When a channel ctx is assigned to a link, we set the
LINK_CONTEXT_MODIFY_RATES_INFO to indicate that the rate fields are now
valid. But then we always take the rates of 2.4 GHz regardless of actual
used band.
This is because we are getting the band from bss_conf->chanctx_conf, but
this is assigned only after drv_assign_vif_chanctx returns, so we take
the bands of 2.4 GHz.
Fix it by taking the band from the iwl_mvm_link_info::phy_ctxt instead,
as this has already assigned in this point.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20240901071542.11c2d3609609.I8fa59e29b6bb38e5d06f3536d54dfb2c5d5bab11@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we de-activate a link because it started a CSA with mode=1, we want
to tell the firmware it can no longer transmit any frame for that link.
The firmware will do that on its own if the CSA indication (beacon /
action frame) was received on that same link, but with MLO, things got
more complex and the firmware can't track cross link CSA.
Tell the firmware if we de-activate a link because of CSA with mode=1 to
prevent it from transmitting, even if it is only an NDP PM=1 frame that
is part of the de-activation flow.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240901071542.4bef89d438d4.If7147a7a84054e67c05414c753d73f4e2e0e6e37@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When starting CAC in a mode other than AP mode, it return a
"WARNING: CPU: 0 PID: 63 at cfg80211_chandef_dfs_usable+0x20/0xaf [cfg80211]"
caused by the chandef.chan being null at the end of CAC.
Solution: Ensure the channel definition is set for the different modes
when starting CAC to avoid getting a NULL 'chan' at the end of CAC.
Call Trace:
? show_regs.part.0+0x14/0x16
? __warn+0x67/0xc0
? cfg80211_chandef_dfs_usable+0x20/0xaf [cfg80211]
? report_bug+0xa7/0x130
? exc_overflow+0x30/0x30
? handle_bug+0x27/0x50
? exc_invalid_op+0x18/0x60
? handle_exception+0xf6/0xf6
? exc_overflow+0x30/0x30
? cfg80211_chandef_dfs_usable+0x20/0xaf [cfg80211]
? exc_overflow+0x30/0x30
? cfg80211_chandef_dfs_usable+0x20/0xaf [cfg80211]
? regulatory_propagate_dfs_state.cold+0x1b/0x4c [cfg80211]
? cfg80211_propagate_cac_done_wk+0x1a/0x30 [cfg80211]
? process_one_work+0x165/0x280
? worker_thread+0x120/0x3f0
? kthread+0xc2/0xf0
? process_one_work+0x280/0x280
? kthread_complete_and_exit+0x20/0x20
? ret_from_fork+0x19/0x24
Reported-by: Kretschmer Mathias <mathias.kretschmer@fit.fraunhofer.de>
Signed-off-by: Issam Hamdi <ih@simonwunderlich.de>
Link: https://patch.msgid.link/20240816142418.3381951-1-ih@simonwunderlich.de
[shorten subject, remove OCB, reorder cases to match previous list]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The Lenovo Yoga Tab 3 Pro YT3-X90 has a non functional "BCM4752" ACPI
device, which uses GPIO resources which are actually necessary / used
for the sound (codec, speaker amplifier) on the Lenovo Yoga Tab 3 Pro.
If the rfkill-gpio driver loads before the sound drivers do the sound
drivers fail to load because the GPIOs are already claimed.
Add a DMI based deny list with the Lenovo Yoga Tab 3 Pro on there and
make rfkill_gpio_probe() exit with -ENODEV for devices on the DMI based
deny list.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patch.msgid.link/20240825131916.6388-1-hdegoede@redhat.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This shouldn't happen at all, since in station mode all MMPDUs
go through the TXQ for the STA, and not this function. There
may or may not be a race in mac80211 through which this might
happen for some frames while a station is being added, but in
that case we can also just drop the frame and pretend the STA
didn't exist yet.
Also, the code is simply wrong since it uses deflink, and it's
not easy to fix it since the mvmvif->ap_sta pointer cannot be
used without the mutex, and perhaps the right link might not
even be known.
Just drop the frame at that point instead of trying to fix it
up.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240808232017.45ad105dc7fe.I6d45c82e5758395d9afb8854057ded03c7dc81d7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, the driver handles SMPS decisions by tracking AP
capabilities, BT coexistence changes, sending necessary SMPS
frames to the AP, and updating firmware with RX chain info
using the RLC_CONFIG_CMD.
Starting with version 3 of the RLC_CONFIG_CMD, the firmware
takes over this responsibility. It now tracks SMPS, sends
frames, and configures the RLC.
In this patch:
1. Stop sending RLC_CONFIG_CMD when firmware supports RLC
offload (version 3), as rlc.rx_chain_info is not needed by
firmware, and no other field in the cmd is used.
2. Prevent the driver from forwarding any SMPS requests to
mac80211, i.e., the driver should not transmit SMPS frames
to the AP as firmware handles that.
3. Set NL80211_FEATURE_DYNAMIC_SMPS and NL80211_FEATURE_STATIC_SMPS
conditionally based on RLC version.
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240808232017.45da23be1f65.I0d46db82dd990a82e8a66876fe2f5310bc9513be@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we had a comeback, we will never use the default timeout values
again because comeback is never cleared.
Clear comeback if we send another association request which will allow
to start a default timer after Tx status.
The problem was seen with iwlwifi where the tx_status on the association
request is handled before the association response frame (which is the
usual case).
1) Tx assoc request 1/3
2) Rx assoc response (comeback, timeout = 1 second)
3) wait 1 second
4) Tx assoc request 2/3
5) Set timer to IEEE80211_ASSOC_TIMEOUT_LONG = 500ms (1 second after
round_up)
6) tx_status on frame sent in 4) is ignored because comeback is still
true
7) AP does not reply with assoc response
8) wait 1s <= This is where the bug is felt
9) Tx assoc request 3/3
With this fix, in step 6 we will reset the timer to
IEEE80211_ASSOC_TIMEOUT_SHORT = 100ms and we will wait only 100ms in
step 8.
Fixes: b133fdf07d ("wifi: mac80211: Skip association timeout update after comeback rejection")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20240808085916.23519-1-emmanuel.grumbach@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
According to RFC8325 4.3, Multimedia Streaming: AF31(011010, 26),
AF32(011100, 28), AF33(011110, 30) maps to User Priority = 4
and AC_VI (Video).
However, the original code remain the default three Most Significant
Bits (MSBs) of the DSCP, which makes AF3x map to User Priority = 3
and AC_BE (Best Effort).
Fixes: 6fdb8b8781 ("wifi: cfg80211: Update the default DSCP-to-UP mapping")
Signed-off-by: hhorace <hhoracehsu@gmail.com>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20240807082205.1369-1-hhoracehsu@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers may at times want to iterate their stations with a function
which requires some non-atomic operations.
ieee80211_iterate_stations_mtx() introduces an API to iterate stations
while holding that wiphy's mutex. This allows the iterating function to
do non-atomic operations safely.
Signed-off-by: Rory Little <rory@candelatech.com>
Link: https://patch.msgid.link/20240806004024.2014080-2-rory@candelatech.com
[unify internal list iteration functions]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the upper layer requests to cancel an ongoing scan, a race
is possible in which by the time the driver starts to handle the
upper layers scan cancel flow, the FW already completed handling
the scan request and the driver received the scan complete
notification but still did not handle the notification. In such a
case the FW will simply ignore the scan abort request coming from
the driver, no notification would arrive from the FW and the entire
abort flow would be considered a failure.
To better handle this, check the status code returned by the FW for
the scan abort command. In case the status indicates that
no scan was aborted, complete the scan abort flow with success, i.e.,
the scan was aborted, as the flow is expected to consume the scan
complete notification.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240825085558.483989d3baef.I3340556a222388504c6330b333360bf77d10f9e2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
