Add an API to associate a PGT entry with SMPE index and add or remove a
port. This API will be used by FID code and MDB code, to add/remove port
from specific PGT entry.
When the first port is added to PGT entry, allocate the entry in the given
MID index, when the last port is removed from PGT entry, free it.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently when bitmap of ports is needed, 'unsigned long *' type is
used. The functions which use the bitmap assume its length according to
its name, i.e., each function which gets a bitmap of ports queries the
maximum number of ports and uses it as the size.
As preparation for the next patch which will use bitmap of ports, add a
dedicated structure for it. Refactor the existing code to use the new
structure.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In Spectrum-1, the index into the MPE table - called switch multicast to
port egress VID (SMPE) - is derived from the PGT entry, whereas in
Spectrum-2 and later ASICs it is derived from the FID.
Therefore, in Spectrum-1, the SMPE index needs to be programmed as part of
the PGT entry via SMID register, while it is reserved for Spectrum-2 and
later ASICs.
Add 'pgt_smpe_index_valid' boolean as part of 'struct mlxsw_sp' and set
it to true for Spectrum-1 and to false for the later ASICs. Add
'smpe_index_valid' as part of 'struct mlxsw_sp_pgt' and set it according
to the value in 'struct mlxsw_sp' as part of PGT initialization.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The PGT (Port Group Table) table maps an index to a bitmap of local ports
to which a packet needs to be replicated. This table is used for layer 2
multicast and flooding.
In the legacy model, software did not interact with this table directly.
Instead, it was accessed by firmware in response to registers such as
SFTR and SMID. In the new model, the SFTR register is deprecated and
software has full control over the PGT table using the SMID register.
The entire state of the PGT table needs to be maintained in software
because member ports in a PGT entry needs to be reference counted to avoid
releasing entries which are still in use.
Add the following APIs:
1. mlxsw_sp_pgt_{init, fini}() - allocate/free the PGT table.
2. mlxsw_sp_pgt_mid_alloc_range() - allocate a range of MID indexes in PGT.
To be used by FID code during initialization to reserve specific PGT
indexes for flooding entries.
3. mlxsw_sp_pgt_mid_free_range() - free indexes in a given range.
4. mlxsw_sp_pgt_mid_alloc() - allocate one MID index in the PGT at a
non-specific range, just search for free index. To be used by MDB code.
5. mlxsw_sp_pgt_mid_free() - free the given index.
Note that alloc() functions do not allocate the entries in software, just
allocate IDs using 'idr'.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The device includes two main tables to support layer 2 multicast (i.e.,
MDB and flooding). These are the PGT (Port Group Table) table and the MPE
(Multicast Port Egress) table.
- PGT is {MID -> (bitmap of local_port, SPME index)}
- MPE is {(Local port, SMPE index) -> eVID}
In the legacy model, software did not interact with MPE table as it was
completely hidden in firmware. In the new model, software needs to
populate the table itself in order to map from {Local port, SMPE} to an
egress VID. This is done using the SMPE register.
Configure SMPE register when a {Local port, VID} are mapped/unmapped to a
802.1d and 802.1q emulated FIDs. The MPE table is not relevant for rFIDs as
firmware handles their flooding.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In the unified bridge model, the bridge type FID attribute is no longer
configured by the firmware, but instead by software when creating and
editing a FID via SFMR register.
Set this field as part of FID creation and edition flow. Default to 0
(reserved) as long as the driver operates in the legacy bridge model.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently, 'bridge_type' is an attribute of 'struct mlxsw_sp_flood_table',
which is defined per FID family. Instead, it can be an attribute of
'struct mlxsw_sp_fid_family' as all flood tables in the same family are of
the same type. This change will ease the configuration of
'SFMR.flood_bridge_type' which will be added in the next patch.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Under the legacy bridge model, the field 'bridge_type' is used only
in SFGC register, to determine the type of flood table (FID/FID offset).
Under the unified bridge model, it will be used also in SFMR register.
When a BUM packet needs to be flooded, SFGC is used to provide the
'mid_base' for PGT table. The access to SFGC is by
{packet type, bridge type}. Under the unified bridge model, software is
responsible for configuring 'bridge_type' as part of SFMR.
As preparation for the new required configuration, rename
'enum mlxsw_reg_sfgc_bridge_type' to 'enum mlxsw_reg_bridge_type'. Then
it can be used also in SFMR. In addition, align the names of the values to
internal documentation.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Using unified bridge model, RITR register no longer configures the rFID
used for sub-port RIFs. It needs to be created by software via SFMR. Such
FIDs need to be created with a special flood indication using
'SFMR.flood_rsp=1'. It means that for such FIDs, router sub-port flooding
table will be used, this table is configured by firmware.
Set the above mentioned field as part of FID initialization and FID
edition, so then when other fields will be updated in SFMR, this field
will store the correct value and will not be overwritten.
Add 'flood_rsp' variable to 'struct mlxsw_sp_fid_family', set it to true
for rFID and to false for the rest.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
As part of transition to unified bridge model, many different firmware
configurations are done.
Some of the configuration that needs to be done for the unified bridge
model is not valid under the legacy model, and would be rejected by the
firmware. At the same time, the driver cannot switch to the unified bridge
model until all of the code has been converted.
To allow breaking the change into patches, and to not break driver
behavior during the transition, add a boolean variable to indicate bridge
model. Then, forbidden configurations will be skipped using the check -
"if (!mlxsw_sp->ubridge)".
The new variable is temporary for several sets, it will be removed when
firmware will be configured to work with unified bridge model.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The addrconf_verify_rtnl() function uses a big if/elseif/elseif/... block
to categorize each address by what type of attention it needs. An
about-to-expire (RFC 4941) temporary address is one such category, but the
previous elseif branch catches addresses that have already run out their
prefered_lft. This means that if addrconf_verify_rtnl() fails to run in
the necessary time window (i.e. REGEN_ADVANCE time units before the end of
the prefered_lft), the temporary address will never be regenerated, and no
temporary addresses will be available until each one's valid_lft runs out
and manage_tempaddrs() begins anew.
Fix this by moving the entire temporary address regeneration case out of
that block. That block is supposed to implement the "destructive" part of
an address's lifecycle, and regenerating a fresh temporary address is not,
semantically speaking, actually tied to any particular lifecycle stage.
The age test is also changed from `age >= prefered_lft - regen_advance`
to `age + regen_advance >= prefered_lft` instead, to ensure no underflow
occurs if the system administrator increases the regen_advance to a value
greater than the already-set prefered_lft.
Note that this does not fix the problem of addrconf_verify_rtnl() sometimes
not running in time, resulting in the race condition described in RFC 4941
section 3.4 - it only ensures that the address is regenerated. Fixing THAT
problem may require either using jiffies instead of seconds for all time
arithmetic here, or always rounding up when regen_advance is converted to
seconds.
Signed-off-by: Sam Edwards <CFSworks@gmail.com>
Link: https://lore.kernel.org/r/20220623181103.7033-1-CFSworks@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
'vlan_bitmap' is a bitmap and is used as such. So allocate it with
devm_bitmap_zalloc() and its explicit bit size (i.e. VLAN_N_VID).
This avoids the need of the VLAN_BITMAP_SIZE macro which:
- needlessly has a 'nic_dev' parameter
- should be "long" (and not byte) aligned, so that the bitmap semantic
is respected
This is in fact not an issue because VLAN_N_VID is 4096 at the time
being, but devm_bitmap_zalloc() is less verbose and easier to understand.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/6ff7b7d21414240794a77dc2456914412718a145.1656260842.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for ethtool selftest.
e.g.
# ethtool -t DEVNAME
test result like:
The test result is PASS
The test extra info:
Link Test 0
NSP Test 0
Firmware Test 0
Register Test 0
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for VEPA mode of HW bridge.
The default remains VEB mode.
The mode may be configured using ndo_bridge_setlink,
and inspected using ndo_bridge_getlink.
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Delete the redundant word 'set'.
Delete the redundant word 'a'.
Delete the redundant word 'in'.
Found the same error as before.
Signed-off-by: Jilin Yuan <yuanjilin@cdjrlc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following commits added support for printing the real address-
65875073ed ("net: use %px to print skb address in trace_netif_receive_skb")
70713dddf3 ("net_sched: introduce tracepoint trace_qdisc_enqueue()")
851f36e409 ("net_sched: use %px to print skb address in trace_qdisc_dequeue()")
However, tracing the packet traversal shows a mix of hashes and real
addresses. Pasting a sample trace for reference-
ping-14249 [002] ..... 3424.046612: netif_rx_entry: dev=lo napi_id=0x3 queue_mapping=0
skbaddr=00000000dcbed83e vlan_tagged=0 vlan_proto=0x0000 vlan_tci=0x0000 protocol=0x0800
ip_summed=0 hash=0x00000000 l4_hash=0 len=84 data_len=0 truesize=768 mac_header_valid=1
mac_header=-14 nr_frags=0 gso_size=0 gso_type=0x0
ping-14249 [002] ..... 3424.046615: netif_rx: dev=lo skbaddr=ffffff888e5d1000 len=84
Switch the trace print formats to %p for all the events to have a
consistent format of printing the hashed addresses in all cases.
Signed-off-by: Sean Tranchetti <quic_stranche@quicinc.com>
Signed-off-by: Subash Abhinov Kasiviswanathan <quic_subashab@quicinc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde says:
====================
pull-request: can-next 2022-06-25
this is a pull request of 22 patches for net-next/master.
The first 2 patches target the xilinx driver. Srinivas Neeli's patch
adds Transmitter Delay Compensation (TDC) support, a patch by me fixes
a typo.
The next patch is by me and fixes a typo in the m_can driver.
Another patch by me allows the configuration of fixed bit rates
without need for do_set_bittiming callback.
The following 7 patches are by Vincent Mailhol and refactor the
can-dev module and Kbuild, de-inline the can_dropped_invalid_skb()
function, which has grown over the time, and drop outgoing skbs if the
controller is in listen only mode.
Max Staudt's patch fixes a reference in the networking/can.rst
documentation.
Vincent Mailhol provides 2 patches with cleanups for the etas_es58x
driver.
Conor Dooley adds bindings for the mpfs-can to the PolarFire SoC dtsi.
Another patch by me allows the configuration of fixed data bit rates
without need for do_set_data_bittiming callback.
The last 5 patches are by Frank Jungclaus. They prepare the esd_usb
driver to add support for the the CAN-USB/3 device in a later series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Clément Léger says:
====================
net: add support for Renesas RZ/N1 ethernet su
The Renesas RZ/N1 SoCs features an ethernet subsystem which contains
(most notably) a switch, two GMACs, and a MII converter [1]. This
series adds support for the switch and the MII converter.
The MII converter present on this SoC has been represented as a PCS
which sit between the MACs and the PHY. This PCS driver is probed from
the device-tree since it requires to be configured. Indeed the MII
converter also contains the registers that are handling the muxing of
ports (Switch, MAC, HSR, RTOS, etc) internally to the SoC.
The switch driver is based on DSA and exposes 4 ports + 1 CPU
management port. It include basic bridging support as well as FDB and
statistics support.
Link: [1] https://www.renesas.com/us/en/document/mah/rzn1d-group-rzn1s-group-rzn1l-group-users-manual-r-engine-and-ethernet-peripherals
-----
Changes in V9:
- Cover letter:
- Remove comment about RZN1 patches that are now in the master branch.
- Commits:
- Add Vladimir Oltean Reviewed-by
- PCS:
- Add "Depends on OF" for PCS_RZN1_MIIC due to error found by intel
kernel test robot <lkp@intel.com>.
- Check return value of of_property_read_u32() for
"renesas,miic-switch-portin" property before setting conf.
- Return miic_parse_dt() return value in miic_probe() on error
- Switch:
- Add "Depends on OF" for NET_DSA_RZN1_A5PSW due to errors found by
intel kernel test robot <lkp@intel.com>.
- DT:
- Add spaces between switch port and '{'
====================
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After contributing the drivers, volunteer for maintenance and add
myself as the maintainer for Renesas RZ/N1 switch related drivers.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add description for the switch, GMAC2 and MII converter. With these
definitions, the switch port 0 and 1 (MII port 5 and 4) are working on
RZ/N1D-DB board.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add description of the switch that is present on the RZ/N1 SoC. This
description includes ethernet-ports description for all the ports that
are present on the switch along with their connection to the MII
converter ports and to the GMAC for the CPU port.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RZ/N1 SoC includes two MAC named GMACx that are compatible with the
"snps,dwmac" driver. GMAC1 is connected directly to the MII converter
port 1. GMAC2 however can be used as the MAC for the switch CPU
management port or can be muxed to be connected directly to the MII
converter port 2. This commit add description for the GMAC2 which will
be used by the switch description.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the MII converter node which describes the MII converter that is
present on the RZ/N1 SoC.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add statistics support to the rzn1-a5psw driver by implementing the
following dsa_switch_ops callbacks:
- get_sset_count()
- get_strings()
- get_ethtool_stats()
- get_eth_mac_stats()
- get_eth_ctrl_stats()
- get_rmon_stats()
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Renesas RZ/N1 advanced 5 port switch driver. This switch handles 5
ports including 1 CPU management port. A MDIO bus is also exposed by
this switch and allows to communicate with PHYs connected to the ports.
Each switch port (except for the CPU management ports) is connected to
the MII converter.
This driver includes basic bridging support, more support will be added
later (vlan, etc).
Suggested-by: Jean-Pierre Geslin <jean-pierre.geslin@non.se.com>
Suggested-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add bindings for Renesas RZ/N1 Advanced 5 port switch. This switch is
present on Renesas RZ/N1 SoC and was probably provided by MoreThanIP.
This company does not exists anymore and has been bought by Synopsys.
Since this IP can't be find anymore in the Synospsy portfolio, lets use
Renesas as the vendor compatible for this IP.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a PCS driver for the MII converter that is present on the Renesas
RZ/N1 SoC. This MII converter is reponsible for converting MII to
RMII/RGMII or act as a MII pass-trough. Exposing it as a PCS allows to
reuse it in both the switch driver and the stmmac driver. Currently,
this driver only allows the PCS to be used by the dual Cortex-A7
subsystem since the register locking system is not used.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This MII converter can be found on the RZ/N1 processor family. The MII
converter ports are declared as subnodes which are then referenced by
users of the PCS driver such as the switch.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch that is present on the Renesas RZ/N1 SoC uses a specific
VLAN value followed by 6 bytes which contains forwarding configuration.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers might report that they are unable to bridge ports by
returning -EOPNOTSUPP, but still wants to override extack message.
In order to do so, in dsa_slave_changeupper(), if port_bridge_join()
returns -EOPNOTSUPP, check if extack message is set and if so, do not
override it.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Frank Jungclaus says:
====================
All following 5 patches must be seen as preparation for adding support
of the newly available esd CAN-USB/3 to esd_usb2.c.
After having gained some confidence and experience on sending patches
to linux-can@vger.kernel.org, I'll again submit the code changes for
CAN-USB/3 support as step #2.
====================
Link: https://lore.kernel.org/all/20220624190517.2299701-1-frank.jungclaus@esd.eu
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
usbnet uses the work usbnet_deferred_kevent() to perform tasks which may
sleep. On disconnect, completion of the work was originally awaited in
->ndo_stop(). But in 2003, that was moved to ->disconnect() by historic
commit "[PATCH] USB: usbnet, prevent exotic rtnl deadlock":
https://git.kernel.org/tglx/history/c/0f138bbfd83c
The change was made because back then, the kernel's workqueue
implementation did not allow waiting for a single work. One had to wait
for completion of *all* work by calling flush_scheduled_work(), and that
could deadlock when waiting for usbnet_deferred_kevent() with rtnl_mutex
held in ->ndo_stop().
The commit solved one problem but created another: It causes a
use-after-free in USB Ethernet drivers aqc111.c, asix_devices.c,
ax88179_178a.c, ch9200.c and smsc75xx.c:
* If the drivers receive a link change interrupt immediately before
disconnect, they raise EVENT_LINK_RESET in their (non-sleepable)
->status() callback and schedule usbnet_deferred_kevent().
* usbnet_deferred_kevent() invokes the driver's ->link_reset() callback,
which calls netif_carrier_{on,off}().
* That in turn schedules the work linkwatch_event().
Because usbnet_deferred_kevent() is awaited after unregister_netdev(),
netif_carrier_{on,off}() may operate on an unregistered netdev and
linkwatch_event() may run after free_netdev(), causing a use-after-free.
In 2010, usbnet was changed to only wait for a single instance of
usbnet_deferred_kevent() instead of *all* work by commit 23f333a2bf
("drivers/net: don't use flush_scheduled_work()").
Unfortunately the commit neglected to move the wait back to
->ndo_stop(). Rectify that omission at long last.
Reported-by: Jann Horn <jannh@google.com>
Link: https://lore.kernel.org/netdev/CAG48ez0MHBbENX5gCdHAUXZ7h7s20LnepBF-pa5M=7Bi-jZrEA@mail.gmail.com/
Reported-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/netdev/20220315113841.GA22337@pengutronix.de/
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org
Acked-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/d1c87ebe9fc502bffcd1576e238d685ad08321e4.1655987888.git.lukas@wunner.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
