After the device is initialized, it runs ATI (calibration) during
which it cannot readily respond to I2C communication. To keep the
open and close callbacks from writing to the device too soon, the
driver waits 100 ms before returning from probe.
The vendor reports that ATI may actually take up to 250 ms to run
(including margin), so increase the delay accordingly. Update the
comments to clarify the reason for the delay as well.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/1611002626-5889-9-git-send-email-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of relying on firmware to enable important register fields
and performing read-modify-write operations to additionally enable
the fields the driver cares about, it's much simpler just to write
all of the pertinent fields explicitly.
This avoids an unnecessary register read operation at start-up and
makes way for the iqs5xx_read_byte() helper to be dropped.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/1611002626-5889-8-git-send-email-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The present implementation manipulates axis swap and inversion fields
in the device to more or less duplicate what touchscreen_report_pos()
does. The resulting logic is convoluted and difficult to follow.
Instead report the maximum X and Y coordinates in earnest as they are
read from the device, then let touchscreen_parse_properties() fix the
axes up as necessary. Finally, use touchscreen_report_pos() to report
the transformed coordinates.
Last but not least, the maximum X and Y coordinates are not functions
of the number of rows/columns that comprise the touch surface. Either
coordinate is simply limited to 1 below what is reported for absolute
X or Y coordinates when no fingers are present (0xFFFF).
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/1611002626-5889-7-git-send-email-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The device may be inadvertently reset during runtime in the event
of ESD strike, etc. To protect against this case, acknowledge the
SHOW_RESET interrupt and re-initialize the device.
To facilitate this change, expand the range of registers that are
read in the interrupt handler to include the system status fields.
Also, update the unrelated (but nearby) SUSPEND register field to
use the BIT() macro. The remaining register fields are cleaned up
in another patch.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/1611002626-5889-6-git-send-email-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The bootloader NAK's all I2C communication after the first 64-byte
bulk write if the bus frequency is equal to 400 kHz. This prevents
the platform from pushing updated firmware to the device.
The vendor's USB bootloader programming dongle appears to insert a
delay between the "open" command and the first 64-byte bulk write.
Adding a similar delay to the driver seems to eliminate the issue.
Furthermore, the dongle does not access the bootloader immediately
after powering up the device. Follow suit by adding a delay before
the "open" command to avoid wasted retries at 400 kHz.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/1611002626-5889-4-git-send-email-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
After user space writes the fw_file attribute to push new firmware
to the device, the driver calls iqs5xx_dev_init() to re-initialize
the device with the updated firmware or recover the device in case
the update failed.
In the case of the latter, however, iqs5xx_fw_file_write() returns
zero (success) so long as iqs5xx_dev_init() does not fail, and any
error encountered during the update process is lost. Solve this by
saving the error before calling iqs5xx_dev_init().
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/1611002626-5889-3-git-send-email-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Copyrights are generally followed by the name of a person or a
company (i.e. the copyright holder) but that was not done here.
Fix this by squashing the 'copyright' and 'author' lines.
Also, trim some leading whitespace ahead of the parameters for
the fw_file_store() function and re-align them for readability.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/1611002626-5889-2-git-send-email-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add ELAN KTF3624 touchscreen support to the elants_i2c driver.
The eKTF3624 TS is found on a series of ASUS Transformer tablet devices,
Nexus 7 tablet and etc. The firmware interface of eKTF3624 is nearly
identical to eKTH3500, which is already supported by the driver.
The minor differences of the firmware interface are now handled by
the driver. The eKTF3624 support was tested on ASUS Transformer TF700T,
TF300T and Nexus 7 tablets.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210124195414.27333-1-digetx@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Convert multiple full duplex transfers in to a single transfer to reduce
CPU load.
Current driver version support following filtering modes:
- ads7846_no_filter() - not filtered
- ads7846_debounce_filter() - driver specific debounce filter
- pdata->filter - platform specific debounce filter (do any platform
provides such filter?)
Without filter this HW is not really usable, since the physic of
resistive touchscreen can provide some bounce effects. With driver internal
filter, we have constant amount of retries + debounce retries if some anomaly
was detected.
High amount of tiny SPI transfers is the primer reason of high CPU load
and interrupt frequency.
This patch create one SPI transfer with all fields and not optional retires. If
bounce anomaly was detected, we will make more transfer if needed.
Without this patch, we will get about 10% CPU load on iMX6S on pen-down event.
For example by holding stylus on the screen.
With this patch, depending in the amount of retries, the CPU load will
be 1% with "ti,debounce-rep = <3>".
One buffer transfer allows us to use PIO FIFO or DMA engine, depending
on the platform.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20201110085041.16303-3-o.rempel@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Dmitry requested to keep these around for the purposes of documentation.
Fixes the following W=1 kernel build warning(s):
drivers/input/touchscreen/melfas_mip4.c: In function ‘mip4_report_touch’:
drivers/input/touchscreen/melfas_mip4.c:474:5: warning: variable ‘size’ set but not used [-Wunused-but-set-variable]
drivers/input/touchscreen/melfas_mip4.c:472:5: warning: variable ‘pressure_stage’ set but not used [-Wunused-but-set-variable]
drivers/input/touchscreen/melfas_mip4.c:469:7: warning: variable ‘palm’ set but not used [-Wunused-but-set-variable]
drivers/input/touchscreen/melfas_mip4.c:468:7: warning: variable ‘hover’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210114152323.2382283-3-lee.jones@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We are still missing handling for errata i689 related issues for the
case where we never see a key up interrupt for the last pressed key.
To fix the issue, we must scan the key state again after the keyboard
controller has idled to check if a key up event was missed. This is
described in the omap4 silicon errata documentation for Errata ID i689
"1.32 Keyboard Key Up Event Can Be Missed":
"When a key is released for a time shorter than the debounce time,
in-between 2 key press (KP1 and KP2), the keyboard state machine will go
to idle mode and will never detect the key release (after KP1, and also
after KP2), and thus will never generate a new IRQ indicating the key
release."
We can use PM runtime autosuspend features to check the keyboard state
after it enters idle.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/X/vrygoBxzGyXhfc@atomide.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Implement PM runtime autosuspend support to prepare for adding handling to
clear stuck last pressed key in the following patches. The hardware has
support for autoidle and can wake up to keypress events.
Let's also update omap4_keypad_probe() to use dev instead of &pdev->dev
since we already have it from the earlier changes.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/X/vqCs5/EDURprAJ@atomide.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Because of errata i689 the keyboard can idle with state where no key
up interrupts are seen until after the next key press.
This means we need to first check for any lost key up events before
scanning for new down events.
For example, rapidly pressing shift-shift-j can sometimes produce a J
instead of j. Let's fix the issue by scanning the keyboard in two
phases. First we scan for any key up events that we may have missed,
and then we scan for key down events.
Let's also simplify things with for_each_set_bit() as suggested by
Dmitry Torokhov <dmitry.torokhov@gmail.com>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210110190529.46135-3-tony@atomide.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
gcc -Warray-bounds warns about a serious bug in
cyapa_pip_retrieve_data_structure:
drivers/input/mouse/cyapa_gen6.c: In function 'cyapa_pip_retrieve_data_structure.constprop':
include/linux/unaligned/access_ok.h:40:17: warning: array subscript -1 is outside array bounds of 'struct retrieve_data_struct_cmd[1]' [-Warray-bounds]
40 | *((__le16 *)p) = cpu_to_le16(val);
drivers/input/mouse/cyapa_gen6.c:569:13: note: while referencing 'cmd'
569 | } __packed cmd;
| ^~~
Apparently the '-2' was added to the pointer instead of the value,
writing garbage into the stack next to this variable.
Fixes: c2c06c41f7 ("Input: cyapa - add gen6 device module support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20201026161332.3708389-1-arnd@kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If device is set up as a wakeup source, I2C core configures the interrupt
line as wake IRQ and PM core automatically configures it for waking up the
system on system suspend transition, so we do not have to explicitly call
enable_irq_wake() and disable_irq_wake() in suspend/resume.
Link: https://lore.kernel.org/r/20201120073920.3214492-2-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There are some version of Elan trackpads that send incorrect data when
in SMbus mode, unless they are switched to use 0x5f reports instead of
standard 0x5e. This patch implements querying device to retrieve chips
identifying data, and switching it, when needed to the alternative
report.
Signed-off-by: Jingle Wu <jingle.wu@emc.com.tw>
Link: https://lore.kernel.org/r/20201211071531.32413-1-jingle.wu@emc.com.tw
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Tested-by: Ronald Tschalär <ronald@innovation.ch>
Reviewed-by: Ronald Tschalär <ronald@innovation.ch>
Link: https://lore.kernel.org/r/20200227124534.23399-1-sergiu.cuciurean@analog.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Link: https://lore.kernel.org/r/20200227130336.27042-1-sergiu.cuciurean@analog.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Link: https://lore.kernel.org/r/20200228104508.15564-1-sergiu.cuciurean@analog.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
