree.h:12,
from include/linux/idr.h:15,
from include/linux/kernfs.h:12,
from include/linux/sysfs.h:16,
from include/linux/kobject.h:20,
from include/linux/pci.h:35,
from arch/powerpc/kernel/prom_init.c:24:
include/linux/random.h: In function 'add_latent_entropy':
>> include/linux/random.h:25:46: error: 'latent_entropy' undeclared (first use in this function); did you mean 'add_latent_entropy'?
25 | add_device_randomness((const void *)&latent_entropy, sizeof(latent_entropy));
| ^~~~~~~~~~~~~~
| add_latent_entropy
include/linux/random.h:25:46: note: each undeclared identifier is reported only once for each function it appears in
Reported-by: kernel test robot <lkp@intel.com>
CC: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
