Fix the rxrpc call expiration timeouts and make them settable from
userspace. By analogy with other rx implementations, there should be three
timeouts:
(1) "Normal timeout"
This is set for all calls and is triggered if we haven't received any
packets from the peer in a while. It is measured from the last time
we received any packet on that call. This is not reset by any
connection packets (such as CHALLENGE/RESPONSE packets).
If a service operation takes a long time, the server should generate
PING ACKs at a duration that's substantially less than the normal
timeout so is to keep both sides alive. This is set at 1/6 of normal
timeout.
(2) "Idle timeout"
This is set only for a service call and is triggered if we stop
receiving the DATA packets that comprise the request data. It is
measured from the last time we received a DATA packet.
(3) "Hard timeout"
This can be set for a call and specified the maximum lifetime of that
call. It should not be specified by default. Some operations (such
as volume transfer) take a long time.
Allow userspace to set/change the timeouts on a call with sendmsg, using a
control message:
RXRPC_SET_CALL_TIMEOUTS
The data to the message is a number of 32-bit words, not all of which need
be given:
u32 hard_timeout; /* sec from first packet */
u32 idle_timeout; /* msec from packet Rx */
u32 normal_timeout; /* msec from data Rx */
This can be set in combination with any other sendmsg() that affects a
call.
Signed-off-by: David Howells <dhowells@redhat.com>
When rxrpc_sendmsg() parses the control message buffer, it places the
parameters extracted into a structure, but lumps together call parameters
(such as user call ID) with operation parameters (such as whether to send
data, send an abort or accept a call).
Split the call parameters out into their own structure, a copy of which is
then embedded in the operation parameters struct.
The call parameters struct is then passed down into the places that need it
instead of passing the individual parameters. This allows for extra call
parameters to be added.
Signed-off-by: David Howells <dhowells@redhat.com>
Delay terminal ACK transmission on a client call by deferring it to the
connection processor. This allows it to be skipped if we can send the next
call instead, the first DATA packet of which will implicitly ack this call.
Signed-off-by: David Howells <dhowells@redhat.com>
Don't set upgrade by default when creating a call from sendmsg(). This is
a holdover from when I was testing the code.
Signed-off-by: David Howells <dhowells@redhat.com>
The caller of rxrpc_accept_call() must release the lock on call->user_mutex
returned by that function.
Signed-off-by: David Howells <dhowells@redhat.com>
Pull networking fixes from David Miller:
1) Fix PCI IDs of 9000 series iwlwifi devices, from Luca Coelho.
2) bpf offload bug fixes from Jakub Kicinski.
3) Fix bpf verifier to NOP out code which is dead at run time because
due to branch pruning the verifier will not explore such
instructions. From Alexei Starovoitov.
4) Fix crash when deleting secondary chains in packet scheduler
classifier. From Roman Kapl.
5) Fix buffer management bugs in smc, from Ursula Braun.
6) Fix regression in anycast route handling, from David Ahern.
7) Fix link settings regression in r8169, from Tobias Jakobi.
8) Add back enough UFO support so that live migration still works, from
Willem de Bruijn.
9) Linearize enough packet data for the full extent to which the ipvlan
code will inspect the packet headers, from Gao Feng.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (46 commits)
ipvlan: Fix insufficient skb linear check for ipv6 icmp
ipvlan: Fix insufficient skb linear check for arp
geneve: only configure or fill UDP_ZERO_CSUM6_RX/TX info when CONFIG_IPV6
net: dsa: bcm_sf2: Clear IDDQ_GLOBAL_PWR bit for PHY
net: accept UFO datagrams from tuntap and packet
net: realtek: r8169: implement set_link_ksettings()
net: ipv6: Fixup device for anycast routes during copy
net/smc: Fix preinitialization of buf_desc in __smc_buf_create()
net/smc: use sk_rcvbuf as start for rmb creation
ipv6: Do not consider linkdown nexthops during multipath
net: sched: fix crash when deleting secondary chains
net: phy: cortina: add missing MODULE_DESCRIPTION/AUTHOR/LICENSE
bpf: fix branch pruning logic
bpf: change bpf_perf_event_output arg5 type to ARG_CONST_SIZE_OR_ZERO
bpf: change bpf_probe_read_str arg2 type to ARG_CONST_SIZE_OR_ZERO
bpf: remove explicit handling of 0 for arg2 in bpf_probe_read
bpf: introduce ARG_PTR_TO_MEM_OR_NULL
i40evf: Use smp_rmb rather than read_barrier_depends
fm10k: Use smp_rmb rather than read_barrier_depends
igb: Use smp_rmb rather than read_barrier_depends
...
Pull x86 platform driver fixes from Darren Hart:
"Fix two issues resulting from the dell-smbios refactoring and
introduction of the dell-smbios-wmi dispatcher.
The first ensures a proper error code is returned when kzalloc fails.
The second avoids an issue in older Dell BIOS implementations which
would fail if the more complex calls were made by limiting those
platforms to the simple calls such as those used by the existing
dell-laptop and dell-wmi drivers, preserving their functionality prior
to the addition of the dell-smbios-wmi dispatcher"
* tag 'platform-drivers-x86-v4.15-2' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: dell-laptop: fix error return code in dell_init()
platform/x86: dell-smbios-wmi: Disable userspace interface if missing hotfix
Pull SCSI fixes from James Bottomley:
"Two basic fixes: one for the sparse problem with the blacklist flags
and another for a hang forever in bnx2i"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: Use 'blist_flags_t' for scsi_devinfo flags
scsi: bnx2fc: Fix hung task messages when a cleanup response is not received during abort
Pull sound fixes from Takashi Iwai:
"All commits found here are small fixes for regression or stable:
- PCM timestamp behavior fix that could be seen as a regression
- Remove spurious WARN_ON() from ALSA timer 32bit compat ioctl
- HD-audio HDMI/DP channel mapping fix for 32bit archs
- Fix the previous fix for HD-audio initialization code
- More hardening USB-audio against malicious USB descriptors
- HD-audio quirks/fixes (Realtek codec, AMD controller)
- Missing help text for the recent Intel SST kconfig change"
* tag 'sound-fix-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda: Add Raven PCI ID
ALSA: hda/realtek - Fix ALC700 family no sound issue
ALSA: hda - Fix yet remaining issue with vmaster 0dB initialization
ALSA: usb-audio: Add sanity checks in v2 clock parsers
ALSA: usb-audio: Fix potential zero-division at parsing FU
ALSA: usb-audio: Fix potential out-of-bound access at parsing SU
ALSA: usb-audio: Add sanity checks to FE parser
ALSA: timer: Remove kernel warning at compat ioctl error paths
ALSA: pcm: update tstamp only if audio_tstamp changed
ALSA: hda/realtek: Add headset mic support for Intel NUC Skull Canyon
ALSA: hda: Fix too short HDMI/DP chmap reporting
ALSA: usb-audio: uac1: Invalidate ctl on interrupt
ALSA: hda/realtek - Fix ALC275 no sound issue
ASoC: Intel: Add help text for SND_SOC_INTEL_SST_TOPLEVEL
Pull more drm updates from Dave Airlie:
"Fixes/cleanups for rc1, non-desktop flags for VR
- remove the MSM dt-bindings file Rob managed to push in the previous
pull.
- add a property/edid quirk to denote HMD devices, I had these
hanging around for a few weeks and Keith had done some work on
them, they are fairly self contained and small, and only affect
people using HTC Vive VR headsets so far.
- amdgpu, tegra, tilcdc, fsl fixes
- some imx-drm cleanups I missed, these seemed pretty small, and no
reason to hold off.
I have one TTM regression fix (fixes bochs-vga in qemu) sitting
locally awaiting review I'll probably send that in a separate pull
request tomorrow"
* tag 'drm-for-v4.15-part2' of git://people.freedesktop.org/~airlied/linux: (33 commits)
dt-bindings: remove file that was added accidentally
drm/edid: quirk HTC vive headset as non-desktop. [v2]
drm/fb: add support for not enabling fbcon on non-desktop displays [v2]
drm: add connector info/property for non-desktop displays [v2]
drm/amdgpu: fix rmmod KCQ disable failed error
drm/amdgpu: fix kernel hang when starting VNC server
drm/amdgpu: don't skip attributes when powerplay is enabled
drm/amd/pp: fix typecast error in powerplay.
drm/tilcdc: Remove obsolete "ti,tilcdc,slave" dts binding support
drm/tegra: sor: Reimplement pad clock
Revert "drm/radeon: dont switch vt on suspend"
drm/amd/amdgpu: fix over-bound accessing in amdgpu_cs_wait_any_fence
drm/amd/powerplay: fix unfreeze level smc message for smu7
drm/amdgpu:fix memleak
drm/amdgpu:fix memleak in takedown
drm/amd/pp: fix dpm randomly failed on Vega10
drm/amdgpu: set f_mapping on exported DMA-bufs
drm/amdgpu: Properly allocate VM invalidate eng v2
drm/fsl-dcu: enable IRQ before drm_atomic_helper_resume()
drm/fsl-dcu: avoid disabling pixel clock twice on suspend
...
Pull documentation updates from Jonathan Corbet:
"A few late-arriving docs updates that have no real reason to wait.
There's a new "Co-Developed-by" tag described by Greg, and a build
enhancement from Willy to generate docs warnings during a kernel build
(but only when additional warnings have been requested in general)"
* tag 'docs-4.15-2' of git://git.lwn.net/linux:
Add optional check for bad kernel-doc comments
Documentation: fix profile= options in kernel-parameters.txt
documentation/svga.txt: update outdated file
kokr/memory-barriers.txt: Fix typo in paring example
kokr/memory-barriers/txt: Replace uses of "transitive"
Documentation/process: add Co-Developed-by: tag for patches with multiple authors
Pull keys update from James Morris:
"There's nothing too controversial here:
- Doc fix for keyctl_read().
- time_t -> time64_t replacement.
- Set the module licence on things to prevent tainting"
* 'next-keys' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
pkcs7: Set the module licence to prevent tainting
security: keys: Replace time_t with time64_t for struct key_preparsed_payload
security: keys: Replace time_t/timespec with time64_t
KEYS: fix in-kernel documentation for keyctl_read()
Pull apparmor updates from John Johansen:
"No features this time, just minor cleanups and bug fixes.
Cleanups:
- fix spelling mistake: "resoure" -> "resource"
- remove unused redundant variable stop
- Fix bool initialization/comparison
Bug Fixes:
- initialized returned struct aa_perms
- fix leak of null profile name if profile allocation fails
- ensure that undecidable profile attachments fail
- fix profile attachment for special unconfined profiles
- fix locking when creating a new complain profile.
- fix possible recursive lock warning in __aa_create_ns"
* tag 'apparmor-pr-2017-11-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor:
apparmor: fix possible recursive lock warning in __aa_create_ns
apparmor: fix locking when creating a new complain profile.
apparmor: fix profile attachment for special unconfined profiles
apparmor: ensure that undecidable profile attachments fail
apparmor: fix leak of null profile name if profile allocation fails
apparmor: remove unused redundant variable stop
apparmor: Fix bool initialization/comparison
apparmor: initialized returned struct aa_perms
apparmor: fix spelling mistake: "resoure" -> "resource"
Gao Feng says:
====================
ipvlan: Fix insufficient skb linear check
The current ipvlan codes use pskb_may_pull to get the skb linear header in
func ipvlan_get_L3_hdr, but the size isn't enough for arp and ipv6 icmp.
So it may access the unexpected momory in ipvlan_addr_lookup.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In the function ipvlan_get_L3_hdr, current codes use pskb_may_pull to
make sure the skb header has enough linear room for ipv6 header. But it
would use the latter memory directly without linear check when it is icmp.
So it still may access the unepxected memory in ipvlan_addr_lookup.
Now invoke the pskb_may_pull again if it is ipv6 icmp.
Signed-off-by: Gao Feng <gfree.wind@vip.163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the function ipvlan_get_L3_hdr, current codes use pskb_may_pull to
make sure the skb header has enough linear room for arp header. But it
would access the arp payload in func ipvlan_addr_lookup. So it still may
access the unepxected memory.
Now use arp_hdr_len(port->dev) instead of the arp header as the param.
Signed-off-by: Gao Feng <gfree.wind@vip.163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefano pointed that configure or show UDP_ZERO_CSUM6_RX/TX info doesn't
make sense if we haven't enabled CONFIG_IPV6. Fix it by adding
if IS_ENABLED(CONFIG_IPV6) check.
Fixes: abe492b4f5 ("geneve: UDP checksum configuration via netlink")
Fixes: fd7eafd021 ("geneve: fix fill_info when link down")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Valo says:
====================
wireless-drivers fixes for 4.15
First set of fixes for 4.15. Most important here is the iwlwifi fix
for scan command firmware interface change.
ath10k
* fix CCMP-256, GCMP and GCMP-256 in raw mode, it was never working
wcn36xx
* fix device tree node search
iwlwifi
* fix a regression with firmware API change of scan cmd (introduced in
firmware version 34)
* add a bunch of PCI IDs and fix configuration structs for A000 devices
* fix the exported firmware name strings for 9000 and A000 devices
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Fixes 2017-11-21
This series contains fixes for igb/vf, ixgbe/vf, i40e/vf and fm10k.
Jake fixes a regression issue with older firmware, where we were using
the NVM lock to synchronize NVM reads for all devices and firmware
versions, yet this caused issues with older firmware prior to version
1.5. Fixed this by only grabbing the lock for newer devices and firmware
version 1.5 or newer.
Zijie Pan fixes the calculation of the i40e VF MAC addresses, where it was
possible to increment to the next MAC entry without calling
i40e_add_mac_filter().
Amritha removes the upper limit of 64 queues on a channel VSI since the
upper bound is determined by the VSI's num_queue_pairs.
Filip fixes an issue during FLR resets, where should have been checking
for upcoming core reset and if so, just return with I40E_ERR_NOT_READY.
Alan fixes the notifying clients of l2 parameters by copying the
parameters to the client instance struct and re-organizes the priority
in which the client tasks fire so that if the flag for notifying l2
params is set, it will trigger before the client open task. Also fixed
the promiscuous settings after reset for all the VSI's.
Brian King from IBM fixes an issue seen on Power systems which would
result in skb list corruption and eventual kernel oops. Brian
provides the same fix for nearly all our drivers, to replace the
read_barrier_depends with smp_rmb() to ensure loads are ordered with
respect to the load of tx_buffer->next_to_watch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY on BCM7278 has an additional bit that needs to be cleared:
IDDQ_GLOBAL_PWR, without doing this, the PHY remains stuck in reset out
of suspend/resume cycles.
Fixes: 0fe9933804 ("net: dsa: bcm_sf2: Add support for BCM7278 integrated switch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2017-11-23
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Several BPF offloading fixes, from Jakub. Among others:
- Limit offload to cls_bpf and XDP program types only.
- Move device validation into the driver and don't make
any assumptions about the device in the classifier due
to shared blocks semantics.
- Don't pass offloaded XDP program into the driver when
it should be run in native XDP instead. Offloaded ones
are not JITed for the host in such cases.
- Don't destroy device offload state when moved to
another namespace.
- Revert dumping offload info into user space for now,
since ifindex alone is not sufficient. This will be
redone properly for bpf-next tree.
2) Fix test_verifier to avoid using bpf_probe_write_user()
helper in test cases, since it's dumping a warning into
kernel log which may confuse users when only running tests.
Switch to use bpf_trace_printk() instead, from Yonghong.
3) Several fixes for correcting ARG_CONST_SIZE_OR_ZERO semantics
before it becomes uabi, from Gianluca. More specifically:
- Add a type ARG_PTR_TO_MEM_OR_NULL that is used only
by bpf_csum_diff(), where the argument is either a
valid pointer or NULL. The subsequent ARG_CONST_SIZE_OR_ZERO
then enforces a valid pointer in case of non-0 size
or a valid pointer or NULL in case of size 0. Given
that, the semantics for ARG_PTR_TO_MEM in combination
with ARG_CONST_SIZE_OR_ZERO are now such that in case
of size 0, the pointer must always be valid and cannot
be NULL. This fix in semantics allows for bpf_probe_read()
to drop the recently added size == 0 check in the helper
that would become part of uabi otherwise once released.
At the same time we can then fix bpf_probe_read_str() and
bpf_perf_event_output() to use ARG_CONST_SIZE_OR_ZERO
instead of ARG_CONST_SIZE in order to fix recently
reported issues by Arnaldo et al, where LLVM optimizes
two boundary checks into a single one for unknown
variables where the verifier looses track of the variable
bounds and thus rejects valid programs otherwise.
4) A fix for the verifier for the case when it detects
comparison of two constants where the branch is guaranteed
to not be taken at runtime. Verifier will rightfully prune
the exploration of such paths, but we still pass the program
to JITs, where they would complain about using reserved
fields, etc. Track such dead instructions and sanitize
them with mov r0,r0. Rejection is not possible since LLVM
may generate them for valid C code and doesn't do as much
data flow analysis as verifier. For bpf-next we might
implement removal of such dead code and adjust branches
instead. Fix from Alexei.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tuntap and similar devices can inject GSO packets. Accept type
VIRTIO_NET_HDR_GSO_UDP, even though not generating UFO natively.
Processes are expected to use feature negotiation such as TUNSETOFFLOAD
to detect supported offload types and refrain from injecting other
packets. This process breaks down with live migration: guest kernels
do not renegotiate flags, so destination hosts need to expose all
features that the source host does.
Partially revert the UFO removal from 182e0b6b5846~1..d9d30adf5677.
This patch introduces nearly(*) no new code to simplify verification.
It brings back verbatim tuntap UFO negotiation, VIRTIO_NET_HDR_GSO_UDP
insertion and software UFO segmentation.
It does not reinstate protocol stack support, hardware offload
(NETIF_F_UFO), SKB_GSO_UDP tunneling in SKB_GSO_SOFTWARE or reception
of VIRTIO_NET_HDR_GSO_UDP packets in tuntap.
To support SKB_GSO_UDP reappearing in the stack, also reinstate
logic in act_csum and openvswitch. Achieve equivalence with v4.13 HEAD
by squashing in commit 939912216f ("net: skb_needs_check() removes
CHECKSUM_UNNECESSARY check for tx.") and reverting commit 8d63bee643
("net: avoid skb_warn_bad_offload false positives on UFO").
(*) To avoid having to bring back skb_shinfo(skb)->ip6_frag_id,
ipv6_proxy_select_ident is changed to return a __be32 and this is
assigned directly to the frag_hdr. Also, SKB_GSO_UDP is inserted
at the end of the enum to minimize code churn.
Tested
Booted a v4.13 guest kernel with QEMU. On a host kernel before this
patch `ethtool -k eth0` shows UFO disabled. After the patch, it is
enabled, same as on a v4.13 host kernel.
A UFO packet sent from the guest appears on the tap device:
host:
nc -l -p -u 8000 &
tcpdump -n -i tap0
guest:
dd if=/dev/zero of=payload.txt bs=1 count=2000
nc -u 192.16.1.1 8000 < payload.txt
Direct tap to tap transmission of VIRTIO_NET_HDR_GSO_UDP succeeds,
packets arriving fragmented:
./with_tap_pair.sh ./tap_send_ufo tap0 tap1
(from https://github.com/wdebruij/kerneltools/tree/master/tests)
Changes
v1 -> v2
- simplified set_offload change (review comment)
- documented test procedure
Link: http://lkml.kernel.org/r/<CAF=yD-LuUeDuL9YWPJD9ykOZ0QCjNeznPDr6whqZ9NGMNF12Mw@mail.gmail.com>
Fixes: fb652fdfe8 ("macvlan/macvtap: Remove NETIF_F_UFO advertisement.")
Reported-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6fa1ba6152 partially
implemented the new ethtool API, by replacing get_settings()
with get_link_ksettings(). This breaks ethtool, since the
userspace tool (according to the new API specs) never tries
the legacy set() call, when the new get() call succeeds.
All attempts to chance some setting from userspace result in:
> Cannot set new settings: Operation not supported
Implement the missing set() call.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian reported a breakage with anycast routes due to commit
4832c30d54 ("net: ipv6: put host and anycast routes on device with
address"). Prior to this commit anycast routes were added against the
loopback device causing repetitive route entries with no insight into
why they existed. e.g.:
$ ip -6 ro ls table local type anycast
anycast 2001:db8:1:: dev lo proto kernel metric 0 pref medium
anycast 2001:db8:2:: dev lo proto kernel metric 0 pref medium
anycast fe80:: dev lo proto kernel metric 0 pref medium
anycast fe80:: dev lo proto kernel metric 0 pref medium
The point of commit 4832c30d54 is to add the routes using the device
with the address which is causing the route to be added. e.g.,:
$ ip -6 ro ls table local type anycast
anycast 2001:db8:1:: dev eth1 proto kernel metric 0 pref medium
anycast 2001:db8:2:: dev eth2 proto kernel metric 0 pref medium
anycast fe80:: dev eth2 proto kernel metric 0 pref medium
anycast fe80:: dev eth1 proto kernel metric 0 pref medium
For traffic to work as it did before, the dst device needs to be switched
to the loopback when the copy is created similar to local routes.
Fixes: 4832c30d54 ("net: ipv6: put host and anycast routes on device with address")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun says:
====================
net/smc: fixes for smc buffer handling
here are 2 cleanup patches for smc buffer handling.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With gcc-4.1.2:
net/smc/smc_core.c: In function ‘__smc_buf_create’:
net/smc/smc_core.c:567: warning: ‘bufsize’ may be used uninitialized in this function
Indeed, if the for-loop is never executed, bufsize is used
uninitialized. In addition, buf_desc is stored for later use, while it
is still a NULL pointer.
Before, error handling was done by checking if buf_desc is non-NULL.
The cleanup changed this to an error check, but forgot to update the
preinitialization of buf_desc to an error pointer.
Update the preinitializatin of buf_desc to fix this.
Fixes: b33982c3a6 ("net/smc: cleanup function __smc_buf_create()")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3e034725c0 ("net/smc: common functions for RMBs and send buffers")
merged handling of SMC receive and send buffers. It introduced sk_buf_size
as merged start value for size determination. But since sk_buf_size is not
used at all, sk_sndbuf is erroneously used as start for rmb creation.
This patch makes sure, sk_buf_size is really used as intended, and
sk_rcvbuf is used as start value for rmb creation.
Fixes: 3e034725c0 ("net/smc: common functions for RMBs and send buffers")
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Hans Wippel <hwippel@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the 'ignore_routes_with_linkdown' sysctl is set, we should not
consider linkdown nexthops during route lookup.
While the code correctly verifies that the initially selected route
('match') has a carrier, it does not perform the same check in the
subsequent multipath selection, resulting in a potential packet loss.
In case the chosen route does not have a carrier and the sysctl is set,
choose the initially selected route.
Fixes: 35103d1117 ("net: ipv6 sysctl option to ignore routes when nexthop link is down")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Acked-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If you flush (delete) a filter chain other than chain 0 (such as when
deleting the device), the kernel may run into a use-after-free. The
chain refcount must not be decremented unless we are sure we are done
with the chain.
To reproduce the bug, run:
ip link add dtest type dummy
tc qdisc add dev dtest ingress
tc filter add dev dtest chain 1 parent ffff: flower
ip link del dtest
Introduced in: commit f93e1cdcf4 ("net/sched: fix filter flushing"),
but unless you have KAsan or luck, you won't notice it until
commit 0dadc117ac ("cls_flower: use tcf_exts_get_net() before call_rcu()")
Fixes: f93e1cdcf4 ("net/sched: fix filter flushing")
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Roman Kapl <code@rkapl.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change resolves a new compile-time warning
when built as a loadable module:
WARNING: modpost: missing MODULE_LICENSE() in drivers/net/phy/cortina.o
see include/linux/module.h for more information
This adds the license as "GPL", which matches the header of the file.
MODULE_DESCRIPTION and MODULE_AUTHOR are also added.
Signed-off-by: Jesse Chan <jc@linux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when the verifier detects that register contains a runtime constant
and it's compared with another constant it will prune exploration
of the branch that is guaranteed not to be taken at runtime.
This is all correct, but malicious program may be constructed
in such a way that it always has a constant comparison and
the other branch is never taken under any conditions.
In this case such path through the program will not be explored
by the verifier. It won't be taken at run-time either, but since
all instructions are JITed the malicious program may cause JITs
to complain about using reserved fields, etc.
To fix the issue we have to track the instructions explored by
the verifier and sanitize instructions that are dead at run time
with NOPs. We cannot reject such dead code, since llvm generates
it for valid C code, since it doesn't do as much data flow
analysis as the verifier does.
Fixes: 17a5267067 ("bpf: verifier (add verifier core)")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
It maybe the typo for ALC700 support patch.
To fix the bit value on this patch.
Fixes: 6fbae35a31 ("ALSA: hda/realtek - Add support for new codecs ALC700/ALC701/ALC703")
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull pwm updates from Thierry Reding:
"The changes for this release include power management improvements for
the pwm-img driver, support for the backup mode on pwm-atmel-tcb as
well as support for more hardware with the R-Car and Mediatek drivers.
To round things off there's a bit of cleanup for sunxi and stm32-lp"
* tag 'pwm/for-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: stm32-lp: Remove pwm_is_enabled() check before calling pwm_disable()
pwm: mediatek: Add MT2712/MT7622 support
pwm: sunxi: Use of_device_get_match_data()
pwm: atmel-tcb: Support backup mode
dt-bindings: pwm: Add R-Car D3 device tree bindings
pwm: img: Add runtime PM
pwm: img: Add suspend / resume handling
Pull RTC updates from Alexandre Belloni:
"There is nothing scary this cycle, mostly driver fixes and updates.
The core fix has been in for a while and has been tested on multiple
kernel revisions by multiple teams.
Core:
- Fix setting the alarm to the next expiring timer
New drivers:
- Mediatek MT7622 RTC
- NXP PCF85363
- Spreadtrum SC27xx PMIC RTC
Drivers updates:
- Use generic nvmem to expose the Non volatile ram for ds1305,
ds1511, m48t86 and omap
- abx80x: solve possible race condition at probe
- armada38x: support trimming the RTC oscillator
- at91rm9200: fix reading the alarm value at boot
- ds1511: allow waking platform
- m41t80: rework square wave output
- pcf8523: support trimming the RTC oscillator
- pcf8563: fix clock output rate
- pl031: make interrupt optional
- xgene: fix suspend/resume"
* tag 'rtc-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (50 commits)
dt-bindings: rtc: imxdi: Improve the bindings text
rtc: sc27xx: Add Spreadtrum SC27xx PMIC RTC driver
dt-bindings: rtc: Add Spreadtrum SC27xx RTC documentation
rtc: at91rm9200: fix reading alarm value
rtc: at91rm9200: stop calculating yday in at91_rtc_readalarm
rtc: sysfs: Use time64_t variables to set time/alarm
rtc: xgene: mark PM functions as __maybe_unused
rtc: xgene: Fix suspend/resume
rtc: pcf8563: don't alway enable the alarm
rtc: pcf8563: fix output clock rate
rtc: rx8010: Fix for incorrect return value
rtc: rx8010: Specify correct address for RX8010_RESV31
rtc: rx8010: Remove duplicate define
rtc: m41t80: remove unneeded checks from m41t80_sqw_set_rate
rtc: m41t80: avoid i2c read in m41t80_sqw_is_prepared
rtc: m41t80: avoid i2c read in m41t80_sqw_recalc_rate
rtc: m41t80: fix m41t80_sqw_round_rate return value
rtc: m41t80: m41t80_sqw_set_rate should return 0 on success
rtc: add support for NXP PCF85363 real-time clock
rtc: omap: Support scratch registers
...
Pull MTD updates from Richard Weinberger:
"General changes:
- Unconfuse get_unmapped_area and point/unpoint driver methods
- New partition parser: sharpslpart
- Kill GENERIC_IO
- Various fixes
NAND changes:
- Add a flag to mark NANDs that require 3 address cycles to encode a
page address
- Set a default ECC/free layout when NAND_ECC_NONE is requested
- Fix a bug in panic_nand_write()
- Another batch of cleanups for the denali driver
- Fix PM support in the atmel driver
- Remove support for platform data in the omap driver
- Fix subpage write in the omap driver
- Fix irq handling in the mtk driver
- Change link order of mtk_ecc and mtk_nand drivers to speed up boot
time
- Change log level of ECC error messages in the mxc driver
- Patch the pxa3xx driver to support Armada 8k platforms
- Add BAM DMA support to the qcom driver
- Convert gpio-nand to the GPIO desc API
- Fix ECC handling in the mt29f driver
SPI-NOR changes:
- Introduce system power management support
- New mechanism to select the proper .quad_enable() hook by JEDEC
ID, when needed, instead of only by manufacturer ID
- Add support to new memory parts from Gigadevice, Winbond, Macronix
and Everspin
- Maintainance for Cadence, Intel, Mediatek and STM32 drivers"
* tag 'for-linus-20171120' of git://git.infradead.org/linux-mtd: (85 commits)
mtd: Avoid probe failures when mtd->dbg.dfs_dir is invalid
mtd: sharpslpart: Add sharpslpart partition parser
mtd: Add sanity checks in mtd_write/read_oob()
mtd: remove the get_unmapped_area method
mtd: implement mtd_get_unmapped_area() using the point method
mtd: chips/map_rom.c: implement point and unpoint methods
mtd: chips/map_ram.c: implement point and unpoint methods
mtd: mtdram: properly handle the phys argument in the point method
mtd: mtdswap: fix spelling mistake: 'TRESHOLD' -> 'THRESHOLD'
mtd: slram: use memremap() instead of ioremap()
kconfig: kill off GENERIC_IO option
mtd: Fix C++ comment in include/linux/mtd/mtd.h
mtd: constify mtd_partition
mtd: plat-ram: Replace manual resource management by devm
mtd: nand: Fix writing mtdoops to nand flash.
mtd: intel-spi: Add Intel Lewisburg PCH SPI super SKU PCI ID
mtd: nand: mtk: fix infinite ECC decode IRQ issue
mtd: spi-nor: Add support for mr25h128
mtd: nand: mtk: change the compile sequence of mtk_nand.o and mtk_ecc.o
mtd: spi-nor: enable 4B opcodes for mx66l51235l
...
Pull xfs fixes from Darrick Wong:
- Fix a memory leak in the new in-core extent map
- Refactor the xfs_dev_t conversions for easier xfsprogs porting
* tag 'xfs-4.15-merge-3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: abstract out dev_t conversions
xfs: fix memory leak in xfs_iext_free_last_leaf
Pull mode_t whack-a-mole from Al Viro:
"For all internal uses we want umode_t, which is arch-independent;
mode_t (or __kernel_mode_t, for that matter) is wrong outside of
userland ABI.
Unfortunately, that crap keeps coming back and needs to be put down
from time to time..."
* 'work.whack-a-mole' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
mode_t whack-a-mole: task_dump_owner()
Pull 9p filesystemfixes from Al Viro:
"Several 9p fixes"
* '9p-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
9p: Fix missing commas in mount options
net/9p: Switch to wait_event_killable()
fs/9p: Compare qid.path in v9fs_test_inode
I think this snuck in when I applied the patch for f97decac5f (didn't
apply cleanly, required some manual applying + git-add). It is unused
and shouldn't be here. My bad.
Fixes: f97decac5f "drm/msm: Support multiple ringbuffers"
Signed-off-by: Rob Clark <robdclark@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This uses the EDID info from my HTC Vive to mark it as
non-desktop.
v2: Change description from non-standard to non-desktop
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We don't want fbcon to get used on non-desktop dislays,
don't pass them as enabled connectors to the fb helper setup.
This prevents my HMD from getting disorted fbcon, and from
affecting other displays console.
v2: Change description from non-standard to non-desktop
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds the infrastructure needed to quirk displays
using edid and to mark them a non-desktop.
A non-desktop display is one which shouldn't normally be included
as a part of a desktop environment.
This is meant to cover head mounted devices like HTC Vive.
v2: Change description from non-standard to non-desktop, add docs
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
fixup docs
more misc amdgpu fixes.
* 'drm-next-4.15' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: fix rmmod KCQ disable failed error
drm/amdgpu: fix kernel hang when starting VNC server
drm/amdgpu: don't skip attributes when powerplay is enabled
drm/amd/pp: fix typecast error in powerplay.
Revert "drm/radeon: dont switch vt on suspend"
drm/amd/amdgpu: fix over-bound accessing in amdgpu_cs_wait_any_fence
drm/amd/powerplay: fix unfreeze level smc message for smu7
drm/amdgpu:fix memleak
drm/amdgpu:fix memleak in takedown
drm/imx: various cleanups
- Switch to drm_*_get/put() helpers
- Use correct parallel-display connector enum: DPI instead of VGA
- Remove incorrect unit name from device tree binding documentation example
- Remove an unused variable
* tag 'imx-drm-next-2017-10-18' of git://git.pengutronix.de/git/pza/linux:
gpu: ipu-v3: ipu-dc: Remove unused 'di' variable
dt-bindings: fsl-imx-drm: Remove incorrect "@di0" usage
drm/imx: parallel-display: use correct connector enum
drm/imx: switch to drm_*_get(), drm_*_put() helpers
drm/tegra: Fixes for v4.15-rc1
This includes an update to the SOR pad clock programming needed because
of some changes that went in through the clock tree.
* tag 'drm/tegra/for-4.15-rc1-fixes' of git://anongit.freedesktop.org/tegra/linux:
drm/tegra: sor: Reimplement pad clock
Gianluca Borello says:
====================
This set includes some fixes in semantics and usability issues that emerged
recently, and would be good to have them in net before the next release.
In particular, ARG_CONST_SIZE_OR_ZERO semantics was recently changed in
commit 9fd29c08e5 ("bpf: improve verifier ARG_CONST_SIZE_OR_ZERO
semantics") with the goal of letting the compiler generate simpler code
that the verifier can more easily accept.
To handle this change in semantics, a few checks in some helpers were
added, like in commit 9c019e2bc4 ("bpf: change helper bpf_probe_read arg2
type to ARG_CONST_SIZE_OR_ZERO"), and those checks are less than ideal
because once they make it into a released kernel bpf programs can start
relying on them, preventing the possibility of being removed later on.
This patch tries to fix the issue by introducing a new argument type
ARG_PTR_TO_MEM_OR_NULL that can be used for helpers that can receive a
<NULL, 0> tuple. By doing so, we can fix the semantics of the other helpers
that don't need <NULL, 0> and can just handle <!NULL, 0>, allowing the code
to get rid of those checks.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
