compute_intercept_slope() is called from calibrate_8960() (in tsens-8960.c)
as compute_intercept_slope(priv, p1, NULL, ONE_PT_CALIB) which lead to null
pointer dereference (if DEBUG or DYNAMIC_DEBUG set).
Fix this bug by adding null pointer check.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: dfc1193d4d ("thermal/drivers/tsens: Replace custom 8960 apis with generic apis")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240411114021.12203-1-amishin@t-argos.ru
The initial driver used a formula to approximate the temperature and
register values reversed engineered from an out-of-tree BSP driver. This
was needed as the datasheet at the time did not contain any information
on how to do this. Later Gen3 (Rev 2.30) and Gen4 (all) now contains
this information.
Update the approximation formula to use the datasheet's information
instead of the reversed-engineered one.
On an idle M3-N without fused calibration values for PTAT and THCODE the
old formula reports,
zone0: 52000
zone1: 53000
zone2: 52500
While the new formula under the same circumstances reports,
zone0: 52500
zone1: 54000
zone2: 54000
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240327133013.3982199-3-niklas.soderlund+renesas@ragnatech.se
The calculated Tj_T constant is calculated from the PTAT data either
read from the first TSC zone on the device if calibration data is fused,
or from fallback values in the driver itself. The value calculated is
shared among all TSC zones.
Move the Tj_T constant to the shared private data structure instead of
duplicating it in each TSC private data. This requires adding a pointer
to the shared data to the TSC private data structure. This back pointer
make it easier to further rework the temperature conversion logic.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240327133013.3982199-2-niklas.soderlund+renesas@ragnatech.se
The count field in struct trip_stats, representing the number of times
the zone temperature was above the trip point, needs to be incremented
in thermal_debug_tz_trip_up(), for two reasons.
First, if a trip point is crossed on the way up for the first time,
thermal_debug_update_temp() called from update_temperature() does
not see it because it has not been added to trips_crossed[] array
in the thermal zone's struct tz_debugfs object yet. Therefore, when
thermal_debug_tz_trip_up() is called after that, the trip point's
count value is 0, and the attempt to divide by it during the average
temperature computation leads to a divide error which causes the kernel
to crash. Setting the count to 1 before the division by incrementing it
fixes this problem.
Second, if a trip point is crossed on the way up, but it has been
crossed on the way up already before, its count value needs to be
incremented to make a record of the fact that the zone temperature is
above the trip now. Without doing that, if the mitigations applied
after crossing the trip cause the zone temperature to drop below its
threshold, the count will not be updated for this episode at all and
the average temperature in the trip statistics record will be somewhat
higher than it should be.
Fixes: 7ef01f228c ("thermal/debugfs: Add thermal debugfs information for mitigation episodes")
Cc :6.8+ <stable@vger.kernel.org> # 6.8+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull sysfs fix from Al Viro:
"Get rid of lockdep false positives around sysfs/overlayfs
syzbot has uncovered a class of lockdep false positives for setups
with sysfs being one of the backing layers in overlayfs. The root
cause is that of->mutex allocated when opening a sysfs file read-only
(which overlayfs might do) is confused with of->mutex of a file opened
writable (held in write to sysfs file, which overlayfs won't do).
Assigning them separate lockdep classes fixes that bunch and it's
obviously safe"
* tag 'pull-sysfs-annotation-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
kernfs: annotate different lockdep class for of->mutex of writable files
Pull misc x86 fixes from Ingo Molnar:
- Follow up fixes for the BHI mitigations code
- Fix !SPECULATION_MITIGATIONS bug not turning off mitigations as
expected
- Work around an APIC emulation bug when the kernel is built with Clang
and run as a SEV guest
- Follow up x86 topology fixes
* tag 'x86-urgent-2024-04-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu/amd: Move TOPOEXT enablement into the topology parser
x86/cpu/amd: Make the NODEID_MSR union actually work
x86/cpu/amd: Make the CPUID 0x80000008 parser correct
x86/bugs: Replace CONFIG_SPECTRE_BHI_{ON,OFF} with CONFIG_MITIGATION_SPECTRE_BHI
x86/bugs: Remove CONFIG_BHI_MITIGATION_AUTO and spectre_bhi=auto
x86/bugs: Clarify that syscall hardening isn't a BHI mitigation
x86/bugs: Fix BHI handling of RRSBA
x86/bugs: Rename various 'ia32_cap' variables to 'x86_arch_cap_msr'
x86/bugs: Cache the value of MSR_IA32_ARCH_CAPABILITIES
x86/bugs: Fix BHI documentation
x86/cpu: Actually turn off mitigations by default for SPECULATION_MITIGATIONS=n
x86/topology: Don't update cpu_possible_map in topo_set_cpuids()
x86/bugs: Fix return type of spectre_bhi_state()
x86/apic: Force native_apic_mem_read() to use the MOV instruction
Pull perf event fix from Ingo Molnar:
"Fix the x86 PMU multi-counter code returning invalid data in certain
circumstances"
* tag 'perf-urgent-2024-04-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86: Fix out of range data
Pull locking fix from Ingo Molnar:
"Fix a PREEMPT_RT build bug"
* tag 'locking-urgent-2024-04-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking: Make rwsem_assert_held_write_nolockdep() build with PREEMPT_RT=y
Pull irq fix from Ingo Molnar:
"Fix a bug in the GIC irqchip driver"
* tag 'irq-urgent-2024-04-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3-its: Fix VSYNC referencing an unmapped VPE on GIC v4.1
Pull virtio bugfixes from Michael Tsirkin:
"Some small, obvious (in hindsight) bugfixes:
- new ioctl in vhost-vdpa has a wrong # - not too late to fix
- vhost has apparently been lacking an smp_rmb() - due to code
duplication :( The duplication will be fixed in the next merge
cycle, this is a minimal fix
- an error message in vhost talks about guest moving used index -
which of course never happens, guest only ever moves the available
index
- i2c-virtio didn't set the driver owner so it did not get refcounted
correctly"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vhost: correct misleading printing information
vhost-vdpa: change ioctl # for VDPA_GET_VRING_SIZE
virtio: store owner from modules with register_virtio_driver()
vhost: Add smp_rmb() in vhost_enable_notify()
vhost: Add smp_rmb() in vhost_vq_avail_empty()
Pull dma-mapping fixes from Christoph Hellwig:
- fix up swiotlb buffer padding even more (Petr Tesarik)
- fix for partial dma_sync on swiotlb (Michael Kelley)
- swiotlb debugfs fix (Dexuan Cui)
* tag 'dma-maping-6.9-2024-04-14' of git://git.infradead.org/users/hch/dma-mapping:
swiotlb: do not set total_used to 0 in swiotlb_create_debugfs_files()
swiotlb: fix swiotlb_bounce() to do partial sync's correctly
swiotlb: extend buffer pre-padding to alloc_align_mask if necessary
The writable file /sys/power/resume may call vfs lookup helpers for
arbitrary paths and readonly files can be read by overlayfs from vfs
helpers when sysfs is a lower layer of overalyfs.
To avoid a lockdep warning of circular dependency between overlayfs
inode lock and kernfs of->mutex, use a different lockdep class for
writable and readonly kernfs files.
Reported-by: syzbot+9a5b0ced8b1bfb238b56@syzkaller.appspotmail.com
Fixes: 0fedefd4c4 ("kernfs: sysfs: support custom llseek method for sysfs entries")
Suggested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull ata fixes from Damien Le Moal:
- Add the mask_port_map parameter to the ahci driver. This is a
follow-up to the recent snafu with the ASMedia controller and its
virtual port hidding port-multiplier devices. As ASMedia confirmed
that there is no way to determine if these slow-to-probe virtual
ports are actually representing the ports of a port-multiplier
devices, this new parameter allow masking ports to significantly
speed up probing during system boot, resulting in shorter boot times.
- A fix for an incorrect handling of a port unlock in
ata_scsi_dev_rescan().
- Allow command duration limits to be detected for ACS-4 devices are
there are such devices out in the field.
* tag 'ata-6.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux:
ata: libata-core: Allow command duration limits detection for ACS-4 drives
ata: libata-scsi: Fix ata_scsi_dev_rescan() error path
ata: ahci: Add mask_port_map module parameter
Pull zonefs fix from Damien Le Moal:
- Suppress a coccicheck warning using str_plural()
* tag 'zonefs-6.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs:
zonefs: Use str_plural() to fix Coccinelle warning
Pull smb client fixes from Steve French:
- fix for oops in cifs_get_fattr of deleted files
- fix for the remote open counter going negative in some directory
lease cases
- fix for mkfifo to instantiate dentry to avoid possible crash
- important fix to allow handling key rotation for mount and remount
(ie cases that are becoming more common when password that was used
for the mount will expire soon but will be replaced by new password)
* tag 'v6.9-rc3-SMB3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
smb3: fix broken reconnect when password changing on the server by allowing password rotation
smb: client: instantiate when creating SFU files
smb3: fix Open files on server counter going negative
smb: client: fix NULL ptr deref in cifs_mark_open_handles_for_deleted_file()
Even though the command duration limits (CDL) feature was first added
in ACS-5 (major version 12), there are some ACS-4 (major version 11)
drives that implement CDL as well.
IDENTIFY_DEVICE, SUPPORTED_CAPABILITIES, and CURRENT_SETTINGS log pages
are mandatory in the ACS-4 standard so it should be safe to read these
log pages on older drives implementing the ACS-4 standard.
Fixes: 62e4a60e0c ("scsi: ata: libata: Detect support for command duration limits")
Cc: stable@vger.kernel.org
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Commit 0c76106cb9 ("scsi: sd: Fix TCG OPAL unlock on system resume")
incorrectly handles failures of scsi_resume_device() in
ata_scsi_dev_rescan(), leading to a double call to
spin_unlock_irqrestore() to unlock a device port. Fix this by redefining
the goto labels used in case of errors and only unlock the port
scsi_scan_mutex when scsi_resume_device() fails.
Bug found with the Smatch static checker warning:
drivers/ata/libata-scsi.c:4774 ata_scsi_dev_rescan()
error: double unlocked 'ap->lock' (orig line 4757)
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Fixes: 0c76106cb9 ("scsi: sd: Fix TCG OPAL unlock on system resume")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Pull arm64 fix from Catalin Marinas:
"Fix the TLBI RANGE operand calculation causing live migration under
KVM/arm64 to miss dirty pages due to stale TLB entries"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: tlb: Fix TLBI RANGE operand
Pull SoC fixes from Arnd Bergmann:
"The device tree changes this time are all for NXP i.MX platforms,
addressing issues with clocks and regulators on i.MX7 and i.MX8.
The old OMAP2 based Nokia N8x0 tablet get a couple of code fixes for
regressions that came in.
The ARM SCMI and FF-A firmware interfaces get a couple of minor bug
fixes.
A regression fix for RISC-V cache management addresses a problem with
probe order on Sifive cores"
* tag 'soc-fixes-6.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (23 commits)
MAINTAINERS: Change Krzysztof Kozlowski's email address
arm64: dts: imx8qm-ss-dma: fix can lpcg indices
arm64: dts: imx8-ss-dma: fix can lpcg indices
arm64: dts: imx8-ss-dma: fix adc lpcg indices
arm64: dts: imx8-ss-dma: fix pwm lpcg indices
arm64: dts: imx8-ss-dma: fix spi lpcg indices
arm64: dts: imx8-ss-conn: fix usb lpcg indices
arm64: dts: imx8-ss-lsio: fix pwm lpcg indices
ARM: dts: imx7s-warp: Pass OV2680 link-frequencies
ARM: dts: imx7-mba7: Use 'no-mmc' property
arm64: dts: imx8-ss-conn: fix usdhc wrong lpcg clock order
arm64: dts: freescale: imx8mp-venice-gw73xx-2x: fix USB vbus regulator
arm64: dts: freescale: imx8mp-venice-gw72xx-2x: fix USB vbus regulator
cache: sifive_ccache: Partially convert to a platform driver
firmware: arm_scmi: Make raw debugfs entries non-seekable
firmware: arm_scmi: Fix wrong fastchannel initialization
firmware: arm_ffa: Fix the partition ID check in ffa_notification_info_get()
ARM: OMAP2+: fix USB regression on Nokia N8x0
mmc: omap: restore original power up/down steps
mmc: omap: fix deferred probe
...
Pull iommu fixes from Joerg Roedel:
- Intel VT-d Fixes:
- Allocate local memory for PRQ page
- Fix WARN_ON in iommu probe path
- Fix wrong use of pasid config
- AMD IOMMU Fixes:
- Lock inversion fix
- Log message severity fix
- Disable SNP when v2 page-tables are used
- Mediatek driver:
- Fix module autoloading
* tag 'iommu-fixes-v6.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Change log message severity
iommu/vt-d: Fix WARN_ON in iommu probe path
iommu/vt-d: Allocate local memory for page request queue
iommu/vt-d: Fix wrong use of pasid config
iommu: mtk: fix module autoloading
iommu/amd: Do not enable SNP when V2 page table is enabled
iommu/amd: Fix possible irq lock inversion dependency issue
Pull pci fixes from Bjorn Helgaas:
- Revert a quirk that prevented Secondary Bus Reset for LSI / Agere
FW643.
We thought the device was broken, but the reset does work correctly
on other platforms, and the reset avoids leaking data out of VMs
(Bjorn Helgaas)
- Update MAINTAINERS to reflect that Gustavo Pimentel is no longer
reachable (Manivannan Sadhasivam)
* tag 'pci-v6.9-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
Revert "PCI: Mark LSI FW643 to avoid bus reset"
MAINTAINERS: Drop Gustavo Pimentel as PCI DWC Maintainer
Pull block fixes from Jens Axboe:
- MD pull request via Song:
- UAF fix (Yu)
- Avoid out-of-bounds shift in blk-iocost (Rik)
- Fix for q->blkg_list corruption (Ming)
- Relax virt boundary mask/size segment checking (Ming)
* tag 'block-6.9-20240412' of git://git.kernel.dk/linux:
block: fix that blk_time_get_ns() doesn't update time after schedule
block: allow device to have both virt_boundary_mask and max segment size
block: fix q->blkg_list corruption during disk rebind
blk-iocost: avoid out of bounds shift
raid1: fix use-after-free for original bio in raid1_write_request()
Pull io_uring fixes from Jens Axboe:
- Fix for sigmask restoring while waiting for events (Alexey)
- Typo fix in comment (Haiyue)
- Fix for a msg_control retstore on SEND_ZC retries (Pavel)
* tag 'io_uring-6.9-20240412' of git://git.kernel.dk/linux:
io-uring: correct typo in comment for IOU_F_TWQ_LAZY_WAKE
io_uring/net: restore msg_control on sendzc retry
io_uring: Fix io_cqring_wait() not restoring sigmask on get_timespec64() failure
Pull ceph fixes from Ilya Dryomov:
"Two CephFS fixes marked for stable and a MAINTAINERS update"
* tag 'ceph-for-6.9-rc4' of https://github.com/ceph/ceph-client:
MAINTAINERS: remove myself as a Reviewer for Ceph
ceph: switch to use cap_delay_lock for the unlink delay list
ceph: redirty page before returning AOP_WRITEPAGE_ACTIVATE
Commit d96c36004e ("tracing: Fix FTRACE_RECORD_RECURSION_SIZE Kconfig
entry") removed a hidden tab because it apparently showed breakage in
some third-party kernel config parsing tool.
It wasn't clear what tool it was, but let's make sure it gets fixed.
Because if you can't parse tabs as whitespace, you should not be parsing
the kernel Kconfig files.
In fact, let's make such breakage more obvious than some esoteric ftrace
record size option. If you can't parse tabs, you can't have page sizes.
Yes, tab-vs-space confusion is sadly a traditional Unix thing, and
'make' is famous for being broken in this regard. But no, that does not
mean that it's ok.
I'd add more random tabs to our Kconfig files, but I don't want to make
things uglier than necessary. But it *might* bbe necessary if it turns
out we see more of this kind of silly tooling.
Fixes: d96c36004e ("tracing: Fix FTRACE_RECORD_RECURSION_SIZE Kconfig entry")
Link: https://lore.kernel.org/lkml/CAHk-=wj-hLLN_t_m5OL4dXLaxvXKy_axuoJYXif7iczbfgAevQ@mail.gmail.com/
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull tracing fixes from Steven Rostedt:
- Fix the buffer_percent accounting as it is dependent on three
variables:
1) pages_read - number of subbuffers read
2) pages_lost - number of subbuffers lost due to overwrite
3) pages_touched - number of pages that a writer entered
These three counters only increment, and to know how many active
pages there are on the buffer at any given time, the pages_read and
pages_lost are subtracted from pages_touched.
But the pages touched was incremented whenever any writer went to the
next subbuffer even if it wasn't the only one, so it was incremented
more than it should be causing the counter for how many subbuffers
currently have content incorrect, which caused the buffer_percent
that holds waiters until the ring buffer is filled to a given
percentage to wake up early.
- Fix warning of unused functions when PERF_EVENTS is not configured in
- Replace bad tab with space in Kconfig for FTRACE_RECORD_RECURSION_SIZE
- Fix to some kerneldoc function comments in eventfs code.
* tag 'trace-v6.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
ring-buffer: Only update pages_touched when a new page is touched
tracing: hide unused ftrace_event_id_fops
tracing: Fix FTRACE_RECORD_RECURSION_SIZE Kconfig entry
eventfs: Fix kernel-doc comments to functions
Pull MIPS fix from Thomas Bogendoerfer:
"Fix for syscall_get_nr() to make it work even if tracing is disabled"
* tag 'mips-fixes_6.9_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: scall: Save thread_info.syscall unconditionally on entry
Pull drm fixes from Dave Airlie:
"Looks like everyone woke up after holidays, this weeks pull has a
bunch of stuff all over, 2 weeks worth of amdgpu is a lot of it, then
i915/xe have a few, a bunch of msm fixes, then some scattered driver
fixes.
I expect things will settle down for rc5.
client:
- Protect connector modes with mode_config mutex
ast:
- Fix soft lockup
host1x:
- Do not setup DMA for virtual addresses
ivpu:
- Fix deadlock in context_xa
- PCI fixes
- Fixes to error handling
nouveau:
- gsp: Fix OOB access
- Fix casting
panfrost:
- Fix error path in MMU code
qxl:
- Revert "drm/qxl: simplify qxl_fence_wait"
vmwgfx:
- Enable DMA for SEV mappings
i915:
- Couple CDCLK programming fixes
- HDCP related fix
- 4 Bigjoiner related fixes
- Fix for a circular locking around GuC on reset+wedged case
xe:
- Fix double display mutex initializations
- Fix u32 -> u64 implicit conversions
- Fix RING_CONTEXT_CONTROL not marked as masked
msm:
- DP refcount leak fix on disconnect
- Add missing newlines to prints in msm_fb and msm_kms
- fix dpu debugfs entry permissions
- Fix the interface table for the catalog of X1E80100
- fix irq message printing
- Bindings fix to add DP node as child of mdss for mdss node
- Minor typo fix in DP driver API which handles port status change
- fix CHRASHDUMP_READ()
- fix HHB (highest bank bit) for a619 to fix UBWC corruption
amdgpu:
- GPU reset fixes
- Fix some confusing logging
- UMSCH fix
- Aborted suspend fix
- DCN 3.5 fixes
- S4 fix
- MES logging fixes
- SMU 14 fixes
- SDMA 4.4.2 fix
- KASAN fix
- SMU 13.0.10 fix
- VCN partition fix
- GFX11 fixes
- DWB fixes
- Plane handling fix
- FAMS fix
- DCN 3.1.6 fix
- VSC SDP fixes
- OLED panel fix
- GFX 11.5 fix
amdkfd:
- GPU reset fixes
- fix ioctl integer overflow"
* tag 'drm-fixes-2024-04-12' of https://gitlab.freedesktop.org/drm/kernel: (65 commits)
amdkfd: use calloc instead of kzalloc to avoid integer overflow
drm/xe: Label RING_CONTEXT_CONTROL as masked
drm/xe/xe_migrate: Cast to output precision before multiplying operands
drm/xe/hwmon: Cast result to output precision on left shift of operand
drm/xe/display: Fix double mutex initialization
drm/amdgpu: differentiate external rev id for gfx 11.5.0
drm/amd/display: Adjust dprefclk by down spread percentage.
drm/amd/display: Set VSC SDP Colorimetry same way for MST and SST
drm/amd/display: Program VSC SDP colorimetry for all DP sinks >= 1.4
drm/amd/display: fix disable otg wa logic in DCN316
drm/amd/display: Do not recursively call manual trigger programming
drm/amd/display: always reset ODM mode in context when adding first plane
drm/amdgpu: fix incorrect number of active RBs for gfx11
drm/amd/display: Return max resolution supported by DWB
amd/amdkfd: sync all devices to wait all processes being evicted
drm/amdgpu: clear set_q_mode_offs when VM changed
drm/amdgpu: Fix VCN allocation in CPX partition
drm/amd/pm: fix the high voltage issue after unload
drm/amd/display: Skip on writeback when it's not applicable
drm/amdgpu: implement IRQ_STATE_ENABLE for SDMA v4.4.2
...
While monitoring the throttle time of IO from iocost, it's found that
such time is always zero after the io_schedule() from ioc_rqos_throttle,
for example, with the following debug patch:
+ printk("%s-%d: %s enter %llu\n", current->comm, current->pid, __func__, blk_time_get_ns());
while (true) {
set_current_state(TASK_UNINTERRUPTIBLE);
if (wait.committed)
break;
io_schedule();
}
+ printk("%s-%d: %s exit %llu\n", current->comm, current->pid, __func__, blk_time_get_ns());
It can be observerd that blk_time_get_ns() always return the same time:
[ 1068.096579] fio-1268: ioc_rqos_throttle enter 1067901962288
[ 1068.272587] fio-1268: ioc_rqos_throttle exit 1067901962288
[ 1068.274389] fio-1268: ioc_rqos_throttle enter 1067901962288
[ 1068.472690] fio-1268: ioc_rqos_throttle exit 1067901962288
[ 1068.474485] fio-1268: ioc_rqos_throttle enter 1067901962288
[ 1068.672656] fio-1268: ioc_rqos_throttle exit 1067901962288
[ 1068.674451] fio-1268: ioc_rqos_throttle enter 1067901962288
[ 1068.872655] fio-1268: ioc_rqos_throttle exit 1067901962288
And I think the root cause is that 'PF_BLOCK_TS' is always cleared
by blk_flush_plug() before scheduel(), hence blk_plug_invalidate_ts()
will never be called:
blk_time_get_ns
plug->cur_ktime = ktime_get_ns();
current->flags |= PF_BLOCK_TS;
io_schedule:
io_schedule_prepare
blk_flush_plug
__blk_flush_plug
/* the flag is cleared, while time is not */
current->flags &= ~PF_BLOCK_TS;
schedule
sched_update_worker
/* the flag is not set, hence plug->cur_ktime is not cleared */
if (tsk->flags & PF_BLOCK_TS)
blk_plug_invalidate_ts()
blk_time_get_ns
/* got the time stashed before schedule */
return plug->cur_ktime;
Fix the problem by clearing cached time in __blk_flush_plug().
Fixes: 06b23f92af ("block: update cached timestamp post schedule/preemption")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Link: https://lore.kernel.org/r/20240411032349.3051233-2-yukuai1@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
