At the default TX trigger level of 2 in non-DMA mode (meaning that an
interrupt is generated when less than 2 characters are left in the
FIFO), we have observed frequent buffer underruns at 115200 Baud on an
i.MX8M Nano. This can cause communication issues if the receiving side
expects a continuous transfer.
Increasing the level to 8 makes the UART trigger an interrupt earlier,
giving the kernel enough time to refill the FIFO, at the cost of
triggering one interrupt per ~24 instead of ~30 bytes of transmitted
data (as the i.MX UART has a 32 byte FIFO).
Signed-off-by: Michael Krummsdorf <michael.krummsdorf@tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20240508133744.35858-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250_pnp sets drvdata to line + 1 if the probe is successful. The users
of drvdata are in remove, suspend and resume callbacks, none of which
will be called if probe failed. The line acquired from drvdata can
never be zero in those functions and the checks for that can be
removed.
Eliminate also +/-1 step because all users of line subtract 1 from the
value.
These might have been leftover from legacy PM callbacks that could
be called without probe being successful.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240506121202.11253-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hrtimer for RXDMA timeout was unconditionally restarted in the RXDMA
complete handler ignoring the fact that setting up DMA may fail and PIO
is used instead. Explicitly stop the timer when DMA is completed and
only restart it when setting up DMA was successful. This makes the
intention of the timer much clearer, the driver easier to understand and
simplifies assumptions about the timer. The latter avoids race
conditions if these assumptions were not met or confused.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20240506114016.30498-9-wsa+renesas@sang-engineering.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case the UART port is used as a console, no_console_suspend is
available in bootargs and UART port is part of a software-controlled power
domain we need to call device_set_awake_path(). This lets the power
domain core code know that this domain should not be powered off
during system suspend. Otherwise, the UART port power domain is turned off,
nothing is printed while suspending and the suspend/resume process is
blocked. This was detected on the Renesas RZ/G3S SoC while adding support
for power domains.
Based on code investigation (on v6.9-rc5), this issue is present on other
SoCs (e.g., Renesas R-Mobile A1 [1], IMX8QXP [2]) and different SoCs have
particular implementation to handle it. Due to this the patch added the
call of device_set_awake_path() in uart_suspend_port() instead of having
it in the platform specific UART driver.
[1] drivers/pmdomain/renesas/rmobile-sysc.c:116
[2] drivers/pmdomain/imx/scu-pd.c:357
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Tony Lindgren <tony.lindgren@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20240430095930.2806067-1-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want the tty fixes in here as well, and it resolves a merge conflict
in:
drivers/tty/serial/serial_core.c
as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull char / misc driver fixes from Greg KH:
"Here are some small char/misc and other driver fixes for 6.9-rc5.
Included in here are the following:
- binder driver fix for reported problem
- speakup crash fix
- mei driver fixes for reported problems
- comdei driver fix
- interconnect driver fixes
- rtsx driver fix
- peci.h kernel doc fix
All of these have been in linux-next for over a week with no reported
problems"
* tag 'char-misc-6.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
peci: linux/peci.h: fix Excess kernel-doc description warning
binder: check offset alignment in binder_get_object()
comedi: vmk80xx: fix incomplete endpoint checking
mei: vsc: Unregister interrupt handler for system suspend
Revert "mei: vsc: Call wake_up() in the threaded IRQ handler"
misc: rtsx: Fix rts5264 driver status incorrect when card removed
mei: me: disable RPL-S on SPS and IGN firmwares
speakup: Avoid crash on very long word
interconnect: Don't access req_list while it's being manipulated
interconnect: qcom: x1e80100: Remove inexistent ACV_PERF BCM
Pull kernfs bugfix and documentation update from Greg KH:
"Here are two changes for 6.9-rc5 that deal with "driver core" stuff,
that do the following:
- sysfs reference leak fix
- embargoed-hardware-issues.rst update for Power
Both of these have been in linux-next for over a week with no reported
issues"
* tag 'driver-core-6.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
Documentation: embargoed-hardware-issues.rst: Add myself for Power
fs: sysfs: Fix reference leak in sysfs_break_active_protection()
Pull tty/serial driver fixes from Greg KH:
"Here are some small tty and serial driver fixes for 6.9-rc5 that
resolve a bunch of reported problems. Included in here are:
- MAINTAINERS and .mailmap update for Richard Genoud
- serial core regression fixes from 6.9-rc1 changes
- pci id cleanups
- serial core crash fix
- stm32 driver fixes
- 8250 driver fixes
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: stm32: Reset .throttled state in .startup()
serial: stm32: Return IRQ_NONE in the ISR if no handling happend
serial: core: Fix missing shutdown and startup for serial base port
serial: core: Clearing the circular buffer before NULLifying it
MAINTAINERS: mailmap: update Richard Genoud's email address
serial/pmac_zilog: Remove flawed mitigation for rx irq flood
serial: 8250_pci: Remove redundant PCI IDs
serial: core: Fix regression when runtime PM is not enabled
serial: mxs-auart: add spinlock around changing cts state
serial: 8250_dw: Revert: Do not reclock if already at correct rate
serial: 8250_lpc18xx: disable clks on error in probe()
Pull USB / Thunderbolt driver fixes from Greg KH:
"Here are some small USB and Thunderbolt driver fixes for 6.9-rc5.
Included in here are:
- MAINTAINER file update for invalid email address
- usb-serial device id updates
- typec driver fixes
- thunderbolt / usb4 driver fixes
- usb core shutdown fixes
- cdc-wdm driver revert for reported problem in -rc1
- usb gadget driver fixes
- xhci driver fixes
All of these have been in linux-next for a while with no reported
problems"
* tag 'usb-6.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (25 commits)
USB: serial: option: add Telit FN920C04 rmnet compositions
usb: dwc3: ep0: Don't reset resource alloc flag
Revert "usb: cdc-wdm: close race between read and workqueue"
USB: serial: option: add Rolling RW101-GL and RW135-GL support
USB: serial: option: add Lonsung U8300/U9300 product
USB: serial: option: add support for Fibocom FM650/FG650
USB: serial: option: support Quectel EM060K sub-models
USB: serial: option: add Fibocom FM135-GL variants
usb: misc: onboard_usb_hub: Disable the USB hub clock on failure
thunderbolt: Avoid notify PM core about runtime PM resume
thunderbolt: Fix wake configurations after device unplug
usb: dwc2: host: Fix dereference issue in DDMA completion flow.
usb: typec: mux: it5205: Fix ChipID value typo
MAINTAINERS: Drop Li Yang as their email address stopped working
usb: gadget: fsl: Initialize udc before using it
usb: Disable USB3 LPM at shutdown
usb: gadget: f_ncm: Fix UAF ncm object at re-bind after usb ep transport error
usb: typec: tcpm: Correct the PDO counting in pd_set
usb: gadget: functionfs: Wait for fences before enqueueing DMABUF
usb: gadget: functionfs: Fix inverted DMA fence direction
...
Pull scheduler fix from Borislav Petkov:
- Add a missing memory barrier in the concurrency ID mm switching
* tag 'sched_urgent_for_v6.9_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Add missing memory barrier in switch_mm_cid
Pull x86 fixes from Borislav Petkov:
- Fix CPU feature dependencies of GFNI, VAES, and VPCLMULQDQ
- Print the correct error code when FRED reports a bad event type
- Add a FRED-specific INT80 handler without the special dances that
need to happen in the current one
- Enable the using-the-default-return-thunk-but-you-should-not warning
only on configs which actually enable those special return thunks
- Check the proper feature flags when selecting BHI retpoline
mitigation
* tag 'x86_urgent_for_v6.9_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpufeatures: Fix dependencies for GFNI, VAES, and VPCLMULQDQ
x86/fred: Fix incorrect error code printout in fred_bad_type()
x86/fred: Fix INT80 emulation for FRED
x86/retpolines: Enable the default thunk warning only on relevant configs
x86/bugs: Fix BHI retpoline check
Pull block fixes from Jens Axboe:
"Just two minor fixes that should go into the 6.9 kernel release, one
fixing a regression with partition scanning errors, and one fixing a
WARN_ON() that can get triggered if we race with a timer"
* tag 'block-6.9-20240420' of git://git.kernel.dk/linux:
blk-iocost: do not WARN if iocg was already offlined
block: propagate partition scanning errors to the BLKRRPART ioctl
Pull email address update from James Bottomley:
"My IBM email has stopped working, so update to a working email
address"
* tag 'email' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
MAINTAINERS: update to working email address
Pull kvm fixes from Paolo Bonzini:
"This is a bit on the large side, mostly due to two changes:
- Changes to disable some broken PMU virtualization (see below for
details under "x86 PMU")
- Clean up SVM's enter/exit assembly code so that it can be compiled
without OBJECT_FILES_NON_STANDARD. This fixes a warning "Unpatched
return thunk in use. This should not happen!" when running KVM
selftests.
Everything else is small bugfixes and selftest changes:
- Fix a mostly benign bug in the gfn_to_pfn_cache infrastructure
where KVM would allow userspace to refresh the cache with a bogus
GPA. The bug has existed for quite some time, but was exposed by a
new sanity check added in 6.9 (to ensure a cache is either
GPA-based or HVA-based).
- Drop an unused param from gfn_to_pfn_cache_invalidate_start() that
got left behind during a 6.9 cleanup.
- Fix a math goof in x86's hugepage logic for
KVM_SET_MEMORY_ATTRIBUTES that results in an array overflow
(detected by KASAN).
- Fix a bug where KVM incorrectly clears root_role.direct when
userspace sets guest CPUID.
- Fix a dirty logging bug in the where KVM fails to write-protect
SPTEs used by a nested guest, if KVM is using Page-Modification
Logging and the nested hypervisor is NOT using EPT.
x86 PMU:
- Drop support for virtualizing adaptive PEBS, as KVM's
implementation is architecturally broken without an obvious/easy
path forward, and because exposing adaptive PEBS can leak host LBRs
to the guest, i.e. can leak host kernel addresses to the guest.
- Set the enable bits for general purpose counters in
PERF_GLOBAL_CTRL at RESET time, as done by both Intel and AMD
processors.
- Disable LBR virtualization on CPUs that don't support LBR
callstacks, as KVM unconditionally uses
PERF_SAMPLE_BRANCH_CALL_STACK when creating the perf event, and
would fail on such CPUs.
Tests:
- Fix a flaw in the max_guest_memory selftest that results in it
exhausting the supply of ucall structures when run with more than
256 vCPUs.
- Mark KVM_MEM_READONLY as supported for RISC-V in
set_memory_region_test"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (30 commits)
KVM: Drop unused @may_block param from gfn_to_pfn_cache_invalidate_start()
KVM: selftests: Add coverage of EPT-disabled to vmx_dirty_log_test
KVM: x86/mmu: Fix and clarify comments about clearing D-bit vs. write-protecting
KVM: x86/mmu: Remove function comments above clear_dirty_{gfn_range,pt_masked}()
KVM: x86/mmu: Write-protect L2 SPTEs in TDP MMU when clearing dirty status
KVM: x86/mmu: Precisely invalidate MMU root_role during CPUID update
KVM: VMX: Disable LBR virtualization if the CPU doesn't support LBR callstacks
perf/x86/intel: Expose existence of callback support to KVM
KVM: VMX: Snapshot LBR capabilities during module initialization
KVM: x86/pmu: Do not mask LVTPC when handling a PMI on AMD platforms
KVM: x86: Snapshot if a vCPU's vendor model is AMD vs. Intel compatible
KVM: x86: Stop compiling vmenter.S with OBJECT_FILES_NON_STANDARD
KVM: SVM: Create a stack frame in __svm_sev_es_vcpu_run()
KVM: SVM: Save/restore args across SEV-ES VMRUN via host save area
KVM: SVM: Save/restore non-volatile GPRs in SEV-ES VMRUN via host save area
KVM: SVM: Clobber RAX instead of RBX when discarding spec_ctrl_intercepted
KVM: SVM: Drop 32-bit "support" from __svm_sev_es_vcpu_run()
KVM: SVM: Wrap __svm_sev_es_vcpu_run() with #ifdef CONFIG_KVM_AMD_SEV
KVM: SVM: Create a stack frame in __svm_vcpu_run() for unwinding
KVM: SVM: Remove a useless zeroing of allocated memory
...
Pull powerpc fixes from Michael Ellerman:
- Fix wireguard loading failure on pre-Power10 due to Power10 crypto
routines
- Fix papr-vpd selftest failure due to missing variable initialization
- Avoid unnecessary get/put in spapr_tce_platform_iommu_attach_dev()
Thanks to Geetika Moolchandani, Jason Gunthorpe, Michal Suchánek, Nathan
Lynch, and Shivaprasad G Bhat.
* tag 'powerpc-6.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
selftests/powerpc/papr-vpd: Fix missing variable initialization
powerpc/crypto/chacha-p10: Fix failure on non Power10
powerpc/iommu: Refactor spapr_tce_platform_iommu_attach_dev()
Pull clk fixes from Stephen Boyd:
"A couple clk driver fixes, a build fix, and a deadlock fix:
- Mediatek mt7988 has broken PCIe because the wrong parent is used
- Mediatek clk drivers may deadlock when registering their clks
because the clk provider device is repeatedly runtime PM resumed
and suspended during probe and clk registration.
Resuming the clk provider device deadlocks with an ABBA deadlock
due to genpd_lock and the clk prepare_lock. The fix is to keep the
device runtime resumed while registering clks.
- Another runtime PM related deadlock, this time with disabling
unused clks during late init.
We get an ABBA deadlock where a device is runtime PM resuming (or
suspending) while the disabling of unused clks is happening in
parallel. That runtime PM action calls into the clk framework and
tries to grab the clk prepare_lock while the disabling of unused
clks holds the prepare_lock and is waiting for that runtime PM
action to complete.
The fix is to runtime resume all the clk provider devices before
grabbing the clk prepare_lock during disable unused.
- A build fix to provide an empty devm_clk_rate_exclusive_get()
function when CONFIG_COMMON_CLK=n"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: mediatek: mt7988-infracfg: fix clocks for 2nd PCIe port
clk: mediatek: Do a runtime PM get on controllers during probe
clk: Get runtime PM before walking tree for clk_summary
clk: Get runtime PM before walking tree during disable_unused
clk: Initialize struct clk_core kref earlier
clk: Don't hold prepare_lock when calling kref_put()
clk: Remove prepare_lock hold assertion in __clk_release()
clk: Provide !COMMON_CLK dummy for devm_clk_rate_exclusive_get()
Pull perf tools fixes from Namhyung Kim:
"A random set of small bug fixes:
- Fix perf annotate TUI when used with data type profiling
- Work around BPF verifier about sighand lock checking
And a set of kernel header synchronization"
* tag 'perf-tools-fixes-for-v6.9-2024-04-19' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools:
tools/include: Sync arm64 asm/cputype.h with the kernel sources
tools/include: Sync asm-generic/bitops/fls.h with the kernel sources
tools/include: Sync x86 asm/msr-index.h with the kernel sources
tools/include: Sync x86 asm/irq_vectors.h with the kernel sources
tools/include: Sync x86 CPU feature headers with the kernel sources
tools/include: Sync uapi/sound/asound.h with the kernel sources
tools/include: Sync uapi/linux/kvm.h and asm/kvm.h with the kernel sources
tools/include: Sync uapi/linux/fs.h with the kernel sources
tools/include: Sync uapi/drm/i915_drm.h with the kernel sources
perf lock contention: Add a missing NULL check
perf annotate: Make sure to call symbol__annotate2() in TUI
Pull iommufd fixes from Jason Gunthorpe:
"Two fixes for the selftests:
- CONFIG_IOMMUFD_TEST needs CONFIG_IOMMUFD_DRIVER to work
- The kconfig fragment sshould include fault injection so the fault
injection test can work"
* tag 'for-linus-iommufd' of git://git.kernel.org/pub/scm/linux/kernel/git/jgg/iommufd:
iommufd: Add config needed for iommufd_fail_nth
iommufd: Add missing IOMMUFD_DRIVER kconfig for the selftest
Pull rdma fixes from Jason Gunthorpe:
- Add a missing mutex_destroy() in rxe
- Enhance the debugging print for cm_destroy failures to help debug
these
- Fix mlx5 MAD processing in cases where multiport devices are running
in switchedev mode
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/mlx5: Fix port number for counter query in multi-port configuration
RDMA/cm: Print the old state when cm_destroy_id gets timeout
RDMA/rxe: Fix the problem "mutex_destroy missing"
Pull fs/9p fixes from Eric Van Hensbergen:
"This contains a reversion of one of the original 6.9 patches which
seems to have been the cause of most of the instability. It also
incorporates several fixes to legacy support and cache fixes.
There are few additional changes to improve stability, but I want
another week of testing before sending them upstream"
* tag '9p-fixes-for-6.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
fs/9p: drop inodes immediately on non-.L too
fs/9p: Revert "fs/9p: fix dups even in uncached mode"
fs/9p: remove erroneous nlink init from legacy stat2inode
9p: explicitly deny setlease attempts
fs/9p: fix the cache always being enabled on files with qid flags
fs/9p: translate O_TRUNC into OTRUNC
fs/9p: only translate RWX permissions for plain 9P2000
Pull fuse fixes from Miklos Szeredi:
- Fix two bugs in the new passthrough mode
- Fix a statx bug introduced in v6.6
- Fix code documentation
* tag 'fuse-fixes-6.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
cuse: add kernel-doc comments to cuse_process_init_reply()
fuse: fix leaked ENOSYS error on first statx call
fuse: fix parallel dio write on file open in passthrough mode
fuse: fix wrong ff->iomode state changes from parallel dio write
Pull arm64 fixes from Catalin Marinas:
- Fix a kernel fault during page table walking in huge_pte_alloc() with
PTABLE_LEVELS=5 due to using p4d_offset() instead of p4d_alloc()
- head.S fix and cleanup to disable the MMU before toggling the
HCR_EL2.E2H bit when entering the kernel with the MMU on from the EFI
stub. Changing this bit (currently from VHE to nVHE) causes some
system registers as well as page table descriptors to be interpreted
differently, potentially resulting in spurious MMU faults
- Fix translation fault in swsusp_save() accessing MEMBLOCK_NOMAP
memory ranges due to kernel_page_present() returning true in most
configurations other than rodata_full == true,
CONFIG_DEBUG_PAGEALLOC=y or CONFIG_KFENCE=y
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: hibernate: Fix level3 translation fault in swsusp_save()
arm64/head: Disable MMU at EL2 before clearing HCR_EL2.E2H
arm64/head: Drop unnecessary pre-disable-MMU workaround
arm64/hugetlb: Fix page table walk in huge_pte_alloc()
Pull s390 updates from Alexander Gordeev:
- Fix NULL pointer dereference in program check handler
- Fake IRBs are important events relevant for problem analysis. Add
traces when queueing and delivering
- Fix a race condition in ccw_device_set_online() that can cause the
online process to fail
- Deferred condition code 1 response indicates that I/O was not started
and should be retried. The current QDIO implementation handles a cc1
response as an error, resulting in a failed QDIO setup. Fix that by
retrying the setup when a cc1 response is received
* tag 's390-6.9-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/mm: Fix NULL pointer dereference
s390/cio: log fake IRB events
s390/cio: fix race condition during online processing
s390/qdio: handle deferred cc1
Pull bootconfig fixes from Masami Hiramatsu:
- Fix potential static_command_line buffer overrun.
Currently we allocate the memory for static_command_line based on
"boot_command_line", but it will copy "command_line" into it. So we
use the length of "command_line" instead of "boot_command_line" (as
we previously did)
- Use memblock_free_late() in xbc_exit() instead of memblock_free()
after the buddy system is initialized
- Fix a kerneldoc warning
* tag 'bootconfig-fixes-v6.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
bootconfig: Fix the kerneldoc of _xbc_exit()
bootconfig: use memblock_free_late to free xbc memory to buddy
init/main.c: Fix potential static_command_line memory overflow
