This make use of the CS35L41 HDA Property framework, which supports
laptops which do not have the _DSD properties in their ACPI.
Add configuration table to be able to use a generic function which allows
laptops to be supported just by adding an entry into the table.
Use configuration table function for existing system 103C89C6.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231218151221.388745-2-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, cur_prog/cur_conf remains at the default value (-1), while
program 0 has been loaded into the amplifiers.
In the playback hook, tasdevice_tuning_switch tries to restore the
cur_prog/cur_conf. In the runtime_resume/system_resume,
tasdevice_prmg_load tries to load the cur_prog as well.
Set cur_prog and cur_conf to 0 if available in the firmware.
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
CC: stable@vger.kernel.org
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Link: https://lore.kernel.org/r/038add0bdca1f979cc7abcce8f24cbcd3544084b.1702596646.git.soyer@irl.hu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Calling component_add starts loading the firmware, the callback function
writes the program to the amplifiers. If the module resets the
amplifiers after component_add, it happens that one of the amplifiers
does not work because the reset and program writing are interleaving.
Call tas2781_reset before component_add to ensure reliable
initialization.
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
CC: stable@vger.kernel.org
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Link: https://lore.kernel.org/r/4d23bf58558e23ee8097de01f70f1eb8d9de2d15.1702511246.git.soyer@irl.hu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the module can load the RCA but not the firmware binary, it will call
the cleanup functions. Then unloading the module causes general
protection fault due to double free.
Do not call the cleanup functions in tasdev_fw_ready.
general protection fault, probably for non-canonical address
0x6f2b8a2bff4c8fec: 0000 [#1] PREEMPT SMP NOPTI
Call Trace:
<TASK>
? die_addr+0x36/0x90
? exc_general_protection+0x1c5/0x430
? asm_exc_general_protection+0x26/0x30
? tasdevice_config_info_remove+0x6d/0xd0 [snd_soc_tas2781_fmwlib]
tas2781_hda_unbind+0xaa/0x100 [snd_hda_scodec_tas2781_i2c]
component_unbind+0x2e/0x50
component_unbind_all+0x92/0xa0
component_del+0xa8/0x140
tas2781_hda_remove.isra.0+0x32/0x60 [snd_hda_scodec_tas2781_i2c]
i2c_device_remove+0x26/0xb0
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
CC: stable@vger.kernel.org
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Link: https://lore.kernel.org/r/1a0885c424bb21172702d254655882b59ef6477a.1702510018.git.soyer@irl.hu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The code does not properly check whether the calibration variable is
available in the EFI. If it is not available, it causes a NULL pointer
dereference.
Check the return value of the first get_variable call also.
BUG: kernel NULL pointer dereference, address: 0000000000000000
Call Trace:
<TASK>
? __die+0x23/0x70
? page_fault_oops+0x171/0x4e0
? srso_alias_return_thunk+0x5/0x7f
? schedule+0x5e/0xd0
? exc_page_fault+0x7f/0x180
? asm_exc_page_fault+0x26/0x30
? crc32_body+0x2c/0x120
? tas2781_save_calibration+0xe4/0x220 [snd_hda_scodec_tas2781_i2c]
tasdev_fw_ready+0x1af/0x280 [snd_hda_scodec_tas2781_i2c]
request_firmware_work_func+0x59/0xa0
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
CC: stable@vger.kernel.org
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Link: https://lore.kernel.org/r/f1f6583bda918f78556f67d522ca7b3b91cebbd5.1702251102.git.soyer@irl.hu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Stop timer in the 'trigger' and 'sync_stop' callbacks since we want
the timer to be stopped before the DMA buffer is released. Otherwise,
it could trigger a kernel panic in some circumstances, for instance
when the DMA buffer is already released but the timer callback is
still running.
Signed-off-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Link: https://lore.kernel.org/r/20231206223211.12761-1-ivan.orlov0322@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASoC: Fixes for v6.7
A crop of fixes for v6.7, one core fix for a merge issue and a bunch of
driver specific fixes and new IDs, mostly for x86 platforms.
Merge series from srinivas.kandagatla@linaro.org:
Limit the speaker digital gains to 0dB so that the users will not damage them.
Currently there is a limit in UCM, but this does not stop the user form
changing the digital gains from command line. So limit this in driver
which makes the speakers more safer without active speaker protection in
place.
Apart from this there is also a range check fix in snd_soc_limit_volume
to allow setting this limit correctly.
Tested on Lenovo X13s.
The current driver is registering the same dais for each hdev found in the
system which results duplicated widgets to be registered and the kernel
log contains similar prints:
snd_hda_codec_realtek ehdaudio0D0: ASoC: sink widget AIF1TX overwritten
snd_hda_codec_realtek ehdaudio0D0: ASoC: source widget AIF1RX overwritten
skl_hda_dsp_generic skl_hda_dsp_generic: ASoC: sink widget hifi3 overwritten
skl_hda_dsp_generic skl_hda_dsp_generic: ASoC: sink widget hifi2 overwritten
skl_hda_dsp_generic skl_hda_dsp_generic: ASoC: sink widget hifi1 overwritten
skl_hda_dsp_generic skl_hda_dsp_generic: ASoC: source widget Codec Output Pin1 overwritten
skl_hda_dsp_generic skl_hda_dsp_generic: ASoC: sink widget Codec Input Pin1 overwritten
skl_hda_dsp_generic skl_hda_dsp_generic: ASoC: sink widget Analog Codec Playback overwritten
skl_hda_dsp_generic skl_hda_dsp_generic: ASoC: sink widget Digital Codec Playback overwritten
skl_hda_dsp_generic skl_hda_dsp_generic: ASoC: sink widget Alt Analog Codec Playback overwritten
skl_hda_dsp_generic skl_hda_dsp_generic: ASoC: source widget Analog Codec Capture overwritten
skl_hda_dsp_generic skl_hda_dsp_generic: ASoC: source widget Digital Codec Capture overwritten
skl_hda_dsp_generic skl_hda_dsp_generic: ASoC: source widget Alt Analog Codec Capture overwritten
To avoid such issue, split the dai array into HDMI and non HDMI array and
register them conditionally:
for HDMI hdev only register the dais needed for HDMI
for non HDMI hdev do not register the HDMI dais.
Depends-on: 3d1dc8b103 ("ASoC: Intel: skl_hda_dsp_generic: Drop HDMI routes when HDMI is not available")
Link: https://github.com/thesofproject/linux/issues/4509
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20231128123914.3986-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It's been reported that the runtime PM on KONTRON SinglePC (PCI SSID
1734:1232) caused a stall of playback after a bunch of invocations.
(FWIW, this looks like an timing issue, and the stall happens rather
on the controller side.)
As a workaround, disable the default power-save on this platform.
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231130151321.9813-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge series from Peter Ujfalusi <peter.ujfalusi@linux.intel.com>:
In the current code, we enable a widget core when it is set up and
disable it when it is freed. This is problematic with IPC4 because
widget free is essentially a NOP and all widgets are freed in the
firmware when the pipeline is deleted. This results in a crash during
pipeline deletion when one of it's widgets is scheduled to run on a
secondary core and is powered off when widget is freed. So, change the
logic to enable all cores needed by all the modules in a pipeline when
the pipeline widget is set up and disable them after the pipeline
widget is freed.
In the current code, we enable a widget core when it is set up and
disable it when it is freed. This is problematic with IPC4 because
widget free is essentially a NOP and all widgets are freed in the
firmware when the pipeline is deleted. This results in a crash during
pipeline deletion when one of it's widgets is scheduled to run on a
secondary core and is powered off when widget is freed. So, change the
logic to enable all cores needed by all the modules in a pipeline when
the pipeline widget is set up and disable them after the pipeline
widget is freed.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20231124135743.24674-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A recent change to address pops and clicks with codecs like WSA883X
touched the same code paths as a fix for clearing DAI parameters and
resulted in a bad merge.
Specifically, commit f0220575e6 ("ASoC: soc-dai: add flag to mute and
unmute stream during trigger") made mute at stream close conditional,
while commit 3efcb471f8 ("ASoC: soc-pcm.c: Make sure DAI parameters
cleared if the DAI becomes inactive") moved that same mute call back to
soc_pcm_hw_clean().
Fix up the bad merge by dropping the second mute call from
soc_pcm_clean() and making sure that the call in soc_pcm_hw_clean() is
conditional as intended.
Fixes: bdb7e19220 ("ASoC: Merge up workaround for CODECs that play noise on stopped stream")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20231123091815.21933-1-johan+linaro@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
