This is to disable semaphore usage when on vGPU for now. Unfortunately
GVT-g hasn't fully enabled semaphore usage yet, so current guest with
semaphore use would cause vGPU failure.
Although current semaphore failure with vGPU can be simply resolved by
allowing cmd parser to accept MI_SEMAPHORE_WAIT command with address
audit, we're checking general usage of semaphore and how we should
handle it properly for virtualization in consider of function and
security concern. So we decide to request to disable it for now in
guest driver. Once GVT could support it, we would add new compat bit
to turn it on.
Fixes: e886196469 ("drm/i915: Use HW semaphores for inter-engine synchronisation on gen8+") #vgpu
Cc: Kevin Tian <kevin.tian@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190327090636.3547-1-zhenyuw@linux.intel.com
Update the DP MSA MISC bits for fastsets. This is needed
when we change between limited and full range RGB output.
On HSW+ changing limited_range does not currently result in a
full modeset since we have don't have the readout code for it
(for DP we could, and probably should, readout from TRANS_MSA_MISC
itself, for HDMI we would have to rely on the infoframe). So
the PIPE_CONF_CHECK() is only performed for pre-HSW platforms.
That means any change in the value will result in a fastset
instead. Fortunately there is no prohibition to changing
TRANS_MSA_MISC dynamically, so it looks like we can legally do
fastsets for this.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326142556.21176-5-ville.syrjala@linux.intel.com
When building with ARCH=i386, readq and writeq are not defined,
resulting in:
intel_uncore.h: In function ‘__raw_uncore_read64’:
intel_uncore.h:257:9: error: implicit declaration of function ‘readq’;
did you mean ‘readl’? [-Werror=implicit-function-declaration]
return read##s__(uncore->regs + i915_mmio_reg_offset(reg)); \
^
and:
intel_uncore.h: In function ‘__raw_uncore_write64’:
intel_uncore.h:264:2: error: implicit declaration of function ‘writeq’;
did you mean ‘writel’? [-Werror=implicit-function-declaration]
write##s__(val, uncore->regs + i915_mmio_reg_offset(reg)); \
^
Add the io-64-nonatomic-lo-hi include to have readq and writeq available
for all builds. This header internally includes linux/io.h, so the
native readq and writeq definitions will be used when available.
Fixes: 6cc5ca7688 ("drm/i915: rename raw reg access functions")
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326233817.5417-1-daniele.ceraolospurio@intel.com
Iterate over child devices instead of ports in parse_ddi_ports() to
initialize ddi_port_info. We'll eventually need to decide some stuff
based on the child device order, which may be different from the port
order.
As a bonus, this allows better abstractions for e.g. dvo port mapping.
There's a subtle change in the DDC pin and AUX channel sanitization as
we change the order. Otherwise, this should not change behaviour.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322121008.4456-1-jani.nikula@intel.com
The AGPBUSY thing doesn't work on i945gm anymore. This means
the gmch is incapable of waking the CPU from C3 when an interrupt
is generated. The interrupts just get postponed indefinitely until
something wakes up the CPU. This is rather annoying for vblank
interrupts as we are unable to maintain a steady framerate
unless the machine is sufficiently loaded to stay out of C3.
To combat this let's use pm_qos to prevent C3 whenever vblank
interrupts are enabled. To maintain reasonable amount of powersaving
we will attempt to limit this to C3 only while leaving C1 and C2
enabled.
v2: Use READ_ONCE() (Chris)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30364
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322180804.3300-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Some monitors apparently forget to mark any mode as preferred in the
EDID. In this particular case we have a very generic looking ID
"PNP Model 0 Serial Number 4" / "LVDS 800x600" so a specific quirk
doesn't seem particularly wise. Also the quirk we have
(EDID_QUIRK_FIRST_DETAILED_PREFERRED) is actually defunct so we'd
have to fix it first.
When there is no preferred mode we currently fall back to the VBT.
That approach fails us here as the VBT mode is 1024x768 whereas
the panel resolution is 800x600. So instead of falling back to the
VBT when there is no preferred mode let's just pick the first
probed mode. Only if the EDID provided no modes we fall back to
the VBT.
For this machine the VBIOS would appear to select the 800x600
60Hz EST mode rather than the first detailed mode (which is
the new fallback will pick). The two modes differ only by
having opposite sync polarities, which does not seem to matter
to the panel in question.
v2: Make sure the probed_modes list is not empty
Cc: Adam Jackson <ajax@redhat.com>
Cc: Roberto Viola <cagnulein@gmail.com>
Tested-by: Roberto Viola <cagnulein@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=109780
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190321132446.22394-2-ville.syrjala@linux.intel.com
Reviewed-by: Adam Jackson <ajax@redhat.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Previously, our view has been always to run the engines independently
within a context. (Multiple engines happened before we had contexts and
timelines, so they always operated independently and that behaviour
persisted into contexts.) However, at the user level the context often
represents a single timeline (e.g. GL contexts) and userspace must
ensure that the individual engines are serialised to present that
ordering to the client (or forgot about this detail entirely and hope no
one notices - a fair ploy if the client can only directly control one
engine themselves ;)
In the next patch, we will want to construct a set of engines that
operate as one, that have a single timeline interwoven between them, to
present a single virtual engine to the user. (They submit to the virtual
engine, then we decide which engine to execute on based.)
To that end, we want to be able to create contexts which have a single
timeline (fence context) shared between all engines, rather than multiple
timelines.
v2: Move the specialised timeline ordering to its own function.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322092325.5883-4-chris@chris-wilson.co.uk
It can be useful to have a single ioctl to create a context with all
the initial parameters instead of a series of create + setparam + setparam
ioctls. This extension to create context allows any of the parameters
to be passed in as a linked list to be applied to the newly constructed
context.
v2: Make a local copy of user setparam (Tvrtko)
v3: Use flags to detect availability of extension interface
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322092325.5883-3-chris@chris-wilson.co.uk
In preparation to making the ppGTT binding for a context explicit (to
facilitate reusing the same ppGTT between different contexts), allow the
user to create and destroy named ppGTT.
v2: Replace global barrier for swapping over the ppgtt and tlbs with a
local context barrier (Tvrtko)
v3: serialise with struct_mutex; it's lazy but required dammit
v4: Rewrite igt_ctx_shared_exec to be more different (aimed to be more
similarly, turned out different!)
v5: Fix up test unwind for aliasing-ppgtt (snb)
v6: Tighten language for uapi struct drm_i915_gem_vm_control.
v7: Patch the context image for runtime ppgtt switching!
Testcase: igt/gem_vm_create
Testcase: igt/gem_ctx_param/vm
Testcase: igt/gem_ctx_clone/vm
Testcase: igt/gem_ctx_shared
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322092325.5883-2-chris@chris-wilson.co.uk
